Boardcon Embedded CM1126B-P System on Module
Nā kikoʻī
| Hiʻona | Nā kikoʻī |
| CPU | ʻO Cortex-A53 Quad-core |
| DDR | 2GB LPDDR4 (a hiki i 4GB) |
| eMMC FLASH | 8GB (a hiki i 256GB) |
| Ka mana | DC 3.3V |
| MIPI DSI | 4-Alane |
| I2S | 4-CH |
| MIPI CSI | 2-CH 4-Alane |
| RGB LCD | 24bit |
| Kāmeʻa | 1-CH(DVP) a me 2-CH(CSI) |
| USB | 2-CH (USB HOST 2.0 and OTG 2.0) |
| Ethernet | 1000M GMAC |
| SDMMC | 2-CH |
| I2C | 5-CH |
| SPI | 2-CH |
| UART | 5-CH, 1-CH(DEBUG) |
| PWM | 11-CH |
| ADC IN | 4-CH |
| Ana Papa | 34 x 35mm |
Hoʻolauna
No keia Manual
Kuhi ʻia kēia manual e hāʻawi i ka mea hoʻohana me ka overview o ka papa a me kona mau pono, nā kiko'ī piha piha, a me nā kaʻina hana hoʻonohonoho. Aia kekahi ʻike palekana koʻikoʻi.
Manaʻo manaʻo a me ka hōʻano hou i kēia Manual
No ke kōkua ʻana i kā mākou mea kūʻai e hana i ka hapa nui o kā mākou huahana, ke hoʻomau nei mākou i nā kumuwaiwai hou aʻe i loaʻa ma ka Boardcon webkahua pūnaewelewww.boardcon.com, www.armdesigner.com). Hoʻopili kēia i nā manual, nā palapala noi, nā polokalamu examples, a me ka lako polokalamu a me ka lako. E nānā i kēlā me kēia manawa e ʻike i nā mea hou! Ke hoʻomaka nei mākou i ka hana ma kēia mau kumuwaiwai hou, ʻo ka manaʻo mai ka poʻe kūʻai mai ke kumu helu ʻekahi. support@armdesigner.com.
CM1126B-P Introduction
Hōʻuluʻulu manaʻo
The CM1126B-P system-on-module is equipped with Rockchip’s RV1126B-P, built with a quad-core Cortex-A53, 3.0 TOPs NPU, and RISC-V MCU. It is designed specifically for the IPC/CVR devices, AI Camera devices, intelligent interactive devices, and mini robots. High-performance and low-power solutions can help customers introduce new technologies more quickly and enhance the overall solution efficiency. The smallest size can be put on a 38board. Following the hardware revision from CM1126 (V1) to CM1126B-P (V2), where the SoC is updated to the RV1126B-P, the Reset & OTG_VBUS signals and the WIFI/BT module’s GPIO voltage must operate at a 3.3V logic level.
