UM1075
Akwụkwọ ntuziaka onye ọrụ
ST-LINK/V2 in-circuit debugger/programmer
maka STM8 na STM32
Okwu mmalite
ST-LINK/V2 bụ onye na-eme ihe nbibi / ihe mmemme maka STM8 na STM32 microcontrollers. Otu modul interface waya (SWIM) na JTAG/ serial waya debugging (SWD) interfaces na-eme ka nkwurịta okwu na STM8 ma ọ bụ STM32 microcontroller ọ bụla na-arụ ọrụ na bọọdụ ngwa.
Na mgbakwunye na ịnye otu ọrụ nke ST-LINK/V2, ST-LINK/V2-ISOL na-egosipụta ikewapụ dijitalụ n'etiti PC na bọọdụ ngwa ebumnuche. Ọ na-eguzogide voltages nke ruru 1000 V RMS.
USB zuru-ọsọ interface na-enyere nkwurịta okwu na PC na:
- Ngwa STM8 site na ST Visual Develop (STVD) ma ọ bụ ST Visual Programme (STVP) sọftụwia (dị na STMicroelectronics)
- Ngwa STM32 site na IAR™, Keil®, STM32CubeIDE, STM32CubeProgrammer na STM32CubeMonitor agbakwunyere gburugburu mmepe.
Atụmatụ
- Ike 5V na-eweta site na njikọ USB
- USB 2.0 zuru-ọsọ dakọtara interface
- Ọkọlọtọ USB-A ruo Obere-B eriri
- Atụmatụ SWIM akọwapụtara
– 1.65 ruo 5.5 V ngwa voltage kwadoro na interface SWIM
– SWIM ụdị ọsọ dị ala na nke dị elu na-akwado
- Ọnụego mmemme SWIM: 9.7 na 12.8 Kbytes / s, n'otu n'otu, maka obere na oke ọsọ
- eriri SWIM maka njikọ na ngwa site na njikọ ERNI ọkọlọtọ vetikal (ref: 284697 ma ọ bụ 214017) ma ọ bụ kehoraizin (ntụgharị: 214012) njikọ
- eriri SWIM maka njikọ na ngwa site na isi ntụtụ ma ọ bụ njikọ pitch 2.54 mm - JTAG/SWD (Serial Wire Debug) atụmatụ akọwapụtara
– 1.65 ruo 3.6 V ngwa voltage kwadoro na JTAG/ SWD interface yana ntinye nnabata 5V (a)
– JTAG eriri maka njikọ na ọkọlọtọ JTAG 20-pin pitch 2.54 mm njikọ
- Na-akwado JTAG nkwukọrịta, ruo 9 MHz (ndabara: 1.125 MHz)
- Na-akwado debug waya (SWD) ruo 4 MHz (ndabere: 1.8 MHz), yana waya serial viewnzikọrịta ozi er (SWV), ruo 2 MHz - A na-akwado atụmatụ mmelite firmware ozugbo (DFU)
- Ọnọdụ LED, na-egbuke egbuke n'oge nkwurịta okwu na PC
- 1000 V RMS elu iche voltage (ST-LINK/V2-ISOL naanị)
- Okpomọkụ na-arụ ọrụ site na 0 ruo 50 Celsius
Ịtụ ozi
Iji tụọ ST-LINK/V2, rụtụ aka na Tab le 1.
Tebụl 1. Ndepụta nke koodu iwu
| Koodu ịtụ | Nkọwa nke ST-LINK |
| ST-LINK/V2 | Onye nbibi/mmemme mmemme |
| ST-LINK/V2-ISOL | Onye na-eme ihe nbibi / onye mmemme nwere ikewapụ dijitalụ |
a. ST-LINK/V2 nwere ike ịkparịta ụka na ebumnuche ndị na-arụ ọrụ n'okpuru 3.3 V mana ọ na-ewepụta akara ngosi na volta a.tage larịị. Ebumnuche STM32 na-anabata oke oke atage. Ọ bụrụ na ụfọdụ akụkụ ndị ọzọ nke bọọdụ ebumnuche nwere ezi uche, jiri ST-LINK/V2-ISOL, STLINK-V3MINIE, ma ọ bụ STLINK-V3SET nwere ihe nkwụnye B-STLINK-VOLT iji zere mmetụta nke overvol.tage injection na osisi.
