UM1075
Incwadi yokusebenzisa
ST-LINK/V2 in-circuit debugger/programmer
ye-STM8 kunye ne-STM32
Intshayelelo
I-ST-LINK/V2 yi-debugger ye-in-circuit/programmer ye-STM8 kunye ne-STM32 microcontrollers. Imodyuli yojongano lwecingo olunye (SWIM) kunye neJTAG/ i-serial wire debugging (SWD) i-interfaces iququzelele unxibelelwano kunye nayiphi na i-STM8 okanye i-STM32 microcontroller esebenza kwibhodi yesicelo.
Ukongeza ekunikezeni imisebenzi efanayo ye-ST-LINK / V2, i-ST-LINK / V2-ISOL ibonisa ukuhlukaniswa kwedijithali phakathi kwePC kunye nebhodi yesicelo esijoliswe kuyo. Ikwamelana nomthamotages ukuya kuthi ga kwi-1000 V RMS.
Ujongano olupheleleyo lwe-USB lwenza unxibelelwano nePC kunye:
- Izixhobo ze-STM8 nge-ST Visual Development (STVD) okanye i-ST Visual Programme (STVP) isoftwe (efumaneka kwi-STMicroelectronics)
- Izixhobo ze-STM32 nge-IAR™, i-Keil ®, i-STM32CubeIDE, i-STM32CubeProgrammer, kunye ne-STM32CubeMonitor imimandla yophuhliso edibeneyo.
Iimbonakalo
- Amandla e-5 V anikezelwe sisidibanisi se-USB
- I-USB 2.0 ujongano oluhambelana nesantya esigcweleyo
- I-USB esemgangathweni-A ukuya kwintambo encinci ye-B
- Iimpawu ezikhethekileyo ze-SWIM
– 1.65 ukuba 5.5 V isicelo voltage ixhaswa kwi-SWIM interface
-SWIM ezinesantya esisezantsi kunye neendlela ezinesantya esiphezulu ezixhaswayo
-Isantya senkqubo ye-SWIM: 9.7 kunye ne-12.8 Kbytes/s, ngokulandelelanayo, kwisantya esiphantsi kunye nesiphezulu
-Intambo ye-SWIM yoqhagamshelo kwisicelo nge-ERNI ethe nkqo esemgangathweni (ref: 284697 okanye 214017) okanye ethe tye (ref: 214012) isinxibelelanisi
-Intambo ye-SWIM yokudibanisa kwisicelo nge-header ye-pin okanye i-2.54 mm pitch connector - JTAG/ SWD (Serial Wire Debug) iimpawu ezithile
– 1.65 ukuba 3.6 V isicelo voltagexhaswa kwi-JTAG/I-SWD interface kunye ne-5 V yokunyamezela amagalelo (a)
-JTAG intambo yokuqhagamshela kwi-J eqhelekileyoTAG I-20-pin pitch 2.54 mm isinxibelelanisi
– Ixhasa uJTAG unxibelelwano, ukuya kuthi ga kwi-9 MHz (ehlala ikho: 1.125 MHz)
-Ixhasa i-serial debug (SWD) ukuya kuthi ga kwi-4 MHz (ehlala ikho: 1.8 MHz), kunye nocingo olulandelelanayo viewer (SWV) unxibelelwano, ukuya kuthi ga kwi-2 MHz - Inqaku lohlaziyo lwe-firmware oluxhaswayo (DFU)
- Imo ye-LED, idanyaza ngexesha lonxibelelwano nePC
- 1000 V RMS high isolation voltage (ST-LINK/V2-ISOL kuphela)
- Ubushushu bokusebenza ukusuka kwi-0 ukuya kuma-50 degrees Celsius
Ukuodola ulwazi
Ukuodola i-ST-LINK/V2, bhekisa kwiThebhule yoku-1.
