Boardcon Embedded CM1126B-P System on Module
Sonraíochtaí
| Gné | Sonraíochtaí |
| LAP | Cortex Quad-lárnach-A53 |
| DDR | 2GB LPDDR4 (suas le 4GB) |
| eMMC Flash | 8GB (suas le 256GB) |
| Cumhacht | DC 3.3V |
| MIPI DSI | 4-Lána |
| I2S | 4-CH |
| MIPI CSI | 2-CH 4-Lána |
| RGB LCD | 24 ghiotán |
| Ceamara | 1-CH(DVP) agus 2-CH(CSI) |
| USB | 2-CH (USB HOST 2.0 and OTG 2.0) |
| Ethernet | 1000m GMAC |
| SDMMC | 2-CH |
| I2C | 5-CH |
| SPI | 2-CH |
| UART | 5-CH, 1-CH(DEBUG) |
| PWM | 11-CH |
| ADC IN | 4-CH |
| Toise an Bhoird | 34 x 35mm |
Réamhrá
Maidir leis an Lámhleabhar seo
Tá sé mar aidhm ag an lámhleabhar seo ceann eile a sholáthar don úsáideoirview of the board and its benefits, complete feature specifications, and setup procedures. It contains important safety information as well.
Aiseolas agus Nuashonrú ar an Lámhleabhar seo
Chun cabhrú lenár gcustaiméirí an leas is fearr a bhaint as ár gcuid táirgí, táimid i gcónaí ag cur acmhainní breise agus nuashonraithe ar fáil ar an Boardcon websuíomh (www.boardcon.com, www.armdesigner.com). Ina measc seo tá lámhleabhair, nótaí feidhmchláir, ríomhchlárú examples, agus bogearraí agus crua-earraí nuashonraithe. Seiceáil isteach go tréimhsiúil chun a fheiceáil cad atá nua! Agus muid ag tabhairt tosaíochta d’obair ar na hacmhainní nuashonraithe seo, is é aiseolas ó chustaiméirí an príomhthionchar, Má tá ceisteanna, tuairimí nó imní agat faoi do tháirge nó do thionscadal, ná bíodh drogall ort teagmháil a dhéanamh linn ag tacaíocht@armdesigner.com.
CM1126B-P Introduction
Achoimre
The CM1126B-P system-on-module is equipped with Rockchip’s RV1126B-P, built with a quad-core Cortex-A53, 3.0 TOPs NPU, and RISC-V MCU. It is designed specifically for the IPC/CVR devices, AI Camera devices, intelligent interactive devices, and mini robots. High-performance and low-power solutions can help customers introduce new technologies more quickly and enhance the overall solution efficiency. The smallest size can be put on a 38board. Following the hardware revision from CM1126 (V1) to CM1126B-P (V2), where the SoC is updated to the RV1126B-P, the Reset & OTG_VBUS signals and the WIFI/BT module’s GPIO voltage must operate at a 3.3V logic level.
Gnéithe
Micreaphróiseálaí
- Quad-lárnach Cortex-A53 suas go dtí 1.6GHz
- I-taisce 32KB agus 32KB D-taisce do gach croí, taisce 512KB L3
- 3.0 TOPS Aonad Próisis Néarachais
- RISC-V MCU to support 250ms fast boot
- ISP 12M ar a mhéad
Eagraíocht Cuimhne
- RAM LPDDR4 suas le 4GB
- eMMC suas go dtí 256GB
- SPI Flash suas go dtí 8MB
Díchódóir / Ionchódóir Físeáin
