Halo Static Single Sided Fixed
Hæð Workstation Frame
Leiðbeiningarhandbók
Íhlutir
| NEI. | Heiti hluta | PCS |
| 1 | Borðfætur | 2 |
| 2 | Dálkur (hægri) | 1 |
| 3 | Bolti: M6x12 | 5 |
| 4 | Skrúfa: ST4x20 | 22 |
| 5 | Hliðarfestingar | 2 |
| 6 | Gúmmípúði | 14 |
| 7 | Efsti rammi-1 | 1 |
| 8 | Bolti: M6x10 | 3 |
| 9 | Miðfesting | 1 |
| 10 | Miðstaðir | 2 |
| 11 | Efsti rammi-2 | 1 |
| 12 | Column( left) | 1 |
| 13 | Allen skiptilykill (4mm) | 1 |
| 14 | Allen skiptilykill (5mm) | 1 |
| 15 | Kaðlaband | 5 |
Samsetningarleiðbeiningar
Skref 1
Loosen the pre-installed bolts and adjust the length of the top frame to match the size of the table top.
Skref 2
Insert the Column to the top frame, fix the lifting column with 4pcs of screws M6x12 like.
Skref 3
Place the table feet on the Column and rotate it to align, then tighten the pre-installed bolt.
Skref 4
Setjið hliðarfestinguna á efri rammann og herðið boltana.
Skref 5
Mount the tabletop and fix it with 14 pcs screws ST4x20;
Fix the centre bracket with 2 pcs of screws M6x10
Tighten the pre-installed bolts on the top frame
Uppsetning kapalbakka
Skref 1
– Fix the cable tray (B2-SSCT ) to the cable tray arms (HP-SSARM) with 8 pcs M6x10 screws.
Skref 2
– Settu U-festingarnar á skrifborðsgrindina með 4 stk M8x10 skrúfum.
– Festu kapalbakkann við skrifborðsgrindina og festu hana með 6 stk M6x10 skrúfum
Uppsetning á skjáborði (Shush30 friðhelgisskjár)
Skref 1
– Insert the tapped plates to the screen panel ( plates can be found in the B2-SBRAC carton )
Skref 2
– Install the screen brackets (B2-SBRAC) to the Shush30 Extrusion with 8 pcs M5x6 screws.
Skref 3
– Fix the screen brackets (B2-SBRAC) to the desk frame with 10 pcs M6x10 screws.
EPS (900mm H Eco Panel) Screen panel installation
Skref 1
– Install the screen brackets (B2-SBRAC) on the cable tray arm (HP-SSARM)with 10 PCS M6x10 Screws. The direction as the photos display.
Skref 2
– Setjið EPS spjaldið á skjáfestingarnar
Using a 6mm drill bit ( not included ), drill out holes in the Eco Panel Screen in line with the back-to-back screen bracket holes ( Note: Carbide Drill Bits Work Best For PET panel )
– Place 8 x Double Ended Bolts M5* 32mm – 6mm through the screen bracket ( B2-SBRAC ) holes and the holes you have created in the Eco Panel Screen. Tighten the double-ended bolt with the Allen key.
Skjöl / auðlindir
 |
Rapidline Static Single Sided Fixed Height Workstation Frame [pdfLeiðbeiningarhandbók Static Single Sided Fixed Height Workstation Frame, Single Sided Fixed Height Workstation Frame, Sided Fixed Height Workstation Frame, Fixed Height Workstation Frame, Height Workstation Frame, Workstation Frame, Frame |