Halo Static Single Sided Fixed
Výška rámu pracovní stanice
Návod k použití
Součásti
| ŽÁDNÝ. | Název součásti | PCS |
| 1 | Nohy stolu | 2 |
| 2 | sloupec (vpravo) | 1 |
| 3 | Šroub: M6x12 | 5 |
| 4 | Šroub: ST4x20 | 22 |
| 5 | Boční držáky | 2 |
| 6 | Gumová podložka | 14 |
| 7 | Horní rám-1 | 1 |
| 8 | Šroub: M6x10 | 3 |
| 9 | Středová konzola | 1 |
| 10 | Středové kolejnice | 2 |
| 11 | Horní rám-2 | 1 |
| 12 | Column( left) | 1 |
| 13 | Imbusový klíč (4 mm) | 1 |
| 14 | Imbusový klíč (5 mm) | 1 |
| 15 | Stahovací páska | 5 |
Montážní návod
Krok 1
Loosen the pre-installed bolts and adjust the length of the top frame to match the size of the table top.
Krok 2
Insert the Column to the top frame, fix the lifting column with 4pcs of screws M6x12 like.
Krok 3
Place the table feet on the Column and rotate it to align, then tighten the pre-installed bolt.
Krok 4
Umístěte boční držák na horní rám a utáhněte šrouby.
Krok 5
Mount the tabletop and fix it with 14 pcs screws ST4x20;
Fix the centre bracket with 2 pcs of screws M6x10
Tighten the pre-installed bolts on the top frame
Instalace kabelového žlabu
Krok 1
– Fix the cable tray (B2-SSCT ) to the cable tray arms (HP-SSARM) with 8 pcs M6x10 screws.
Krok 2
– Namontujte U držáky na rám stolu pomocí 4 šroubů M8x10.
– Kabelový žlab namontujte na rám stolu a upevněte jej 6 ks šroubů M6x10
Instalace obrazovkového panelu (ochrana soukromí Shush30)
Krok 1
– Insert the tapped plates to the screen panel ( plates can be found in the B2-SBRAC carton )
Krok 2
– Install the screen brackets (B2-SBRAC) to the Shush30 Extrusion with 8 pcs M5x6 screws.
Krok 3
– Fix the screen brackets (B2-SBRAC) to the desk frame with 10 pcs M6x10 screws.
EPS (900mm H Eco Panel) Screen panel installation
Krok 1
– Install the screen brackets (B2-SBRAC) on the cable tray arm (HP-SSARM)with 10 PCS M6x10 Screws. The direction as the photos display.
Krok 2
– Umístěte EPS panel na držáky obrazovky
Using a 6mm drill bit ( not included ), drill out holes in the Eco Panel Screen in line with the back-to-back screen bracket holes ( Note: Carbide Drill Bits Work Best For PET panel )
– Place 8 x Double Ended Bolts M5* 32mm – 6mm through the screen bracket ( B2-SBRAC ) holes and the holes you have created in the Eco Panel Screen. Tighten the double-ended bolt with the Allen key.
Dokumenty / zdroje
 |
Rapidline Static Single Sided Fixed Height Workstation Frame [pdfNávod k obsluze Static Single Sided Fixed Height Workstation Frame, Single Sided Fixed Height Workstation Frame, Sided Fixed Height Workstation Frame, Fixed Height Workstation Frame, Height Workstation Frame, Workstation Frame, Frame |