- Tacaíonn sé le díchódú / ionchódú físeáin suas go dtí 4K@30fps
- Tacaíonn sé le díchódú fíor-ama H.264/265
- Tacaíonn ionchódú físe UHD H.264/265 fíor-ama
- Méid an phictiúir suas go dtí 8192×8192
Fochóras Taispeána
- Aschur Físeáin
- Tacaíonn sé le 4 lána MIPI DSI suas go dtí 2560 × 1440@60fps
- Supports 24-bit RGB parallel output
- Íomhá i
- Supports up to 16-bit DVP interface
- Tacaíonn comhéadan 2ch MIPI CSI 4lanes
I2S/PCM/ AC97
- Trí chomhéadan I2S/PCM
- Tacaigh le sraith Mic Suas le comhéadan 8ch PDM/TDM
- Tacaíocht a thabhairt do aschur fuaime PWM
USB agus PCIE
- Dhá chomhéadan USB 2.0
- One USB 2.0 OTG and one 2.0 USB host
Ethernet
- RTL8211F ar bord
- Tacaíocht 10/100/1000M
I2C
- Suas le cúig I2C
- Tacaigh le modh caighdeánach agus modh tapa (suas le 400kbit / s)
SDIO
- Tacaigh le prótacal 2CH SDIO 3.0
SPI
- Suas le dhá rialtóir SPI,
- Comhéadan sraitheach sioncrónach lán-déphléacsach
UART
- Tacaíocht a thabhairt do suas le 6 UART
- UART2 le 2 shreang le haghaidh uirlisí dífhabhtaithe
- Embedded two 664-byte FIFOs
- Tacaigh le modh rialaithe sreabhadh uathoibríoch do UART0/1/3/4/5
ADC
- Suas le ceithre chainéal ADC
- Taifeach 12-giotán
- Imltage raon ionchuir idir 0V go 1.8V
- Tacaíocht suas go dtí 1MS / ssampráta ling
PWM
- 11 PWM ar-sliseanna le hoibríocht idirbhriste
- Support 32-bit time/counter facility
- Rogha IR ar PWM3/7
Aonad cumhachta
- Cumhacht Scoite ar bord
- Aonair ionchur 3.3V
CM1126B-P Block Diagram
RV1126B-P Block Diagram
Léaráid Bhloc den Bhord Forbartha (Idea1126)
CM1126B-P PCB Dimension
CM1126B-P Pin Definition
| Bioráin | Comhartha | Tuairisc nó feidhmeanna | Sraitheach GPIO | IO Imltage |
| 1 | LCDC_D19_3V3 | I2S1_MCLK_M2/CIF_D15_M1 | GPIO2_C7_d | 3.3V |
| 2 | LCDC_D20_3V3 | I2S1_SDO_M2/CIF_VS_M1 | GPIO2_D0_d | 3.3V |
| 3 | LCDC_D21_3V3 | I2S1_SCLK_M2/CIF_CLKO_M1 | GPIO2_D1_d | 3.3V |
| 4 | LCDC_D22_3V3 | I2S1_LRCK_M2/CIF_CKIN_M1 | GPIO2_D2_d | 3.3V |
| 5 | LCDC_D23_3V3 | I2S1_SDI_M2/CIF_HS_M1 | GPIO2_D3_d | 3.3V |
| 6 | GND | Talamh | 0V | |
| 7 | GPIO1_D1 | UART1_RX_M1/I2C5_SDA_M2 | GPIO1_D1_d | 3.3V(V2) |
| 8 | BT_WAKE | SPI0_CS1n_M0 | GPIO0_A4_u | 3.3V(V2) |
| 9 | WIFI_REG_ON | SPI0_MOSI_M0 | GPIO0_A6_d | 3.3V(V2) |
| 10 | BT_RST | SPI0_MISO_M0 | GPIO0_A7_d | 3.3V(V2) |
| 11 | WIFI_WAKE_HOST | SPI0_CLK_M0 | GPIO0_B0_d | 3.3V(V2) |
| 12 | BT_WAKE_HOST | SPI0_CS0n_M0 | GPIO0_A5_u | 3.3V(V2) |
| 13 | PWM7_IR_M0_3V3 | GPIO0_B1_d | 3.3V | |
| 14 | PWM6_M0_3V3 | TSADC_SHUT_M1 | GPIO0_B2_d | 3.3V |
| 15 | UART2_TX_3V3 | Le haghaidh dífhabhtaithe | GPIO3_A2_u | 3.3V |
