Boardcon ifibọ CM1126B-P System on Module
Awọn pato
| Ẹya ara ẹrọ | Awọn pato |
| Sipiyu | Quad-mojuto kotesi-A53 |
| DDR | 2GB LPDDR4 (to 4GB) |
| eMMC FLASH | 8GB (to 256GB) |
| Agbara | DC 3.3V |
| MIPI DSI | 4-Lane |
| I2S | 4-CH |
| MIPI CSI | 2-CH 4-Lane |
| RGB LCD | 24bit |
| Kamẹra | 1-CH (DVP) ati 2-CH (CSI) |
| USB | 2-CH (USB HOST 2.0 ati OTG 2.0) |
| Àjọlò | 1000M GMAC |
| SDMMC | 2-CH |
| I2C | 5-CH |
| SPI | 2-CH |
| UART | 5-CH, 1-CH (DEBUG) |
| PWM | 11-CH |
| ADC IN | 4-CH |
| Board Dimension | 34 x 35mm |
Ọrọ Iṣaaju
Nipa Itọsọna yii
Iwe afọwọkọ yii jẹ ipinnu lati pese olumulo pẹlu ipariview ti igbimọ ati awọn anfani rẹ, awọn ẹya ara ẹrọ pipe, ati awọn ilana iṣeto. O ni alaye ailewu pataki bi daradara.
Esi ati Imudojuiwọn si Itọsọna yii
Lati ṣe iranlọwọ fun awọn alabara wa lati lo pupọ julọ awọn ọja wa, a n ṣe nigbagbogbo ni afikun ati awọn orisun imudojuiwọn wa lori Boardcon webAaye (www.boardcon.com, www.armdesigner.com). Iwọnyi pẹlu awọn iwe ilana, awọn akọsilẹ ohun elo, siseto examples, ati imudojuiwọn software ati hardware. Ṣayẹwo lorekore lati rii kini tuntun! Nigba ti a ba n ṣe pataki iṣẹ lori awọn orisun imudojuiwọn wọnyi, esi lati ọdọ awọn alabara ni ipa akọkọ, Ti o ba ni awọn ibeere, awọn asọye, tabi awọn ifiyesi nipa ọja tabi iṣẹ akanṣe, jọwọ ma ṣe ṣiyemeji lati kan si wa ni support@armdesigner.com.
CM1126B-P Ifihan
Lakotan
CM1126B-P eto-on-module ti ni ipese pẹlu Rockchip's RV1126B-P, ti a ṣe pẹlu quad-core Cortex-A53, 3.0 TOPs NPU, ati RISC-V MCU. O jẹ apẹrẹ pataki fun awọn ẹrọ IPC/CVR, awọn ẹrọ kamẹra AI, awọn ẹrọ ibaraenisepo oye, ati awọn roboti mini. Iṣe-giga ati awọn solusan agbara-kekere le ṣe iranlọwọ fun awọn alabara lati ṣafihan awọn imọ-ẹrọ tuntun diẹ sii ni iyara ati mu imudara ojutu apapọ pọ si. Iwọn ti o kere julọ ni a le fi si ori 38board. Ni atẹle atunyẹwo ohun elo lati CM1126 (V1) si CM1126B-P (V2), nibiti SoC ti ni imudojuiwọn si RV1126B-P, awọn ifihan agbara Tun & OTG_VBUS ati WIFI/BT module's GPIO voltage gbọdọ ṣiṣẹ ni ipele kannaa 3.3V.
