INTELLIFLO® VSF
LEBELO LE PHAPANG LE PUMP E PHAPANGKETSO LE
MOEKETSI MOSEBETSI

LITAELO TSA BOHLOKOA TSA BOPHELO BALA 'ME U LATELLE LITAELO TSOHLE BOLOKA LITAELO TSENA

TLHOKOMELISO EA BOHLOKOA LE LITAELO TSA BOPHELO

BOHLOKOA TSEBISO
Tataiso ena e fana ka litaelo tsa ho kenya le ho sebetsa bakeng sa pompo ena.
Ikopanye le Pentair ka lipotso leha e le life mabapi le thepa ena.
Tlhokomeliso Sehlomathisi: Tataiso ena e na le lintlha tsa bohlokoa mabapi le ho kenya, ts'ebetso le ts'ebeliso e bolokehileng ea sehlahisoa sena. Tlhahisoleseding ena e lokela ho fuoa mong'a le / kapa moetsi oa thepa ena ka mor'a ho kenya kapa ho siuoa holim'a pompo kapa haufi le eona.
Tlhokomeliso: Bukana ena e na le lintlha tsa bohlokoa tse tla u thusa ho sebetsa le ho boloka sehlahisoa sena. Ka kopo e boloke bakeng sa tšebeliso ea nako e tlang.
BALA LE HO LATELA LITAELO TSOHLE BOLOKA LITAELO TSENA
Lena ke letšoao la tlhokomeliso ea polokeho. Ha u bona letšoao lena tsamaisong ea hau kapa bukeng ena, sheba le leng la mantsoe a matšoao a latelang 'me u hlokomele monyetla oa ho tsoa kotsi.
E lemosa ka likotsi tse ka bakang lefu, kotsi e tebileng ea botho, kapa tšenyo e khōlō ea thepa haeba e hlokomolohuoa.
E lemosa ka likotsi tse ka ’nang tsa baka lefu, kotsi e tebileng ea botho, kapa tšenyo e khōlō ea thepa haeba e hlokomolohuoa.
E lemosa ka likotsi tse ka 'nang tsa baka kotsi e nyane kapa tsa baka tšenyo e nyane ea thepa haeba li hlokomolohuoa.
ELA HLOKO E bontša litaelo tse khethehileng tse sa amaneng le likotsi.
Bala ka hloko 'me u latele litaelo tsohle tsa polokeho bukeng ena le lisebelisoa. Boloka mangolo a tšireletso a le boemong bo botle; nkela sebaka haeba e lahlehile kapa e senyehile.
Ha o kenya le ho sebelisa sesebelisoa sena sa motlakase, mehato ea ts'ireletso ea mantlha e lokela ho lateloa kamehla, e kenyellelitse tse latelang:
HO HLOLEHWA HO LATELA LITAELO LE LITEMOSO TSOHLE HO KA BALA TSAMAISO E MPELENG KAPA LEFU. PUMP ENA E TSHWANETSE HO KEnywa LE HO SEBEDISWA FEELA KE MOKGWA E MONG WA TSHEBELETSO YA LETWA A SEBELETSENG. BAHLOLI, BASEBETSI LE BENG BA LETAO LOKELA HO BALA LITEMOSO TSENA LE LITAELO TSOHLE TSA MOR'A BUKANA PELE HO SEBELISA PUMP ENA. LITLHAHISO TSENA LE MANUKATSO EA MOHAPI LI TŠOARA HO SELISWA LE MONONG WA LETIMO.
Se lumelle bana ho sebelisa sehlahisoa sena.
KOTSI TŠOHO MOTLATSI. Hokela feela lepotolohong la lekala le sirelelitsoeng ke ground-fault circuit- interrupter (GFCI). Ikopanye le ramotlakase ea tšoanelehang haeba o sa khone ho netefatsa hore potoloho e sirelelitsoe ke GFCI.
Yuniti ena e tlameha ho hokahana feela le potoloho ea phepelo e sirelelitsoeng ke "ground-fault circuit-interrupter" (GFCI). GFCI e joalo e lokela ho fanoa ke motho ea kenyang 'me e lokela ho lekoa ka mokhoa o tloaelehileng. Ho leka GFCI, tobetsa konopo ea teko. GFCI e lokela ho emisa matla. Tobetsa konopo ea reset. Matla a tlameha ho khutlisoa.
Haeba GFCI e hloleha ho sebetsa ka tsela ena, GFCI e na le phoso. Haeba GFCI e sitisa matla ho pompo ntle le konopo ea teko e phunyeletsoeng, ho phalla fatše ho phalla, ho bontšang monyetla oa ho ts'oaroa ha motlakase. Se ke oa sebelisa pompo ena. Hakolla pompo 'me u etse hore bothata bo lokisoe ke moemeli oa litšebeletso ea tšoanelehang pele u sebelisa.
Pompo ena e sebelisoa le matamo a ho sesa a sa feleng 'me e ka boela ea sebelisoa le libate tse chesang le li-spas haeba li tšoailoe. U se ke ua sebelisa le matamo a polokelo. Letamo le kentsoeng ka ho sa feleng le hahoa fatše kapa fatše kapa mohahong hoo e ke keng ea qhaqha habonolo bakeng sa polokelo. Letamo le bolokehang le hahiloe e le hore le khone ho qhaqhoa habonolo hore le bolokoe 'me le boele le boele le be boemong bo botle ba lona ba pele.
Litemoso tse Akaretsang

• Le ka mohla u se ke ua bula bokahare ba sebaka sa koloi ea koloi. Ho na le banka ea capacitor e bolokang tefiso ea 230 VAC leha ho se na matla yuniti.
• Pompo ha e kenelle metsing.
• Pompo e khona ho phalla ka lebelo le phahameng; sebelisa tlhokomeliso ha u kenya le ho etsa mananeo ho fokotsa bokhoni ba ts'ebetso ea lipompo ka lisebelisoa tsa khale kapa tse belaetsang.
• Litlhoko tsa khoutu bakeng sa ho hokela motlakase li fapana ho ea ka linaha, naha le naha, hammoho le bomasepala ba lehae. Kenya lisebelisoa ho latela Khoutu ea Naha ea Motlakase le likhoutu le melaoana eohle e sebetsang ea lehae.
• Pele o sebeletsa pompo; switjha TIMA matla ho pompo ka ho hakolla potoloho e kholo ho pompo.
• Sesebelisoa sena ha sea rereloa ho sebelisoa ke batho (ho kenyeletsoa le bana) ba nang le matla a fokotsehileng a 'mele, kutlo kapa kelello, kapa ho hloka boiphihlelo le tsebo, ntle le haeba ba filoe tlhokomelo kapa taelo mabapi le tšebeliso ea sesebelisoa ke motho ea ikarabellang bakeng sa polokeho ea bona. .

KOTSI EA HO KHETHOA: LULA HO TŠOA TŠEBELETSO EA KHOLO 'me U HOLE LE LITŠOANTŠISO TSOHLE TSA HO KHETHA! PUMP ENA HA E TLAMETSOE KA SIRELETSO EA TS'IRELETSO EA TŠIRELETSO EA VACUUM (SVRS) 'me HA E SIRELETSO KAROLO EA MMELE KAPA MAONO LE MAONO, TSE HLAHANG (HA MOTHO A LUMELA LETENG LE LETJOA LE SEHLOHONENG KAPA LE SA KHIROHANG).PUMP ENA E HLAHISA MAEMO A PHAHAMENG A MOHAPI MME E HLAHISA VACUUM E MATLA THAKENG EA MOHOLO BOTLASENG BA 'MELE OA METSI. KHANO ENA E MATLA HAHOLO HORE E KA TLOA BATHO BA BATHO KAPA BANA KA TLAS'A METSI HAEBA BA TLA HAUFI LE LEKELETSO KAPA SEKOAHELO SA LEHOLO LE LETLEHO KAPA LE SEROBELENG KAPA TSOHLE.
TŠEBELETSO EA LIK'IRELETSO TSE SA DUMELLANG KAPA HO SEBELISA LETIMO KAPA SPA HA LIKOARO TSE FELENG, HO PHAHAMA KAPA HO ROBEHILE LI KA BAKA HO TLAMEHA 'MLE KAPA MATSOHO, HO TSOA TSOA MORIRI, HO KENYA MELE, HO NTŠOA LE/GOTSA LEFU.
Ho huloa ha drain kapa ho tsoa ho ka baka:
Ho Koaheloa ke Matsoho: Ha leoto le ka monngoa kapa le kenngoa ka lesobeng le bakang ho tlama kapa ho ruruha. Kotsi ena e teng ha sekoaelo sa drainage se le sieo, se robehile, se hlephile, se phatlohile kapa se sa tiisetsoa hantle.
Ho Koaheloa ha Moriri: Ha moriri o hoholeha kapa mafito sekoahelong sa drain, ho tšoasa ea sesang ka tlas'a metsi. Kotsi ena e teng ha tekanyo ea phallo ea sekoahelo e le nyane haholo bakeng sa pompo kapa lipompo.
'Mele Entrapment: Ha karolo ea' mele e ts'oaroa khahlano le sekoaelo sa drain ho tšoasa motho ea sesang ka tlas'a metsi. Kotsi ena e teng ha sekoaelo sa drainage se le sieo, se robehile kapa sekhahla sa phallo ea sekoaelo se sa lekana bakeng sa pompo kapa lipompo.
Evisceration/Disembowelment: Ha motho a dutse hodima letamo le bulehileng (haholo-holo ngwana wa letamo) kapa sebaka sa spa le ho monya ho sebediswa ka ho toba mala, ho baka tshenyo e matla ya mala. Kotsi ena e teng ha sekoaelo sa drain se le sieo, se hlephile, se phatlohile, kapa se sa tiisetsoa hantle.
Mechanical Entrapment: Ha mabenyane, liaparo tsa ho sesa, mekhabiso ea moriri, monoana, monoana oa maoto kapa monoana li tšoaroa ka lekhalong la phallo kapa sekoahelo sa drain. Kotsi ena e teng ha sekoaelo sa drainage se le sieo, se robehile, se hlephile, se phatlohile, kapa se sa tiisetsoa hantle.
HLOKOMELA: SUCTION PLUMBING TSOHLE E TSHWANETSE HO KEnywa HO LAPELA LE DIKHOUTU, MELAO LE DITAELO TSA MORAO-rao-TSA NAHA LE LEEAE.
HO FOKOTŠA KOTSI EA KHOTSO E BAKENG SA TSA KOTSI EA HO KENA HO KENA:

• Sekoaelo se kentsoeng hantle le se sirelelitsoeng sa ANSI/ASME A112.19.8 se amohetsoeng sa ho monya antientrapment se tlameha ho sebelisoa bakeng sa drain ka 'ngoe.
• Sekoahelo se seng le se seng sa ho monya se tlameha ho kengoa bonyane maoto a mararo (3') ho arohana, joalo ka ha ho lekanngoa ho tloha sebakeng se haufi ho ea sebakeng se haufi.
• Kamehla hlahloba likoahelo tsohle bakeng sa mapetsong, tšenyo le boemo ba leholimo bo tsoetseng pele.
• Haeba sekoahelo se hlephile, se petsohile, se senyehile, se robehile kapa se le sieo, tlosa sekoahelo se nepahetseng se tiisitsoeng.
• Fetola likoahelo tsa drain ha ho hlokahala. Likoahelo tsa metsi li senyeha ha nako e ntse e ea ka lebaka la khanya ea letsatsi le boemo ba leholimo.
• Qoba ho ba le moriri, matsoho kapa 'mele haufi le sekoaelo leha e le sefe sa ho monya, mokelikeli oa letamo kapa sekoti.
• Tlosa li- suction outlets kapa u lokise bocha li-inlets tse khutlisang.

Pompo e ka hlahisa maemo a phahameng a ho huloa ka har'a lehlakore la ho hula la tsamaiso ea lipeipi. Maemo ana a phahameng a ho hula a ka baka kotsi haeba motho a ka fihla haufi le masoba a ho hulang. Motho a ka tsoa kotsi e mpe haholo ke sekheo sena se phahameng haholo kapa a ka qabelloa le ho khangoa ke metsi. Ho bohlokoa haholo hore ho kenngoe lipeipi tsa metsi ho latela melaoana ea morao-rao ea naha le ea lehae bakeng sa matamo a ho sesa.
Sesebelisoa sa ho tima pompo se ngotsoeng ka ho hlaka bakeng sa pompo se tlameha ho ba sebakeng se fumanehang habonolo, se hlakileng. Etsa bonnete ba hore basebelisi ba tseba moo e leng teng le hore na ba ka e sebelisa joang maemong a tšohanyetso.
Virginia Graeme Baker (VGB) Pool and Spa Safety Act e theha litlhoko tse ncha bakeng sa beng le basebetsi ba matamo a ho sesa a khoebo le li-spa.
Matamo a khoebo kapa li-spas tse hahiloeng ka la 19 Tšitoe 2008 kapa ka morao ho tsona, li tla sebelisa:
(A) Sisteme e mengata e kholo ea ho hula metsi ntle le bokhoni ba ho itšehla thajana e nang le likoahelo tsa ho hula tse kopanang le ASME/ANSI A112.19.8a Suction Fittings bakeng sa Tšebeliso ea Matamo a ho Swimming, Wading Pools, Spas, le Hot Tubs le tse ling:
(i) Seboka sa polokeho ea vacuum release system (SVRS) ASME/ANSI A112.19.17 Manufactured Safety Vacuum Release systems (SVRS) for Residential and Commercial Swimming Pool, Spa, Hot Tub, le Wading Pool Suction Systems le/kapa ASTM F2387 Standard Specifications bakeng sa Sistimi ea Phatlalatso e Khōlō ea Tšireletseho (SVRS) bakeng sa matamo a ho Sesa, Li-spa le Li-Tubs tse chesang kapa
(ii) Mokhoa o hlophisitsoeng hantle le o lekiloeng oa ho suction-limiting system kapa
(iii) Mochine oa ho tima pompo o itšebetsang.
Matamo a khoebo le li-spas tse hahiloeng pele ho la 19 Tšitoe, 2008, tse nang le metsi a metsi a le mong li tla sebelisa sekoaelo sa ho monya se kopanang le ASME/ANSI A112.19.8a le tse ling:
(A) Kopano ea SVRS ASME/ANSI A112.19.17 le/kapa ASTM F2387, kapa
(B) Sistimi e etselitsoeng hantle le e lekiloeng ea ho suction-limiting vent, kapa
(C) Mokhoa o ikemetseng oa ho koala pompo, kapa
(D) Libaka tse nang le bokooa tse koahetsoeng ke metsi, kapa
(E) Libaka tsa ho hula li tla hlophisoa bocha hore e be li-inlets tse khutlisang.
Bakeng sa ho Kenya Litaolo tsa Motlakase Pateng ea Thepa (Li-switches tsa HO ON/OFF, Li-Timer le Setsi sa Meroalo ea Motlakase)
Kenya lilaoli tsohle tsa motlakase sebakeng sa lisebelisoa, joalo ka li-switches, li-timers, le litsamaiso tsa taolo, joalo-joalo ho lumella ts'ebetso (ho qala, ho koala, kapa ho fana ka litšebeletso) ha pompo efe kapa efe kapa sefe hore mosebelisi a se ke a beha karolo efe kapa efe. 'mele oa hae holim'a kapa haufi le sekoahelo se sefang pompo, sekoaelo sa sefe kapa se koaletsoeng.
Kenyelletso ena e lokela ho lumella mosebelisi sebaka se lekaneng sa ho ema ntle le sefe kapa pompo nakong ea ho qala sistimi, ho koala kapa ho sebeletsa sefefo sa sistimi.
KHATELLO E KOTSI: Ema U HLOKA PUMP LE SEFELA NAKONG EA HO QALA.
Mekhoa ea ho potoloha e sebetsa tlas'a khatello e phahameng. Ha karolo leha e le efe ea tsamaiso ea potoloho (ke hore selikalikoe sa ho notlela, pompo, sefe, li-valve, joalo-joalo) se sebetsoa, ​​moea o ka kena ka har'a sistimi ebe oa hatelloa. Moea o hatelletsoeng o ka etsa hore sekoaelo sa ntlo ea pompo, sekoaelo sa sefe, le li-valve li arohane ka mabifi, e leng se ka bakang kotsi e mpe ea motho kapa lefu. Sekoaelo sa tanka ea sefella le sekhurumetso se sefang li tlameha ho ts'ireletsoa hantle ho thibela karohano e mabifi. Emella hole le lisebelisoa tsohle tsa tsamaiso ea potoloho ha u bulela kapa u qala pompo.
Pele u sebeletsa lisebelisoa, ela hloko khatello ea filthara. Etsa bonnete ba hore litsamaiso tsohle li behiloe ho netefatsa hore sistimi e ke ke ea qala ka phoso nakong ea ts'ebeletso.
Tlosa matla ohle ho pompo. BOHLOKOA: Beha valve ea liphallelo tsa moea sebakeng se bulehileng 'me u emele hore khatello eohle ea tsamaiso e imolohe.
Pele o qala tsamaiso, bula ka botlalo valve ea liphallelo tsa moea 'me u behe li-valve tsohle tsa tsamaiso sebakeng se "bulehileng" ho lumella metsi ho phalla ka bolokolohi ho tloha tanka le ho khutlela tanka. Ema hole le lisebelisoa tsohle ebe u qala pompo.
BOHLOKOA: U se ke ua koala valve ea moea ea filthara ho fihlela khatello eohle e tsoa ho valve 'me ho hlaha metsi a tsitsitseng. Ela hloko tekanyo ea khatello ea sefa 'me u netefatse hore ha e phahame ho feta boemo ba pele ho ts'ebeletso.
Tlhahisoleseding e Akaretsang ea Tlhophiso

• Mosebetsi oohle o tlameha ho etsoa ke setsebi sa litšebeletso tse tšoanelehang, 'me o tlameha ho ikamahanya le likhoutu tsohle tsa naha, tsa naha le tsa lehae.
• Kenya ho fana ka drainage ea lekareche bakeng sa likarolo tsa motlakase.
• Litaelo tsena li na le tlhahisoleseling bakeng sa mefuta e fapaneng ea pompo, ka hona, litaelo tse ling li kanna tsa se sebetse ho mofuta o itseng. Mefuta eohle e reretsoe ho sebelisoa lits'ebetsong tsa letamo la ho sesa. Pompo e tla sebetsa ka nepo feela haeba e lekana hantle le sesebelisoa se ikhethileng mme e kentsoe hantle.