| 16 | UART2_RX_3V3 | Le haghaidh dífhabhtaithe | GPIO3_A3_u | 3.3V |
| 17 | I2S0_MCLK_M0_3V
3 |
GPIO3_D2_d | 3.3V | |
| 18 | I2S0_SCLK_TX_M0
_3V3 |
ACODEC_DAC_CLK | GPIO3_D0_d | 3.3V |
| 19 | I2S0_SDI3_M0_3V3 | PDM_SDI3_M0 /
ACODEC_ADC_DATA |
GPIO3_D7_d | 3.3V |
| 20 | I2S0_SDO0_M0_3V
3 |
ACODEC_DAC_DATAR
/APWM_R_M1/ADSM_LP |
GPIO3_D5_d | 3.3V |
| Bioráin | Comhartha | Tuairisc nó feidhmeanna | Sraitheach GPIO | IO Imltage |
| 21 | I2S0_LRCK_TX_M0
_3V3 |
ACODEC_DAC_SYNC
/APWM_L_M1/ADSM_LN |
GPIO3_D3_d | 3.3V |
| 22 | PDM_SDI1_3V3 | I2S0_SDO3_SDI1_M0/I2C4SDA | GPIO4_A1_d | 3.3V |
| 23 | PDM_CLK1_3V3 | I2S0_SCK_RX_M0 | GPIO3_D1_d | 3.3V |
| 24 | PDM_SDI2_3V3 | I2S0_SDO2_SDI2_M0/I2C4SCL | GPIO4_A0_d | 3.3V |
| 25 | PDM_SDI0_3V3 | I2S0_SDI0_M0 | GPIO3_D6_d | 3.3V |
| 26 | PDM_CLK_3V3 | I2S0_LRCK_RX_M0 | GPIO3_D4_d | 3.3V |
| 27 | I2C2_SDA_3V3 | PWM5_M0 | GPIO0_C3_d | 3.3V |
| 28 | I2C2_SCL_3V3 | PWM4_M0 | GPIO0_C2_d | 3.3V |
| 29 | USB_HOST_DP | 1.8V | ||
| 30 | USB_HOST_DM | 1.8V | ||
| 31 | GND | Talamh | 0V | |
| 32 | OTG_DP | Can be used for download | 1.8V | |
| 33 | OTG_DM | Can be used for download | 1.8V | |
| 34 | OTG_DET(V2) | OTG VBUS DET IN | 3.3V(V2) | |
| 35 | OTG_ID | 1.8V | ||
| 36 | SPI0_CS1n_M1 | I2S1_MCK_M1/UART4_TX_M2 | GPIO1_D5_d | 1.8V |
| 37 | VCC3V3_SYS | Ionchur Príomhchumhachta 3.3V | 3.3V | |
| 38 | VCC3V3_SYS | Ionchur Príomhchumhachta 3.3V | 3.3V | |
| 39 | USB_CTRL_3V3 | GPIO0_C1_d | 3.3V | |
| 40 | SDMMC0_DET | Ní mór é a úsáid le haghaidh Cárta SD | GPIO0_A3_u | 3.3V(V2) |
| 41 | CLKO_32K | Aschur clog RTC | GPIO0_A2_u | 3.3V(V2) |
| 42 | nRESET | Athshocraigh ionchur eochair | 3.3V(V2) | |
| 43 | MIPI_CSI_RX0_CL
KP |
Ionchur MIPI CSI0 nó LVDS0 | 1.8V | |
| 44 | MIPI_CSI_RX0_CL
KN |
Ionchur MIPI CSI0 nó LVDS0 | 1.8V | |
| 45 | MIPI_CSI_RX0_D2
P |
Ionchur MIPI CSI0 nó LVDS0 | 1.8V | |
| 46 | MIPI_CSI_RX0_D2
N |
Ionchur MIPI CSI0 nó LVDS0 | 1.8V | |
| 47 | MIPI_CSI_RX0_D3
P |
Ionchur MIPI CSI0 nó LVDS0 | 1.8V | |
| 48 | MIPI_CSI_RX0_D3
N |
Ionchur MIPI CSI0 nó LVDS0 | 1.8V | |
| 49 | MIPI_CSI_RX0_D1
P |
Ionchur MIPI CSI0 nó LVDS0 | 1.8V | |
| 50 | MIPI_CSI_RX0_D1
N |
Ionchur MIPI CSI0 nó LVDS0 | 1.8V | |
| 51 | MIPI_CSI_RX0_D0
P |
Ionchur MIPI CSI0 nó LVDS0 | 1.8V |
| Bioráin | Comhartha | Tuairisc nó feidhmeanna | Sraitheach GPIO | IO Imltage |
| 52 | MIPI_CSI_RX0_D0
N |
Ionchur MIPI CSI0 nó LVDS0 | 1.8V | |
| 53 | GND | Talamh | 0V | |
| 54 | MIPI_CSI_RX1_D3
P |
Ionchur MIPI CSI1 nó LVDS1 | 1.8V | |
| 55 | MIPI_CSI_RX1_D3
N |
Ionchur MIPI CSI1 nó LVDS1 | 1.8V | |
| 56 | MIPI_CSI_RX1_CL
KP |
Ionchur MIPI CSI1 nó LVDS1 | 1.8V | |