Ngwaahịa ọdịnaya
E gosipụtara eriri ndị a napụtara n'ime ngwaahịa a na foto 2 na eserese 3. Ha gụnyere (site n'aka ekpe gaa n'aka nri):
- Ọkọlọtọ USB-A ruo Obere-B USB (A)
- ST-LINK/V2 debugging na mmemme (B)
- Njikọ SWIM dị ọnụ ala (C)
- rịbọn dị larịị SWIM nwere njikọ ERNI ọkọlọtọ n'otu akụkụ (D)
- JTAG ma ọ bụ SWD na SWV flat ribbon nwere njikọ 20-pin (E)
Nhazi ngwaike
Emebere ST-LINK/V2 gburugburu ngwaọrụ STM32F103C8, nke gụnyere Arm ®(a) Cortex® na-arụ ọrụ dị elu.
-M3 isi. Ọ dị na ngwugwu TQFP48.
Dị ka egosiri na foto 4, ST-LINK/V2 na-enye njikọ abụọ:
- Njikọ STM32 maka JTAG/ SWD na SWV interface
- Njikọ STM8 maka interface SWIM
ST-LINK/V2-ISOL na-enye otu njikọ maka STM8 SWIM, STM32 J.TAG/ SWD, na SWV interfaces.
- A = STM32 JTAG na njikọ SWD target
- B = STM8 SWIM njikọ ebumnuche
- C = STM8 SWIM, STM32 JTAG, na SWD lekwasịrị anya njikọ
- D = LED ọrụ nkwukọrịta
4.1 Njikọ na STM8
Maka mmepe nke ngwa dabere na STM8 microcontrollers, ST-LINK/V2 nwere ike jikọọ na bọọdụ lekwasịrị anya site na eriri abụọ dị iche iche, dabere na njikọ dị na bọọdụ ngwa.
Ndị a cables bụ:
- Ribọn dị larịị SWIM nwere njikọ ERNI ọkọlọtọ n'otu nsọtụ
- Igwe SWIM nwere njikọ 4-pin abụọ, 2.54 mm ma ọ bụ eriri waya dị iche iche SWIM
4.1.1 Ọkọlọtọ ERNI njikọ na SWIM flat ribbon
Ọgụgụ 5 na-egosi ka esi jikọọ ST-LINK/V2 ma ọ bụrụ na njikọ ERNI 4-pin SWIM ọkọlọtọ dị na bọọdụ ngwa.
- A = bọọdụ ngwa ebumnuche nwere njikọ ERNI
- B = eriri waya nwere njikọ ERNI n'otu nsọtụ
- C = STM8 SWIM njikọ ebumnuche
- Lee eserese 11
Ọgụgụ 6 na-egosi na pin 16 na-efu na njikọ ST-LINK/V2-ISOL. A na-eji pin a na-efu efu dị ka igodo nchekwa na njikọ eriri, iji kwenye ọnọdụ ziri ezi nke eriri SWIM na njikọ ebumnuche ọbụlagodi ntụtụ ejiri ma SWIM na J.TAG eriri.
4.1.2 Njikọ SWIM dị ọnụ ala
Ọgụgụ 7 na-egosi otu esi ejikọ ST-LINK/V2 ma ọ bụrụ na njikọ SWIM 4-pin, 2.54 mm dị ọnụ ala dị na bọọdụ ngwa.
- A = bọọdụ ngwa ebumnuche nwere 4-pin, 2.54 mm, njikọ dị ọnụ ala
- B = eriri waya nwere njikọ 4-pin ma ọ bụ eriri waya dị iche
- C = STM8 SWIM njikọ ebumnuche
- Lee eserese 12
4.1.3 mgbama SWIM na njikọ
Tab le 2 na-achịkọta aha mgbama, ọrụ, na mgbama njikọ ebumnuche mgbe ị na-eji eriri waya nwere njikọ 4-pin.
Tebụl 2. Njikọ rịbọn dị larịị SWIM maka ST-LINK/V2
| Ntụtụ ọ dịghị. | Aha | Ọrụ | Njikọ ebumnuche |
| 1 | VDD | Ebumnuche VCC(1) | MCU VCC |
| 2 | DATA | Igwu mmiri | MCU SWIM pin |
| 3 | GND | GALA | GND |
| 4 | Tụgharịa | Tụgharịa | MCU tọgharịa pin |
1. A na-ejikọta ọkụ eletrik sitere na bọọdụ ngwa na ST-LINK / V2 debugging na mmemme mmemme iji hụ na ndakọrịta mgbaàmà n'etiti mbadamba abụọ ahụ.