Awọn ẹya ara ẹrọ
Microprocessor
- Quad-core Cortex-A53 to 1.6GHz
- 32KB I-cache ati 32KB D-cache fun mojuto kọọkan, 512KB L3 kaṣe
- 3.0 TOP nkankikan ilana Unit
- RISC-V MCU lati ṣe atilẹyin bata iyara 250ms
- Iye ti o ga julọ ti 12M
Ajo Iranti
- LPDDR4 Ramu soke si 4GB
- eMMC to 256GB
- SPI Flash to 8MB
Video Decoder/Epo koodu
- Ṣe atilẹyin iyipada fidio / koodu to 4K@30fps
- Ṣe atilẹyin iyipada akoko gidi ti H.264/265
- Ṣe atilẹyin fun akoko gidi UHD H.264/265 fifi koodu fidio
- Iwọn aworan to 8192×8192
Ifihan Subsystem
- Ijade fidio
- Ṣe atilẹyin awọn ọna 4 MIPI DSI to 2560×1440@60fps
- Ṣe atilẹyin iṣẹjade afiwera 24-bit RGB
- Aworan ninu
- Atilẹyin soke to 16-bit DVP ni wiwo
- Ṣe atilẹyin 2ch MIPI CSI 4lanes ni wiwo
I2S/PCM/ AC97
- Mẹta I2S / PCM ni wiwo
- Ṣe atilẹyin orun Gbohungbohun Titi di wiwo 8ch PDM/TDM
- Ṣe atilẹyin iṣẹjade ohun afetigbọ PWM
USB ati PCIE
- Meji 2.0 USB atọkun
- Ọkan USB 2.0 OTG ati ọkan 2.0 USB ogun
Àjọlò
- RTL8211F lori ọkọ
- Atilẹyin 10/100/1000M
I2C
- Titi di awọn I2C marun
- Ṣe atilẹyin ipo boṣewa ati ipo iyara (to 400kbit / s)
SDIO
- Atilẹyin 2CH SDIO 3.0 Ilana
SPI
- Titi di awọn oludari SPI meji,
- Full-ile oloke meji amuṣiṣẹpọ ni tẹlentẹle ni wiwo
UART
- Ṣe atilẹyin fun awọn UART 6
- UART2 pẹlu 2 onirin fun yokokoro irinṣẹ
- Ifibọ meji 664-baiti FIFOs
- Ṣe atilẹyin ipo iṣakoso ṣiṣan aifọwọyi fun UART0/1/3/4/5
ADC
- Titi di awọn ikanni ADC mẹrin
- 12-bit ipinnu
- Voltage input ibiti laarin 0V to 1.8V
- Ṣe atilẹyin to 1MS/ssampoṣuwọn ling
PWM
- 11 lori-chip PWM pẹlu iṣẹ ti o da lori idalọwọduro
- Ṣe atilẹyin akoko 32-bit / ohun elo counter
- Aṣayan IR lori PWM3/7
Ẹka agbara
- Oye Agbara lori ọkọ
- Nikan 3.3V igbewọle
CM1126B-P Block aworan atọka
RV1126B-P Block aworan atọka
Development ọkọ (Idea1126) Àkọsílẹ aworan atọka
CM1126B-P PCB Dimension
CM1126B-P Pin Definition
| Pin | Ifihan agbara | Apejuwe tabi awọn iṣẹ | GPIO ni tẹlentẹle | IO Voltage |
| 1 | LCDC_D19_3V3 | I2S1_MCLK_M2/CIF_D15_M1 | GPIO2_C7_d | 3.3V |
| 2 | LCDC_D20_3V3 | I2S1_SDO_M2 / CIF_VS_M1 | GPIO2_D0_d | 3.3V |
| 3 | LCDC_D21_3V3 | I2S1_SCLK_M2 / CIF_CLKO_M1 | GPIO2_D1_d | 3.3V |
| 4 | LCDC_D22_3V3 | I2S1_LRCK_M2 / CIF_CKIN_M1 | GPIO2_D2_d | 3.3V |