Itheyibhile 1. Uluhlu lweekhowudi zoku-odola
| Ikhowudi yoku-odola | ST-LINK inkcazelo |
| ST-LINK/V2 | Kwi-circuit debugger/umdwelisi |
| ST-LINK/V2-ISOL | I-debugger ye-in-circuit/programmer ene-digital isolation |
a. I-ST-LINK/V2 inokunxibelelana neethagethi ezisebenza ngaphantsi kwe-3.3 V kodwa ivelisa imiqondiso yokuphuma kule voltage kwinqanaba. Iithagethi ze-STM32 ziyakunyamezela oku kugqithiswatage. Ukuba amanye amacandelo ebhodi ekujoliswe kuyo anengqiqo, sebenzisa i-ST-LINK/V2-ISOL, STLINK-V3MINIE, okanye i-STLINK-V3SET ene-adapter ye-B-STLINK-VOLT ukuphepha impembelelo yokugqithisa.tage isitofu ebhodini.
Imixholo yemveliso
Iintambo ezinikezelweyo ngaphakathi kwemveliso ziboniswe kwi-Figure 2 kunye ne-Figure 3. Zibandakanya (ukusuka kwesobunxele ukuya kwesokudla):
- Umgangatho we-USB osemgangathweni-A ukuya kwintambo encinci ye-B (A)
- ST-LINK/V2 debugging kunye neprogramming (B)
- Isidibanisi se-SWIM esibiza ixabiso eliphantsi (C)
- Iribhoni ye-SWIM ethe tyaba eneqhagamshelo elisemgangathweni le-ERNI kwelinye icala (D)
- JTAG okanye i-SWD kunye ne-SWV iribhoni ecaba ene-20-pin isiqhagamshelanisi (E)
Ubumbeko lwe-Hardware
I-ST-LINK/V2 iyilwe malunga nesixhobo se-STM32F103C8, esibandakanya ukusebenza okuphezulu kweArm ®(a) Cortex®.
-M3 engundoqo. Ifumaneka kwiphakheji ye-TQFP48.
Njengoko kubonisiwe kuMfanekiso 4, i-ST-LINK/V2 ibonelela ngeziqhagamshelo ezimbini:
- Isidibanisi se-STM32 seJTAG/ SWD kunye ne-SWV interface
- Isidibanisi se-STM8 sojongano lweSWIM
I-ST-LINK/V2-ISOL ibonelela ngesidibanisi esinye se-STM8 SWIM, STM32 JTAG/SWD, kunye ne-SWV ujongano.
- A = STM32 JTAG kunye ne-SWD target connector
- B = STM8 SWIM isiqhagamshelanisi ekujoliswe kuko
- C = STM8 SWIM, STM32 JTAG, kunye ne-SWD target connector
- D = Umsebenzi wonxibelelwano we-LED
4.1 Uqhagamshelwano ne-STM8
Ukuphuhliswa kwezicelo ezisekelwe kwi-STM8 microcontrollers, i-ST-LINK / V2 inokudibaniswa nebhodi ekujoliswe kuyo ngeentambo ezimbini ezahlukeneyo, kuxhomekeke kwikhonkco ekhoyo kwibhodi yesicelo.
Ezi ntambo zezi:
- Iribhoni ye-SWIM ethe tyaba enekhonkco eliqhelekileyo le-ERNI kwelinye icala
- Intambo yoku-SWIM ene-4-pin ezimbini, iziqhagamshelo eziyi-2.54 mm okanye iintambo zocingo ezi-SWIM ezahlukeneyo
4.1.1 Uqhagamshelwano olusemgangathweni lwe-ERNI kunye neribhoni ye-SWIM emcaba
Umzobo we-5 ubonisa indlela yokudibanisa i-ST-LINK / V2 ukuba i-ERNI 4-pin ye-SWIM ikhonkco ye-SWIM ikhona kwibhodi yesicelo.
- A = Ibhodi yesicelo ekujoliswe kuyo ene-ERNI isinxibelelanisi
- B = Intambo yocingo ene-ERNI isinxibelelanisi kwelinye icala
- C = STM8 SWIM isiqhagamshelanisi ekujoliswe kuko
- Jonga uMfanekiso 11
Umzobo we-6 ubonisa ukuba i-pin 16 ilahlekile kwi-ST-LINK/V2-ISOL ikhonkco ekujoliswe kuyo. Esi sikhonkwane singekho sisetyenziswa njengesitshixo sokhuseleko kwisidibanisi sentambo, ukuqinisekisa indawo echanekileyo yentambo ye-SWIM kwisidibanisi ekujoliswe kuso nditsho nezikhonkwane ezisetyenziselwa zombini iSWIM ne-J.TAG iintambo.
