Boardcon Embedded CM1126B-P System on Module

ዝርዝሮች

ባህሪ	ዝርዝሮች
ሲፒዩ	ባለአራት ኮር ኮርቴክስ-A53
ዲ.ዲ.ዲ	2GB LPDDR4 (እስከ 4ጂቢ)
eMMC ፍላሽ	8GB (እስከ 256GB)
ኃይል	ዲሲ 3.3 ቪ
MIPI DSI	4-ሌን
አይ 2 ሴ	4-CH
MIPI CSI	2-CH 4-ሌይን
RGB LCD	24 ቢት
ካሜራ	1-CH(DVP) እና 2-CH(CSI)
ዩኤስቢ	2-CH (USB HOST 2.0 and OTG 2.0)
ኤተርኔት	1000M GMAC
ኤስዲኤምኤምሲ	2-CH
I2C	5-CH
SPI	2-CH
UART	5-CH፣ 1-CH(DEBUG)
PWM	11-CH
ADC IN	4-CH
የቦርድ መጠን	34 x 35 ሚሜ

መግቢያ

ስለዚህ መመሪያ
ይህ ማኑዋል ለተጠቃሚው ኦቨር ለማቅረብ የታሰበ ነው።view of the board and its benefits, complete feature specifications, and setup procedures. It contains important safety information as well.

ለዚህ መመሪያ ግብረ መልስ እና ማዘመን
ደንበኞቻችን ምርቶቻችንን በአግባቡ እንዲጠቀሙ ለማገዝ በቦርድኮን ላይ ተጨማሪ እና የተዘመኑ ግብዓቶችን ያለማቋረጥ እያዘጋጀን ነው። webጣቢያ (www.boardcon.com, www.armdesigner.com). እነዚህ ማኑዋሎች፣ የመተግበሪያ ማስታወሻዎች፣ የፕሮግራም አወጣጥ ለምሳሌamples፣ እና የዘመነ ሶፍትዌር እና ሃርድዌር። ምን አዲስ ነገር እንዳለ ለማየት በየጊዜው ይግቡ! በእነዚህ የተሻሻሉ ሀብቶች ላይ ሥራ ቅድሚያ ስንሰጥ፣ የደንበኞች አስተያየት ቁጥር አንድ ተጽዕኖ ነው፣ ስለ ምርትዎ ወይም ፕሮጀክትዎ ጥያቄዎች፣ አስተያየቶች ወይም ስጋቶች ካሉዎት እባክዎን በ ላይ እኛን ለማነጋገር አያመንቱ። support@armdesigner.com.

CM1126B-P Introduction

ማጠቃለያ
The CM1126B-P system-on-module is equipped with Rockchip’s RV1126B-P, built with a quad-core Cortex-A53, 3.0 TOPs NPU, and RISC-V MCU. It is designed specifically for the IPC/CVR devices, AI Camera devices, intelligent interactive devices, and mini robots. High-performance and low-power solutions can help customers introduce new technologies more quickly and enhance the overall solution efficiency. The smallest size can be put on a 38board. Following the hardware revision from CM1126 (V1) to CM1126B-P (V2), where the SoC is updated to the RV1126B-P, the Reset & OTG_VBUS signals and the WIFI/BT module’s GPIO voltage must operate at a 3.3V logic level.

ባህሪያት

ማይክሮፕሮሰሰር

• ባለአራት ኮር ኮርቴክስ-A53 እስከ 1.6GHz
• 32KB I-cache እና 32KB D-cache ለእያንዳንዱ ኮር፣ 512KB L3 መሸጎጫ
• 3.0 ምርጥ የነርቭ ሂደት ክፍል
• RISC-V MCU to support 250ms fast boot
• ከፍተኛው 12M አይኤስፒ

