Siostam CM1126B-P leabaithe Boardcon air Modúl
Sònrachaidhean
| Feart | Sònrachaidhean |
| CPU | Quad-cridhe Cortex-A53 |
| DDR | 2GB LPDDR4 (suas gu 4GB) |
| eMMC Flash | 8GB (suas gu 256GB) |
| Cumhachd | DC 3.3V |
| MIPI DSI | 4-Latha |
| I2S | 4-CH |
| MIPI CSI | 2-CH 4-Lane |
| RGB LCD | 24 bit |
| Camara | 1-CH(DVP) agus 2-CH(CSI) |
| USB | 2-CH (USB HOST 2.0 and OTG 2.0) |
| Ethernet | 1000M GMAC |
| SDMMC | 2-CH |
| I2C | 5-CH |
| SPI | 2-CH |
| UART | 5-CH, 1-CH(DEBUG) |
| PWM | 11-CH |
| ADC IN | 4-CH |
| Meud a 'Bhùird | 34 x 35mm |
Ro-ràdh
Mun Leabhar-làimhe seo
Tha an leabhar-làimhe seo ag amas air còrr a thoirt don neach-cleachdaidhview of the board and its benefits, complete feature specifications, and setup procedures. It contains important safety information as well.
Fios air ais agus ùrachadh don Leabhar-làimhe seo
Gus ar teachdaichean a chuideachadh gus am feum as fheàrr a dhèanamh de na stuthan againn, tha sinn an-còmhnaidh a’ toirt seachad goireasan a bharrachd agus ùraichte air a’ Boardcon weblàrach (www.boardcon.com, www.armdesigner.com). Nam measg tha leabhraichean-làimhe, notaichean tagraidh, prògramadh examples, agus bathar-bog is bathar-cruaidh ùraichte. Thig a-steach bho àm gu àm gus faicinn dè tha ùr! Nuair a tha sinn a’ toirt prìomhachas do dh’ obair air na goireasan ùraichte sin, is e fios air ais bho luchd-ceannach am prìomh bhuaidh, Ma tha ceistean, beachdan no draghan agad mun toradh no am pròiseact agad, na bi leisg fios a chuir thugainn aig taic@armdesigner.com.
CM1126B-P Introduction
Geàrr-chunntas
The CM1126B-P system-on-module is equipped with Rockchip’s RV1126B-P, built with a quad-core Cortex-A53, 3.0 TOPs NPU, and RISC-V MCU. It is designed specifically for the IPC/CVR devices, AI Camera devices, intelligent interactive devices, and mini robots. High-performance and low-power solutions can help customers introduce new technologies more quickly and enhance the overall solution efficiency. The smallest size can be put on a 38board. Following the hardware revision from CM1126 (V1) to CM1126B-P (V2), where the SoC is updated to the RV1126B-P, the Reset & OTG_VBUS signals and the WIFI/BT module’s GPIO voltagFeumaidh e obrachadh aig ìre loidigeach 3.3V.
Feartan
Microprocessor
- Quad-core Cortex-A53 suas gu 1.6GHz
- 32KB I-cache agus 32KB D-cache airson gach cridhe, tasgadan 512KB L3
- 3.0 TOPS Aonad Pròiseas Neural
- RISC-V MCU to support 250ms fast boot
- ISP 12M aig a’ char as àirde
Buidheann Cuimhne
- LPDDR4 RAM suas gu 4GB
- eMMC suas gu 256GB
- SPI Flash suas gu 8MB
Decoder / encoder bhidio
- A ’toirt taic do chòdachadh / còdachadh bhidio suas gu 4K@30fps