| 5 | LCDC_D23_3V3 | I2S1_SDI_M2 / CIF_HS_M1 | GPIO2_D3_d | 3.3V |
| 6 | GND | Ilẹ | 0V | |
| 7 | GPIO1_D1 | UART1_RX_M1/I2C5_SDA_M2 | GPIO1_D1_d | 3.3V(V2) |
| 8 | BT_WAKE | SPI0_CS1n_M0 | GPIO0_A4_u | 3.3V(V2) |
| 9 | WIFI_REG_ON | SPI0_MOSI_M0 | GPIO0_A6_d | 3.3V(V2) |
| 10 | BT_RST | SPI0_MISO_M0 | GPIO0_A7_d | 3.3V(V2) |
| 11 | WIFI_WAKE_HOST | SPI0_CLK_M0 | GPIO0_B0_d | 3.3V(V2) |
| 12 | BT_WAKE_HOST | SPI0_CS0n_M0 | GPIO0_A5_u | 3.3V(V2) |
| 13 | PWM7_IR_M0_3V3 | GPIO0_B1_d | 3.3V | |
| 14 | PWM6_M0_3V3 | TSADC_SHUT_M1 | GPIO0_B2_d | 3.3V |
| 15 | UART2_TX_3V3 | Fun yokokoro | GPIO3_A2_u | 3.3V |
| 16 | UART2_RX_3V3 | Fun yokokoro | GPIO3_A3_u | 3.3V |
| 17 | I2S0_MCLK_M0_3V
3 |
GPIO3_D2_d | 3.3V | |
| 18 | I2S0_SCLK_TX_M0
_3V3 |
ACODEC_DAC_CLK | GPIO3_D0_d | 3.3V |
| 19 | I2S0_SDI3_M0_3V3 | PDM_SDI3_M0 /
ACODEC_ADC_DATA |
GPIO3_D7_d | 3.3V |
| 20 | I2S0_SDO0_M0_3V
3 |
ACODEC_DAC_DATAR
/APWM_R_M1/ADSM_LP |
GPIO3_D5_d | 3.3V |
| Pin | Ifihan agbara | Apejuwe tabi awọn iṣẹ | GPIO ni tẹlentẹle | IO Voltage |
| 21 | I2S0_LRCK_TX_M0
_3V3 |
ACODEC_DAC_SYNC
/APWM_L_M1/ADSM_LN |
GPIO3_D3_d | 3.3V |
| 22 | PDM_SDI1_3V3 | I2S0_SDO3_SDI1_M0/I2C4SDA | GPIO4_A1_d | 3.3V |
| 23 | PDM_CLK1_3V3 | I2S0_SCK_RX_M0 | GPIO3_D1_d | 3.3V |
| 24 | PDM_SDI2_3V3 | I2S0_SDO2_SDI2_M0/I2C4SCL | GPIO4_A0_d | 3.3V |
| 25 | PDM_SDI0_3V3 | I2S0_SDI0_M0 | GPIO3_D6_d | 3.3V |
| 26 | PDM_CLK_3V3 | I2S0_LRCK_RX_M0 | GPIO3_D4_d | 3.3V |
| 27 | I2C2_SDA_3V3 | PWM5_M0 | GPIO0_C3_d | 3.3V |
| 28 | I2C2_SCL_3V3 | PWM4_M0 | GPIO0_C2_d | 3.3V |
| 29 | USB_HOST_DP | 1.8V | ||
| 30 | USB_HOST_DM | 1.8V | ||
| 31 | GND | Ilẹ | 0V | |
| 32 | OTG_DP | Le ṣee lo fun download | 1.8V | |
| 33 | OTG_DM | Le ṣee lo fun download | 1.8V | |
| 34 | OTG_DET(V2) | OTG VBUS DET IN | 3.3V(V2) | |
| 35 | OTG_ID | 1.8V | ||
| 36 | SPI0_CS1n_M1 | I2S1_MCK_M1/UART4_TX_M2 | GPIO1_D5_d | 1.8V |
| 37 | VCC3V3_SYS | 3.3V Main Power input | 3.3V | |
| 38 | VCC3V3_SYS | 3.3V Main Power input | 3.3V | |
| 39 | USB_CTRL_3V3 | GPIO0_C1_d | 3.3V | |
| 40 | SDMMC0_DET | Gbọdọ ṣee lo fun kaadi SD | GPIO0_A3_u | 3.3V(V2) |
| 41 | CLKO_32K | RTC aago jade | GPIO0_A2_u | 3.3V(V2) |
