Static Single Sided Fixed Height Workstation Frame
“
Product Information
Specifications:
- Frame Type: Static Single Sided Fixed Height Workstation
- Components Included: Table feet, Column (right), Bolt: M6x12,
Screw: ST4x20, Side brackets, Rubber pad, Top frame-1, Bolt: M6x10,
Centre bracket, Center rails, Top frame-2, Column (left), Allen
Wrench (4mm), Allen Wrench (5mm), Cable Tie
Product Usage Instructions
Assembly Instructions:
- Loosen the pre-installed bolts and adjust the length of the top
frame to match the size of the table top. - Insert the Column to the top frame, fix lifting column with
4pcs screws M6x12. - Place the table feet on the Column and rotate it to align, then
tighten the pre-installed bolt. - Place the side bracket on the top frame and tighten the
bolts. - Mount the tabletop and fix it with 14 pcs screws ST4x20; Fix
the centre bracket with 2 pcs screws M6x10. Tighten the
pre-installed bolts on the top frame.
Cable Tray Installation:
- Fix the cable tray (B2-SSCT) to the cable tray arms (HP-SSARM)
with 8 pcs M6x10 screws. - Install the U brackets to the desk frame with 4 pcs M8x10
screws. - Mount the cable tray to the desk frame and fix it with 6 pcs
M6x10 screws.
Screen Panel Installation (Shush30 Privacy Screen):
- Insert the tapped plates to the screen panel (plates can be
found in B2-SBRAC carton). - Install the screen brackets (B2-SBRAC) to the Shush30 Extrusion
with 8 pcs M5x6 screws. - Fix the screen brackets (B2-SBRAC) to the desk frame with 10
pcs M6x10 screws.
EPS (900mm H Eco Panel) Screen Panel Installation:
- Install the screen brackets (B2-SBRAC) on the cable tray arm
(HP-SSARM) with 10 PCS M6x10 Screws. The brackets direction as
photos display. - Place the EPS panel on the screen brackets. Using a 6mm drill
bit (not included), drill out holes in Eco Panel Screen in line
with back-to-back screen bracket holes. Place 8 x Double Ended
Bolts M5*32mm – 6mm through The screen bracket (B2-SBRAC) holes and
the holes you have created in the Eco Panel Screen. Tighten
double-ended bolt with Allen key.
Frequently Asked Questions (FAQ)
Q: How do I adjust the height of the workstation frame?
A: The height of the workstation frame is fixed and cannot be
adjusted.
Q: Can I use this workstation frame for a standing desk
setup?
A: This workstation frame is not designed for a standing desk
setup as it has a fixed height.
“`
Halo Static Single Sided Fixed Height Workstation Frame Instruction Manual
1
Component parts
NO. Component Name
PCS
NO. Component Name
PCS
1
Table feet
2
9
Centre bracket
1
2
Column( right)
1
10 Center rails
2
3
Bolt: M6x12
5
11 Top frame-2
1
4
Screw:ST4x20
22
12 Column( left)
1
5
Side brackets
2
13 Allen Wrench(4mm)
1
6
Rubber pad
14
14 Allen Wrench(5mm)
1
7
Top frame-1
1
15 Cable Tie
5
8
Bolt: M6x10
3
2
Assembly Instructions
Step 1 Loosen the pre-installed bolts and Adjust the length of the top frame to match the size of the table top.
Step 2 Inset the Column to the top frame,fix lifting column with 4pcs screws M6x12 like.
3
Step 3 Place the table feet on the Column and rotate it and make it align, then tighten the pre-installed bolt.
Step 4 Place the side bracket on the top frame and tighten the bolts.
4
Step 5 Mount the tabletop and fix it with 14 pcs screws ST4x20; Fix the centre bracket with 2 pcs screws M6x10 Tighten the pre-installed bolts on the top fame
5
Cable tray installation Step 1 – Fix the cable tray(B2-SSCT ) to the cable tray arms(HP-SSARM) with 8 pcs M6x10 screws.
Step 2 – Install the U brackets to the desk frame with 4 pcs M8x10 screws. – Mount the cable tray to the desk frame and fix it with 6 pcs M6x10 screws
6
Screen panel installation ( Shush30 Privacy Screen ) Step 1 – Insert the tapped plates to the screen panel ( plates can be found in B2-SBRAC carton )
Step 2 – Install the screen brackets ( B2-SBRAC )to the Shush30 Extrusion with 8 pcs M5x6 screws.
7
Step 3 – Fix the screen brackets ( B2-SBRAC ) to the desk frame with 10 pcs M6x10 screws.
8
EPS ( 900mm H Eco Panel ) Screen panel installation Step 1 – Install the screen brackets(B2-SBRAC) on the cable tray arm (HP-SSARM)with 10 PCS M6x10 Screws
The brackets direction as photos display.
Step 2 – Place the EPS panel on the screen brackets Using a 6mm drill bit ( not included ), drill out holes in Eco Panel Screen in line with back to back screen bracket holes ( Note: Carbide Drill Bits Work Best For PET panel ) – Place 8 x Double Ended Bolts M5* 32mm – 6mm through The screen bracket ( B2-SBRAC ) holes and the holes you have created in the Eco Panel Screen. Tighten double ended bolt with Allen key.
9
10
Documents / Resources
 |
Rapidline Static Single Sided Fixed Height Workstation Frame [pdf] Instruction Manual Static Single Sided Fixed Height Workstation Frame, Single Sided Fixed Height Workstation Frame, Sided Fixed Height Workstation Frame, Fixed Height Workstation Frame, Height Workstation Frame, Workstation Frame, Frame |