Nā hiʻohiʻona
Microprocessor
- Quad-core Cortex-A53 a hiki i ka 1.6GHz
- 32KB I-cache a me 32KB D-cache no kēlā me kēia kumu, 512KB L3 cache
- 3.0 TOPS ʻĀpana Kaʻina Neural
- RISC-V MCU to support 250ms fast boot
- ʻOi aku ka 12M ISP
Hui Hoʻomanaʻo
- LPDDR4 RAM a hiki i 4GB
- eMMC a hiki i 256GB
- SPI Flash a hiki i 8MB
Video Decoder/Encoder
- Kākoʻo i ka wikiō decode/encode a hiki i 4K@30fps
- Kākoʻo i ka manawa maoli decoding o H.264/265
- Kākoʻo i ka hoʻopili wikiō UHD H.264/265 manawa maoli
- Nui kiʻi a hiki i 8192×8192
Hōʻike Subsystem
- Hoʻopuka wikiō
- Kākoʻo ʻo 4 ala MIPI DSI a hiki i 2560 × 1440@60fps
- Supports 24-bit RGB parallel output
- Kiʻi ma
- Kākoʻo a hiki i ka 16-bit DVP interface
- Kākoʻo 2ch MIPI CSI 4lanes interface
I2S/PCM/ AC97
- ʻEkolu I2S/PCM interface
- Kākoʻo i ka pūʻulu Mic a hiki i ka 8ch PDM/TDM interface
- Kākoʻo i ka hoʻopuka leo PWM
USB a me PCIE
- ʻElua mau kikowaena USB 2.0
- One USB 2.0 OTG and one 2.0 USB host
Ethernet
- RTL8211F ma luna o ka moku
- Kākoʻo 10/100/1000M
I2C
- A hiki i ʻelima I2C
- Kākoʻo i ke ʻano maʻamau a me ke ʻano wikiwiki (a hiki i 400kbit/s)
SDIO
- Kākoʻo i ka protocol 2CH SDIO 3.0
SPI
- A hiki i ʻelua mau mea hoʻokele SPI,
- Pākuʻi paʻi kiʻi piha-duplex
UART
- Kākoʻo a hiki i 6 UART
- UART2 me 2 uea no ka debug mea paahana
- Hoʻokomo ʻia ʻelua FIFO 664-byte
- Kākoʻo i ke ʻano hoʻomalu kahe kaʻa no UART0/1/3/4/5
ADC
- A hiki i ʻehā mau kaha ADC
- 12-bit hoʻonā
- Voltage komo ana ma waena o 0V a 1.8V
- Kākoʻo a hiki i 1MS/ssamphelu pālolo
PWM
- ʻO 11 mau PWM ma luna o ka chip me ka hana hoʻopaneʻe
- Support 32-bit time/counter facility
- Koho IR ma PWM3/7
Hui mana
- Mana Kūʻokoʻa ma luna o ka moku
- Hoʻokahi hoʻokomo 3.3V
CM1126B-P Papa Hana
RV1126B-P Papa Hana
Papa hoʻomohala (Idea1126) Block Diagram
CM1126B-P PCB Ana
CM1126B-P Pin Wehewehe
| Pin | hōʻailona | ʻO ka wehewehe a i ʻole nā hana | GPIO serial | IO Voltage |
| 1 | LCDC_D19_3V3 | I2S1_MCLK_M2/CIF_D15_M1 | GPIO2_C7_d | 3.3V |
| 2 | LCDC_D20_3V3 | I2S1_SDO_M2/CIF_VS_M1 | GPIO2_D0_d | 3.3V |
| 3 | LCDC_D21_3V3 | I2S1_SCLK_M2/CIF_CLKO_M1 | GPIO2_D1_d | 3.3V |
| 4 | LCDC_D22_3V3 | I2S1_LRCK_M2/CIF_CKIN_M1 | GPIO2_D2_d | 3.3V |