Tab le 3 na-achịkọta aha mgbama, ọrụ, na mgbama njikọ ebumnuche n'iji eriri waya dị iche iche.
Dị ka eriri SWIM iche-waya nwere njikọ kwụụrụ onwe maka ntụtụ niile n'otu akụkụ, ọ ga-ekwe omume ijikọ ST-LINK/V2-ISOL na bọọdụ ngwa na-enweghị ọkọlọtọ SWIM njikọ. N'elu rịbọn a dị larịị, otu agba na akara iji mee ka njikọ dị mfe na-ezo aka na akara niile.
Tebụl 3. Njikọ eriri SWIM dị ọnụ ala maka ST-LINK/V2-ISOL
| Agba | Aha eriri USB | Ọrụ | Njikọ ebumnuche |
| Uhie | TVCC | Ebumnuche VCC(1) | MCU VCC |
| Akwụkwọ ndụ akwụkwọ ndụ | UART-RX | Ejighi ya | Echekwara (2) (anaghị ejikọrọ na bọọdụ ebumnuche) |
| Acha anụnụ anụnụ | UART-TX | ||
| Odo | BOOTO | ||
| oroma | Igwu mmiri | Igwu mmiri | MCU SWIM pin |
| Nwa | GND | GALA | GND |
| Ọcha | SWIM-RST | Tụgharịa | MCU tọgharịa pin |
1. A na-ejikọta ọkụ eletrik sitere na bọọdụ ngwa na ST-LINK / V2 debugging na mmemme mmemme iji hụ na ndakọrịta mgbaàmà n'etiti mbadamba abụọ ahụ.
2. BOOT0, UART-TX, na UART-RX ka edobere maka mmepe n'ọdịnihu.
Enwere ike ijikọ TVCC, SWIM, GND na SWIM-RST na njikọ pitch 2.54 mm dị ọnụ ala ma ọ bụ tinye nkụnye eji isi mee dị na bọọdụ ebumnuche.
4.2 Njikọ na STM32
Maka mmepe nke ngwa dabere na STM32 microcontrollers, ST-LINK/V2 ga-ejikọta ya na ngwa site na iji ọkọlọtọ 20-pin J.TAG Enyere rịbọn dị larịị.
Tab le 4 na-achịkọta aha mgbama, ọrụ, na mgbama njikọ ebumnuche nke ọkọlọtọ 20-pin J.TAG rịbọn dị larịị na ST-LINK/V2.
Tebụl 5 na-achịkọta aha mgbama, ọrụ, na akara njikọ ebumnuche nke ọkọlọtọ 20-pin J.TAG rịbọn dị larịị na ST-LINK/V2-ISOL.
Isiokwu 4. JTAG/ Njikọ eriri SWD na STLINK-V2
| Ntụtụ mba. | ST-LINK/V2 njikọ (CN3) | ST-LINKN2 ọrụ | Njikọ ebumnuche (JTAG) | Njikọ ebumnuche (SWD) |
| 1 | VAPP | Ebumnuche VCC | MCU VDD(1) | MCU VDD(1) |
| 2 | ||||
| 3 | TRST | JTAG TRST | NJTRST | GND(2) |
| 4 | GND | GND | GNDK3) | GND(3) |
| 5 | TDI | JTAG TDO | JTDI | GND(2) |
| 6 | GND | GND | GND(3) | GND(3) |
| 7 | TMS SWDIO | JTAG TMS, SW 10 | JTMS | SWDIO |
| 8 | GND | GND | GND(3) | GND(3) |
| 9 | TCK SWCLK | JTAG TCK, SW CLK | JTCK | SWCLK |
| 10 | GND | GND | GND(3) | GND(3) |
| 11 | Ejikọtaghị ya | Ejikọtaghị ya | Ejikọtaghị ya | Ejikọtaghị ya |
| 12 | GND | GND | GND(3) | GND(3) |
| 13 | TDO SWO | JTAG TDI. SWO | JTDO | TRACESWOO) |
| 14 | GND | GND | GND(3) | GND(3) |
| 15 | NRST | NRST | NRST | NRST |
| 16 | GND | GND | GNDK3) | GND(3) |
| 17 | Ejikọtaghị ya | Ejikọtaghị ya | Ejikọtaghị ya | Ejikọtaghị ya |
| 18 | GND | GND | GND(3) | GND(3) |
| 19 | VDD | VDD (3.3V) | Ejikọtaghị ya | Ejikọtaghị ya |
| 20 | GND | GND | GND(3) | GND(3) |
- A na-ejikọta ọkụ ọkụ sitere na bọọdụ ngwa na ST-LINK / V2 debugging na mmemme mmemme iji hụ na ndakọrịta mgbaàmà n'etiti bọọdụ.