4.1.2 Ukudityaniswa kwe-SWIM ngexabiso eliphantsi
Umzobo we-7 ubonisa indlela yokudibanisa i-ST-LINK / V2 ukuba i-4-pin, 2.54 mm, i-swim connector yexabiso eliphantsi ikhona kwibhodi yesicelo.
- A = Ibhodi yesicelo ekujoliswe kuyo nge-4-pin, i-2.54 mm, isixhumi esinexabiso eliphantsi
- B = Intambo yocingo eneqhosha le-4-pin okanye intambo yocingo eyahlukileyo
- C = STM8 SWIM isiqhagamshelanisi ekujoliswe kuko
- Jonga uMfanekiso 12
4.1.3 Imiqondiso ye-SWIM noqhagamshelo
Itheyibhile yesi-2 ishwankathela amagama omqondiso, imisebenzi, kunye nemiqondiso yoqhagamshelwano ekujoliswe kuyo xa usebenzisa intambo yocingo ene-4-pin connector.
Itheyibhile 2. SWIM imidibaniso yeribhoni eflethi ye-ST-LINK/V2
| Inombolo yePin. | Igama | Umsebenzi | Uqhagamshelo ekujoliswe kulo |
| 1 | VDD | I-VCC ekujoliswe kuyo (1) | MCU VCC |
| 2 | IDATHA | QUBHA | Iphini lokuqubha le-MCU |
| 3 | GND | UMHLABA | GND |
| 4 | SETSHENZISWA KHONA | SETSHENZISWA KHONA | MCU RESET pin |
1. Umbane ovela kwibhodi yesicelo uqhagamshelwe kwi-ST-LINK/V2 debugging kunye nebhodi yeprogram ukuqinisekisa ukuhambelana komqondiso phakathi kweebhodi zombini.
Itheyibhile yesi-3 ishwankathela amagama omqondiso, imisebenzi, kunye nemiqondiso yoqhagamshelwano ekujoliswe kuyo kusetyenziswa intambo yeentambo ezahlukeneyo.
Njengoko i-SWIM intambo yocingo oluhlukeneyo luneziqhagamshelo ezizimeleyo kuzo zonke izikhonkwane kwelinye icala, kunokwenzeka ukudibanisa i-ST-LINK / V2-ISOL kwibhodi yesicelo ngaphandle kokudibanisa i-SWIM eqhelekileyo. Kule ribhoni caba, umbala othile kunye neleyibhile ukwenza lula uxhulumaniso kwiireferensi ekujoliswe kuyo yonke imiqondiso.
Itheyibhile 3. I-SWIM yoxhumo lwekhebula oluphantsi kweendleko ze-ST-LINK/V2-ISOL
| Umbala | Igama le-cable pin | Umsebenzi | Uqhagamshelo ekujoliswe kulo |
| Bomvu | TVCC | I-VCC ekujoliswe kuyo (1) | MCU VCC |
| Luhlaza | UART-RX | Engasetyenziswanga | Igciniwe (2) (engaqhagamshelwanga kwibhodi ekujoliswe kuyo) |
| Luhlaza | IUART-TX | ||
| Lubhelu | I-BOOTO | ||
| Orenji | QUBHA | QUBHA | Iphini lokuqubha le-MCU |
| Mnyama | GND | UMHLABA | GND |
| Mhlophe | QUMELA-RST | SETSHENZISWA KHONA | MCU RESET pin |
1. Umbane ovela kwibhodi yesicelo uqhagamshelwe kwi-ST-LINK/V2 debugging kunye nebhodi yeprogram ukuqinisekisa ukuhambelana komqondiso phakathi kweebhodi zombini.
2. I-BOOT0, i-UART-TX, kunye ne-UART-RX zigcinelwe uphuhliso lwexesha elizayo.
I-TVCC, i-SWIM, i-GND, kunye ne-SWIM-RST inokudibaniswa nexabiso eliphantsi le-2.54 mm i-pitch connector okanye ukukhonkxa iintloko ezikhoyo kwibhodi ekujoliswe kuyo.