የማህደረ ትውስታ ድርጅት

• LPDDR4 RAM እስከ 4GB
• eMMC እስከ 256GB
• SPI ፍላሽ እስከ 8 ሜባ

ቪዲዮ ዲኮደር/ኢንኮደር

• እስከ 4K@30fps የቪዲዮ ዲኮድ/ኢኮድ ይደግፋል
• የ H.264/265 ቅጽበታዊ ኮድ መፍታትን ይደግፋል
• የእውነተኛ ጊዜ UHD H.264/265 ቪዲዮን ኮድ ማድረግን ይደግፋል
• የምስል መጠን እስከ 8192×8192

የማሳያ ንዑስ ስርዓት

• የቪዲዮ ውፅዓት
  • Supports 4 lanes MIPI DSI up to 2560×1440@60fps
  • Supports 24-bit RGB parallel output
• ምስል በ
  • Supports up to 16-bit DVP interface
  • 2ch MIPI CSI 4lanes በይነገጽን ይደግፋል

I2S/PCM/ AC97

• ሶስት I2S / PCM በይነገጽ
• የሚክ ድርድርን እስከ 8ch PDM/TDM በይነገጽ ይደግፉ
• PWM የድምጽ ውፅዓትን ይደግፉ

ዩኤስቢ እና PCIE

• ሁለት 2.0 ዩኤስቢ በይነገጾች
• One USB 2.0 OTG and one 2.0 USB host

ኤተርኔት

• RTL8211F በመርከቡ ላይ
• ድጋፍ 10/100/1000M

I2C

• እስከ አምስት I2Cs
• መደበኛ ሁነታን እና ፈጣን ሁነታን ይደግፉ (እስከ 400 ኪቢ / ሰ)

ኤስዲኦ

• 2CH SDIO 3.0 ፕሮቶኮልን ይደግፉ

SPI

• እስከ ሁለት የ SPI መቆጣጠሪያዎች;
• ሙሉ-ዱፕሌክስ የተመሳሰለ ተከታታይ በይነገጽ

UART

• እስከ 6 UARTs ድረስ ይደግፉ
• UART2 ከ 2 ገመዶች ጋር ለማረም መሳሪያዎች
• Embedded two 664-byte FIFOs
• ለ UART0/1/3/4/5 ራስ-ሰር ፍሰት መቆጣጠሪያ ሁነታን ይደግፉ

ኤ.ዲ.ሲ

• እስከ አራት የኤዲሲ ቻናሎች
• 12-ቢት ጥራት
• ጥራዝtagሠ ግቤት ከ 0V እስከ 1.8V መካከል ያለው ክልል
• እስከ 1ኤምኤስ/ኤስኤስ ድረስ ይደግፉampየሊንግ ተመን

PWM

• 11 በቺፕ ላይ PWMs በማቋረጥ ላይ የተመሰረተ አሰራር
• Support 32-bit time/counter facility
• የ IR አማራጭ በ PWM3/7 ላይ