- Jikọọ na GND maka mbelata mkpọtụ na rịbọn.
- Opekempe, otu n'ime ntụtụ ndị a ga-ejikọrịrị na ala maka omume ziri ezi. A na-atụ aro ka ijikọ ha niile.
- Nhọrọ: Maka Oghere Usoro Waya Viewer (SWV) akara.
Isiokwu 5. JTAG/ Njikọ eriri SWD na STLINK-V2-ISOL
| Ntụtụ ọ dịghị. | Njikọ ST-LINK/V2 (CN3) | ST-LINKN2 ọrụ | Njikọ ebumnuche (JTAG) | Njikọ ebumnuche (SWD) |
| 1 | VAPP | Ebumnuche VCC | MCU VDD(1) | MCU VDD(1) |
| 2 | ||||
| 3 | TRST | JTAG TRST | NJTRST | GND(2) |
| 4 | Ejikọtaghị ya | Ejikọtaghị ya | Ejikọtaghị ya | Ejikọtaghị ya |
| 5 | TDI | JTAG TDO | JTDI | GND(2) |
| 6 | Ejikọtaghị ya | Ejikọtaghị ya | Ejikọtaghị ya | Ejikọtaghị ya |
| 7 | TMS SWDIO | JTAG TMS. SW 10 | JTMS | SWDIO |
| 8 | Ejikọtaghị ya | Ejikọtaghị ya | Ejikọtaghị ya | Ejikọtaghị ya |
| 9 | TCK SWCLK | JTAG TCK, SW CLK | JTCK | SWCLK |
| 10 | Ejighị ya (5) | Ejighị ya (5) | Enweghị njikọ (5) | Enweghị njikọ (5) |
| 11 | Ejikọtaghị ya | Ejikọtaghị ya | Ejikọtaghị ya | Ejikọtaghị ya |
| 12 | GND | GND | GND(3) | GND(3) |
| 13 | TDO SWO | JTAG TDI, SWO | JTDO | TRACESW0(4) |
| 14 | Ejighị ya (5) | Ejighị ya (5) | Enweghị njikọ (5) | Enweghị njikọ (5) |
| 15 | NRST | NRST | NRST | NRST |
| 16 | Ejikọtaghị ya | Ejikọtaghị ya | Ejikọtaghị ya | Ejikọtaghị ya |
| 17 | Ejikọtaghị ya | Ejikọtaghị ya | Ejikọtaghị ya | Ejikọtaghị ya |
| 18 | GND | GND | GND(3) | GND(3) |
| 19 | Ejikọtaghị ya | Ejikọtaghị ya | Ejikọtaghị ya | Ejikọtaghị ya |
| 20 | GND | GND | GND(3) | GND(3) |
- A na-ejikọta ọkụ ọkụ sitere na bọọdụ ngwa na ST-LINK / V2 debugging na mmemme mmemme iji hụ na ndakọrịta mgbaàmà n'etiti bọọdụ.
- Jikọọ na GND maka mbelata mkpọtụ na rịbọn.
- Opekempe, otu n'ime ntụtụ ndị a ga-ejikọrịrị na ala maka omume ziri ezi. A na-atụ aro ka ijikọ ha niile.
- Nhọrọ: Maka Oghere Usoro Waya Viewer (SWV) akara.