| 42 | n RESET | Tun titẹ bọtini atunto | 3.3V(V2) | |
| 43 | MIPI_CSI_RX0_CL
KP |
MIPI CSI0 tabi LVDS0 igbewọle | 1.8V | |
| 44 | MIPI_CSI_RX0_CL
KN |
MIPI CSI0 tabi LVDS0 igbewọle | 1.8V | |
| 45 | MIPI_CSI_RX0_D2
P |
MIPI CSI0 tabi LVDS0 igbewọle | 1.8V | |
| 46 | MIPI_CSI_RX0_D2
N |
MIPI CSI0 tabi LVDS0 igbewọle | 1.8V | |
| 47 | MIPI_CSI_RX0_D3
P |
MIPI CSI0 tabi LVDS0 igbewọle | 1.8V | |
| 48 | MIPI_CSI_RX0_D3
N |
MIPI CSI0 tabi LVDS0 igbewọle | 1.8V | |
| 49 | MIPI_CSI_RX0_D1
P |
MIPI CSI0 tabi LVDS0 igbewọle | 1.8V | |
| 50 | MIPI_CSI_RX0_D1
N |
MIPI CSI0 tabi LVDS0 igbewọle | 1.8V | |
| 51 | MIPI_CSI_RX0_D0
P |
MIPI CSI0 tabi LVDS0 igbewọle | 1.8V |
| Pin | Ifihan agbara | Apejuwe tabi awọn iṣẹ | GPIO ni tẹlentẹle | IO Voltage |
| 52 | MIPI_CSI_RX0_D0
N |
MIPI CSI0 tabi LVDS0 igbewọle | 1.8V | |
| 53 | GND | Ilẹ | 0V | |
| 54 | MIPI_CSI_RX1_D3
P |
MIPI CSI1 tabi LVDS1 igbewọle | 1.8V | |
| 55 | MIPI_CSI_RX1_D3
N |
MIPI CSI1 tabi LVDS1 igbewọle | 1.8V | |
| 56 | MIPI_CSI_RX1_CL
KP |
MIPI CSI1 tabi LVDS1 igbewọle | 1.8V | |
| 57 | MIPI_CSI_RX1_CL
KN |
MIPI CSI1 tabi LVDS1 igbewọle | 1.8V | |
| 58 | MIPI_CSI_RX1_D2
P |
MIPI CSI1 tabi LVDS1 igbewọle | 1.8V | |
| 59 | MIPI_CSI_RX1_D2
N |
MIPI CSI1 tabi LVDS1 igbewọle | 1.8V | |
| 60 | MIPI_CSI_RX1_D1
P |
MIPI CSI1 tabi LVDS1 igbewọle | 1.8V | |
| 61 | MIPI_CSI_RX1_D1
N |
MIPI CSI1 tabi LVDS1 igbewọle | 1.8V | |
| 62 | MIPI_CSI_RX1_D0
P |
MIPI CSI1 tabi LVDS1 igbewọle | 1.8V | |
| 63 | MIPI_CSI_RX1_D0
N |
MIPI CSI1 tabi LVDS1 igbewọle | 1.8V | |
| 64 | SDMMC0_D3_3V3 | UART3_TX_M1 | GPIO1_A7_u | 3.3V |
| 65 | SDMMC0_D2_3V3 | UART3_RX_M1 | GPIO1_A6_u | 3.3V |
| 66 | SDMMC0_D1_3V3 | UART2_TX_M0 | GPIO1_A5_u | 3.3V |
| 67 | SDMMC0_D0_3V3 | UART2_RX_M0 | GPIO1_A4_u | 3.3V |
| 68 | SDMMC0_CMD_3V
3 |
UART3_CTSn_M1 | GPIO1_B1_u | 3.3V |
| 69 | SDMMC0_CLK_3V3 | UART3_RTSn_M1 | GPIO1_B0_u | 3.3V |
| 70 | GND | Ilẹ | 0V | |
| 71 | LED1 / CFG_LDO0 | Àjọlò RÁNṢẸ LED | 3.3V | |
| 72 | LED2 / CFG_LDO1 | Àjọlò SPEED LED | 3.3V | |
| 73 | MDI0 + | Àjọlò MDI ifihan agbara | 1.8V | |
| 74 | MDI0- | Àjọlò MDI ifihan agbara | 1.8V | |
| 75 | MDI1 + | Àjọlò MDI ifihan agbara | 1.8V | |