የኃይል አሃድ

• በቦርዱ ላይ ልዩ ኃይል
• ነጠላ 3.3 ቪ ግቤት

CM1126B-P Block Diagram

RV1126B-P Block Diagram

የልማት ሰሌዳ (Idea1126) አግድ ንድፍ

CM1126B-P PCB Dimension

CM1126B-P Pin Definition

ፒን	ሲግናል	መግለጫ ወይም ተግባራት	GPIO ተከታታይ	አይኦ ጥራዝtage
1	LCDC_D19_3V3	I2S1_MCLK_M2/CIF_D15_M1	GPIO2_C7_d	3.3 ቪ
2	LCDC_D20_3V3	I2S1_SDO_M2/CIF_VS_M1	GPIO2_D0_d	3.3 ቪ
3	LCDC_D21_3V3	I2S1_SCLK_M2/CIF_CLKO_M1	GPIO2_D1_d	3.3 ቪ
4	LCDC_D22_3V3	I2S1_LRCK_M2/CIF_CKIN_M1	GPIO2_D2_d	3.3 ቪ
5	LCDC_D23_3V3	I2S1_SDI_M2/CIF_HS_M1	GPIO2_D3_d	3.3 ቪ
6	ጂኤንዲ	መሬት		0V
7	GPIO1_D1	UART1_RX_M1/I2C5_SDA_M2	GPIO1_D1_d	3.3V(V2)
8	BT_WAKE	SPI0_CS1n_M0	GPIO0_A4_u	3.3V(V2)
9	WIFI_REG_ON	SPI0_MOSI_M0	GPIO0_A6_d	3.3V(V2)
10	BT_RST	SPI0_MISO_M0	GPIO0_A7_d	3.3V(V2)
11	WIFI_WAKE_HOST	SPI0_CLK_M0	GPIO0_B0_d	3.3V(V2)
12	BT_WAKE_HOST	SPI0_CS0n_M0	GPIO0_A5_u	3.3V(V2)
13	PWM7_IR_M0_3V3		GPIO0_B1_d	3.3 ቪ
14	PWM6_M0_3V3	TSADC_SHUT_M1	GPIO0_B2_d	3.3 ቪ
15	UART2_TX_3V3	ለማረም	GPIO3_A2_u	3.3 ቪ
16	UART2_RX_3V3	ለማረም	GPIO3_A3_u	3.3 ቪ
17	I2S0_MCLK_M0_3V 3		GPIO3_D2_d	3.3 ቪ
18	I2S0_SCLK_TX_M0 _3 ቪ3	ACODEC_DAC_CLK	GPIO3_D0_d	3.3 ቪ
19	I2S0_SDI3_M0_3V3	PDM_SDI3_M0 / ACODEC_ADC_DATA	GPIO3_D7_d	3.3 ቪ
20	I2S0_SDO0_M0_3V 3	ACODEC_DAC_DATAR /APWM_R_M1/ADSM_LP	GPIO3_D5_d	3.3 ቪ

ፒን	ሲግናል	መግለጫ ወይም ተግባራት	GPIO ተከታታይ	አይኦ ጥራዝtage
21	I2S0_LRCK_TX_M0 _3 ቪ3	ACODEC_DAC_SYNC /APWM_L_M1/ADSM_LN	GPIO3_D3_d	3.3 ቪ
22	PDM_SDI1_3V3	I2S0_SDO3_SDI1_M0/I2C4SDA	GPIO4_A1_d	3.3 ቪ
23	PDM_CLK1_3V3	I2S0_SCK_RX_M0	GPIO3_D1_d	3.3 ቪ
24	PDM_SDI2_3V3	I2S0_SDO2_SDI2_M0/I2C4SCL	GPIO4_A0_d	3.3 ቪ
25	PDM_SDI0_3V3	I2S0_SDI0_M0	GPIO3_D6_d	3.3 ቪ
26	PDM_CLK_3V3	I2S0_LRCK_RX_M0	GPIO3_D4_d	3.3 ቪ
27	I2C2_SDA_3V3	PWM5_M0	GPIO0_C3_d	3.3 ቪ
28	I2C2_SCL_3V3	PWM4_M0	GPIO0_C2_d	3.3 ቪ
29	USB_HOST_DP			1.8 ቪ
30	USB_HOST_DM			1.8 ቪ
31	ጂኤንዲ	መሬት		0V
32	OTG_DP	Can be used for download		1.8 ቪ
33	OTG_DM	Can be used for download		1.8 ቪ
34	OTG_DET(V2)	OTG VBUS DET ውስጥ		3.3V(V2)
35	OTG_ID			1.8 ቪ
36	SPI0_CS1n_M1	I2S1_MCK_M1/UART4_TX_M2	GPIO1_D5_d	1.8 ቪ
37	VCC3V3_SYS	3.3V ዋና ኃይል ግብዓት		3.3 ቪ
38	VCC3V3_SYS	3.3V ዋና ኃይል ግብዓት		3.3 ቪ
39	USB_CTRL_3V3		GPIO0_C1_d	3.3 ቪ
40	SDMMC0_DET	ለኤስዲ ካርድ ጥቅም ላይ መዋል አለበት	GPIO0_A3_u	3.3V(V2)
41	CLKO_32ኬ	የ RTC ሰዓት ውፅዓት	GPIO0_A2_u	3.3V(V2)
42	n ዳግም አስጀምር	የቁልፍ ግቤትን ዳግም አስጀምር		3.3V(V2)
43	MIPI_CSI_RX0_CL KP	MIPI CSI0 ወይም LVDS0 ግቤት		1.8 ቪ
44	MIPI_CSI_RX0_CL KN	MIPI CSI0 ወይም LVDS0 ግቤት		1.8 ቪ
45	MIPI_CSI_RX0_D2 P	MIPI CSI0 ወይም LVDS0 ግቤት		1.8 ቪ
46	MIPI_CSI_RX0_D2 N	MIPI CSI0 ወይም LVDS0 ግቤት		1.8 ቪ
47	MIPI_CSI_RX0_D3 P	MIPI CSI0 ወይም LVDS0 ግቤት		1.8 ቪ
48	MIPI_CSI_RX0_D3 N	MIPI CSI0 ወይም LVDS0 ግቤት		1.8 ቪ
49	MIPI_CSI_RX0_D1 P	MIPI CSI0 ወይም LVDS0 ግቤት		1.8 ቪ
50	MIPI_CSI_RX0_D1 N	MIPI CSI0 ወይም LVDS0 ግቤት		1.8 ቪ
51	MIPI_CSI_RX0_D0 P	MIPI CSI0 ወይም LVDS0 ግቤት		1.8 ቪ