| 5 | LCDC_D23_3V3 | I2S1_SDI_M2/CIF_HS_M1 | GPIO2_D3_d | 3.3V |
| 6 | GND | Ka honua | 0V | |
| 7 | GPIO1_D1 | UART1_RX_M1/I2C5_SDA_M2 | GPIO1_D1_d | 3.3V(V2) |
| 8 | BT_WAKE | SPI0_CS1n_M0 | GPIO0_A4_u | 3.3V(V2) |
| 9 | WIFI_REG_ON | SPI0_MOSI_M0 | GPIO0_A6_d | 3.3V(V2) |
| 10 | BT_RST | SPI0_MISO_M0 | GPIO0_A7_d | 3.3V(V2) |
| 11 | WIFI_WAKE_HOST | SPI0_CLK_M0 | GPIO0_B0_d | 3.3V(V2) |
| 12 | BT_WAKE_HOST | SPI0_CS0n_M0 | GPIO0_A5_u | 3.3V(V2) |
| 13 | PWM7_IR_M0_3V3 | GPIO0_B1_d | 3.3V | |
| 14 | PWM6_M0_3V3 | TSADC_SHUT_M1 | GPIO0_B2_d | 3.3V |
| 15 | UART2_TX_3V3 | No ka debug | GPIO3_A2_u | 3.3V |
| 16 | UART2_RX_3V3 | No ka debug | GPIO3_A3_u | 3.3V |
| 17 | I2S0_MCLK_M0_3V
3 |
GPIO3_D2_d | 3.3V | |
| 18 | I2S0_SCLK_TX_M0
_3V3 |
ACODEC_DAC_CLK | GPIO3_D0_d | 3.3V |
| 19 | I2S0_SDI3_M0_3V3 | PDM_SDI3_M0 /
ACODEC_ADC_DATA |
GPIO3_D7_d | 3.3V |
| 20 | I2S0_SDO0_M0_3V
3 |
ACODEC_DAC_DATAR
/APWM_R_M1/ADSM_LP |
GPIO3_D5_d | 3.3V |
| Pin | hōʻailona | ʻO ka wehewehe a i ʻole nā hana | GPIO serial | IO Voltage |
| 21 | I2S0_LRCK_TX_M0
_3V3 |
ACODEC_DAC_SYNC
/APWM_L_M1/ADSM_LN |
GPIO3_D3_d | 3.3V |
| 22 | PDM_SDI1_3V3 | I2S0_SDO3_SDI1_M0/I2C4SDA | GPIO4_A1_d | 3.3V |
| 23 | PDM_CLK1_3V3 | I2S0_SCK_RX_M0 | GPIO3_D1_d | 3.3V |
| 24 | PDM_SDI2_3V3 | I2S0_SDO2_SDI2_M0/I2C4SCL | GPIO4_A0_d | 3.3V |
| 25 | PDM_SDI0_3V3 | I2S0_SDI0_M0 | GPIO3_D6_d | 3.3V |
| 26 | PDM_CLK_3V3 | I2S0_LRCK_RX_M0 | GPIO3_D4_d | 3.3V |
| 27 | I2C2_SDA_3V3 | PWM5_M0 | GPIO0_C3_d | 3.3V |
| 28 | I2C2_SCL_3V3 | PWM4_M0 | GPIO0_C2_d | 3.3V |
| 29 | USB_HOST_DP | 1.8V | ||
| 30 | USB_HOST_DM | 1.8V | ||
| 31 | GND | Ka honua | 0V | |
| 32 | OTG_DP | Hiki ke hoʻohana ʻia no ka hoʻoiho ʻana | 1.8V | |
| 33 | OTG_DM | Hiki ke hoʻohana ʻia no ka hoʻoiho ʻana | 1.8V | |
| 34 | OTG_DET(V2) | OTG VBUS DET IN | 3.3V(V2) | |
| 35 | OTG_ID | 1.8V | ||
| 36 | SPI0_CS1n_M1 | I2S1_MCK_M1/UART4_TX_M2 | GPIO1_D5_d | 1.8V |
| 37 | VCC3V3_SYS | 3.3V Main Mana komo | 3.3V | |
| 38 | VCC3V3_SYS | 3.3V Main Mana komo | 3.3V | |
| 39 | USB_CTRL_3V3 | GPIO0_C1_d | 3.3V | |
| 40 | SDMMC0_DET | Pono e hoʻohana ʻia no ke kāleka SD | GPIO0_A3_u | 3.3V(V2) |
| 41 | CLKO_32K | Hoʻopuka uaki RTC | GPIO0_A2_u | 3.3V(V2) |