| 57 | MIPI_CSI_RX1_CL
KN |
Ionchur MIPI CSI1 nó LVDS1 | 1.8V | |
| 58 | MIPI_CSI_RX1_D2
P |
Ionchur MIPI CSI1 nó LVDS1 | 1.8V | |
| 59 | MIPI_CSI_RX1_D2
N |
Ionchur MIPI CSI1 nó LVDS1 | 1.8V | |
| 60 | MIPI_CSI_RX1_D1
P |
Ionchur MIPI CSI1 nó LVDS1 | 1.8V | |
| 61 | MIPI_CSI_RX1_D1
N |
Ionchur MIPI CSI1 nó LVDS1 | 1.8V | |
| 62 | MIPI_CSI_RX1_D0
P |
Ionchur MIPI CSI1 nó LVDS1 | 1.8V | |
| 63 | MIPI_CSI_RX1_D0
N |
Ionchur MIPI CSI1 nó LVDS1 | 1.8V | |
| 64 | SDMMC0_D3_3V3 | UART3_TX_M1 | GPIO1_A7_u | 3.3V |
| 65 | SDMMC0_D2_3V3 | UART3_RX_M1 | GPIO1_A6_u | 3.3V |
| 66 | SDMMC0_D1_3V3 | UART2_TX_M0 | GPIO1_A5_u | 3.3V |
| 67 | SDMMC0_D0_3V3 | UART2_RX_M0 | GPIO1_A4_u | 3.3V |
| 68 | SDMMC0_CMD_3V
3 |
UART3_CTSn_M1 | GPIO1_B1_u | 3.3V |
| 69 | SDMMC0_CLK_3V3 | UART3_RTSn_M1 | GPIO1_B0_u | 3.3V |
| 70 | GND | Talamh | 0V | |
| 71 | LED1/CFG_LDO0 | Ethernet LINK stiúir | 3.3V | |
| 72 | LED2/CFG_LDO1 | Ethernet SPEED LED | 3.3V | |
| 73 | MDI0 + | Comhartha MDI Ethernet | 1.8V | |
| 74 | MDI0- | Comhartha MDI Ethernet | 1.8V | |
| 75 | MDI1 + | Comhartha MDI Ethernet | 1.8V | |
| 76 | MDI1- | Comhartha MDI Ethernet | 1.8V | |
| 77 | MDI2 + | Comhartha MDI Ethernet | 1.8V | |
| 78 | MDI2- | Comhartha MDI Ethernet | 1.8V | |
| 79 | MDI3 + | Comhartha MDI Ethernet | 1.8V | |
| 80 | MDI3- | Comhartha MDI Ethernet | 1.8V | |
| 81 | I2C1_SCL | UART4_CTSn_M2 | GPIO1_D3_u | 1.8V |
| Bioráin | Comhartha | Tuairisc nó feidhmeanna | Sraitheach GPIO | IO Imltage |
| 82 | I2C1_SDA | UART4_RTSn_M2 | GPIO1_D2_u | 1.8V |
| 83 | MIPI_CSI_PWDN0 | UART4_RX_M2 | GPIO1_D4_d | 1.8V |
| 84 | SPI0_CLK_M1 | I2S1_SDO_M1/UART5_RX_M2 | GPIO2_A1_d | 1.8V |
| 85 | SPI0_MOSI_M1 | I2S1_SCK_M1/I2C3_SCL_M2 | GPIO1_D6_d | 1.8V |
| 86 | SPI0_CS0n_M1 | I2S1_SDI_M1/UART5_TX_M2 | GPIO2_A0_d | 1.8V |
| 87 | SPI0_MISO_M1 | I2S1_LRCK_M1/I2C3_SDA_M2 | GPIO1_D7_d | 1.8V |
| 88 | MIPI_CSI_CLK1 | UART5_RTSn_M2 | GPIO2_A2_d | 1.8V |
| 89 | MIPI_CSI_CLK0 | UART5_CTSn_M2 | GPIO2_A3_d | 1.8V |
| 90 | GND | Talamh | 0V | |
| 91 | LCDC_D0_3V3 | UART4_RTSn_M1/CIF_D0_M1 | GPIO2_A4_d | 3.3V |
| 92 | LCDC_D1_3V3 | UART4_CTSn_M1/CIF_D1_M1 | GPIO2_A5_d | 3.3V |
| 93 | LCDC_D2_3V3 | UART4_TX_M1/CIF_D2_M1 | GPIO2_A6_d | 3.3V |
| 94 | LCDC_D3_3V3 | UART4_RX_M1/I2S2_SDO_M1 | GPIO2_A7_d | 3.3V |
| 95 | LCDC_D4_3V3 | UART5_TX_M1/I2S2_SDI_M1 | GPIO2_B0_d | 3.3V |
| 96 | LCDC_D5_3V3 | UART5_RX_M1/I2S2_SCK_M1 | GPIO2_B1_d | 3.3V |
| 97 | LCDC_D6_3V3 | UART5_RTSn_M1/I2S2_LRCK_
M1 |
GPIO2_B2_d | 3.3V |
| 98 | LCDC_D7_3V3 | UART5_CTSn_M1/I2S2_MCLK_
M1/CIF_D3_M1 |
GPIO2_B3_d | 3.3V |