ፒን	ሲግናል	መግለጫ ወይም ተግባራት	GPIO ተከታታይ	አይኦ ጥራዝtage
52	MIPI_CSI_RX0_D0 N	MIPI CSI0 ወይም LVDS0 ግቤት		1.8 ቪ
53	ጂኤንዲ	መሬት		0V
54	MIPI_CSI_RX1_D3 P	MIPI CSI1 ወይም LVDS1 ግቤት		1.8 ቪ
55	MIPI_CSI_RX1_D3 N	MIPI CSI1 ወይም LVDS1 ግቤት		1.8 ቪ
56	MIPI_CSI_RX1_CL KP	MIPI CSI1 ወይም LVDS1 ግቤት		1.8 ቪ
57	MIPI_CSI_RX1_CL KN	MIPI CSI1 ወይም LVDS1 ግቤት		1.8 ቪ
58	MIPI_CSI_RX1_D2 P	MIPI CSI1 ወይም LVDS1 ግቤት		1.8 ቪ
59	MIPI_CSI_RX1_D2 N	MIPI CSI1 ወይም LVDS1 ግቤት		1.8 ቪ
60	MIPI_CSI_RX1_D1 P	MIPI CSI1 ወይም LVDS1 ግቤት		1.8 ቪ
61	MIPI_CSI_RX1_D1 N	MIPI CSI1 ወይም LVDS1 ግቤት		1.8 ቪ
62	MIPI_CSI_RX1_D0 P	MIPI CSI1 ወይም LVDS1 ግቤት		1.8 ቪ
63	MIPI_CSI_RX1_D0 N	MIPI CSI1 ወይም LVDS1 ግቤት		1.8 ቪ
64	SDMMC0_D3_3V3	UART3_TX_M1	GPIO1_A7_u	3.3 ቪ
65	SDMMC0_D2_3V3	UART3_RX_M1	GPIO1_A6_u	3.3 ቪ
66	SDMMC0_D1_3V3	UART2_TX_M0	GPIO1_A5_u	3.3 ቪ
67	SDMMC0_D0_3V3	UART2_RX_M0	GPIO1_A4_u	3.3 ቪ
68	SDMMC0_CMD_3V 3	UART3_CTSn_M1	GPIO1_B1_u	3.3 ቪ
69	SDMMC0_CLK_3V3	UART3_RTSn_M1	GPIO1_B0_u	3.3 ቪ
70	ጂኤንዲ	መሬት		0V
71	LED1/CFG_LDO0	የኤተርኔት አገናኝ LED		3.3 ቪ
72	LED2/CFG_LDO1	የኤተርኔት ፍጥነት LED		3.3 ቪ
73	MDI0 +	የኤተርኔት MDI ምልክት		1.8 ቪ
74	MDI0-	የኤተርኔት MDI ምልክት		1.8 ቪ
75	MDI1 +	የኤተርኔት MDI ምልክት		1.8 ቪ
76	MDI1-	የኤተርኔት MDI ምልክት		1.8 ቪ
77	MDI2 +	የኤተርኔት MDI ምልክት		1.8 ቪ
78	MDI2-	የኤተርኔት MDI ምልክት		1.8 ቪ
79	MDI3 +	የኤተርኔት MDI ምልክት		1.8 ቪ
80	MDI3-	የኤተርኔት MDI ምልክት		1.8 ቪ
81	I2C1_SCL	UART4_CTSn_M2	GPIO1_D3_ዩ	1.8 ቪ