| 42 | nRESET | Hoʻihoʻi hou i ka hoʻokomo kī | 3.3V(V2) | |
| 43 | MIPI_CSI_RX0_CL
KP |
MIPI CSI0 a i ʻole LVDS0 komo | 1.8V | |
| 44 | MIPI_CSI_RX0_CL
KN |
MIPI CSI0 a i ʻole LVDS0 komo | 1.8V | |
| 45 | MIPI_CSI_RX0_D2
P |
MIPI CSI0 a i ʻole LVDS0 komo | 1.8V | |
| 46 | MIPI_CSI_RX0_D2
N |
MIPI CSI0 a i ʻole LVDS0 komo | 1.8V | |
| 47 | MIPI_CSI_RX0_D3
P |
MIPI CSI0 a i ʻole LVDS0 komo | 1.8V | |
| 48 | MIPI_CSI_RX0_D3
N |
MIPI CSI0 a i ʻole LVDS0 komo | 1.8V | |
| 49 | MIPI_CSI_RX0_D1
P |
MIPI CSI0 a i ʻole LVDS0 komo | 1.8V | |
| 50 | MIPI_CSI_RX0_D1
N |
MIPI CSI0 a i ʻole LVDS0 komo | 1.8V | |
| 51 | MIPI_CSI_RX0_D0
P |
MIPI CSI0 a i ʻole LVDS0 komo | 1.8V |
| Pin | hōʻailona | ʻO ka wehewehe a i ʻole nā hana | GPIO serial | IO Voltage |
| 52 | MIPI_CSI_RX0_D0
N |
MIPI CSI0 a i ʻole LVDS0 komo | 1.8V | |
| 53 | GND | Ka honua | 0V | |
| 54 | MIPI_CSI_RX1_D3
P |
MIPI CSI1 a i ʻole LVDS1 komo | 1.8V | |
| 55 | MIPI_CSI_RX1_D3
N |
MIPI CSI1 a i ʻole LVDS1 komo | 1.8V | |
| 56 | MIPI_CSI_RX1_CL
KP |
MIPI CSI1 a i ʻole LVDS1 komo | 1.8V | |
| 57 | MIPI_CSI_RX1_CL
KN |
MIPI CSI1 a i ʻole LVDS1 komo | 1.8V | |
| 58 | MIPI_CSI_RX1_D2
P |
MIPI CSI1 a i ʻole LVDS1 komo | 1.8V | |
| 59 | MIPI_CSI_RX1_D2
N |
MIPI CSI1 a i ʻole LVDS1 komo | 1.8V | |
| 60 | MIPI_CSI_RX1_D1
P |
MIPI CSI1 a i ʻole LVDS1 komo | 1.8V | |
| 61 | MIPI_CSI_RX1_D1
N |
MIPI CSI1 a i ʻole LVDS1 komo | 1.8V | |
| 62 | MIPI_CSI_RX1_D0
P |
MIPI CSI1 a i ʻole LVDS1 komo | 1.8V | |
| 63 | MIPI_CSI_RX1_D0
N |
MIPI CSI1 a i ʻole LVDS1 komo | 1.8V | |
| 64 | SDMMC0_D3_3V3 | UART3_TX_M1 | GPIO1_A7_u | 3.3V |
| 65 | SDMMC0_D2_3V3 | UART3_RX_M1 | GPIO1_A6_u | 3.3V |
| 66 | SDMMC0_D1_3V3 | UART2_TX_M0 | GPIO1_A5_u | 3.3V |
| 67 | SDMMC0_D0_3V3 | UART2_RX_M0 | GPIO1_A4_u | 3.3V |
| 68 | SDMMC0_CMD_3V
3 |
UART3_CTSn_M1 | GPIO1_B1_u | 3.3V |
| 69 | SDMMC0_CLK_3V3 | UART3_RTSn_M1 | GPIO1_B0_u | 3.3V |
| 70 | GND | Ka honua | 0V | |
| 71 | LED1/CFG_LDO0 | LED LINK Ethernet | 3.3V | |
| 72 | LED2/CFG_LDO1 | LED SPEED Ethernet | 3.3V | |
| 73 | MDI0 + | Hōʻailona MDI Ethernet | 1.8V | |
| 74 | MDI0- | Hōʻailona MDI Ethernet | 1.8V | |
| 75 | MDI1 + | Hōʻailona MDI Ethernet | 1.8V | |
| 76 | MDI1- | Hōʻailona MDI Ethernet | 1.8V | |
