Halo Static Single Sided Fixed
د لوړ کاري سټیشن چوکاټ
د لارښوونې لارښود
د اجزاو برخې
| نه. | د برخې نوم | PCS |
| 1 | د میز پښو | 2 |
| 2 | کالم (ښي) | 1 |
| 3 | بولټ: M6x12 | 5 |
| 4 | سکرو: ST4x20 | 22 |
| 5 | د غاړې قوسونه | 2 |
| 6 | د ربړ پیډ | 14 |
| 7 | پورته چوکاټ-1 | 1 |
| 8 | بولټ: M6x10 | 3 |
| 9 | مرکز بریکٹ | 1 |
| 10 | د مرکز ریلونه | 2 |
| 11 | پورته چوکاټ-2 | 1 |
| 12 | Column( left) | 1 |
| 13 | الن رنچ (4 ملي متر) | 1 |
| 14 | الن رنچ (5 ملي متر) | 1 |
| 15 | کیبل ټی | 5 |
د مجلس لارښوونې
1 ګام
Loosen the pre-installed bolts and adjust the length of the top frame to match the size of the table top.
2 ګام
Insert the Column to the top frame, fix the lifting column with 4pcs of screws M6x12 like.
3 ګام
Place the table feet on the Column and rotate it to align, then tighten the pre-installed bolt.
4 ګام
د غاړې بریکٹ په پورتنۍ چوکاټ کې ځای په ځای کړئ او بولټونه ټینګ کړئ.
5 ګام
Mount the tabletop and fix it with 14 pcs screws ST4x20;
Fix the centre bracket with 2 pcs of screws M6x10
Tighten the pre-installed bolts on the top frame
د کیبل ټری نصب
1 ګام
– Fix the cable tray (B2-SSCT ) to the cable tray arms (HP-SSARM) with 8 pcs M6x10 screws.
2 ګام
- د میز چوکاټ کې U بریکٹونه د 4 pcs M8x10 پیچونو سره نصب کړئ.
- د کیبل ټری د میز چوکاټ ته واچوئ او د 6 pcs M6x10 پیچونو سره یې تنظیم کړئ
د سکرین پینل نصب کول ( Shush30 د محرمیت سکرین )
1 ګام
– Insert the tapped plates to the screen panel ( plates can be found in the B2-SBRAC carton )
2 ګام
– Install the screen brackets (B2-SBRAC) to the Shush30 Extrusion with 8 pcs M5x6 screws.
3 ګام
– Fix the screen brackets (B2-SBRAC) to the desk frame with 10 pcs M6x10 screws.
EPS (900mm H Eco Panel) Screen panel installation
1 ګام
– Install the screen brackets (B2-SBRAC) on the cable tray arm (HP-SSARM)with 10 PCS M6x10 Screws. The direction as the photos display.
2 ګام
- د EPS پینل د سکرین په قوسونو کې ځای په ځای کړئ.
Using a 6mm drill bit ( not included ), drill out holes in the Eco Panel Screen in line with the back-to-back screen bracket holes ( Note: Carbide Drill Bits Work Best For PET panel )
– Place 8 x Double Ended Bolts M5* 32mm – 6mm through the screen bracket ( B2-SBRAC ) holes and the holes you have created in the Eco Panel Screen. Tighten the double-ended bolt with the Allen key.
اسناد / سرچینې
 |
Rapidline Static Single Sided Fixed Height Workstation Frame [pdf] د لارښوونې لارښود Static Single Sided Fixed Height Workstation Frame, Single Sided Fixed Height Workstation Frame, Sided Fixed Height Workstation Frame, Fixed Height Workstation Frame, Height Workstation Frame, Workstation Frame, Frame |