- A’ toirt taic do chòdachadh fìor-ùine de H.264/265
- A’ toirt taic do chòdachadh bhidio UHD H.264/265 fìor-ùine
- Meud dealbh suas gu 8192 × 8192
Fo-shiostam taisbeanaidh
- Toradh bhidio
- A’ toirt taic do 4 lannan MIPI DSI suas gu 2560 × 1440@60fps
- Supports 24-bit RGB parallel output
- Dealbh a-steach
- Supports up to 16-bit DVP interface
- A’ toirt taic do eadar-aghaidh 2ch MIPI CSI 4lanes
I2S/PCM/AC97
- Trì eadar-aghaidh I2S / PCM
- Cuir taic ri raon Mic Suas gu eadar-aghaidh 8ch PDM / TDM
- Cuir taic ri toradh claisneachd PWM
USB agus PCIE
- Dà eadar-aghaidh USB 2.0
- One USB 2.0 OTG and one 2.0 USB host
Ethernet
- RTL8211F air bòrd
- Taic 10/100/1000M
I2C
- Suas ri còig I2C
- Cuir taic ri modh àbhaisteach agus modh luath (suas gu 400kbit / s)
SDIO
- Thoir taic do phròtacal 2CH SDIO 3.0
SPI
- Suas ri dà riaghladair SPI,
- Eadar-aghaidh sreathach sioncronaich làn-duplex
UART
- Thoir taic do suas ri 6 UARTs
- UART2 le 2 uèir airson innealan deasbaid
- Embedded two 664-byte FIFOs
- Cuir taic ri modh smachd sruthadh fèin-ghluasadach airson UART0/1/3/4/5
ADC
- Suas ri ceithir seanalan ADC
- Fuasgladh 12-bit
- Voltage raon cuir a-steach eadar 0V gu 1.8V
- Taic suas gu 1MS / ssampìre ling
PWM
- 11 PWM air-chip le gnìomhachd stèidhichte air briseadh
- Support 32-bit time/counter facility
- Roghainn IR air PWM3/7
Aonad cumhachd
- Cumhachd air leth air bòrd
- Cuir a-steach singilte 3.3V
Diagram Bloc CM1126B-P
RV1126B-P Block Diagram
Diagram Bloc Bòrd Leasachaidh (Idea1126)
Meud PCB CM1126B-P
Mìneachadh Prìne CM1126B-P
| Pinn | Comharradh | Tuairisgeul no gnìomhan | Sreath GPIO | IO Voltage |
| 1 | LCDC_D19_3V3 | I2S1_MCLK_M2/CIF_D15_M1 | GPIO2_C7_d | 3.3V |
| 2 | LCDC_D20_3V3 | I2S1_SDO_M2/CIF_VS_M1 | GPIO2_D0_d | 3.3V |
| 3 | LCDC_D21_3V3 | I2S1_SCLK_M2/CIF_CLKO_M1 | GPIO2_D1_d | 3.3V |
| 4 | LCDC_D22_3V3 | I2S1_LRCK_M2/CIF_CKIN_M1 | GPIO2_D2_d | 3.3V |
| 5 | LCDC_D23_3V3 | I2S1_SDI_M2/CIF_HS_M1 | GPIO2_D3_d | 3.3V |
| 6 | GND | Talamh | 0V | |
| 7 | GPIO1_D1 | UART1_RX_M1/I2C5_SDA_M2 | GPIO1_D1_d | 3.3V (V2) |
| 8 | BT_WAKE | SPI0_CS1n_M0 | GPIO0_A4_u | 3.3V (V2) |
| 9 | WIFI_REG_ON | SPI0_MOSI_M0 | GPIO0_A6_d | 3.3V (V2) |
| 10 | BT_RST | SPI0_MISO_M0 | GPIO0_A7_d | 3.3V (V2) |
| 11 | WIFI_WAKE_HOST | SPI0_CLK_M0 | GPIO0_B0_d | 3.3V (V2) |
| 12 | BT_WAKE_HOST | SPI0_CS0n_M0 | GPIO0_A5_u | 3.3V (V2) |
| 13 | PWM7_IR_M0_3V3 | GPIO0_B1_d | 3.3V | |
| 14 | PWM6_M0_3V3 | TSADC_SHUT_M1 | GPIO0_B2_d | 3.3V |
| 15 | UART2_TX_3V3 | Airson debug | GPIO3_A2_u | 3.3V |
| 16 | UART2_RX_3V3 | Airson debug | GPIO3_A3_u | 3.3V |
| 17 | I2S0_MCLK_M0_3V
3 |