Lipompo tsa boholo bo sa lokelang kapa tse kentsoeng kapa tse sebelisoang lits'ebetsong tse ling ntle le tseo pompo e neng e reretsoe tsona li ka baka kotsi e mpe ea motho kapa lefu. Likotsi tsena li ka kenyelletsa empa li sa felle feela ho ts'oenyeho ea motlakase, mollo, likhohola, ho ts'oaroa ha metsi kapa kotsi e matla kapa tšenyo ea thepa e bakiloeng ke ho hloleha ha sebopeho sa pompo kapa karolo e 'ngoe ea sistimi.
Lipompo le li-motor tse ncha tse lebelo le le leng (1) Kakaretso ea HP kapa ho feta li ke ke tsa rekisoa, tsa rekisoa, kapa tsa kengoa letamong la bolulo bakeng sa tšebeliso ea tlhoekiso California, Karolo ea 20 CCR 1601-1609.
TŠEBELETSO EA BAKENGI / TŠEHETSO EA MOSEBETSI
Haeba u na le lipotso mabapi le ho odara likarolo tse ncha tsa Penair le lihlahisoa tsa letamo, ka kopo ikopanye le:
Tšebeletso ea bareki le Tšehetso ea Tekheniki, USA
(8 AM ho 4:30 PM - Eastern / Pacific Times)
Mohala: 800-831-7133
Fax: 800-284-4151
Web sebaka
Etela www.penair.com bakeng sa tlhahisoleseling mabapi le lihlahisoa tsa Penair.*
Sanford, North Carolina (8 AM ho 4:30 PM ET)
Mohala: 919-566-8000
Fax: 919-566-8920
Moorpark, California (8 AM ho 4:30 PM PT)
Mohala: 805-553-5000 (Ext. 5591)
Fax: 805-553-5515

POMELA KHOTHAVIEW

IntelliFlo® VSF Variable Speed ​​le Flow Pump e ka hlophisoa hore e tsamaee ka lebelo kapa lebelo la phallo e sa khaotseng ka linako tse behiloeng bakeng sa ts'ebetso e phahameng ea ts'ebetso le ho boloka matla bakeng sa matamo a fapaneng a ka tlas'a lefatše.

• Pompo e ka sebetsa ho tloha ho 450 RPM ho ea ho 3450 RPM ka lebelo le 750 la preset ea 1500, 2350, 3110 le XNUMX RPM, kapa pompo e ka behoa ho laola lebelo la eona le ho boloka lebelo la ho phalla kamehla.
• Pompo e ka ikamahanya le lits'ebetso lipakeng tsa 20 le 140 GPM. Etsa feela lenaneo la pompo ho tekanyo ea phallo e lakatsehang, 'me pompo e tla ikamahanya le maemo a ts'ebetso ho boloka tekanyo eo ea phallo e itseng.
• Ho fihla ho li-program tse 8 tseo u ka li khethang tse ka hlophisoang hore li tsamaee kapa li potlake ka linako tsohle ka mekhoa ea Manual, Egg Timer kapa Schedule.
• Alamo ea phanele ea pompo ea LED le melaetsa ea liphoso e lemosa mosebelisi ka ts'ebetso e sa lokelang.
• Mokhoa oa priming o hlophisitsoeng o nang le ts'ebetso ea othomathike ea mantlha bakeng sa ho qala habonolo le ho lemoha tahlehelo ea boleng bo holimo.
• E lumellana le lisebelisoa tse ngata tsa ho hloekisa, li-filters le li-spas tsa liketso tsa jet.
• WEF 6.9 THP 3.95

Sethala sa Kopano ea Tsamaiso le Taolo
IntelliFlo VSF pump drive e etselitsoe ho hlahisa katleho e kholo ea ts'ebetso ea makoloi. Koloi e laola lebelo la ho potoloha ha enjene ka ho laola maqhubu a motlakase o fanoeng. E boetse e sireletsa enjene le pompo hore li se sebetse ka ntle ho litekanyo tsa bona tsa ts'ebetso tse reriloeng.
Panopo ea taolo e ka ts'oaroa pompong ka litsela tse fapaneng tse fapaneng ho fa mosebelisi phihlello e ntle. Panopo ea taolo le eona e ka ts'oaroa sebakeng se loketseng haholoanyane ka thuso ea kit ea phalliso ea keypad (P / N 356904Z).
Taolo ea Kantle
Lits'ebetso tse ngata tsa bo-Pentair le Litsi tsa Puisano tsa IntelliComm® li ka laola pompo ea IntelliFlo VSF ka remoutu. Aterese ea puisano ea pompo le mesebetsi e meng e fumaneha ho tsoa phanele ea taolo ea pompo.

• Mohala oa puisano oa RS-485 o kenyelelitsoe
• Sistimi ea IntelliComm e laola pompo e le 'ngoe ea IntelliFlo e sebelisa mananeo a 4 a Taolo ea Kantle.

Sheba buka ea automation system bakeng sa lintlha tse ling mabapi le mokhoa oa ho hokela le ho sebelisa sistimi ka pompo ea hau e feto-fetohang ea lebelo.
Lisebelisoa tsa Likoloi

• Matla a Phahameng a Permanent Magnet Synchronous Motor (PMSM)
• Taolo e phahameng ea lebelo
• E sebetsa ka mocheso o tlase ka lebaka la ts'ebetso e phahameng
• E etselitsoe ho mamella tikoloho ea kantle
• Fan e Koetsoeng ka ho Fetisisa e Folisitsoeng (TEFC) Motor
• 56 Square Flange
• Lerata le tlase
  Likarolo tsa Drive
• Tokiso e Matla ea Matla a Matla
• Keypad e fetolehang
• Wiring e Bonolo ea Overhead
• Phaello e Phahameng ea Ts'ebetso ea Ts'ebetso
• Theknoloji ea Phallo e se Nang le Khatello ea Khatello
• Tahlehelo ea Tonakholo

KEKETSO

Ke setsebi sa lipeipi feela se tšoanelehang se lokelang ho kenya IntelliFlo® VSF Variable Speed ​​le Flow Pump. Sheba "Tlhokomeliso ea Bohlokoa ea Pompo le Litaelo tsa Tšireletseho" leqepheng la i - ii bakeng sa boitsebiso bo eketsehileng ba ho kenya le polokeho.
Hlokomela: Pompo ea IntelliFlo VSF ha e khone ho hokeloa ka letoto le lipompo tse ling.
Sebaka
Hlokomela: Se ke oa kenya pompo ena ka har'a sebaka se ka ntle kapa ka tlas'a moleka oa bate e chesang kapa spa ntle le haeba u tšoailoe ka nepo.
Hlokomela: Netefatsa hore pompo e sirelelitsoe ka mochini sebakeng sa lisebelisoa.
Etsa bonnete ba hore sebaka sa pompo se fihlela litlhoko tse latelang:

1. Kenya pompo haufi le letamo kapa spa ka hohle kamoo ho ka khonehang.
   Ho fokotsa tahlehelo ea likhohlano le ho ntlafatsa ts'ebetso e sebetsang, sebelisa lipompo tse khuts'oane tse hohelang ka kotloloho.
2. Kenya bonyane maoto a 5 (1.5 metres) ho tloha leboteng le ka hare la letamo le spa. Mehaho ea Canada e hloka bonyane ba maoto a 9.8 (limithara tse 3) ho tloha boemong ba metsi a letamo.
3. Kenya pompo bonyane maoto a 3 (limithara tse 0.9) ho tloha setsing sa futhumatsang.
4. Se ke oa kenya pompo ho feta maoto a 10 (limithara tse 3.1) ka holim'a boemo ba metsi.
5. Kenya pompo sebakeng se nang le moea o motle o sirelelitsoeng ho mongobo o feteletseng (ke hore, liphaephe tsa metsi a pula, lisebelisoa tsa ho fafatsa, joalo-joalo).
6. Kenya pompo e nang le sebaka se ka morao sa bonyane 3-inch (76.2 mm) e le hore motlakase o ka ntšoa habonolo bakeng sa tlhokomelo le ho lokisoa. Sheba Setšoantšo sa 1.

Papali

1. Bakeng sa liphaephe tse ntlafalitsoeng tsa letamo, ho khothalletsoa ho sebelisa boholo bo boholo ba phala. Ha u kenya lisebelisoa tsa ho kenya le ho tsoa (li-adapter tsa banna), sebelisa sealant ea khoele.
2. Liphaephe tse lehlakoreng la ho hula la pompo li lokela ho tšoana kapa tse kholo ho feta bophara ba mohala oa ho khutla.
3. Ho kenya liphaephe ka lehlakoreng la ho huloa ha pompo ho lokela ho ba nako e khutšoanyane ka hohle kamoo ho ka khonehang.
4. Bakeng sa lits'ebetso tse ngata, Pentair e khothaletsa ho kenya valve ho pompo ea ho hula le ho khutla e le hore pompo e ka aroloa nakong ea tlhokomelo e tloaelehileng.
   Re boetse re khothaletsa valve, setsoe kapa tee e kentsoeng moleng oa ho hula ha ea lokela ho ba haufi le karolo e ka pele ea pompo ho feta makhetlo a mahlano (5) ho feta bophara ba peipi ea ho hula. Sheba Setšoantšo sa 2.
   Example: Phaephe ea 2-inch e hloka lebelo le otlolohileng la lisenthimithara tse 10 (254 mm) ka pel'a sebaka se kenang sa pompo).
   Sena se tla thusa pompo ho qala kapele le ho tšoarella nako e telele.
   Hlokomela: U SE KE UA kenya litsoe tsa 90° ka kotloloho ka har'a seketsoana sa pompo.