4.2 Uqhagamshelwano ne-STM32
Ukuphuhliswa kwezicelo ezisekelwe kwi-STM32 microcontrollers, i-ST-LINK/V2 kufuneka iqhagamshelwe kwisicelo usebenzisa i-standard 20-pin J.TAG Iribhoni ecaba inikezelwe.
Itheyibhile yesi-4 ishwankathela amagama omqondiso, imisebenzi, kunye nemiqondiso yoqhagamshelwano ekujoliswe kuyo yomgangatho we-20-pin J.TAG iribhoni ecaba kwi-ST-LINK/V2.
Itheyibhile 5 ishwankathela amagama omqondiso, imisebenzi, kunye neempawu zoqhagamshelwano ekujoliswe kuzo zomgangatho we-20-pin J.TAG iribhoni ecaba kwi-ST-LINK/V2-ISOL.
Uluhlu 4. JTAG/Uqhagamshelwano lwentambo ye-SWD kwi-STLINK-V2
| Iphini Hayi. | ST-LINK/V2 isinxibelelanisi (CN3) | ST-LINKN2 umsebenzi | Uqhagamshelo ekujoliswe kulo (JTAG) | Uqhagamshelo ekujoliswe kulo (SWD) |
| 1 | VAPP | I-VCC ekujoliswe kuyo | MCU VDD(1) | MCU VDD(1) |
| 2 | ||||
| 3 | I-TRST | JTAG I-TRST | NJTRST | I-GND(2) |
| 4 | GND | GND | GNDK3) | I-GND(3) |
| 5 | TDI | JTAG TDO | JTDI | I-GND(2) |
| 6 | GND | GND | I-GND(3) | I-GND(3) |
| 7 | TMS SWDIO | JTAG TMS, SW 10 | JTMS | ISWDIO |
| 8 | GND | GND | I-GND(3) | I-GND(3) |
| 9 | TCK SWCLK | JTAG TCK, SW CLK | JTCK | SWCLK |
| 10 | GND | GND | I-GND(3) | I-GND(3) |
| 11 | Ayidityaniswanga | Ayidityaniswanga | Ayidityaniswanga | Ayidityaniswanga |
| 12 | GND | GND | I-GND(3) | I-GND(3) |
| 13 | TDO SWO | JTAG TDI. SWO | JTDO | TRACESWOO) |
| 14 | GND | GND | I-GND(3) | I-GND(3) |
| 15 | I-NRST | I-NRST | I-NRST | I-NRST |
| 16 | GND | GND | GNDK3) | I-GND(3) |
| 17 | Ayidityaniswanga | Ayidityaniswanga | Ayidityaniswanga | Ayidityaniswanga |
| 18 | GND | GND | I-GND(3) | I-GND(3) |
| 19 | VDD | I-VDD (3.3 V) | Ayidityaniswanga | Ayidityaniswanga |
| 20 | GND | GND | I-GND(3) | I-GND(3) |
- Umbane ovela kwibhodi yesicelo uqhagamshelwe kwi-ST-LINK/V2 debugging kunye nebhodi yeprogram ukuqinisekisa ukuhambelana komqondiso phakathi kweebhodi.
- Qhagamshela kwi-GND yokunciphisa ingxolo kwiribhoni.
- Ubuncinci enye yezi zikhonkwane kufuneka idityaniswe phantsi ukuze iziphathe ngendlela eyiyo. Kucetyiswa ukudibanisa zonke.
- Ngokuzikhethela: Yeyacingo yothotho Viewer (SWV) umkhondo.