| 99 | CAN_RX_3V3 | UART3_TX_M2/I2C4_SCL_M0 | GPIO3_A0_u | 3.3V |
| 100 | CAN_TX_3V3 | UART3_RX_M2/I2C4_SDA_M0 | GPIO3_A1_u | 3.3V |
| 101 | LCDC_CLK_3V3 | UART3_CTSn_M2/SPI1_MISO_
M2/PWM8_M1 |
GPIO2_D7_d | 3.3V |
| 102 | LCDC_VSYNC_3V3 | UART3_RTSn_M2/SPI1_MOSI | GPIO2_D6_d | 3.3V |
| 103 | MIPI_DSI_D2P | 1.8V | ||
| 104 | MIPI_DSI_D2N | 1.8V | ||
| 105 | MIPI_DSI_D1P | 1.8V | ||
| 106 | MIPI_DSI_D1N | 1.8V | ||
| 107 | MIPI_DSI_D0P | 1.8V | ||
| 108 | MIPI_DSI_D0N | 1.8V | ||
| 109 | MIPI_DSI_D3P | 1.8V | ||
| 110 | MIPI_DSI_D3N | 1.8V | ||
| 111 | MIPI_DSI_CLKP | 1.8V | ||
| 112 | MIPI_DSI_CLKN | 1.8V | ||
| 113 | ADCN3 | Ionchur ADC | 1.8V | |
| 114 | ADCN2 | Ionchur ADC | 1.8V | |
| 115 | ADCN1 | Ionchur ADC | 1.8V | |
| 116 | ADKEY_IN0 | Tacar mód athshlánaithe (10K PU) | 1.8V | |
| 117 | GND | Talamh | 0V | |
| 118 | SDIO_CLK | GPIO1_B2_d | 3.3V(V2) | |
| 119 | SDIO_CMD | GPIO1_B3_u | 3.3V(V2) |
| Bioráin | Comhartha | Tuairisc nó feidhmeanna | Sraitheach GPIO | IO Imltage |
| 120 | SDIO_D0 | GPIO1_B4_u | 3.3V(V2) | |
| 121 | SDIO_D1 | GPIO1_B5_u | 3.3V(V2) | |
| 122 | SDIO_D2 | GPIO1_B6_u | 3.3V(V2) | |
| 123 | SDIO_D3 | GPIO1_B7_u | 3.3V(V2) | |
| 124 | UART0_RX | GPIO1_C2_u | 3.3V(V2) | |
| 125 | UART0_TX | GPIO1_C3_u | 3.3V(V2) | |
| 126 | UART0_CTSN | GPIO1_C1_u | 3.3V(V2) | |
| 127 | UART0_RTSN | GPIO1_C0_u | 3.3V(V2) | |
| 128 | PCM_TX | I2S2_SDO_M0/SPI1_MOSI_M1 | GPIO1_C4_d | 3.3V(V2) |
| 129 | PCM_SYNC | I2S2_LRCK_M0/SPI1_CSn0_M
1/UART1_CTSn_M1 |
GPIO1_C7_d | 3.3V(V2) |
| 130 | PCM_CLK | I2S2_SCLK_M0/SPI1_CLK_M1/
UART1_RTSn_M1 |
GPIO1_C6_d | 3.3V(V2) |
| 131 | PCM_RX | I2S2_SDI_M0/SPI1_MISO_M1 | GPIO1_C5_d | 3.3V(V2) |
| 132 | LCDC_D15_3V3 | CIF_D11_M1 | GPIO2_C3_d | 3.3V |
| 133 | LCDC_D14_3V3 | CIF_D10_M1 | GPIO2_C2_d | 3.3V |
| 134 | LCDC_D13_3V3 | CIF_D9_M1 | GPIO2_C1_d | 3.3V |
| 135 | LCDC_D12_3V3 | CIF_D8_M1 | GPIO2_C0_d | 3.3V |
| 136 | LCDC_DEN_3V3 | I2C3_SCL_M1/SPI1_CS0n_M2 | GPIO2_D4_d | 3.3V |
| 137 | LCDC_D10_3V3 | CIF_D6_M1 | GPIO2_B6_d | 3.3V |
| 138 | LCDC_D9_3V3 | CIF_D5_M1 | GPIO2_B5_d | 3.3V |
| 139 | LCDC_D8_3V3 | CIF_D4_M1 | GPIO2_B4_d | 3.3V |
| 140 | LCDC_D11_3V3 | CIF_D7_M1 | GPIO2_B7_d | 3.3V |
| 141 | LCDC_HSYNC_3V3 | I2C3_SDA_M1/SPI1_CLK_M2 | GPIO2_D5_d | 3.3V |
| 142 | LCDC_D16_3V3 | CIF_D12_M1 | GPIO2_C4_d | 3.3V |
| 143 | LCDC_D17_3V3 | CIF_D13_M1 | GPIO2_C5_d | 3.3V |
| 144 | LCDC_D18_3V3 | CIF_D14_M1 | GPIO2_C6_d | 3.3V |
| Nóta:
1. An chuid is mó GPIO voltage 1.8V, ach tá roinnt bioráin marcáilte 3.3V. 2. GPIO imleabhartage change to 3.3V for marked (V2). |
||||
Trealamh Forbartha (Idea1126)