Litlhoko tsa Motlakase

• Kenya lisebelisoa tsohle ho latela Khoutu ea Naha ea Motlakase le likhoutu le melaoana eohle e sebetsang ea lehae.
• Mokhoa oa ho khaoha o tlameha ho kenngoa ka har'a mohala o tsitsitseng ho latela melao ea mohala.

Kit ea Boiketsetso ea Keypad
Maemong a ikhethileng ha mosebelisi a haelloa ke phihlello e bonolo kapa e bonolo ea pompo ea IntelliFlo VSF, Keypad Relocation Kit (P/N 356904Z) e ka rekoa ho morekisi oa lehae oa hau oa lisebelisoa tsa letamo. Setsi sena se lumella mosebelisi ho tlosa letlapa la likonopo kaholimo ho drive ebe o kenya konopo sebakeng se tsitsitseng se nang le phihlello e ntle.
Bakeng sa litaelo tsa ho instola, sheba Litaelo tsa ho Kenyetsoa ha Keypad Relocation Kit tse fanoeng le khiti.
Lisebelisoa le li-valve

1. Se ke oa kenya litsoe tsa 90° ka kotloloho ka har'a seketsoana sa pompo.
2. Litsamaiso tsa ho hula ka likhohola li lokela ho ba le li-valve tse kentsoeng liphaepheng tse monyang le tse ntšang metsi bakeng sa tlhokomelo, leha ho le joalo, valve ea ho hula ha ea lokela ho ba haufi le makhetlo a mahlano bophara ba peipi ea ho hula joalokaha ho hlalositsoe karolong ena.
3. Sebelisa valve ea ho hlahloba moleng oa ho tsoa ha u sebelisa pompo ena bakeng sa kopo leha e le efe moo ho nang le bophahamo ba bohlokoa ho liphaephe ka mor'a pompo.
4. Etsa bonnete ba hore u kenya li-valve tsa ho hlahloba ha lipeipi li tsamaisana le pompo e 'ngoe. Sena se thusa ho thibela ho potoloha ha impeller le motor.

Kemiso ea Motlakase
KOTSI EA TSIETSO EA MOTSOALLE KAPA ELECTROCUTION. Pompo ena e tlameha ho hlongoa ke ramohlo ea laesense kapa ea netefalitsoeng kapa setsebi sa litšebeletso se tšoanelehang ho latela Khoutu ea Motlakase ea Naha le likhoutu le melao eohle e sebetsang ea lehae.
Ho kenya ka mokhoa o sa nepahalang ho tla baka kotsi ea motlakase e ka bakang lefu kapa kotsi e mpe ho basebelisi, ba kenyang lintho, kapa ba bang ka lebaka la ho tsukutloa ke motlakase, hape e ka baka tšenyo ea thepa.
Kamehla hakolla motlakase ho pompo ho sekhechana sa potoloho pele u sebeletsa pompo. Ho hloleha ho etsa joalo ho ka fella ka lefu kapa kotsi e mpe ho batho ba sebeletsang, basebelisi kapa ba bang ka lebaka la ts'ebetso ea motlakase.
Bala litaelo tsohle tsa ts'ebeletso pele u sebetsa pompong.
Hlokomela: NAKO TSOHLE kenya sekoaelo sa koloi sebakeng sa khoele ha u siea pompo e sa behoa leihlo nakong ea ts'ebetso. Sena se tla thibela lintho tse tsoang kantle ho naha (ke hore, metsi a pula, lerōle, joalo-joalo) ho bokellana ka koloing.
Hlokomela: Ha o kopanya pompo ho tsamaiso ea othomathike, matla a tsoelang pele a tlameha ho fanoa pompong ka ho e hokahanya ka ho toba ho sekheo sa potoloho. Ha o sebelisa sistimi ea othomathike, etsa bonnete ba hore ha ho na mabone a mang kapa lisebelisoa tse teng potolohong e le 'ngoe.
Wiring

1. Etsa bonnete ba hore li-breaker tsohle tsa motlakase le li-switches lia tingoa pele u kenya motlakase.
   TŠEBELETSO EA TŠEBELETSO - Ema bonyane metsotsoana e mashome a tšeletseng (60) pele u sebeletsa.
2. Etsa bonnete ba hore phepelo voltage kopana le litlhokahalo tse thathamisitsoeng ho nameplate ea enjene. Haeba litlhoko tsena li sa finyelloe, tšenyo e sa feleng e ka 'na ea etsahala.
3. Bakeng sa boholo ba lithapo le litataiso tse akaretsang bakeng sa ho kenya motlakase hantle, ka kopo latela lintlha tse hlalositsoeng ho Khoutu ea Naha ea Motlakase le likhoutu life kapa life tsa lehae kamoo ho hlokahalang.
4. Sebelisa ho imolla khatello 'me u netefatse hore likhokahano tsohle tsa motlakase li hloekile ebile li tiile.
5. Seha lithapo ka bolelele bo loketseng hore li se ke tsa kopana kapa tsa ama ha li hokahantsoe.
6. Kenya konopo hape ka mor'a ho thaepa pompo ka ho hokela sekoaelo morao ho khokahanyo ea lithapo tsa koloi le ho lula hape letlapa la likonopo ka lehlakoreng le lakatsehang ka likurufu tse 'ne (4) tse hukung.
   Hlokomela: Netefatsa hore thapo ya letlapa la dikonopo ha e a totobala pakeng tsa koloi le letlapa la dikonopo nakong ya ho dula hape.

Ho thethefatsa

1. Theola koloi ka ho sa feleng u sebelisa screw ground e tala, joalokaha ho bontšitsoe ka tlase. Sebelisa boholo bo nepahetseng ba terata le mofuta o boletsoeng ke Khoutu ea Naha ea Motlakase. Etsa bonnete ba hore terata ea fatše e hoketsoe sebakeng sa litšebeletso tsa motlakase.
2. Pompo e lokela ho hokelloa ka ho sa feleng ho sekhechana sa potoloho, sebali sa nako ea 2-pole kapa 2-pole relay.
   Tlhokomeliso: Haeba motlakase oa AC o fanoa ke sekhechana sa potoloho sa GFCI, pompo e lokela ho hokeloa ka thapo e ikemetseng ntle le haeba pompo e sebelisoa hammoho le jenereithara ea chlorine ea letsoai ea Pentair.

Tlamahano

1. Tlama enjene ho sebopeho ho latela Khoutu ea Naha ea Motlakase. Sebelisa sekontiri se tiileng sa koporo se seng nyane ho feta 8 AWG. Bakeng sa lisebelisoa tsa Canada, 6 AWG kapa sekontiri se seholoanyane se tiileng sa koporo sea hlokahala. Tsamaisa terata ho tloha ho sekoti sa bonding sa kantle ho ea ho sebopeho sa bonding.
2. Hokela terata ho tloha mokotleng o fihlellehang oa enjene ho ea likarolong tsohle tsa tšepe tsa letamo la ho sesa, spa, kapa libate tse chesang le lisebelisoa tsohle tsa motlakase, conduit ea tšepe le lipeipi tsa tšepe ka har'a maoto a 5 (1.52 metres) ho tloha maboteng a ka hare. letamo la ho sesa, spa, kapa bate e chesang. Tsamaisa terata ho tloha ho sekoti sa bonding sa kantle ho ea ho sebopeho sa bonding.

Hlokomela: Ha pompo e qalisoa 'me e emisoa ka ho tlosa matla ka relay kapa timer, sesebelisoa sa lipalo tse peli se lokela ho sebelisoa ho kenya le ho tlosa matla ho POWER LINE TERMINALS ka bobeli.
Pentair e fana ka 2-Pole 20 Amp Li-breaker tsa GFCI (P/N PA220GF) tse fanang ka tšireletso ea basebetsi ha li ntse li kopana 2008 ho ea ho Melao ea hajoale ea NEC bakeng sa Lipompo tsa Letamo.
Ho hokela ho Sisteme e Iketsetsang
Lipompompo tsohle tsa IntelliFlo le IntelliPro, ho kenyelletsa le IntelliFlo® VSF Variable Speed ​​le Flow Pump, li tsamaisana le Pentair Automation Systems.
Mohala oa puisano oa RS-485 o fanoa ka pompo 'me o tla sebelisoa ho hokahanya pompo ho sistimi ea othomathike ea Penair.
Sheba buka ea automation system bakeng sa lintlha tse ling mabapi le mokhoa oa ho hokela le ho sebelisa sistimi ka pompo ea hau e feto-fetohang ea lebelo.
IntelliTouch® Control System e nang le firmware 1.170 kapa pejana e tla hlahisa "VSF+SVRS" mofuteng oa pompo/khethong. Ha o ntse o tla khetha khetho ena, pompo ea IntelliFlo VSF HA E kenyeletse tšireletso ea SVRS.