Uluhlu 5. JTAG/Uqhagamshelwano lwentambo ye-SWD kwi-STLINK-V2-ISOL
| Inombolo yePin. | ST-LINK/V2 isiqhagamshelanisi (CN3) | ST-LINKN2 umsebenzi | Uqhagamshelwano ekujoliswe kulo (JTAG) | Uqhagamshelo ekujoliswe kulo (SWD) |
| 1 | VAPP | I-VCC ekujoliswe kuyo | MCU VDD(1) | MCU VDD(1) |
| 2 | ||||
| 3 | I-TRST | JTAG I-TRST | NJTRST | I-GND(2) |
| 4 | Ayidityaniswanga | Ayidityaniswanga | Ayidityaniswanga | Ayidityaniswanga |
| 5 | TDI | JTAG TDO | JTDI | I-GND(2) |
| 6 | Ayidityaniswanga | Ayidityaniswanga | Ayidityaniswanga | Ayidityaniswanga |
| 7 | TMS SWDIO | JTAG TMS. SW 10 | JTMS | ISWDIO |
| 8 | Ayidityaniswanga | Ayidityaniswanga | Ayidityaniswanga | Ayidityaniswanga |
| 9 | TCK SWCLK | JTAG TCK, SW CLK | JTCK | SWCLK |
| 10 | Ayisetyenziswa(5) | Ayisetyenziswa(5) | Ayidityaniswanga(5) | Ayidityaniswanga(5) |
| 11 | Ayidityaniswanga | Ayidityaniswanga | Ayidityaniswanga | Ayidityaniswanga |
| 12 | GND | GND | I-GND(3) | I-GND(3) |
| 13 | TDO SWO | JTAG TDI, SWO | JTDO | TRACESW0(4) |
| 14 | Ayisetyenziswa(5) | Ayisetyenziswa(5) | Ayidityaniswanga(5) | Ayidityaniswanga(5) |
| 15 | I-NRST | I-NRST | I-NRST | I-NRST |
| 16 | Ayidityaniswanga | Ayidityaniswanga | Ayidityaniswanga | Ayidityaniswanga |
| 17 | Ayidityaniswanga | Ayidityaniswanga | Ayidityaniswanga | Ayidityaniswanga |
| 18 | GND | GND | I-GND(3) | I-GND(3) |
| 19 | Ayidityaniswanga | Ayidityaniswanga | Ayidityaniswanga | Ayidityaniswanga |
| 20 | GND | GND | I-GND(3) | I-GND(3) |
- Umbane ovela kwibhodi yesicelo uqhagamshelwe kwi-ST-LINK/V2 debugging kunye nebhodi yeprogram ukuqinisekisa ukuhambelana komqondiso phakathi kweebhodi.
- Qhagamshela kwi-GND yokunciphisa ingxolo kwiribhoni.
- Ubuncinci enye yezi zikhonkwane kufuneka idityaniswe phantsi ukuze iziphathe ngendlela eyiyo. Kucetyiswa ukudibanisa zonke.
- Ngokuzikhethela: Yeyacingo yothotho Viewer (SWV) umkhondo.
Uluhlu 5. JTAG/Uqhagamshelwano lwentambo ye-SWD kwi-STLINK-V2-ISOL
| Inombolo yePin. | ST-LINK/V2 isiqhagamshelanisi (CN3) | ST-LINKN2 umsebenzi | Uqhagamshelwano ekujoliswe kulo (JTAG) | Uqhagamshelo ekujoliswe kulo (SWD) |
| 1 | VAPP | I-VCC ekujoliswe kuyo | MCU VDD(1) | MCU VDD(1) |
| 2 | ||||
| 3 | I-TRST | JTAG I-TRST | NJTRST | I-GND(2) |
| 4 | Ayidityaniswanga | Ayidityaniswanga | Ayidityaniswanga | Ayidityaniswanga |
| 5 | TDI | JTAG TDO | JTDI | I-GND(2) |
| 6 | Ayidityaniswanga | Ayidityaniswanga | Ayidityaniswanga | Ayidityaniswanga |
| 7 | TMS SWDIO | JTAG TMS. SW 10 | JTMS | ISWDIO |
| 8 | Ayidityaniswanga | Ayidityaniswanga | Ayidityaniswanga | Ayidityaniswanga |
| 9 | TCK SWCLK | JTAG TCK. SW CLK | JTCK | SWCLK |
| 10 | Ayisetyenziswa(5) | Ayisetyenziswa(5) | Ayidityaniswanga(5) | Ayidityaniswanga(5) |
| 11 | Ayidityaniswanga | Ayidityaniswanga | Ayidityaniswanga | Ayidityaniswanga |
| 12 | GND | GND | I-GND(3) | I-GND(3) |
| 13 | TDO SWO | JTAG TDI. SWO | JTDO | TRACESW0(4) |
| 14 | Ayisetyenziswa(5) | Ayisetyenziswa(5) | Ayidityaniswanga(5) | Ayidityaniswanga(5) |
| 15 | I-NRST | I-NRST | I-NRST | I-NRST |
| 16 | Ayidityaniswanga | Ayidityaniswanga | Ayidityaniswanga | Ayidityaniswanga |
| 17 | Ayidityaniswanga | Ayidityaniswanga | Ayidityaniswanga | Ayidityaniswanga |
| 18 | GND | GND | I-GND(3) | I-GND(3) |
| 19 | Ayidityaniswanga | Ayidityaniswanga | Ayidityaniswanga | Ayidityaniswanga |
| 20 | GND | GND | I-GND(3) | I-GND(3) |
- Umbane ovela kwibhodi yesicelo uqhagamshelwe kwi-ST-LINK/V2 debugging kunye nebhodi yeprogram ukuqinisekisa ukuhambelana komqondiso phakathi kweebhodi.