ፒን	ሲግናል	መግለጫ ወይም ተግባራት	GPIO ተከታታይ	አይኦ ጥራዝtage
82	I2C1_SDA	UART4_RTSn_M2	GPIO1_D2_ዩ	1.8 ቪ
83	MIPI_CSI_PWDN0	UART4_RX_M2	GPIO1_D4_d	1.8 ቪ
84	SPI0_CLK_M1	I2S1_SDO_M1/UART5_RX_M2	GPIO2_A1_d	1.8 ቪ
85	SPI0_MOSI_M1	I2S1_SCK_M1/I2C3_SCL_M2	GPIO1_D6_d	1.8 ቪ
86	SPI0_CS0n_M1	I2S1_SDI_M1/UART5_TX_M2	GPIO2_A0_d	1.8 ቪ
87	SPI0_MISO_M1	I2S1_LRCK_M1/I2C3_SDA_M2	GPIO1_D7_d	1.8 ቪ
88	MIPI_CSI_CLK1	UART5_RTSn_M2	GPIO2_A2_d	1.8 ቪ
89	MIPI_CSI_CLK0	UART5_CTSn_M2	GPIO2_A3_d	1.8 ቪ
90	ጂኤንዲ	መሬት		0V
91	LCDC_D0_3V3	UART4_RTSn_M1/CIF_D0_M1	GPIO2_A4_d	3.3 ቪ
92	LCDC_D1_3V3	UART4_CTSn_M1/CIF_D1_M1	GPIO2_A5_d	3.3 ቪ
93	LCDC_D2_3V3	UART4_TX_M1/CIF_D2_M1	GPIO2_A6_d	3.3 ቪ
94	LCDC_D3_3V3	UART4_RX_M1/I2S2_SDO_M1	GPIO2_A7_d	3.3 ቪ
95	LCDC_D4_3V3	UART5_TX_M1/I2S2_SDI_M1	GPIO2_B0_d	3.3 ቪ
96	LCDC_D5_3V3	UART5_RX_M1/I2S2_SCK_M1	GPIO2_B1_d	3.3 ቪ
97	LCDC_D6_3V3	UART5_RTSn_M1/I2S2_LRCK_ M1	GPIO2_B2_d	3.3 ቪ
98	LCDC_D7_3V3	UART5_CTSn_M1/I2S2_MCLK_ M1/CIF_D3_M1	GPIO2_B3_d	3.3 ቪ
99	CAN_RX_3V3	UART3_TX_M2/I2C4_SCL_M0	GPIO3_A0_u	3.3 ቪ
100	CAN_TX_3V3	UART3_RX_M2/I2C4_SDA_M0	GPIO3_A1_u	3.3 ቪ
101	LCDC_CLK_3V3	UART3_CTSn_M2/SPI1_MISO_ M2/PWM8_M1	GPIO2_D7_d	3.3 ቪ
102	LCDC_VSYNC_3V3	UART3_RTSn_M2/SPI1_MOSI	GPIO2_D6_d	3.3 ቪ
103	MIPI_DSI_D2P			1.8 ቪ
104	MIPI_DSI_D2N			1.8 ቪ
105	MIPI_DSI_D1P			1.8 ቪ
106	MIPI_DSI_D1N			1.8 ቪ
107	MIPI_DSI_D0P			1.8 ቪ
108	MIPI_DSI_D0N			1.8 ቪ
109	MIPI_DSI_D3P			1.8 ቪ
110	MIPI_DSI_D3N			1.8 ቪ
111	MIPI_DSI_CLKP			1.8 ቪ
112	MIPI_DSI_CLKN			1.8 ቪ
113	ADCIN3	የኤዲሲ ግብዓት		1.8 ቪ
114	ADCIN2	የኤዲሲ ግብዓት		1.8 ቪ
115	ADCIN1	የኤዲሲ ግብዓት		1.8 ቪ
116	ADKEY_IN0	የመልሶ ማግኛ ሁነታ ስብስብ (10 ኪ PU)		1.8 ቪ
117	ጂኤንዲ	መሬት		0V
118	SDIO_CLK		GPIO1_B2_d	3.3V(V2)
119	SDIO_CMD		GPIO1_B3_u	3.3V(V2)