TŠEBELETSO POMPI

HLOKOMELA: Ha o theha IntelliFlo® VSF Variable Speed ​​and Flow Pump, mosebelisi o tlameha ho seta oache e kahare ea pompo mme a thehe kemiso ea ts'ebetso ka ho latela mehato e bukeng ena. Ka kopo sheba likarolo tsa tataiso ea basebelisi: 'Beha Nako' (leqephe la 10) le 'Beha Mananeo 1-8 ka Mokhoa oa Kemiso' (leqephe la 15) ho hlophisa nako ea ho tsamaisa pompo.
Pompo ena e romelloa ka mokhoa oa Priming ENABLED. Ntle le haeba litlhophiso tsa Priming li fetoloa ho menu, hlokomela hore pompo e tla potlakisa lebelo le leholo ha pompo e tsamaisoa ka lekhetlo la pele, 'me konopo ea Qala / Stop e hatelloa. Ho fetola lebelo le phahameng la pompo, sheba leqephe la 10.
Pele o BULA pompo, etsa bonnete ba hore maemo a latelang a a fihlelleha:

1. Belofo e bulehileng ea ho thusa moea.
2. Li-valve tse bulehileng.
3. Letamo la ho khutlisa le bulehile ka botlalo 'me ha ho na litšitiso leha e le life.
4. Metsi ka basketeng ea pompo.
5. Ema hole le sefe kapa lijana tse ling tse hatelitsoeng.

Ho phahamisa Pompo
Qala pompo pele u qala pompo ka lekhetlo la pele. Tlosa sekwahelo 'me u tlatse baskete ka metsi. Seroto sa pompo se tlameha ho tlatsoa ka metsi pele se qala kapa ka mor'a ho sebeletsa.
Latela mehato e ka tlase ho qala pompo bakeng sa ho qala:

1. Tobetsa Qala/Emisa ho emisa pompo. Hakolla thapo e kholo ea phepelo ea motlakase le thapo ea puisano.
2. Koala li-valve tsohle ka liphaephe tse monyang le tse ntšang metsi.
   Fokotsa khatello eohle ea sistimi.
3. Tlosa sekwahelo sa pompo le reng ea ho notlela.
4. Tlatsa pitsa ea pompo ka metsi.
5. Kopanya sekoaelo sa pompo hape le reng ea ho notlela holim'a basketeng ea sefa. Pompo e se e loketse ho qala.
6. Bula li-valve tsohle ka liphaephe tse monyang le tse ntšang metsi.
7. Bula valve ea ho thusa moea oa sefa 'me u eme ka ntle ho sefe.
8. Hokela matla ho pompo. Etsa bonnete ba hore lebone la motlakase o motala le khantšitsoe.
9. Tobetsa Qala/Emisa ho qala pompo. Pompo e tla kena ka mokhoa oa priming (haeba e nolofalitsoe) 'me e potlakele ho lebelo le phahameng le behiloeng ho litlhophiso tsa menu ea pompo.
10. Ha metsi a tsoa ka valve ea sefa moea, koala valve. Hona joale tsamaiso e lokela ho se na moea le ho khutlisetsa metsi ho ea le ho tsoa letamong
11. Se ke oa lumella pompo ea hau ho sebetsa nako e telele ho feta metsotso e 30 ntle le ho hlahisa phallo e felletseng. Haeba pompo e sa qale, sheba litlhophiso tsa hau tsa ho qala ho phanele ea taolo kapa sheba karolo ea "Troubleshooting" leqepheng la 25-27.

Litaba tsa Priming
Peakanyo ea mantlha ea priming e SEBETSOE.
Pompo e boetse e u lumella ho beha tse latelang ho tsoa ho phanele ea taolo ea opareitara:

• Lebelo la ho qala
• Boemo ba pele (1-10)
• Ho lieha ho qala

Etsa litaelo leqepheng la 19.
U se ke ua kenya lik'hemik'hale tsamaisong ka ho toba ka pel'a ho hula pompo. Ho eketsa lik'hemik'hale tse sa hloekisoang ho ka senya pompo 'me ho tla hlakola waranti.
Ena ke pompo ea lebelo e feto-fetohang. Ka tloaelo lebelo le tlase le sebelisetsoa ho sefa le ho futhumatsa. Lebelo le phahameng le ka sebelisoa bakeng sa li-jets tsa spa, likarolo tsa metsi, le li-priming.
U SE KE UA omisa pompo. Haeba pompo e omme, tiiso ea mochini e tla senyeha 'me pompo e qala ho lutla.
Haeba sena se etsahala, tiiso e senyehileng e tlameha ho nkeloa sebaka. KA TSOHLE boloka boemo bo nepahetseng ba metsi ka letamong la hau (halofo ea ho nyoloha butle butle). Haeba boemo ba metsi bo oela ka tlas'a ho buloa ha skimmer, pompo e tla hula moea ka skimmer, e lahleheloa ke prime le ho etsa hore pompo e ome, e leng se etsang hore ho be le tiiso e senyehileng. Ts'ebetso e tsoelang pele ka mokhoa ona e ka baka tahlehelo ea khatello, e bakang tšenyo ea mokotla oa pompo, impeller le seal mme e ka baka thepa le kotsi ea motho.
Ho sebelisa Panel Control Panel
Sebelisa phanele ea taolo ea opareitara ho qala le ho emisa IntelliFlo® VSF Variable Speed ​​le Flow Pump, seta, le ho fetola mananeo, le ho fihlella likarolo le li-setting tsa pompo.
Litaolo le li-LED ho Keypad

1. Konopo ea 1: Tobetsa ho khetha Lenaneo 1 (750 RPM). LED on e bonts'a Lenaneo la 1 le sebetsa.
2. Konopo ea 2: Tobetsa ho khetha Lenaneo 2 (1500 RPM). LED on e bonts'a Lenaneo la 2 le sebetsa.
3. Konopo ea 3: Tobetsa ho khetha Lenaneo 3 (2350 RPM). LED on e bonts'a Lenaneo la 3 le sebetsa.
4. Konopo ea 4: Tobetsa ho khetha Lenaneo 4 (3110 RPM). LED on e bonts'a Lenaneo la 4 le sebetsa.
5. Morao: E khutlela mohato o le mong ho menu; e tsoa ntle le ho boloka litlhophiso tsa hajoale.
6. Boloka: E boloka tlhophiso ea ntho ea hajoale ea menu. Ha parameter e fetotsoe, "Save?" letšoao le tla hlahisoa.
7. Menu: E fihlella linthong tsa menyu ha pompo e emisoa.
8. Khetha: Tobetsa ho khetha khetho e hlahang skrineng.
9. Likonopo tsa motsu:
   • Motsu o hodimo: Tsamaisa mohato o le mong ho menu kapa eketsa didijiti ha o lokisa maemo.
   • Motsu o tlase: Suthela boemo bo le bong tlase ho menu kapa fokotsa palo ha o lokisa maemo.
   • Motsu o ka ho le letshehadi: Tsamaisa ka sesupa sa nomoro e le 'ngoe ha u hlophisa maemo
   • Motsu o ka ho le letona: Tsamaisa sekhutlo ka ho le letona ha o fetisa boemo.
10. Ho Hloekisa ka Potlako: Pompo e nyolohela ho RPM e phahameng (bakeng sa ho hloekisa, ho hloekisa, ho eketsa lik'hemik'hale, joalo-joalo). Lebone la LED le bulehile ha le sebetsa.
11. Nako ea ho tsoa: Lumella pompo hore e lule e eme ka nako e behiloeng pele e qala ts'ebetso e tloaelehileng.
    LED e butswe ha e sebetsa.
12. Qala / Emisa konopo: Ho qala kapa ho emisa pompo. Ha LED e butse, pompo ea sebetsa kapa e boemong ba ho qala ka bo eona.
13. Seta konopo hape: Seta alamo bocha kapa tlhokomeliso.
14. Li-LED:
    Bula: Lebone le letala ha pompo e buletsoe.
    Tlhokomeliso: Bula haeba boemo ba temoso bo le teng. Sheba “Litemoso le Litemoso” leqepheng la 25.
    Alamo: LED e khubelu e bulehile haeba boemo ba alamo bo hlaha. Sheba “Litemoso le Litemoso” leqepheng la 25.
15. Sesebelisoa sa LCD sa Control Panel:
    • Mola oa 1: Letšoao la senotlolo le bontša mokhoa oa ho sireletsa phasewete oa sebetsa. Haeba ts'ireletso ea password e sa lumelloa, ha ho letšoao la senotlolo le hlahang. E boetse e bontša nako ea hona joale ea letsatsi. Li-cursor tse sebetsang li hlaha ha senotlolo sa motsu se fumaneha.
    • Mola oa 2: E bonts'a lebelo / phallo ea pompo ea hajoale (RPM / GPM).
    • Mola oa 3: Nako ea ho bala le li-watts
    • Mola oa 4: Boemo ba pompo ea hajoale le tšobotsi ea hajoale.
    “Boloka?” e tla hlaha moleng ona ha phetoho ea parameter e ka bolokoa.