GPIO3_D2_d | 3.3V | |
| 18 | I2S0_SCLK_TX_M0
_3V3 |
ACODEC_DAC_CLK | GPIO3_D0_d | 3.3V |
| 19 | I2S0_SDI3_M0_3V3 | PDM_SDI3_M0 /
ACODEC_ADC_DATA |
GPIO3_D7_d | 3.3V |
| 20 | I2S0_SDO0_M0_3V
3 |
ACODEC_DAC_DATAR
/APWM_R_M1/ADSM_LP |
GPIO3_D5_d | 3.3V |
| Pinn | Comharradh | Tuairisgeul no gnìomhan | Sreath GPIO | IO Voltage |
| 21 | I2S0_LRCK_TX_M0
_3V3 |
ACODEC_DAC_SYNC
/APWM_L_M1/ADSM_LN |
GPIO3_D3_d | 3.3V |
| 22 | PDM_SDI1_3V3 | I2S0_SDO3_SDI1_M0/I2C4SDA | GPIO4_A1_d | 3.3V |
| 23 | PDM_CLK1_3V3 | I2S0_SCK_RX_M0 | GPIO3_D1_d | 3.3V |
| 24 | PDM_SDI2_3V3 | I2S0_SDO2_SDI2_M0/I2C4SCL | GPIO4_A0_d | 3.3V |
| 25 | PDM_SDI0_3V3 | I2S0_SDI0_M0 | GPIO3_D6_d | 3.3V |
| 26 | PDM_CLK_3V3 | I2S0_LRCK_RX_M0 | GPIO3_D4_d | 3.3V |
| 27 | I2C2_SDA_3V3 | PWM5_M0 | GPIO0_C3_d | 3.3V |
| 28 | I2C2_SCL_3V3 | PWM4_M0 | GPIO0_C2_d | 3.3V |
| 29 | USB_HOST_DP | 1.8V | ||
| 30 | USB_HOST_DM | 1.8V | ||
| 31 | GND | Talamh | 0V | |
| 32 | OTG_DP | Can be used for download | 1.8V | |
| 33 | OTG_DM | Can be used for download | 1.8V | |
| 34 | OTG_DET(V2) | OTG VBUS DET IN | 3.3V (V2) | |
| 35 | OTG_ID | 1.8V | ||
| 36 | SPI0_CS1n_M1 | I2S1_MCK_M1/UART4_TX_M2 | GPIO1_D5_d | 1.8V |
| 37 | VCC3V3_SYS | Cuir a-steach prìomh chumhachd 3.3V | 3.3V | |
| 38 | VCC3V3_SYS | Cuir a-steach prìomh chumhachd 3.3V | 3.3V | |
| 39 | USB_CTRL_3V3 | GPIO0_C1_d | 3.3V | |
| 40 | SDMMC0_DET | Feumar a chleachdadh airson cairt SD | GPIO0_A3_u | 3.3V (V2) |
| 41 | CLKO_32K | Toradh uaireadair RTC | GPIO0_A2_u | 3.3V (V2) |
| 42 | nRESET | Ath-shuidhich iuchair a-steach | 3.3V (V2) | |
| 43 | MIPI_CSI_RX0_CL
KP |
Cuir a-steach MIPI CSI0 no LVDS0 | 1.8V | |
| 44 | MIPI_CSI_RX0_CL
KN |
Cuir a-steach MIPI CSI0 no LVDS0 | 1.8V | |
| 45 | MIPI_CSI_RX0_D2
P |
Cuir a-steach MIPI CSI0 no LVDS0 | 1.8V | |
| 46 | MIPI_CSI_RX0_D2
N |
Cuir a-steach MIPI CSI0 no LVDS0 | 1.8V | |
| 47 | MIPI_CSI_RX0_D3
P |
Cuir a-steach MIPI CSI0 no LVDS0 | 1.8V | |
| 48 | MIPI_CSI_RX0_D3
N |
Cuir a-steach MIPI CSI0 no LVDS0 | 1.8V | |
| 49 | MIPI_CSI_RX0_D1
P |
Cuir a-steach MIPI CSI0 no LVDS0 | 1.8V | |
| 50 | MIPI_CSI_RX0_D1
N |
Cuir a-steach MIPI CSI0 no LVDS0 | 1.8V | |
| 51 | MIPI_CSI_RX0_D0
P |
Cuir a-steach MIPI CSI0 no LVDS0 | 1.8V |
| Pinn | Comharradh | Tuairisgeul no gnìomhan | Sreath GPIO | IO Voltage |
| 52 | MIPI_CSI_RX0_D0
N |
Cuir a-steach MIPI CSI0 no LVDS0 | 1.8V | |
| 53 | GND | Talamh | 0V | |
| 54 | MIPI_CSI_RX1_D3
P |
Cuir a-steach MIPI CSI1 no LVDS1 | 1.8V | |
| 55 | MIPI_CSI_RX1_D3
N |
Cuir a-steach MIPI CSI1 no LVDS1 | 1.8V | |
| 56 | MIPI_CSI_RX1_CL
KP |
Cuir a-steach MIPI CSI1 no LVDS1 | 1.8V | |
| 57 | MIPI_CSI_RX1_CL
KN |