| 76 | MDI1- | Àjọlò MDI ifihan agbara | 1.8V | |
| 77 | MDI2 + | Àjọlò MDI ifihan agbara | 1.8V | |
| 78 | MDI2- | Àjọlò MDI ifihan agbara | 1.8V | |
| 79 | MDI3 + | Àjọlò MDI ifihan agbara | 1.8V | |
| 80 | MDI3- | Àjọlò MDI ifihan agbara | 1.8V | |
| 81 | I2C1_SCL | UART4_CTSn_M2 | GPIO1_D3_u | 1.8V |
| Pin | Ifihan agbara | Apejuwe tabi awọn iṣẹ | GPIO ni tẹlentẹle | IO Voltage |
| 82 | I2C1_SDA | UART4_RTSn_M2 | GPIO1_D2_u | 1.8V |
| 83 | MIPI_CSI_PWDN0 | UART4_RX_M2 | GPIO1_D4_d | 1.8V |
| 84 | SPI0_CLK_M1 | I2S1_SDO_M1/UART5_RX_M2 | GPIO2_A1_d | 1.8V |
| 85 | SPI0_MOSI_M1 | I2S1_SCK_M1/I2C3_SCL_M2 | GPIO1_D6_d | 1.8V |
| 86 | SPI0_CS0n_M1 | I2S1_SDI_M1/UART5_TX_M2 | GPIO2_A0_d | 1.8V |
| 87 | SPI0_MISO_M1 | I2S1_LRCK_M1/I2C3_SDA_M2 | GPIO1_D7_d | 1.8V |
| 88 | MIPI_CSI_CLK1 | UART5_RTSn_M2 | GPIO2_A2_d | 1.8V |
| 89 | MIPI_CSI_CLK0 | UART5_CTSn_M2 | GPIO2_A3_d | 1.8V |
| 90 | GND | Ilẹ | 0V | |
| 91 | LCDC_D0_3V3 | UART4_RTSn_M1 / CIF_D0_M1 | GPIO2_A4_d | 3.3V |
| 92 | LCDC_D1_3V3 | UART4_CTSn_M1 / CIF_D1_M1 | GPIO2_A5_d | 3.3V |
| 93 | LCDC_D2_3V3 | UART4_TX_M1 / CIF_D2_M1 | GPIO2_A6_d | 3.3V |
| 94 | LCDC_D3_3V3 | UART4_RX_M1/I2S2_SDO_M1 | GPIO2_A7_d | 3.3V |
| 95 | LCDC_D4_3V3 | UART5_TX_M1/I2S2_SDI_M1 | GPIO2_B0_d | 3.3V |
| 96 | LCDC_D5_3V3 | UART5_RX_M1/I2S2_SCK_M1 | GPIO2_B1_d | 3.3V |
| 97 | LCDC_D6_3V3 | UART5_RTSn_M1/I2S2_LRCK_
M1 |
GPIO2_B2_d | 3.3V |
| 98 | LCDC_D7_3V3 | UART5_CTSn_M1/I2S2_MCLK_
M1 / CIF_D3_M1 |
GPIO2_B3_d | 3.3V |
| 99 | CAN_RX_3V3 | UART3_TX_M2/I2C4_SCL_M0 | GPIO3_A0_u | 3.3V |
| 100 | CAN_TX_3V3 | UART3_RX_M2/I2C4_SDA_M0 | GPIO3_A1_u | 3.3V |
| 101 | LCDC_CLK_3V3 | UART3_CTSn_M2/SPI1_MISO_
M2/PWM8_M1 |
GPIO2_D7_d | 3.3V |
| 102 | LCDC_VSYNC_3V3 | UART3_RTSn_M2 / SPI1_MOSI | GPIO2_D6_d | 3.3V |
| 103 | MIPI_DSI_D2P | 1.8V | ||
| 104 | MIPI_DSI_D2N | 1.8V | ||
| 105 | MIPI_DSI_D1P | 1.8V | ||
| 106 | MIPI_DSI_D1N | 1.8V | ||
| 107 | MIPI_DSI_D0P | 1.8V | ||
| 108 | MIPI_DSI_D0N | 1.8V | ||
| 109 | MIPI_DSI_D3P | 1.8V | ||
| 110 | MIPI_DSI_D3N | 1.8V | ||
| 111 | MIPI_DSI_CLKP | 1.8V | ||
| 112 | MIPI_DSI_CLKN | 1.8V | ||
| 113 | ADCI3 | ADC igbewọle | 1.8V | |
