Halo Static Single Sided Fixed
Wotè Workstation Frame
Manyèl Enstriksyon
Pati konpozan
| NON. | Non eleman | PCS |
| 1 | Pye tab | 2 |
| 2 | Kolòn (adwat) | 1 |
| 3 | Boulon: M6x12 | 5 |
| 4 | Vis: ST4x20 | 22 |
| 5 | Parantèz bò | 2 |
| 6 | Pad an kawoutchou | 14 |
| 7 | Top ankadreman-1 | 1 |
| 8 | Boulon: M6x10 | 3 |
| 9 | Sant parantèz | 1 |
| 10 | Sant ray yo | 2 |
| 11 | Top ankadreman-2 | 1 |
| 12 | Column( left) | 1 |
| 13 | Allen kle (4mm) | 1 |
| 14 | Allen kle (5mm) | 1 |
| 15 | Mare kab | 5 |
Enstriksyon Asanble
Etap 1
Desere boulon ki te deja enstale yo epi ajiste longè ankadreman anlè a pou l koresponn ak gwosè tèt tab la.
Etap 2
Insert the Column to the top frame, fix the lifting column with 4pcs of screws M6x12 like.
Etap 3
Place the table feet on the Column and rotate it to align, then tighten the pre-installed bolt.
Etap 4
Mete sipò bò a sou ankadreman anlè a epi sere boulon yo.
Etap 5
Monte tèt tab la epi fikse l ak 14 vis ST4x20;
Fix the centre bracket with 2 pcs of screws M6x10
Tighten the pre-installed bolts on the top frame
Enstalasyon plato kab
Etap 1
– Fix the cable tray (B2-SSCT ) to the cable tray arms (HP-SSARM) with 8 pcs M6x10 screws.
Etap 2
– Enstale parantèz U yo nan ankadreman biwo a ak 4 pcs M8x10 vis.
– Monte plato kab la sou ankadreman biwo a epi ranje li ak 6 pcs vis M6x10
Enstalasyon panèl ekran (Shush30 Privacy Screen)
Etap 1
– Insert the tapped plates to the screen panel ( plates can be found in the B2-SBRAC carton )
Etap 2
– Install the screen brackets (B2-SBRAC) to the Shush30 Extrusion with 8 pcs M5x6 screws.
Etap 3
– Fix the screen brackets (B2-SBRAC) to the desk frame with 10 pcs M6x10 screws.
EPS (900mm H Eco Panel) Screen panel installation
Etap 1
– Install the screen brackets (B2-SBRAC) on the cable tray arm (HP-SSARM)with 10 PCS M6x10 Screws. The direction as the photos display.
Etap 2
– Mete panèl EPS la sou sipò ekran yo
Using a 6mm drill bit ( not included ), drill out holes in the Eco Panel Screen in line with the back-to-back screen bracket holes ( Note: Carbide Drill Bits Work Best For PET panel )
– Place 8 x Double Ended Bolts M5* 32mm – 6mm through the screen bracket ( B2-SBRAC ) holes and the holes you have created in the Eco Panel Screen. Tighten the double-ended bolt with the Allen key.
Dokiman / Resous
 |
Rapidline Static Single Sided Fixed Height Workstation Frame [pdfManyèl Enstriksyon Static Single Sided Fixed Height Workstation Frame, Single Sided Fixed Height Workstation Frame, Sided Fixed Height Workstation Frame, Fixed Height Workstation Frame, Height Workstation Frame, Workstation Frame, Frame |