| 77 | MDI2 + | Hōʻailona MDI Ethernet | 1.8V | |
| 78 | MDI2- | Hōʻailona MDI Ethernet | 1.8V | |
| 79 | MDI3 + | Hōʻailona MDI Ethernet | 1.8V | |
| 80 | MDI3- | Hōʻailona MDI Ethernet | 1.8V | |
| 81 | I2C1_SCL | UART4_CTSn_M2 | GPIO1_D3_u | 1.8V |
| Pin | hōʻailona | ʻO ka wehewehe a i ʻole nā hana | GPIO serial | IO Voltage |
| 82 | I2C1_SDA | UART4_RTSn_M2 | GPIO1_D2_u | 1.8V |
| 83 | MIPI_CSI_PWDN0 | UART4_RX_M2 | GPIO1_D4_d | 1.8V |
| 84 | SPI0_CLK_M1 | I2S1_SDO_M1/UART5_RX_M2 | GPIO2_A1_d | 1.8V |
| 85 | SPI0_MOSI_M1 | I2S1_SCK_M1/I2C3_SCL_M2 | GPIO1_D6_d | 1.8V |
| 86 | SPI0_CS0n_M1 | I2S1_SDI_M1/UART5_TX_M2 | GPIO2_A0_d | 1.8V |
| 87 | SPI0_MISO_M1 | I2S1_LRCK_M1/I2C3_SDA_M2 | GPIO1_D7_d | 1.8V |
| 88 | MIPI_CSI_CLK1 | UART5_RTSn_M2 | GPIO2_A2_d | 1.8V |
| 89 | MIPI_CSI_CLK0 | UART5_CTSn_M2 | GPIO2_A3_d | 1.8V |
| 90 | GND | Ka honua | 0V | |
| 91 | LCDC_D0_3V3 | UART4_RTSn_M1/CIF_D0_M1 | GPIO2_A4_d | 3.3V |
| 92 | LCDC_D1_3V3 | UART4_CTSn_M1/CIF_D1_M1 | GPIO2_A5_d | 3.3V |
| 93 | LCDC_D2_3V3 | UART4_TX_M1/CIF_D2_M1 | GPIO2_A6_d | 3.3V |
| 94 | LCDC_D3_3V3 | UART4_RX_M1/I2S2_SDO_M1 | GPIO2_A7_d | 3.3V |
| 95 | LCDC_D4_3V3 | UART5_TX_M1/I2S2_SDI_M1 | GPIO2_B0_d | 3.3V |
| 96 | LCDC_D5_3V3 | UART5_RX_M1/I2S2_SCK_M1 | GPIO2_B1_d | 3.3V |
| 97 | LCDC_D6_3V3 | UART5_RTSn_M1/I2S2_LRCK_
M1 |
GPIO2_B2_d | 3.3V |
| 98 | LCDC_D7_3V3 | UART5_CTSn_M1/I2S2_MCLK_
M1/CIF_D3_M1 |
GPIO2_B3_d | 3.3V |
| 99 | CAN_RX_3V3 | UART3_TX_M2/I2C4_SCL_M0 | GPIO3_A0_u | 3.3V |
| 100 | CAN_TX_3V3 | UART3_RX_M2/I2C4_SDA_M0 | GPIO3_A1_u | 3.3V |
| 101 | LCDC_CLK_3V3 | UART3_CTSn_M2/SPI1_MISO_
M2/PWM8_M1 |
GPIO2_D7_d | 3.3V |
| 102 | LCDC_VSYNC_3V3 | UART3_RTSn_M2/SPI1_MOSI | GPIO2_D6_d | 3.3V |
| 103 | MIPI_DSI_D2P | 1.8V | ||
| 104 | MIPI_DSI_D2N | 1.8V | ||
| 105 | MIPI_DSI_D1P | 1.8V | ||
| 106 | MIPI_DSI_D1N | 1.8V | ||
| 107 | MIPI_DSI_D0P | 1.8V | ||
| 108 | MIPI_DSI_D0N | 1.8V | ||
| 109 | MIPI_DSI_D3P | 1.8V | ||
| 110 | MIPI_DSI_D3N | 1.8V | ||
| 111 | MIPI_DSI_CLKP | 1.8V | ||
| 112 | MIPI_DSI_CLKN | 1.8V | ||
| 113 | ADCIN3 | Hoʻokomo o ADC | 1.8V | |
| 114 | ADCIN2 | Hoʻokomo o ADC | 1.8V | |
| 115 | ADCIN1 | Hoʻokomo o ADC | 1.8V | |