Treoir Dearadh Crua-earraí
Tagairt Chuarda Forimeallach
Ciorcad Príomhchumhachta
Ciorcad Dífhabhtaithe
Ciorcad Comhéadain USB OTG
Lorg PCB
Saintréithe Leictreacha Táirge
Diomailt agus Teocht
| Siombail | Paraiméadar | Min | Clóscríobh | uas | Aonad |
| VCC3V3_SYS | Córas IO
Imltage |
3.3-5% | 3.3 | 3.3 + 5% | V |
| Isys_in | VCC3V3_SYS ionchur Reatha | 850 | mA | ||
| Ta | Teocht Oibriúcháin | -20 | 70 | °C | |
| Tstg | Teocht Stórála | -40 | 85 | °C |
Iontaofacht na Tástála
| Tástáil Oibriúcháin Ardteocht | ||
| Clár ábhair | Operating 8h in high temperatures | 55 ° C ± 2 ° C. |
| Toradh | TBD |
| Tástáil Saoil Oibriúcháin | ||
| Clár ábhair | Operating in the room | 120 uair |
| Toradh | TBD |
Barántas Teoranta
Boardcon warrants this product to be free of defects in material and workmanship for one year from the date of purchase. During this warranty period, Boardcon will repair or replace the defective unit by the following process: A copy of the original invoice must be included when returning the defective unit to Boardcon. This limited warranty does not cover damages resulting from lightning or other power surges, misuse, abuse, abnormal conditions of operation, or attempts to alter or modify the function of the product. This warranty is limited to the repair or replacement of the defective unit. In no event shall Boardcon be liable or responsible for any loss or damages, including but not limited to any lost profits, incidental or consequential damages, loss of business, or anticipatory profits arising from the use or inability to use this product. Repairs made after the expiration of the warranty period are subject to a repair charge and the cost of return shipping. Please contact Boardcon to arrange for any repair service and to obtain repair charge information.
CCanna
Q: How do I upgrade the DDR memory on CM1126B-P?
A: The CM1126B-P supports up to 4GB LPDDR4 memory. To upgrade, ensure compatibility with the specifications and follow recommended procedures.
Q: What is the power supply requirement for CM1126B-P?
A: The power requirement for CM1126B-P is DC 3.3V. Ensure to provide a stable power supply within this range for optimal performance.
Q: Can I expand the storage capacity of eMMC on CM1126B-P?
A: Yes, the eMMC storage on CM1126B-P can be expanded up to 256GB. Ensure compatibility with supported storage devices before upgrading.
Doiciméid / Acmhainní
 |
Boardcon Embedded CM1126B-P System on Module [pdfLámhleabhar Úsáideora V2.20250422, CM1126B-P System on Module, CM1126B-P, System on Module, Module |