Isiokwu 5. JTAG/ Njikọ eriri SWD na STLINK-V2-ISOL
| Ntụtụ ọ dịghị. | Njikọ ST-LINK/V2 (CN3) | ST-LINKN2 ọrụ | Njikọ ebumnuche (JTAG) | Njikọ ebumnuche (SWD) |
| 1 | VAPP | Ebumnuche VCC | MCU VDD(1) | MCU VDD(1) |
| 2 | ||||
| 3 | TRST | JTAG TRST | NJTRST | GND(2) |
| 4 | Ejikọtaghị ya | Ejikọtaghị ya | Ejikọtaghị ya | Ejikọtaghị ya |
| 5 | TDI | JTAG TDO | JTDI | GND(2) |
| 6 | Ejikọtaghị ya | Ejikọtaghị ya | Ejikọtaghị ya | Ejikọtaghị ya |
| 7 | TMS SWDIO | JTAG TMS. SW 10 | JTMS | SWDIO |
| 8 | Ejikọtaghị ya | Ejikọtaghị ya | Ejikọtaghị ya | Ejikọtaghị ya |
| 9 | TCK SWCLK | JTAG TCK. SW CLK | JTCK | SWCLK |
| 10 | Ejighị ya (5) | Ejighị ya (5) | Enweghị njikọ (5) | Enweghị njikọ (5) |
| 11 | Ejikọtaghị ya | Ejikọtaghị ya | Ejikọtaghị ya | Ejikọtaghị ya |
| 12 | GND | GND | GND(3) | GND(3) |
| 13 | TDO SWO | JTAG TDI. SWO | JTDO | TRACESW0(4) |
| 14 | Ejighị ya (5) | Ejighị ya (5) | Enweghị njikọ (5) | Enweghị njikọ (5) |
| 15 | NRST | NRST | NRST | NRST |
| 16 | Ejikọtaghị ya | Ejikọtaghị ya | Ejikọtaghị ya | Ejikọtaghị ya |
| 17 | Ejikọtaghị ya | Ejikọtaghị ya | Ejikọtaghị ya | Ejikọtaghị ya |
| 18 | GND | GND | GND(3) | GND(3) |
| 19 | Ejikọtaghị ya | Ejikọtaghị ya | Ejikọtaghị ya | Ejikọtaghị ya |
| 20 | GND | GND | GND(3) | GND(3) |
- A na-ejikọta ọkụ ọkụ sitere na bọọdụ ngwa na ST-LINK / V2 debugging na mmemme mmemme iji hụ na ndakọrịta mgbaàmà n'etiti bọọdụ.
- Jikọọ na GND maka mbelata mkpọtụ na rịbọn.
- Opekempe, otu n'ime ntụtụ ndị a ga-ejikọrịrị na ala maka omume ziri ezi. A na-atụ aro ka ijikọ ha niile.
- Nhọrọ: Maka Oghere Usoro Waya Viewer (SWV) akara.
- Eji SWIM na ST-LINK/V2-ISOL (lee Tebụl 3).
Ọgụgụ 9 na-egosi otu esi ejikọ ST-LINK/V2 na ebumnuche iji JTAG eriri.
- A = Bọdụ ngwa ebumnuche na JTAG njikọ
- B = JTAG/ SWD 20-waya flat cable
- C = STM32 JTAG na njikọ SWD target
Ntụaka nke njikọ achọrọ na bọọdụ ngwa ebumnuche bụ: 2x10C nkụnye eji isi mee 2x40C H3/9.5 (pitch 2.54) - HED20 SCOTT PHSD80.
Mara: Maka ngwa dị ọnụ ala, ma ọ bụ mgbe akara ukwu njikọ 20-pin 2.54 mm-pitch dị oke oke, ọ ga-ekwe omume itinye ya. TAG-njikọ ngwọta. Nke TAG-Connect nkwụnye na USB na-enye ụzọ dị mfe na a pụrụ ịdabere na ya iji jikọọ ST-LINK/V2 ma ọ bụ ST-LINK/V2ISOL na PCB na-enweghị chọrọ a mating akụrụngwa na ngwa PCB.
Maka nkọwa ndị ọzọ gbasara azịza a na ozi-PCB-ụkwụ, gaa na www.tag-njikọ.com.