ፒን	ሲግናል	መግለጫ ወይም ተግባራት	GPIO ተከታታይ	አይኦ ጥራዝtage
120	SDIO_D0		GPIO1_B4_u	3.3V(V2)
121	SDIO_D1		GPIO1_B5_u	3.3V(V2)
122	SDIO_D2		GPIO1_B6_u	3.3V(V2)
123	SDIO_D3		GPIO1_B7_u	3.3V(V2)
124	UART0_RX		GPIO1_C2_u	3.3V(V2)
125	UART0_TX		GPIO1_C3_u	3.3V(V2)
126	UART0_CTSN		GPIO1_C1_u	3.3V(V2)
127	UART0_RTSN		GPIO1_C0_u	3.3V(V2)
128	PCM_TX	I2S2_SDO_M0/SPI1_MOSI_M1	GPIO1_C4_d	3.3V(V2)
129	PCM_SYNC	I2S2_LRCK_M0/SPI1_CSn0_M 1/UART1_CTSn_M1	GPIO1_C7_d	3.3V(V2)
130	PCM_CLK	I2S2_SCLK_M0/SPI1_CLK_M1/ UART1_RTSn_M1	GPIO1_C6_d	3.3V(V2)
131	PCM_RX	I2S2_SDI_M0/SPI1_MISO_M1	GPIO1_C5_d	3.3V(V2)
132	LCDC_D15_3V3	CIF_D11_M1	GPIO2_C3_d	3.3 ቪ
133	LCDC_D14_3V3	CIF_D10_M1	GPIO2_C2_d	3.3 ቪ
134	LCDC_D13_3V3	CIF_D9_M1	GPIO2_C1_d	3.3 ቪ
135	LCDC_D12_3V3	CIF_D8_M1	GPIO2_C0_d	3.3 ቪ
136	LCDC_DEN_3V3	I2C3_SCL_M1/SPI1_CS0n_M2	GPIO2_D4_d	3.3 ቪ
137	LCDC_D10_3V3	CIF_D6_M1	GPIO2_B6_d	3.3 ቪ
138	LCDC_D9_3V3	CIF_D5_M1	GPIO2_B5_d	3.3 ቪ
139	LCDC_D8_3V3	CIF_D4_M1	GPIO2_B4_d	3.3 ቪ
140	LCDC_D11_3V3	CIF_D7_M1	GPIO2_B7_d	3.3 ቪ
141	LCDC_HSYNC_3V3	I2C3_SDA_M1/SPI1_CLK_M2	GPIO2_D5_d	3.3 ቪ
142	LCDC_D16_3V3	CIF_D12_M1	GPIO2_C4_d	3.3 ቪ
143	LCDC_D17_3V3	CIF_D13_M1	GPIO2_C5_d	3.3 ቪ
144	LCDC_D18_3V3	CIF_D14_M1	GPIO2_C6_d	3.3 ቪ
ማስታወሻ፡- 1.     አብዛኞቹ GPIO ጥራዝtagሠ 1.8 ቪ ነው፣ ግን አንዳንድ ፒኖች 3.3 ቪ ምልክት ተደርጎባቸዋል። 2.     GPIO voltage change to 3.3V for marked (V2).

