Halo Static Single Sided Fixed
Height Workstation Frame
Buka ea Tataiso
Likarolo tsa likarolo
| NO. | Lebitso la Karolo | PCS |
| 1 | Tafole maoto | 2 |
| 2 | Kholomo( ka ho le letona) | 1 |
| 3 | Bolt: M6x12 | 5 |
| 4 | Screw: ST4x20 | 22 |
| 5 | Masakana a mahlakoreng | 2 |
| 6 | Moqomo oa Rubber | 14 |
| 7 | Foreimi e ka holimo-1 | 1 |
| 8 | Bolt: M6x10 | 3 |
| 9 | Bracket e bohareng | 1 |
| 10 | Litšepe tse bohareng | 2 |
| 11 | Foreimi e ka holimo-2 | 1 |
| 12 | Column( left) | 1 |
| 13 | Allen Wrench (4mm) | 1 |
| 14 | Allen Wrench (5mm) | 1 |
| 15 | Thae ea Cable | 5 |
Litaelo tsa Kopano
Mohato oa 1
Loosen the pre-installed bolts and adjust the length of the top frame to match the size of the table top.
Mohato oa 2
Insert the Column to the top frame, fix the lifting column with 4pcs of screws M6x12 like.
Mohato oa 3
Place the table feet on the Column and rotate it to align, then tighten the pre-installed bolt.
Mohato oa 4
Beha sekhahla se lehlakoreng holim'a foreimi e ka holimo 'me u tiise liboutu.
Mohato oa 5
Mount the tabletop and fix it with 14 pcs screws ST4x20;
Fix the centre bracket with 2 pcs of screws M6x10
Tighten the pre-installed bolts on the top frame
Ho kenya terei ea thapo
Mohato oa 1
– Fix the cable tray (B2-SSCT ) to the cable tray arms (HP-SSARM) with 8 pcs M6x10 screws.
Mohato oa 2
- Kenya li-brackets tsa U ho foreime ea deske ka li-screw tse 4 tsa M8x10.
- Beha terei ea thapo ho foreime ea deske ebe u e lokisa ka li-screws tse 6 tsa M6x10
Ho kenya liphanele tsa skrine ( Skrine ea Lekunutu ea Shush30 )
Mohato oa 1
– Insert the tapped plates to the screen panel ( plates can be found in the B2-SBRAC carton )
Mohato oa 2
– Install the screen brackets (B2-SBRAC) to the Shush30 Extrusion with 8 pcs M5x6 screws.
Mohato oa 3
– Fix the screen brackets (B2-SBRAC) to the desk frame with 10 pcs M6x10 screws.
EPS (900mm H Eco Panel) Screen panel installation
Mohato oa 1
– Install the screen brackets (B2-SBRAC) on the cable tray arm (HP-SSARM)with 10 PCS M6x10 Screws. The direction as the photos display.
Mohato oa 2
- Beha karolo ea EPS holim'a masakaneng a skrineng
Using a 6mm drill bit ( not included ), drill out holes in the Eco Panel Screen in line with the back-to-back screen bracket holes ( Note: Carbide Drill Bits Work Best For PET panel )
– Place 8 x Double Ended Bolts M5* 32mm – 6mm through the screen bracket ( B2-SBRAC ) holes and the holes you have created in the Eco Panel Screen. Tighten the double-ended bolt with the Allen key.
Litokomane / Lisebelisoa
 |
Rapidline Static Single Sided Fixed Height Workstation Frame [pdf] Buka ea Taelo Static Single Sided Fixed Height Workstation Frame, Single Sided Fixed Height Workstation Frame, Sided Fixed Height Workstation Frame, Fixed Height Workstation Frame, Height Workstation Frame, Workstation Frame, Frame |