Cuir a-steach MIPI CSI1 no LVDS1 | 1.8V | |
| 58 | MIPI_CSI_RX1_D2
P |
Cuir a-steach MIPI CSI1 no LVDS1 | 1.8V | |
| 59 | MIPI_CSI_RX1_D2
N |
Cuir a-steach MIPI CSI1 no LVDS1 | 1.8V | |
| 60 | MIPI_CSI_RX1_D1
P |
Cuir a-steach MIPI CSI1 no LVDS1 | 1.8V | |
| 61 | MIPI_CSI_RX1_D1
N |
Cuir a-steach MIPI CSI1 no LVDS1 | 1.8V | |
| 62 | MIPI_CSI_RX1_D0
P |
Cuir a-steach MIPI CSI1 no LVDS1 | 1.8V | |
| 63 | MIPI_CSI_RX1_D0
N |
Cuir a-steach MIPI CSI1 no LVDS1 | 1.8V | |
| 64 | SDMMC0_D3_3V3 | UART3_TX_M1 | GPIO1_A7_u | 3.3V |
| 65 | SDMMC0_D2_3V3 | UART3_RX_M1 | GPIO1_A6_u | 3.3V |
| 66 | SDMMC0_D1_3V3 | UART2_TX_M0 | GPIO1_A5_u | 3.3V |
| 67 | SDMMC0_D0_3V3 | UART2_RX_M0 | GPIO1_A4_u | 3.3V |
| 68 | SDMMC0_CMD_3V
3 |
UART3_CTSn_M1 | GPIO1_B1_u | 3.3V |
| 69 | SDMMC0_CLK_3V3 | UART3_RTSn_M1 | GPIO1_B0_u | 3.3V |
| 70 | GND | Talamh | 0V | |
| 71 | LED1/CFG_LDO0 | Ethernet LINK LED | 3.3V | |
| 72 | LED2/CFG_LDO1 | Ethernet SPEED LED | 3.3V | |
| 73 | MDI0 + | Comharra MDI Ethernet | 1.8V | |
| 74 | MDI0- | Comharra MDI Ethernet | 1.8V | |
| 75 | MDI1 + | Comharra MDI Ethernet | 1.8V | |
| 76 | MDI1- | Comharra MDI Ethernet | 1.8V | |
| 77 | MDI2 + | Comharra MDI Ethernet | 1.8V | |
| 78 | MDI2- | Comharra MDI Ethernet | 1.8V | |
| 79 | MDI3 + | Comharra MDI Ethernet | 1.8V | |
| 80 | MDI3- | Comharra MDI Ethernet | 1.8V | |
| 81 | I2C1_SCL | UART4_CTSn_M2 | GPIO1_D3_u | 1.8V |
| Pinn | Comharradh | Tuairisgeul no gnìomhan | Sreath GPIO | IO Voltage |
| 82 | I2C1_SDA | UART4_RTSn_M2 | GPIO1_D2_u | 1.8V |
| 83 | MIPI_CSI_PWDN0 | UART4_RX_M2 | GPIO1_D4_d | 1.8V |
| 84 | SPI0_CLK_M1 | I2S1_SDO_M1/UART5_RX_M2 | GPIO2_A1_d | 1.8V |
| 85 | SPI0_MOSI_M1 | I2S1_SCK_M1/I2C3_SCL_M2 | GPIO1_D6_d | 1.8V |
| 86 | SPI0_CS0n_M1 | I2S1_SDI_M1/UART5_TX_M2 | GPIO2_A0_d | 1.8V |
| 87 | SPI0_MISO_M1 | I2S1_LRCK_M1/I2C3_SDA_M2 | GPIO1_D7_d | 1.8V |
| 88 | MIPI_CSI_CLK1 | UART5_RTSn_M2 | GPIO2_A2_d | 1.8V |
| 89 | MIPI_CSI_CLK0 | UART5_CTSn_M2 | GPIO2_A3_d | 1.8V |
| 90 | GND | Talamh | 0V | |
| 91 | LCDC_D0_3V3 | UART4_RTSn_M1/CIF_D0_M1 | GPIO2_A4_d | 3.3V |
| 92 | LCDC_D1_3V3 | UART4_CTSn_M1/CIF_D1_M1 | GPIO2_A5_d | 3.3V |
| 93 | LCDC_D2_3V3 | UART4_TX_M1/CIF_D2_M1 | GPIO2_A6_d | 3.3V |
| 94 | LCDC_D3_3V3 | UART4_RX_M1/I2S2_SDO_M1 | GPIO2_A7_d | 3.3V |
| 95 | LCDC_D4_3V3 | UART5_TX_M1/I2S2_SDI_M1 | GPIO2_B0_d | 3.3V |
| 96 | LCDC_D5_3V3 | UART5_RX_M1/I2S2_SCK_M1 | GPIO2_B1_d | 3.3V |
| 97 | LCDC_D6_3V3 | UART5_RTSn_M1/I2S2_LRCK_
M1 |
GPIO2_B2_d | 3.3V |
| 98 | LCDC_D7_3V3 | UART5_CTSn_M1/I2S2_MCLK_
M1/CIF_D3_M1 |
GPIO2_B3_d | 3.3V |
| 99 | CAN_RX_3V3 | UART3_TX_M2/I2C4_SCL_M0 | GPIO3_A0_u | 3.3V |