| 116 | ADKEY_IN0 | Hoʻonohonoho ʻia ke ʻano hoʻihoʻi (10K PU) | 1.8V | |
| 117 | GND | Ka honua | 0V | |
| 118 | SDIO_CLK | GPIO1_B2_d | 3.3V(V2) | |
| 119 | SDIO_CMD | GPIO1_B3_u | 3.3V(V2) |
| Pin | hōʻailona | ʻO ka wehewehe a i ʻole nā hana | GPIO serial | IO Voltage |
| 120 | SDIO_D0 | GPIO1_B4_u | 3.3V(V2) | |
| 121 | SDIO_D1 | GPIO1_B5_u | 3.3V(V2) | |
| 122 | SDIO_D2 | GPIO1_B6_u | 3.3V(V2) | |
| 123 | SDIO_D3 | GPIO1_B7_u | 3.3V(V2) | |
| 124 | UART0_RX | GPIO1_C2_u | 3.3V(V2) | |
| 125 | UART0_TX | GPIO1_C3_u | 3.3V(V2) | |
| 126 | UART0_CTSN | GPIO1_C1_u | 3.3V(V2) | |
| 127 | UART0_RTSN | GPIO1_C0_u | 3.3V(V2) | |
| 128 | PCM_TX | I2S2_SDO_M0/SPI1_MOSI_M1 | GPIO1_C4_d | 3.3V(V2) |
| 129 | PCM_SYNC | I2S2_LRCK_M0/SPI1_CSn0_M
1/UART1_CTSn_M1 |
GPIO1_C7_d | 3.3V(V2) |
| 130 | PCM_CLK | I2S2_SCLK_M0/SPI1_CLK_M1/
UART1_RTSn_M1 |
GPIO1_C6_d | 3.3V(V2) |
| 131 | PCM_RX | I2S2_SDI_M0/SPI1_MISO_M1 | GPIO1_C5_d | 3.3V(V2) |
| 132 | LCDC_D15_3V3 | CIF_D11_M1 | GPIO2_C3_d | 3.3V |
| 133 | LCDC_D14_3V3 | CIF_D10_M1 | GPIO2_C2_d | 3.3V |
| 134 | LCDC_D13_3V3 | CIF_D9_M1 | GPIO2_C1_d | 3.3V |
| 135 | LCDC_D12_3V3 | CIF_D8_M1 | GPIO2_C0_d | 3.3V |
| 136 | LCDC_DEN_3V3 | I2C3_SCL_M1/SPI1_CS0n_M2 | GPIO2_D4_d | 3.3V |
| 137 | LCDC_D10_3V3 | CIF_D6_M1 | GPIO2_B6_d | 3.3V |
| 138 | LCDC_D9_3V3 | CIF_D5_M1 | GPIO2_B5_d | 3.3V |
| 139 | LCDC_D8_3V3 | CIF_D4_M1 | GPIO2_B4_d | 3.3V |
| 140 | LCDC_D11_3V3 | CIF_D7_M1 | GPIO2_B7_d | 3.3V |
| 141 | LCDC_HSYNC_3V3 | I2C3_SDA_M1/SPI1_CLK_M2 | GPIO2_D5_d | 3.3V |
| 142 | LCDC_D16_3V3 | CIF_D12_M1 | GPIO2_C4_d | 3.3V |
| 143 | LCDC_D17_3V3 | CIF_D13_M1 | GPIO2_C5_d | 3.3V |
| 144 | LCDC_D18_3V3 | CIF_D14_M1 | GPIO2_C6_d | 3.3V |
| Nānā:
1. ʻO ka hapa nui o GPIO voltagʻo 1.8V, akā ua kaha ʻia kekahi mau pine 3.3V. 2. GPIO voltage hoʻololi i 3.3V no ka kaha ʻia (V2). |
||||
Mea Hoʻomohala (Manaʻo1126)
Alakaʻi Hoʻolālā Lako
Kuhikuhi Kaapuni Kaapuni
Kaapuni Mana Nui
Kaapuni Debug
USB OTG Interface Circuit
PCB kapuai
Nā hiʻohiʻona uila huahana
ʻO ka hoʻopau ʻana a me ka Mahana
| hōʻailona | ʻĀpana | Min | ʻAno | Max | Unite |
| VCC3V3_SYS | Pūnaehana IO
Voltage |
3.3-5% | 3.3 | 3.3 + 5% | V |
| Isys_in | VCC3V3_SYS komo i kēia manawa | 850 | mA | ||