- Qhagamshela kwi-GND yokunciphisa ingxolo kwiribhoni.
- Ubuncinci enye yezi zikhonkwane kufuneka idityaniswe phantsi ukuze iziphathe ngendlela eyiyo. Kucetyiswa ukudibanisa zonke.
- Ngokuzikhethela: Yeyacingo yothotho Viewer (SWV) umkhondo.
- Isetyenziswe yi-SWIM kwi-ST-LINK/V2-ISOL (jonga kwiThebhile 3).
Umzobo we-9 ubonisa indlela yokudibanisa i-ST-LINK/V2 kwithagethi usebenzisa i-JTAG intambo.
- A = Ibhodi yesicelo ekujoliswe kuyo enoJTAG isinxibelelanisi
- B = JTAG/SWD 20-wire flat cable
- C = STM32 JTAG kunye ne-SWD target connector
Isalathiso somdibaniso ofunekayo kwibhodi yesicelo ekujoliswe kuyo yile: 2x10C header wrapping 2x40C H3 / 9.5 (pitch 2.54) - HED20 SCOTT PHSD80.
Phawula: Ukusetyenziswa kwexabiso eliphantsi, okanye xa umgangatho we-20-pin 2.54 mm-pitch footprint yokudibanisa mkhulu kakhulu, kunokwenzeka ukuphumeza TAG-Qhagamshela isisombululo. I TAG-Ukudibanisa i-adapter kunye nekhebula inikezela ngeendlela ezilula nezithembekileyo zokudibanisa i-ST-LINK/V2 okanye i-ST-LINK/V2ISOL kwi-PCB ngaphandle kokufuna icandelo lokukhwelana kwi-PCB yesicelo.
Ukufumana iinkcukacha ezithe vetshe kwesi sisombululo kunye nesicelo-PCB-ulwazi lweenyawo, tyelela www.tag-Connect.com.
Iimbekiselo zamacandelo ahambelanayo noJTAG kunye nojongano lwe-SWD zezi:
a) I-adapter ye-TC2050-ARM2010 (i-20-pin- ukuya kwi-10-pin-interface yebhodi)
b) TC2050-IDC okanye TC2050-IDC-NL (Akukho milenze) (10-pin cable)
c) TC2050-CLIP egcina ikliphu ukuze isetyenziswe neTC2050-IDC-NL (ukhetho)
4.3 ST-LINK / V2 isimo se-LED
I-LED ebhalwe nge-COM phezulu kwe-ST-LINK/V2 ibonisa isimo se-ST-LINK/V2 (nokuba luhlobo luni loxhulumaniso). Ngeenkcukacha:
- I-LED idanyaza bomvu: ubalo lokuqala lwe-USB kunye nePC luyenzeka
- I-LED ibomvu: unxibelelwano phakathi kwe-PC kunye ne-ST-LINK / V2 isekiwe (isiphelo sobalo)
- I-LED idanyaza eluhlaza / ebomvu: Idatha iyatshintshwa phakathi kwethagethi kunye nePC
- I-LED iluhlaza: unxibelelwano lokugqibela luphumelele
- I-LED i-orange: i-ST-LINK / V2 unxibelelwano kunye nethagethi ayiphumelelanga.