Ntụaka nke components dakọtara na JTAG na interface SWD bụ:
a) TC2050-ARM2010 nkwụnye (20-pin-na 10-pin-interface board)
b) TC2050-IDC ma ọ bụ TC2050-IDC-NL (Ọ dịghị ụkwụ) (10-pin USB)
c) TC2050-CLIP clip maka ojiji ya na TC2050-IDC-NL (nhọrọ)
4.3 ST-LINK/V2 ọnọdụ LED
Ikanam akpọrọ COM n'elu ST-LINK/V2 na-egosi ọnọdụ ST-LINK/V2 (ihe ọ bụla ụdị njikọ ahụ). Na nkowa:
- Ikanam na-egbuke egbuke na-acha uhie uhie: ọnụọgụ USB mbụ na PC na-eme
- Ikanam na-acha ọbara ọbara: e guzobere nkwurịta okwu n'etiti PC na ST-LINK / V2 (njedebe nke nchịkọta)
- The LED blinks green/red: A na-agbanwe data n'etiti ebumnuche na PC
- LED bụ akwụkwọ ndụ akwụkwọ ndụ: nkwurịta okwu ikpeazụ enweela nke ọma
- Ikanam bụ oroma: ST-LINK/V2 nzikọrịta ozi na ebumnuche adaala.
Nhazi ngwanrọ
5.1 ST-LINK/V2 firmware nkwalite
ST-LINK/V2 na-etinye usoro nkwalite ngwa ngwa maka nkwalite ebe site na ọdụ ụgbọ mmiri USB. Dị ka firmware nwere ike ịmalite n'oge ndụ nke ngwaahịa ST-LINK/V2 (ọrụ ọhụrụ, ndozi ahụhụ, nkwado maka ezinụlọ microcontroller ọhụrụ), a na-atụ aro ka ị gaa na ibe ndị raara onwe ha nye na. www.st.com ka ị na-enwe ọhụụ na ụdị kachasị ọhụrụ.
5.2 STM8 mmepe ngwa
Rụtụ aka na ST toolset Pack24 nwere patch 1 ma ọ bụ karịa nso nso a, nke gụnyere ST Visual Develop (STVD) na ST Visual Programmer (STVP).
5.3 STM32 mmepe ngwa na mmemme flash
Ngwá ọrụ ndị ọzọ (IAR ™ EWARM, Keil ® MDK-ARM ™ ) na-akwado ST-LINK/V2 dịka ụdị enyere na Tab le 6 ma ọ bụ ụdị kachasị ọhụrụ dị.
Tebụl 6. Olee otú ngwá ọrụ ndị ọzọ na-akwado ST-LINK/V2
| Onye nke atọ | Toolchain | Ụdị |
| IAR™ | EWARM | 6.2 |
| Keil® | MDK-ARM™ | 4.2 |
ST-LINK/V2 chọrọ onye ọkwọ ụgbọ ala raara onwe ya nye. Ọ bụrụ na ntọala ngwaọrụ anaghị etinye ya na akpaghị aka, enwere ike ịhụ onye ọkwọ ụgbọ ala na ya www.st.com n'okpuru aha STSW-LINK009.
Maka ozi ndị ọzọ gbasara ngwaọrụ ndị ọzọ, gaa na ndị a websaịtị:
Atụmatụ
Akụkọ ifo maka nkọwa pin:
VDD = Target voltage uche
DATA = ahịrị SWIM DATA n'etiti ebumnuche na ngwa nbipu
GND = Ala voltage
Tọgharia = Tọgharia usoro ebumnuche
Akụkọ ifo maka nkọwa pin:
VDD = Target voltage uche
DATA = ahịrị SWIM DATA n'etiti ebumnuche na ngwa nbipu
GND = Ala voltage
Tọgharia = Tọgharia usoro ebumnuche
Akụkọ ngbanwe
Tebụl 7. Akụkọ ndegharị akwụkwọ
| Ụbọchị | Ndozigharị | Mgbanwe |
| 22-Eprel-11 | 1 | Ntọhapụ mbụ. |
| 3-June-11 | 2 | Tebụl 2: Njikọ rịbọn dị larịị SWIM maka ST-LINK/V2: agbakwunyere ihe odide ala ala peeji 1 na ọrụ "Target VCC". Isiokwu 4: JTAG/ Njikọ eriri SWD: gbakwunyere ndetu ala ala na ọrụ "Target VCC". Tebụl 5: Otu ụdị ngwá ọrụ ndị ọzọ na-akwado ST-LINK/V2: emelitere "ụdị" nke IAR na Keil. |