Hlokomela: Kamehla koala sekwahelo sa letlapa la dikonopo ka mora ho sebedisa letlapa la dikonopo.
Hlokomela: Ho sebelisa li-screwdrivers kapa lipene ho hlophisa pompo ho tla senya sekoaelo sa likonopo. Sebelisa menoana ea hau feela ha u hlophisa pompo.
Ho emisa le ho qala pompo
Ho qala Pompo

1. Etsa bonnete ba hore pompo e buletsoe 'me matla a tala a LED a butsoitse.
2. Khetha e 'ngoe ea likonopo tsa lenaneo, ebe o tobetsa konopo ea Start/Stop (LED on) ho qala pompo. Pompo e tla kena mokhoeng oa priming haeba karolo ea priming e nolofalitsoe.

Ho emisa Pompo

1. Tobetsa Qala/Emisa ho emisa pompo.
   Ha u sebeletsa lisebelisoa (li-filters, heaters, chlorinators joalo-joalo), khaola thapo ea puisano, 'me u TŠOME sekhechana sa potoloho ho tlosa matla pompong.
   Hlokomela: Pompo e ka qala hape ka bo eona haeba thapo ea puisano e hokahane.

Ho fetola le ho boloka lebelo / phallo ea pompo

1. Ha pompo e ntse e sebetsa, tobetsa motsu oa Holimo kapa Tlase ho ikamahanya le lebelo leo u le batlang kapa boemo ba phallo.
2. Tobetsa o hatelle konopo ea Lenaneo (1-4) metsotsoana e meraro (3) ho boloka lebelo/phallo ho konopo kapa tobetsa Save ho boloka lebelo/phallo.

Ho sebelisa Pump ho Preset Speed
Pompo e hlophisitsoe ka lebelo la kamehla la 750, 1500, 2350 le 3110 RPM. Likonopo tsa 1-4 ke tsa lebelo le leng le le leng le behiloeng esale pele joalo ka ha ho bonts'itsoe ka tlase.

1. Etsa bonnete ba hore pompo e buletsoe 'me matla a tala a LED a butsoitse.
2. Tobetsa konopo ea Program (1- 4) e tsamaellanang le lebelo le reriloeng esale pele 'me u lokolle kapele.
   LED e kaholimo ho konopo e tla bulela.
3. Tobetsa Qala/Emisa. Pompo e tla fetoha kapele ho lebelo le khethiloeng esale pele.

Mekhoa e sebetsang ea Pump
IntelliFlo® VSF Variable Speed ​​le Flow Pump e ka hlophisoa ka mekhoa e meraro e fapaneng:
Mananeo 1-4 a ka hlophisoa ka mekhoa eohle e meraro.
Mananeo 5-8 a ka hlophisoa feela ka mokhoa oa Kemiso kaha ha ho na likonopo sebakeng sa taolo bakeng sa Mananeo 5-8. Litlhophiso tsa kamehla bakeng sa Mananeo 5-8 ke "Ho holofetse".Bukana
E abela lebelo kapa phallo ho e 'ngoe ea likonopo tse 'ne tsa Lenaneo ho phanele ea taolo. Mokhoa ona o ka sebelisoa feela bakeng sa mananeo a 1-4. Mananeo 1 le 2 ke Manual ka ho sa feleng.
Ho sebetsa ka mokhoa oa Manual, tobetsa e 'ngoe ea likonopo tse' nè tsa lenaneo ebe o tobetsa konopo ea Qala/Emisa. Pompo e tla tsamaisa lebelo le fanoeng kapa phallo e abetsoeng konopo ea lenaneo.
Nako ea Lehe
Mananeo 1-4 a ka hlophisoa hore a tsamaee ka lebelo le itseng kapa phallo le ka nako e telele hang ha konopo ea lenaneo e tobetse.
Mananeo 3 le 4 ke Li-Egg Timers ka ho iketsa. Haeba u lakatsa mokhoa o fapaneng oa ts'ebetso, mananeo a 3 le 4 a ka fetoloa ho "Manual mode" ho menu ea taolo.
Ho sebetsa ka mokhoa oa Egg Timer, tobetsa konopo ea lenaneo ebe o tobetsa Qala/Emisa. Pompo e tla tsamaisa sebaka seo bakeng sa nako e behiloeng ebe e tima.
Kemiso
Mananeo 1-8 a qala mme a emisa ka nako e itseng nakong ea lihora tse 24. Lebelo kapa phallo e hlophisitsoeng ka mokhoa oa Shejule e tla fetisa lebelo kapa phallo efe kapa efe e khethiloeng ka letsoho hang ha taelo e latelang ea Kemiso e qala.
Mefuta ea Lenaneo
Pompo ena e ka tsamaisa mananeo a bolokiloeng ka lebelo le sa feleng kapa lebelo la phallo e sa feleng. Sena se fa mosebelisi bokhoni ba ho abela sehlahisoa se tsoang pompong hantle hore ho se ke ha senyeha matla le hore mosebetsi o phetheloe ka nepo.
Hlokomela: Sekhahla sa phallo e bonts'itsoeng ha se so hlahlojoe ho latela litlhoko tsa mitha ea phallo ea NSF/ANSI/CAN 50.
Panel ea Taolo ea Ts'ebetso: Tataiso ea Li-pump MenuPanel ea Taolo ea Opereishene: Tataiso ea Menu ea Pompo (tsoela pele)
Beha Letsatsi le Nako
Nako e laola linako tsohle tse hlophisitsoeng, mesebetsi, le lipotoloho tse hlophisitsoeng 'me e boloka nako e nepahetseng ho fihlela lihora tse 96 ka mor'a hore motlakase o tingoe. Seta hape haeba motlakase o timme nako e telele ho feta lihora tse 96.

1. Sheba hore na LED e nang le matla a matala e butse.
2. Tobetsa Menu.
3. Tobetsa Khetha ho khetha "Settings".
4. Sebelisa metsu ea Holimo kapa Tlase ho tsamaisetsa ho "Letsatsi le Nako". Tobetsa Khetha.
5. Tobetsa Khetha hape 'me u sebelise metsu ea Holimo kapa Tlase ho seta letsatsi.
6. Tobetsa Save ho boloka mosebedisi le ho khutlela ho "Letsatsi le Nako."
7. Sebelisa metsu ea Holimo kapa Tlase ho tsamaisetsa ho "Nako". Tobetsa Khetha.
8. Sebelisa metsu ea Holimo kapa Tlase ho tsamaisetsa ho hlophisa nako.
   Hlokomela: Ho seta AM/PM kapa oache ea lihora tse 24 sheba karolo e latelang ea "Beha AM/PM kapa 24 Hour Clock."
9. Tobetsa Boloka ho boloka. Ho hlakola liphetoho life kapa life, tobetsa Khutlela ho tsoa ntle le ho boloka.
10. Tobetsa Morao ho tsoa.

Beha oache ea AM/PM kapa ea lihora tse 24
Ho fetola nako ho tloha ho oache ea lihora tse 12 (AM/PM) ho ea ho ea lihora tse 24:

1. Tobetsa Menu.
2. Tobetsa Khetha ho khetha "Settings".
3. Sebelisa metsu ea Holimo kapa Tlase ho tsamaisetsa ho "Letsatsi le Nako". Tobetsa Khetha.
4. Sebelisa metsu ea Holimo kapa Tlase ho tsamaisetsa ho "AM/PM".
   Tlanya Khetha.
5. Sebelisa metsu ea Holimo kapa Tlase ho tsamaisetsa ho khetha pakeng tsa lihora tse 24. le AM/PM.
6. Tobetsa Boloka ho boloka. Ho hlakola liphetoho leha e le life, tobetsa Khutlela ho tsoa ntle le ho boloka.
7. Tobetsa Morao ho tsoa.

Beha Bonyane ba Lebelo (RPM)
Lebelo le tlase la pompo le ka setoa ho tloha ho 450 RPM ho isa ho 1700 RPM. Boemo ba kamehla ke 450 RPM.

1. Sheba hore na LED e nang le matla a matala e butse.
2. Tobetsa Menu.
3. Tobetsa Khetha ho khetha "Settings".
4. Sebelisa metsu ea Holimo kapa Tlase ho tsamaisetsa ho "Min/Max".
   Tlanya Khetha.
5. Sebelisa metsu ea Holimo kapa Tlase ho tsamaisetsa ho "Set Min Spd".
6. Tobetsa Kgetha ho fetola tlhophiso. Sekhesa se tla hlaha kholomong ea linomoro tsa pele (tse ling).
7. Tobetsa metsu ea Holimo kapa Tlase ho hlophisa lebelo le tlase ho tloha ho 450 ho isa ho 1700 RPM.
8. Tobetsa Boloka ho boloka. Ho hlakola, tobetsa Khutlela ho tsoa molemong oa ho fetola ntle le ho boloka.
9. Tobetsa Morao ho tsoa.

Beha Lebelo le Leholo (RPM)
Lebelo le phahameng le ka beoa ho tloha ho 1900 RPM ho isa ho 3450 RPM (kamehla ke 3450). Sebelisa mokhoa ona ho seta lebelo le phahameng la ho sebetsa la IntelliFlo® VSF Variable
Lebelo le Phallo Pompe.
Hlokomela: Li-setting tsa boholo le lebelo la bonyane, le lialamo tse amanang le tsona, li lula li le teng ha li le Flow mode.