Uqwalaselo lwesoftware
5.1 ST-LINK/V2 uphuculo lwe-firmware
I-ST-LINK/V2 ifakela i-firmware yophuculo lwendlela yokuphucula kwindawo nge-USB port. Njengoko i-firmware inokuvela ngexesha lobomi be-ST-LINK/V2 imveliso (ukusebenza okutsha, ukulungiswa kwe-bug, inkxaso yeentsapho ezintsha ze-microcontroller), kuyacetyiswa ukuba undwendwele amaxesha ngamaxesha amaphepha anikezelweyo www.st.com ukuhlala usexesheni ngenguqulelo yamva nje.
5.2 Uphuhliso lwesicelo se-STM8
Jonga kwi-ST toolset Pack24 ene-patch 1 okanye yakutshanje, equka i-ST Visual Development (STVD) kunye ne-ST Visual Programmer (STVP).
5.3 Uphuhliso lwesicelo se-STM32 kunye nenkqubo ye-flash
Izixhobo zeqela lesithathu (IAR ™ EWARM, Keil ® MDK-ARM ™ ) ixhasa i-ST-LINK/V2 ngokweenguqulelo ezinikwe kwiThebhu le-6 okanye inguqulelo yamva nje ekhoyo.
Itheyibhile 6. Indlela i-toolchains yomntu wesithathu ixhasa ngayo i-ST-LINK/V2
| Iqela lesithathu | Ikhonkco lezixhobo | Inguqulelo |
| IAR™ | EWARM | 6.2 |
| Keil® | MDK-ARM™ | 4.2 |
I-ST-LINK/V2 ifuna umqhubi we-USB ozinikeleyo. Ukuba isethingi yesixhobo ayifaki ngokuzenzekelayo, umqhubi unokufumaneka www.st.com phantsi kwegama STSW-LINK009.
Ngolwazi oluthe kratya malunga nezixhobo zomntu wesithathu, tyelela oku kulandelayo webiindawo:
Amaqhinga
Ibali leenkcazelo zephini:
VDD = Umthamo ekujoliswe kuwotagingqiqo
IDATHA = SWIM DATA umgca phakathi kwethagethi kunye nesixhobo sokulungisa ingxaki
GND = Umthamo womhlabatage
UKUSETHA kwakhona = Ukusetha ngokutsha inkqubo ekujoliswe kuyo
Ibali leenkcazelo zephini:
VDD = Umthamo ekujoliswe kuwotagingqiqo
IDATHA = SWIM DATA umgca phakathi kwethagethi kunye nesixhobo sokulungisa ingxaki
GND = Umthamo womhlabatage
UKUSETHA kwakhona = Ukusetha ngokutsha inkqubo ekujoliswe kuyo
Imbali yohlaziyo
Uluhlu 7. Imbali yohlaziyo loxwebhu
| Umhla | Uhlaziyo | Iinguqu |
| 22-Epr-11 | 1 | Ukukhutshwa kokuqala. |
| 3-Juni-11 | 2 | Itheyibhile 2: I-SWIM yokudityaniswa kweribhoni yeflethi ye-ST-LINK / V2: ukongeza umbhalo osemazantsi we-1 kumsebenzi "I-VCC ekujoliswe kuyo". Uluhlu 4: JTAG/ Ukudibanisa intambo ye-SWD: yongeza umbhalo osemazantsi kumsebenzi "I-VCC ekujoliswe kuyo". Itheyibhile 5: Indlela i-toolchains yomntu wesithathu exhasa ngayo i-ST-LINK/V2: ihlaziywe "iinguqulelo" ze-IAR kunye ne-Keil. |
| 19-Aug-11 | 3 | Kongezwe iinkcukacha zomqhubi we-USB kwiCandelo 5.3. |
| 11-May-12 | 4 | Yongezwe i-SWD kunye ne-SWV ku-JTAG iimpawu zoqhagamshelwano. ULuhlu 4 olulungisiweyo: JTAG/Uqhagamshelwano lweentambo ze-SWD. |
| 13-Sep-12 | 5 | Ikhowudi yeodolo yongeziwe ye-ST-LINKN2-ISOL. ICandelo 4.1 eliHlaziyiweyo: Uphuhliso lwesicelo se-STM8 kwiphepha le-15. Inqaku elongezelelweyo 6 kwiThebhile 4. Inqaku elongeziweyo "Kwizicelo zexabiso eliphantsi ..." phambi kweCandelo 3.3: STLINK/V2 isimo se-LEDs kwiphepha le-14. |