| 19-Ọgọst-11 | 3 | agbakwunyere nkọwa ọkwọ ụgbọ ala USB na ngalaba 5.3. |
| 11- Mee-12 | 4 | Etinyere SWD na SWV na JTAG njirimara njikọ. Agbanwere Tebụl 4: JTAG/ SWD njikọ eriri. |
| 13-Sep-12 | 5 | Agbakwunyere koodu ịtụ ST-LINKN2-ISOL. Nkebi 4.1 emelitere: Mmepe ngwa STM8 na ibe 15. Agbakwunyere ndetu 6 na Tebụl 4. Ihe mgbakwunye agbakwunyere “Maka ngwa ndị dị ọnụ ala…” tupu ngalaba 3.3: STLINK/V2 ọkwa LEDs na ibe 14. |
| 18-Ọkt-12 | 6 | Nkebi 5.1 agbakwunyere: nkwalite ngwa ngwa ST-LINK/V2 na ibe 15. |
| 25-Mar-16 | 7 | Uru VRMS emelitere na mbido na atụmatụ. |
| 18-Ọkt-18 | 8 | Emelitere Tebụl 4: JTAG/ Njikọ eriri SWD na ndetu ala ala ya. Ndozi obere ederede n'ofe akwụkwọ niile. |
| 9-Jen-23 | 9 | Okwu mmalite, atụmatụ, na ngalaba 5.3 emelitere: Mmepe ngwa STM32 na mmemme flash. Tebụl 5 emelitere: Otu chains ngwaọrụ ndị ọzọ na-akwado ST-LINK/V2. Ndozi obere ederede n'ofe akwụkwọ niile. |
| 3-Eprel-24 | 10 | Isiokwu gara aga 4 JTAG/ Njikọ eriri SWD kewara na Tebụl 4: JTAG/ Njikọ eriri SWD na STLINK-V2 na tebụl 5: JTAG/ Njikọ eriri SWD na STLINK-V2-ISOL. |
ỌMỤMỤ dị mkpa – Gụọ nke ọma
STMicroelectronics NV na ndị enyemaka ya (“ST”) debere ikike ime mgbanwe, ndozi, nkwalite, mgbanwe na nkwalite ngwaahịa ST na/ma ọ bụ akwụkwọ a n'oge ọ bụla na-enweghị ọkwa. Ndị na-azụ ahịa kwesịrị ịnweta ozi kacha ọhụrụ dị mkpa na ngwaahịa ST tupu ha etinye iwu. A na-ere ngwaahịa ST dabere na usoro na ọnọdụ ọrịre nke ST n'oge nnabata. Ndị na-azụ ahịa bụ naanị maka nhọrọ, nhọrọ, na ojiji nke ngwaahịa ST yana ST anaghị ewere ụgwọ ọ bụla maka enyemaka ngwa ma ọ bụ imepụta ngwaahịa ndị zụrụ ya.
Enweghị ikike, ekwupụtara ma ọ bụ egosipụtara, ikike ikike ọgụgụ isi ọ bụla nke ST nyere n'ime ebe a.
Mweghachi nke ngwaahịa ST nwere ndokwa dị iche na ozi e depụtara n'ime ya ga-emebi akwụkwọ ikike ọ bụla ST nyere maka ụdị ngwaahịa a.
ST na akara ST bụ ụghalaahịa nke ST. Maka ozi ndị ọzọ gbasara ụghalaahịa ST, rụtụ aka www.st.com/trademarks. Ngwaahịa ma ọ bụ aha ọrụ ndị ọzọ bụ ihe onwunwe nke ndị nwe ha.
Ozi dị n'ime akwụkwọ a nọchiri ma dochie ozi enyere na mbụ na ụdị akwụkwọ a mbụ.
© 2024 STMicroelectronics – Ikike niile echekwabara
Akwụkwọ / akụrụngwa
 |
ST ST-LINK-V2 Na Circuit Debugger Programmer [pdf] Akwụkwọ ntuziaka onye ọrụ ST-LINK-V2, ST-LINK-V2-ISOL, ST-LINK-V2 Na Circuit Debugger Programmer, ST-LINK-V2, Na Circuit Debugger Programmer, Circuit Debugger Programmer, Debugger Programmer |