| 114 | ADCI2 | ADC igbewọle | 1.8V | |
| 115 | ADCI1 | ADC igbewọle | 1.8V | |
| 116 | ADKEY_IN0 | Eto ipo imularada(10K PU) | 1.8V | |
| 117 | GND | Ilẹ | 0V | |
| 118 | SDIO_CLK | GPIO1_B2_d | 3.3V(V2) | |
| 119 | SDIO_CMD | GPIO1_B3_u | 3.3V(V2) |
| Pin | Ifihan agbara | Apejuwe tabi awọn iṣẹ | GPIO ni tẹlentẹle | IO Voltage |
| 120 | SDIO_D0 | GPIO1_B4_u | 3.3V(V2) | |
| 121 | SDIO_D1 | GPIO1_B5_u | 3.3V(V2) | |
| 122 | SDIO_D2 | GPIO1_B6_u | 3.3V(V2) | |
| 123 | SDIO_D3 | GPIO1_B7_u | 3.3V(V2) | |
| 124 | UART0_RX | GPIO1_C2_u | 3.3V(V2) | |
| 125 | UART0_TX | GPIO1_C3_u | 3.3V(V2) | |
| 126 | UART0_CTSN | GPIO1_C1_u | 3.3V(V2) | |
| 127 | UART0_RTSN | GPIO1_C0_u | 3.3V(V2) | |
| 128 | PCM_TX | I2S2_SDO_M0/SPI1_MOSI_M1 | GPIO1_C4_d | 3.3V(V2) |
| 129 | PCM_SYNC | I2S2_LRCK_M0/SPI1_CSn0_M
1/UART1_CTSn_M1 |
GPIO1_C7_d | 3.3V(V2) |
| 130 | PCM_CLK | I2S2_SCLK_M0/SPI1_CLK_M1/
UART1_RTSn_M1 |
GPIO1_C6_d | 3.3V(V2) |
| 131 | PCM_RX | I2S2_SDI_M0/SPI1_MISO_M1 | GPIO1_C5_d | 3.3V(V2) |
| 132 | LCDC_D15_3V3 | CIF_D11_M1 | GPIO2_C3_d | 3.3V |
| 133 | LCDC_D14_3V3 | CIF_D10_M1 | GPIO2_C2_d | 3.3V |
| 134 | LCDC_D13_3V3 | CIF_D9_M1 | GPIO2_C1_d | 3.3V |
| 135 | LCDC_D12_3V3 | CIF_D8_M1 | GPIO2_C0_d | 3.3V |
| 136 | LCDC_DEN_3V3 | I2C3_SCL_M1/SPI1_CS0n_M2 | GPIO2_D4_d | 3.3V |
| 137 | LCDC_D10_3V3 | CIF_D6_M1 | GPIO2_B6_d | 3.3V |
| 138 | LCDC_D9_3V3 | CIF_D5_M1 | GPIO2_B5_d | 3.3V |
| 139 | LCDC_D8_3V3 | CIF_D4_M1 | GPIO2_B4_d | 3.3V |
| 140 | LCDC_D11_3V3 | CIF_D7_M1 | GPIO2_B7_d | 3.3V |
| 141 | LCDC_HSYNC_3V3 | I2C3_SDA_M1/SPI1_CLK_M2 | GPIO2_D5_d | 3.3V |
| 142 | LCDC_D16_3V3 | CIF_D12_M1 | GPIO2_C4_d | 3.3V |
| 143 | LCDC_D17_3V3 | CIF_D13_M1 | GPIO2_C5_d | 3.3V |
| 144 | LCDC_D18_3V3 | CIF_D14_M1 | GPIO2_C6_d | 3.3V |
| Akiyesi:
1. Julọ GPIO voltage jẹ 1.8V, ṣugbọn diẹ ninu awọn pinni samisi 3.3V. 2. GPIO voltage yipada si 3.3V fun samisi (V2). |
||||
Ohun elo Idagbasoke (Idea1126)
Hardware Design Itọsọna
Agbeegbe Circuit Reference
Main Power Circuit
yokokoro Circuit
USB OTG Interface Circuit
PCB Ẹsẹ
Ọja Electrical Abuda
Pipa ati Iwọn otutu
| Aami | Paramita | Min | Iru | O pọju | Ẹyọ |
| VCC3V3_SYS | Eto IO
Voltage |