| 18-Oct-12 | 6 | Icandelo elongeziweyo 5.1: ST-LINK/V2 firmware upgrade on page 15. |
| 25-Mar-16 | 7 | Ixabiso leVRMS elihlaziyiweyo kwiNtshayelelo kunye neMiba. |
| 18-Oct-18 | 8 | Itheyibhile ehlaziyiweyo yesi-4: JTAG/Uqhagamshelwano lweentambo zeSWD kunye nemibhalo esemazantsi. Ukuhlelwa okubhaliweyo okuncinci kulo lonke uxwebhu. |
| 9-Jan-23 | 9 | Intshayelelo eHlaziyiweyo, iimpawu, kunye neCandelo 5.3: Uphuhliso lwesicelo se-STM32 kunye nenkqubo ye-flash. Itheyibhile ehlaziyiweyo yesi-5: Indlela izixhobo zesixhobo sesithathu ezixhasa ngayo i-ST-LINK/V2. Ukuhlelwa okubhaliweyo okuncinci kulo lonke uxwebhu. |
| 3-Epr-24 | 10 | Uluhlu lwangaphambili 4 JTAG/Uqhagamshelwano lweentambo zeSWD zahlulwe kwiThebhile 4: JTAG/Uqhagamshelwano lwentambo ye-SWD kwi-STLINK-V2 kunye neThebhile 5: JTAG/Uqhagamshelwano lwentambo ye-SWD kwi-STLINK-V2-ISOL. |
ISAZISO ESIBALULEKILEYO – FUNDA NGOKUQAPHELELEYO
I-STMicroelectronics NV kunye ne-subsidiaries yayo ("ST") inelungelo lokwenza utshintsho, izilungiso, ukuphuculwa, ukuguqulwa, kunye nokuphuculwa kweemveliso ze-ST kunye / okanye kolu xwebhu nangaliphi na ixesha ngaphandle kwesaziso. Abathengi kufuneka bafumane ulwazi lwamva nje olufanelekileyo kwiimveliso ze-ST ngaphambi kokubeka iiodolo. Iimveliso ze-ST zithengiswa ngokuhambelana nemigaqo ye-ST kunye neemeko zokuthengisa kwindawo ngexesha lokuvuma umyalelo. Abathengi banoxanduva kuphela lokhetho, ukhetho, kunye nokusetyenziswa kweemveliso ze-ST kwaye i-ST ayithathi tyala loncedo lwesicelo okanye uyilo lweemveliso zabathengi.
Akukho layisensi, echaziweyo okanye echaziweyo, kulo naliphi na ilungelo lepropathi enomgangatho ophezulu wokuqonda linikezelwa ngu-ST apha.
Ukuthengiswa kwakhona kweemveliso ze-ST ezinamalungiselelo ahlukileyo kulwazi oluchazwe apha kuya kuphelisa nayiphi na iwaranti enikwe yi-ST yaloo mveliso.
I-ST kunye ne-logo ye-ST ziimpawu zorhwebo ze-ST. Ngolwazi olongezelelweyo malunga neempawu zentengiso ze-ST, bhekisa ku www.st.com/trademarks. Zonke ezinye iimveliso okanye amagama eenkonzo ziyipropati yabanini bazo.
Ulwazi olukolu xwebhu luthatha indawo kwaye luthatha indawo yolwazi olwalunikelwe ngaphambili kulo naluphi na uguqulelo lwangaphambili lolu xwebhu.
© 2024 STMicroelectronics – Onke amalungelo agciniwe
Amaxwebhu / Izibonelelo
 |
ST ST-LINK-V2 KwiSekethe yeDebugger Programmer [pdf] Incwadi yokusebenzisa ST-LINK-V2, ST-LINK-V2-ISOL, ST-LINK-V2 KwiSekethe yeDebugger Programmer, ST-LINK-V2, kwiSekethe iDebugger Programmer, iSekethe iDebugger Programmer, iDebugger Programmer |