| 100 | CAN_TX_3V3 | UART3_RX_M2/I2C4_SDA_M0 | GPIO3_A1_u | 3.3V |
| 101 | LCDC_CLK_3V3 | UART3_CTSn_M2/SPI1_MISO_
M2/PWM8_M1 |
GPIO2_D7_d | 3.3V |
| 102 | LCDC_VSYNC_3V3 | UART3_RTSn_M2/SPI1_MOSI | GPIO2_D6_d | 3.3V |
| 103 | MIPI_DSI_D2P | 1.8V | ||
| 104 | MIPI_DSI_D2N | 1.8V | ||
| 105 | MIPI_DSI_D1P | 1.8V | ||
| 106 | MIPI_DSI_D1N | 1.8V | ||
| 107 | MIPI_DSI_D0P | 1.8V | ||
| 108 | MIPI_DSI_D0N | 1.8V | ||
| 109 | MIPI_DSI_D3P | 1.8V | ||
| 110 | MIPI_DSI_D3N | 1.8V | ||
| 111 | MIPI_DSI_CLKP | 1.8V | ||
| 112 | MIPI_DSI_CLKN | 1.8V | ||
| 113 | ADCIN3 | Cuir a-steach ADC | 1.8V | |
| 114 | ADCIN2 | Cuir a-steach ADC | 1.8V | |
| 115 | ADCIN1 | Cuir a-steach ADC | 1.8V | |
| 116 | ADKEY_IN0 | Seata modh ath-bheothachaidh (10K PU) | 1.8V | |
| 117 | GND | Talamh | 0V | |
| 118 | SDIO_CLK | GPIO1_B2_d | 3.3V (V2) | |
| 119 | SDIO_CMD | GPIO1_B3_u | 3.3V (V2) |
| Pinn | Comharradh | Tuairisgeul no gnìomhan | Sreath GPIO | IO Voltage |
| 120 | SDIO_D0 | GPIO1_B4_u | 3.3V (V2) | |
| 121 | SDIO_D1 | GPIO1_B5_u | 3.3V (V2) | |
| 122 | SDIO_D2 | GPIO1_B6_u | 3.3V (V2) | |
| 123 | SDIO_D3 | GPIO1_B7_u | 3.3V (V2) | |
| 124 | UART0_RX | GPIO1_C2_u | 3.3V (V2) | |
| 125 | UART0_TX | GPIO1_C3_u | 3.3V (V2) | |
| 126 | UART0_CTSN | GPIO1_C1_u | 3.3V (V2) | |
| 127 | UART0_RTSN | GPIO1_C0_u | 3.3V (V2) | |
| 128 | PCM_TX | I2S2_SDO_M0/SPI1_MOSI_M1 | GPIO1_C4_d | 3.3V (V2) |
| 129 | PCM_SYNC | I2S2_LRCK_M0/SPI1_CSn0_M
1/UART1_CTSn_M1 |
GPIO1_C7_d | 3.3V (V2) |
| 130 | PCM_CLK | I2S2_SCLK_M0/SPI1_CLK_M1/
UART1_RTSn_M1 |
GPIO1_C6_d | 3.3V (V2) |
| 131 | PCM_RX | I2S2_SDI_M0/SPI1_MISO_M1 | GPIO1_C5_d | 3.3V (V2) |
| 132 | LCDC_D15_3V3 | CIF_D11_M1 | GPIO2_C3_d | 3.3V |
| 133 | LCDC_D14_3V3 | CIF_D10_M1 | GPIO2_C2_d | 3.3V |
| 134 | LCDC_D13_3V3 | CIF_D9_M1 | GPIO2_C1_d | 3.3V |
| 135 | LCDC_D12_3V3 | CIF_D8_M1 | GPIO2_C0_d | 3.3V |
| 136 | LCDC_DEN_3V3 | I2C3_SCL_M1/SPI1_CS0n_M2 | GPIO2_D4_d | 3.3V |
| 137 | LCDC_D10_3V3 | CIF_D6_M1 | GPIO2_B6_d | 3.3V |
| 138 | LCDC_D9_3V3 | CIF_D5_M1 | GPIO2_B5_d | 3.3V |
| 139 | LCDC_D8_3V3 | CIF_D4_M1 | GPIO2_B4_d | 3.3V |
| 140 | LCDC_D11_3V3 | CIF_D7_M1 | GPIO2_B7_d | 3.3V |
| 141 | LCDC_HSYNC_3V3 | I2C3_SDA_M1/SPI1_CLK_M2 | GPIO2_D5_d | 3.3V |
| 142 | LCDC_D16_3V3 | CIF_D12_M1 | GPIO2_C4_d | 3.3V |
| 143 | LCDC_D17_3V3 | CIF_D13_M1 | GPIO2_C5_d | 3.3V |
| 144 | LCDC_D18_3V3 | CIF_D14_M1 | GPIO2_C6_d | 3.3V |
| Thoir an aire:
1. Tha a’ mhòr-chuid de GPIO voltagTha e 1.8V, ach tha cuid de phrìneachan air an comharrachadh 3.3V. 2. GPIO voltagatharrachadh gu 3.3V airson comharraichte (V2). |
||||
Pasgan Leasachaidh (Idea1126)
Stiùireadh Dealbhadh Bathar-cruaidh