1. Sheba hore na LED e nang le matla a matala e butse.
2. Tobetsa Menu.
3. Tobetsa Khetha ho khetha "Settings".
4. Sebelisa metsu ea Holimo kapa Tlase ho tsamaisetsa ho "Min/Max".
   Tlanya Khetha.
5. Sebelisa metsu ea Holimo kapa Tlase ho tsamaisetsa ho "Set Max Spd".
6. Tobetsa Kgetha ho fetola. Sekhesa se tla hlaha kholomong ea linomoro tsa pele (tse ling).
7. Tobetsa metsu ea Holimo kapa Tlase ho hlophisa lebelo le phahameng ho tloha ho 1900 ho isa ho 3450 RPM.
8. Tobetsa Boloka ho boloka. Tobetsa Morao ho tsoa. Ho hlakola, tobetsa Khutlela ho tsoa ntle le ho boloka.

Tlhokomeliso: Lebelo le Leholo le tla fokotsa Lebelo la Priming, ntle le ketsahalong e le 'ngoe. Haeba Lebelo le Phahameng le behiloe ka tlase ho lebelo le tlaase ka ho fetisisa la Priming Speed ​​(2400 RPM) joale pompo e tla feta Maximum Speed ​​ha karolo ea priming e ntse e sebetsa. Sena se thibela ump ho ba le bothata ba ho qala haeba Maximum Speed ​​​​e behiloe tlase tjena. Haeba sena e le bothata, ho qapa ho ka koaloa ho Priming Menu (sheba karolo ea "Priming" leqepheng la 17).
Beha Boemo bo Bonyane ba Phallo (GPM)
Sekhahla se tlase sa phallo e hlophisitsoeng se ka beoa ho tloha ho 20 GPM ho isa ho 70 GPM.

1. Sheba hore na LED e nang le matla a matala e butse.
2. Tobetsa Menu.
3. Tobetsa Khetha ho khetha "Settings".
4. Sebelisa metsu ea Holimo kapa Tlase ho tsamaisetsa ho "Min/Max" ebe o tobetsa Khetha.
5. Sebelisa metsu ea Holimo kapa Tlase ho tsamaisetsa ho "Seta Bonyane ba Phallo".
6. Tobetsa Kgetha ho fetola tlhophiso. Sekhesa se tla hlaha kholomong ea linomoro tsa pele (tse ling).
7. Tobetsa metsu ea Holimo kapa Tlase ho hlophisa boemo bo tlase ba sekhahla sa phallo ho tloha ho 20 ho isa ho 70 GPM.
8. Tobetsa Boloka ho boloka. Ho hlakola, tobetsa Khutlela ho tsoa molemong oa ho fetola ntle le ho boloka.
9. Tobetsa Morao ho tsoa.

Beha Sekhahla se Phahameng sa Phallo (GPM)
Sekhahla se phahameng sa phallo e hlophisitsoeng se ka beoa ho tloha ho 80 GPM ho isa ho 140 GPM.
Hlokomela: Li-setting tsa boholo le lebelo la bonyane, le lialamo tse amanang le tsona, li lula li le teng ha li le Flow mode.

1. Sheba hore na LED e nang le matla a matala e butse.
2. Tobetsa Menu.
3. Tobetsa Khetha ho khetha "Settings".
4. Sebelisa metsu ea Holimo kapa Tlase ho tsamaisetsa ho "Min/Max".
   Tlanya Khetha.
5. Sebelisa metsu ea Holimo kapa Tlase ho tsamaisetsa ho "Set
   Phallo e Phahameng”.
6. Tobetsa Kgetha ho fetola tlhophiso. Sekhesa se tla hlaha kholomong ea linomoro tsa pele (tse ling).
7. Tobetsa metsu ea Holimo kapa Tlase ho hlophisa maemo a phahameng a phallo ho tloha ho 80 ho isa ho 140 GPM.
8. Tobetsa Boloka ho boloka. Ho hlakola, tobetsa Khutlela ho tsoa molemong oa ho fetola ntle le ho boloka.
9. Tobetsa Morao ho tsoa.

Beha Moeli oa Phallo bakeng sa Lenaneo la Lebelo
Moeli oa ho phalla ho mofuta oa lenaneo la lebelo le sa khaotseng o koaletsoe ka ho sa feleng. Tlhophiso ena e lumella mosebedisi ho etsa bonnete ba hore koloi ha e fetise sekhahla sa phallo e behiloeng ha ba sebetsa ka mokhoa o tsitsitseng oa lebelo. Tsamaiso e ka 'na ea fetoha nakong ea ho matha ka lebelo le sa khaotseng le neng le tla eketsa lebelo la phallo, e leng tšobotsi ena e nolofalitsoe joale pompo e tla ikemela ka boeona ho boloka ka tlaase ho tekanyo e phahameng ea Phallo e behiloeng pele.

1. Sheba hore na LED e nang le matla a matala e butse.
2. Tobetsa Menu.
3. Tobetsa Khetha ho khetha "Settings".
4. Sebelisa metsu ea Holimo kapa Tlase ho tsamaisetsa ho "Min/Max" ebe o tobetsa Khetha.
5. Sebelisa metsu ea Holimo kapa Tlase ho tsamaisetsa ho "Flow Limit (Lebelo)".
6. Tobetsa Khetha ho tsamaisa cursor holim'a "Holofetse".
7. Tobetsa le metsu ea Holimo kapa Tlase ho e fetolela ho "Enabled".
8. Tobetsa Boloka ho boloka. Ho hlakola, tobetsa Khutlela ho tsoa molemong oa ho fetola ntle le ho boloka.
9. Tobetsa Morao ho tsoa.

Beha Khatello e Phahameng ea Tsamaiso
Khatello e phahameng ka ho fetisisa e ka behoa ho sebelisa koloi, e le hore pompo e se ke ea feta tekanyo ea khatello ea tsamaiso e behiloeng ha e botsoa ho etsa mosebetsi o matla oa matla, kapa haeba tsamaiso e fetoha nakong ea ts'ebetso e tloaelehileng. Sena se fa mosebelisi tsela e betere ho feta Maximum Speed ​​​​ho fokotsa tlhahiso ea pompo ea bona. Haeba tsamaiso e se e thibelang haholo, joale pompo e ntse e khona ho ba le litekanyetso tse phahameng tsa phallo ho feta kamoo e neng e ka ba kateng haeba mosebedisi a ne a sebelisitse moeli oa lebelo, empa khatello e ntse e lekanyelitsoe moo mosebedisi a neng a hloka hore e fokotsehe.
Khatello ke hlooho ea tsamaiso eohle, kahoo ke sehlahisoa sa khatello ea ho hula le khatello ea ho tsoa. Theko e baloang e lekana le Total Dynamic Head (TDH). Boleng bona bo kanna ba se tsamaellane le khatello ea sesefa, hobane ke TDH ka mose ho pompo eseng khatello ea lehae ea sefe.
Ha pompo e ntse e sebetsa Lenaneo la Phallo, e tla lula e leka ho finyella phallo e behiloeng ho sa tsotellehe hore na ho hlophisoa ha tsamaiso ke eng. Haeba khatello ea tsamaiso e fetoha nakong ea ho matha (e kang ho roala litšila, kapa ho fetola boemo ba valve ka letsoho), koloi e fetola RPM ea motlakase ho boloka lebelo le tsitsitseng la phallo.
Maemong a mang lebelo la enjene le sa tsoa kōptjoa le tla eketsa khatello ea ho tsoa e le ho boloka sekhahla sa phallo se kopiloeng. Ha u ntse u boloka lebelo la phallo, koloi e tla lula e le ka har'a khatello le meeli ea lebelo e behiloeng ka har'a menu ea Min / Max. Haeba pompo e kopana le e 'ngoe ea meeli, e tla tsoela pele ho sebetsa moeling' me leseli la temoso le tla khantša. Temoso ea moeli e tla hlahisoa ka tlase ho skrine ea li-drive's keypad e bontšang hore sekhahla sa phallo se kopiloeng ha se fihlellehe le hore na ke moeli ofe oo koloi e kenang ho oona.
Ha pompo e ntse e sebetsa Lenaneo la Lebelo, koloi ha e hlokomele phallo kapa meeli ea khatello ka ho iketsetsa.
Likarolo tsena li hloka ho lumelloa ho menu ea Min/Max.
Ho Seta Khatello e Phahameng ea Sisteme:

1. Sheba hore na LED e nang le matla a matala e butse.
2. Tobetsa Menu.
3. Tobetsa Khetha ho khetha "Settings".
4. Sebelisa metsu ea Holimo kapa Tlase ho tsamaisetsa ho "Min/Max". Tobetsa Khetha.
5. Sebelisa metsu ea Holimo kapa Tlase ho tsamaisetsa ho "Seta Khatello e Phahameng".
6. Tobetsa Kgetha ho fetola tlhophiso. Sekhesa se tla hlaha kholomong ea linomoro tsa pele (tse ling).
7. Tobetsa metsu ea Holimo kapa Tlase ho hlophisa maemo a phahameng a phallo ho tloha ho 1 ho isa ho 50 PSI.
8. Tobetsa Boloka ho boloka. Ho hlakola, tobetsa Khutlela ho tsoa molemong oa ho fetola ntle le ho boloka.
9. Tobetsa Morao ho tsoa.