3.3-5% | 3.3 | 3.3 + 5% | V |
| Isys_in | VCC3V3_SYS input Lọwọlọwọ | 850 | mA | ||
| Ta | Awọn iwọn otutu ti nṣiṣẹ | -20 | 70 | °C | |
| Tstg | Ibi ipamọ otutu | -40 | 85 | °C |
Igbẹkẹle ti Idanwo
| Igbeyewo Iṣiṣẹ Iwọn otutu giga | ||
| Awọn akoonu | Ṣiṣẹ 8h ni awọn iwọn otutu giga | 55 ° C ± 2 ° C |
| Abajade | TBD |
| Igbeyewo Igbesi aye Ṣiṣẹ | ||
| Awọn akoonu | Ṣiṣẹ ninu yara naa | 120h |
| Abajade | TBD |
Atilẹyin ọja to lopin
Boardcon ṣe atilẹyin ọja yii lati ni abawọn ninu ohun elo ati iṣẹ-ṣiṣe fun ọdun kan lati ọjọ rira. Nigba akoko atilẹyin ọja, Boardcon yoo tun tabi ropo awọn alebu awọn kuro nipa awọn ilana: A daakọ ti awọn atilẹba risiti gbọdọ wa ni o wa nigba ti o ba da awọn alebu awọn kuro to Boardcon. Atilẹyin ọja to lopin ko ni aabo awọn bibajẹ ti o waye lati inu manamana tabi jiji agbara miiran, ilokulo, ilokulo, awọn ipo aiṣiṣẹ, tabi awọn igbiyanju lati paarọ tabi yipada iṣẹ ọja naa. Atilẹyin ọja yi wa ni opin si titunṣe tabi rirọpo ti awọn alebu awọn kuro. Ko si iṣẹlẹ ti Boardcon yoo ṣe oniduro tabi ṣe oniduro fun eyikeyi pipadanu tabi bibajẹ, pẹlu ṣugbọn kii ṣe opin si eyikeyi awọn ere ti o sọnu, isẹlẹ tabi awọn bibajẹ ti o wulo, ipadanu iṣowo, tabi awọn ere ifojusọna ti o dide lati lilo tabi ailagbara lati lo ọja yii. Awọn atunṣe ti a ṣe lẹhin ipari akoko atilẹyin ọja wa labẹ idiyele atunṣe ati idiyele ti gbigbe pada. Jọwọ kan si Boardcon lati ṣeto fun eyikeyi iṣẹ atunṣe ati lati gba alaye idiyele atunṣe.
FAQs
Q: Bawo ni MO ṣe igbesoke iranti DDR lori CM1126B-P?
A: CM1126B-P ṣe atilẹyin to 4GB LPDDR4 iranti. Lati ṣe igbesoke, rii daju ibamu pẹlu awọn pato ati tẹle awọn ilana iṣeduro.
Q: Kini ibeere ipese agbara fun CM1126B-P?
A: Awọn ibeere agbara fun CM1126B-P ni DC 3.3V. Rii daju lati pese ipese agbara iduroṣinṣin laarin iwọn yii fun iṣẹ ṣiṣe to dara julọ.
Q: Ṣe MO le faagun agbara ipamọ ti eMMC lori CM1126B-P?
A: Bẹẹni, ibi ipamọ eMMC lori CM1126B-P le ṣe afikun si 256GB. Rii daju ibamu pẹlu atilẹyin awọn ẹrọ ipamọ ṣaaju iṣagbega.
Awọn iwe aṣẹ / Awọn orisun
 |
Boardcon ifibọ CM1126B-P System on Module [pdf] Afowoyi olumulo V2.20250422, CM1126B-P System on Module, CM1126B-P, Eto lori Module, Module |