የልማት ኪት (Idea1126)

የሃርድዌር ንድፍ መመሪያ

የዳርቻ ወረዳ ማጣቀሻ

ዋና የኃይል ዑደት

የወረዳ ማረም

የዩኤስቢ OTG በይነገጽ ዑደት

PCB የእግር አሻራ

የምርት ኤሌክትሪክ ባህሪያት

መበታተን እና የሙቀት መጠን

ምልክት	መለኪያ	ደቂቃ	ተይብ	ከፍተኛ	ክፍል
VCC3V3_SYS	ስርዓት አይ.ኦ ጥራዝtage	3.3-5%	3.3	3.3 + 5%	V
ኢሲስ_ውስጥ	VCC3V3_SYS ግቤት የአሁን		850		mA
Ta	የአሠራር ሙቀት	-20		70	° ሴ
Tstg	የማከማቻ ሙቀት	-40		85	° ሴ

የፈተና አስተማማኝነት

	የከፍተኛ ሙቀት ኦፕሬቲንግ ሙከራ
ይዘቶች	Operating 8h in high temperatures	55 ° ሴ ± 2 ° ሴ
ውጤት	ቲቢዲ

 

	የክወና ህይወት ፈተና
ይዘቶች	Operating in the room	120 ሰ
ውጤት	ቲቢዲ

የተወሰነ ዋስትና
Boardcon warrants this product to be free of defects in material and workmanship for one year from the date of purchase. During this warranty period, Boardcon will repair or replace the defective unit by the following process: A copy of the original invoice must be included when returning the defective unit to Boardcon. This limited warranty does not cover damages resulting from lightning or other power surges, misuse, abuse, abnormal conditions of operation, or attempts to alter or modify the function of the product. This warranty is limited to the repair or replacement of the defective unit. In no event shall Boardcon be liable or responsible for any loss or damages, including but not limited to any lost profits, incidental or consequential damages, loss of business, or anticipatory profits arising from the use or inability to use this product. Repairs made after the expiration of the warranty period are subject to a repair charge and the cost of return shipping. Please contact Boardcon to arrange for any repair service and to obtain repair charge information.

የሚጠየቁ ጥያቄዎች

Q: How do I upgrade the DDR memory on CM1126B-P?
A: The CM1126B-P supports up to 4GB LPDDR4 memory. To upgrade, ensure compatibility with the specifications and follow recommended procedures.

Q: What is the power supply requirement for CM1126B-P?
A: The power requirement for CM1126B-P is DC 3.3V. Ensure to provide a stable power supply within this range for optimal performance.

Q: Can I expand the storage capacity of eMMC on CM1126B-P?
A: Yes, the eMMC storage on CM1126B-P can be expanded up to 256GB. Ensure compatibility with supported storage devices before upgrading.

ሰነዶች / መርጃዎች

Boardcon Embedded CM1126B-P System on Module [pdf] የተጠቃሚ መመሪያ V2.20250422, CM1126B-P System on Module, CM1126B-P, System on Module, Module

ዋቢዎች

• የተጠቃሚ መመሪያ