Iomradh cuairte iomaill
Prìomh Chuairt-cumhachd
Circuit Debug
Cearcall eadar-aghaidh USB OTG
Lorg-coise PCB
Feartan dealain toraidh
Dissipation agus Teòthachd
| samhladh | Paramadair | Min | Taidhp | Max | Aonad |
| VCC3V3_SYS | Siostam IO
Voltage |
3.3-5% | 3.3 | 3.3 + 5% | V |
| Isys_in | Cuir a-steach VCC3V3_SYS An-dràsta | 850 | mA | ||
| Ta | Teòthachd Obrachaidh | -20 | 70 | °C | |
| Tstg | Teòthachd stòraidh | -40 | 85 | °C |
Dleastanas na deuchainn
| Deuchainn Obrachaidh Teòthachd Àrd | ||
| Clàr-innse | Operating 8h in high temperatures | 55 ° C ± 2 ° C. |
| Toradh | TBD |
| Deuchainn beatha obrachaidh | ||
| Clàr-innse | Operating in the room | 120 h |
| Toradh | TBD |
Barantas cuibhrichte
Boardcon warrants this product to be free of defects in material and workmanship for one year from the date of purchase. During this warranty period, Boardcon will repair or replace the defective unit by the following process: A copy of the original invoice must be included when returning the defective unit to Boardcon. This limited warranty does not cover damages resulting from lightning or other power surges, misuse, abuse, abnormal conditions of operation, or attempts to alter or modify the function of the product. This warranty is limited to the repair or replacement of the defective unit. In no event shall Boardcon be liable or responsible for any loss or damages, including but not limited to any lost profits, incidental or consequential damages, loss of business, or anticipatory profits arising from the use or inability to use this product. Repairs made after the expiration of the warranty period are subject to a repair charge and the cost of return shipping. Please contact Boardcon to arrange for any repair service and to obtain repair charge information.
Ceistean Cumanta
C: Ciamar a nì mi ùrachadh air cuimhne DDR air CM1126B-P?
A: The CM1126B-P supports up to 4GB LPDDR4 memory. To upgrade, ensure compatibility with the specifications and follow recommended procedures.
C: Dè an riatanas solar cumhachd a th’ ann airson CM1126B-P?
A: The power requirement for CM1126B-P is DC 3.3V. Ensure to provide a stable power supply within this range for optimal performance.
C: An urrainn dhomh comas stòraidh eMMC a leudachadh air CM1126B-P?
A: Yes, the eMMC storage on CM1126B-P can be expanded up to 256GB. Ensure compatibility with supported storage devices before upgrading.
Sgrìobhainnean/Goireasan
 |
Siostam CM1126B-P leabaithe Boardcon air Modúl [pdfLeabhar-làimhe an neach-cleachdaidh V2.20250422, Siostam CM1126B-P air Modúl, CM1126B-P, Siostam air Modúl, Modúl |