| Ta | Ka Mahana Hana | -20 | 70 | °C | |
| ʻO Tstg | Ka Mahana Waihona | -40 | 85 | °C |
Pono o ka ho'āʻo
| ʻO ka hoʻāʻo ʻana i ka wela wela | ||
| ʻIkepili | Ke hana nei i 8h ma nā wela kiʻekiʻe | 55°C±2°C |
| Ka hopena | TBD |
| Ho'āʻo Ola Ola | ||
| ʻIkepili | Ke hana nei i loko o ka lumi | 120h |
| Ka hopena | TBD |
Palekana Palekana
Boardcon warrants this product to be free of defects in material and workmanship for one year from the date of purchase. During this warranty period, Boardcon will repair or replace the defective unit by the following process: A copy of the original invoice must be included when returning the defective unit to Boardcon. This limited warranty does not cover damages resulting from lightning or other power surges, misuse, abuse, abnormal conditions of operation, or attempts to alter or modify the function of the product. This warranty is limited to the repair or replacement of the defective unit. In no event shall Boardcon be liable or responsible for any loss or damages, including but not limited to any lost profits, incidental or consequential damages, loss of business, or anticipatory profits arising from the use or inability to use this product. Repairs made after the expiration of the warranty period are subject to a repair charge and the cost of return shipping. Please contact Boardcon to arrange for any repair service and to obtain repair charge information.
FAQs
Q: How do I upgrade the DDR memory on CM1126B-P?
A: The CM1126B-P supports up to 4GB LPDDR4 memory. To upgrade, ensure compatibility with the specifications and follow recommended procedures.
Q: What is the power supply requirement for CM1126B-P?
A: The power requirement for CM1126B-P is DC 3.3V. Ensure to provide a stable power supply within this range for optimal performance.
Q: Can I expand the storage capacity of eMMC on CM1126B-P?
A: Yes, the eMMC storage on CM1126B-P can be expanded up to 256GB. Ensure compatibility with supported storage devices before upgrading.
Palapala / Punawai
 |
Boardcon Embedded CM1126B-P System on Module [pdf] Palapala Hoʻohana V2.20250422, CM1126B-P System on Module, CM1126B-P, System on Module, Module |