Beha Moedi oa Khatello bakeng sa Lenaneo la Lebelo
Ha khatello ea khatello e ntse e sebetsa neng kapa neng ha pompo e sebetsa mofuta oa Phallo ea lenaneo, moeli oa khatello o emisoa ka ho sa feleng ha o tsamaisa pompo ka mokhoa o tsitsitseng oa lebelo. Ho nolofalletsa tšobotsi ena ho tla etsa bonnete ba hore koloi e shebile khatello ea tsamaiso ha e sebetsa ka mokhoa o tsitsitseng oa lebelo hape.

1. Sheba hore na LED e nang le matla a matala e butse.
2. Tobetsa Menu.
3. Tobetsa Khetha ho khetha "Settings".
4. Sebelisa metsu ea Holimo kapa Tlase ho tsamaisetsa ho "Min/Max".Tobetsa Khetha.
5. Sebelisa metsu ea Holimo kapa Tlase ho tsamaisetsa ho "Moedi oa ho Hatisa (Lebelo)".
6. Tobetsa Khetha ho tsamaisa cursor holim'a "Holofetse".
7. Tobetsa le metsu ea Holimo kapa Tlase ho e fetolela ho "Enabled".
8. Tobetsa Boloka ho boloka. Ho hlakola, tobetsa Khutlela ho tsoa molemong oa ho fetola ntle le ho boloka.
9. Tobetsa Morao ho tsoa.

Aterese ea Pompo
Sebelisa tlhophiso ena haeba pompo ea hau e hokahane ka boema-kepe ba RS-485 COM ho sistimi ea othomathiki ea Penair.
Aterese ea kamehla ea pompo ke #1 mme e hloka ho fetoloa feela ha ho na le pompo e fetang e le 'ngoe ho sistimi ea othomathike. Fetola aterese ho lumella sistimi ea othomathike ho romella taelo ho pompo e nepahetseng. Aterese ea pompo e ka behoa ho tloha ho 1-16.
Sheba buka ea automation system bakeng sa lintlha tse ling mabapi le mokhoa oa ho hokela le ho sebelisa sistimi ea othomathike ka pompo ea hau e feto-fetohang ea lebelo.

1. Etsa bonnete ba hore matla a tala a LED a butsoitse 'me pompo e emisitsoe.
2. Tobetsa Menu.
3. Tobetsa Khetha ho khetha "Settings".
4. Sebelisa metsu ea Holimo kapa Tlase ho tsamaisetsa ho "Sesebediswa".
   Tlanya Khetha.
5. Sebelisa metsu ea Holimo kapa Tlase ho tsamaisetsa ho "Pump Address". Tobetsa Khetha.
6. Tobetsa metsu ea Holimo kapa Tlase ho fetola nomoro ea aterese ho tloha ho 1-16.
7. Tobetsa Boloka ho boloka. Ho hlakola liphetoho life kapa life, tobetsa Khutlela ho tsoa ntle le ho boloka.
8. Tobetsa Morao ho tsoa.

Beha Phapang ea Screen
Phapang ea kamehla ea skrine ea LCD ke 3.
Maemo a ho bapisa skrineng a ka fetoloa ho tloha ho li-unit tse 1 ho isa ho tse 5 bakeng sa maemo a mabone a tlase kapa a phahameng.
Tlhokomeliso: Liphetoho tlhophisong ea phapang ha li ntlafatse hang-hang. Liphetoho ho litlhophiso tsena li tlameha ho bolokoa pele boemo ba phapang bo fetoha.

1. Sheba hore na LED e nang le matla a matala e butse.
2. Tobetsa Menu.
3. Tobetsa Khetha ho khetha "Settings".
4. Sebelisa motsu oa Holimo kapa Tlase ho tsamaisetsa ho "Sesebediswa".
   Tlanya Khetha.
5. Sebelisa motsu oa Holimo kapa Tlase ho tsamaisetsa ho "Contrast Level."
6. Tobetsa Khetha. Skrine e tla bonts'a nomoro ea hajoale ea tlhophiso ea phapang. Sebelisa Holimo kapa Tlase ho fetola nomoro.
7. Tobetsa Boloka ho boloka. Ho hlakola liphetoho life kapa life, tobetsa Khutlela ho tsoa ntle le ho boloka.
8. Tobetsa konopo ea Morao ho tsoa.

Beha Puo ea Panopo ea Taolo

1. Sheba hore na LED e nang le matla a matala e butse.
2. Tobetsa Menu ebe o tobetsa Khetha ho khetha "Settings".
3. Sebelisa metsu ea Holimo kapa Tlase ebe u tsamaisetsa ho "Sesebediswa".
   Tlanya Khetha.
4. Sebelisa metsu ea Holimo kapa Tlase ho tsamaisetsa ho "Khetha Puo". Tobetsa Khetha.
5. Sebelisa metsu ea Holimo kapa Tlase ho khetha puo eo u e batlang.
6. Tobetsa Boloka ho khetha puo ea phanele ea taolo.
   Ho hlakola liphetoho life kapa life, tobetsa Khutlela ho tsoa ntle le ho boloka.
7. Tobetsa Morao ho tsoa.

Seta Unit Mocheso
Setting ea kamehla ke Fahrenheit (°F). Pompo e ka hlophisoa hore e be Celsius (°C) kapa Fahrenheit (°F).

1. Sheba hore na LED e nang le matla a matala e butse.
2. Tobetsa Menu.
3. Tobetsa Khetha ho khetha "Settings".
4. Sebelisa metsu ea Holimo kapa Tlase ho tsamaisetsa nthong ea "Sesebediswa". Tobetsa Khetha.
5. Sebelisa metsu ea Holimo kapa Tlase ho tsamaisetsa ho "Lisebelisoa tsa Mocheso". Tobetsa Khetha.
6. Sebelisa metsu ea Holimo kapa Tlase ho khetha Celsius (°C) kapa Fahrenheit (°F).
7. Tobetsa Boloka ho boloka. Ho hlakola liphetoho life kapa life, tobetsa Khutlela ho tsoa ntle le ho boloka.
8. Tobetsa Morao ho tsoa.

Tšireletso ea Password
Boemo ba mantlha bakeng sa ts'ireletso ea phasewete bo holofetse.
Ha tšobotsi ena e nolofalitsoe, ponts'o ea pompo e tla hlahisa phasewete pele e lumella ho fihlella phanele ea taolo le likonopo.
Phasewete e kentsoeng ke motsoako ofe kapa ofe oa linomoro tse 'ne (4).

• Pompo e ka emisoa ka linako tsohle ka ho tobetsa Qala / Emisa, leha ts'ireletso ea password e nolofalitsoe.
• Haeba pompo e emisoa, pompo e ke ke ea buloa hape ka Qala / Emisa ha e ntse e sebetsa ka mokhoa oa matsoho.
• Ho tobetsa Qala/Emisa ha pompo e koetsoe ho tla e khutlisetsa ho Running Cycles Mode 'me e sebetse ka nako e latelang e reriloeng. Haeba nako ea hona joale e le ka har'a nako e behiloeng, pompo e tla tsamaisa lebelo le reriloeng.
• Lits'ebetso tsohle ho kenyeletsoa le mananeo li koetsoe ho Mokhoa oa Ts'ireletso ea Lekunutu.
• Skrine e tla bala "Enter Password" haeba konopo efe kapa efe ntle le konopo ea Qala / Emisa e tobetsoe
• Letšoao la senotlolo le bonts'itsoeng lehlakoreng le ka holimo le letšehali la skrine ha Tšireletso ea Password e buletsoe.

Ho beha phasewete

1. Sheba hore na LED e nang le matla a matala e butse.
2. Tobetsa Menu. Tobetsa Khetha ho khetha "Settings".
3. Sebelisa motsu oa Holimo kapa Tlase ho tsamaisetsa ho "Sesebediswa".
   Tlanya Khetha.
4. Tobetsa motsu oa Holimo kapa Tlase ho tsamaisetsa ho "Password".
   Tlanya Khetha.
5. Setting ea kamehla ke "Disabled". Tobetsa Holimo kapa
   Motsu o tlase ho fetola litlhophiso ho "Enabled".
   Tobetsa Boloka ho boloka.
6. Tobetsa motsu oa Down. "Password Timeout" e tla hlahisoa. Nako ea kamehla ea feme ke hora e le 'ngoe.
   Sena se bolela IntelliFlo®
   VSF E feto-fetohang Lebelo le
   Phallo Pump e tla kena mokhoeng oa Ts'ireletso ea Lekunutu hora e le 1 ka mor'a hore konopo ea ho qetela ea phanele ea taolo e hatisoe.
7. Tobetsa Kgetha ho kenya mokgwa wa ho edita. Sebelisa motsu oa Holimo kapa Tlase ho hlophisa tlhophiso ea nako ho tloha motsotsong o le mong ho isa ho lihora tse 1 ebe o tobetsa Boloka ho boloka litlhophiso.
8. Tobetsa motsu oa Down ebe o tobetsa Khetha ho "Set Password" ho fetola maemo.
9. Tobetsa metsu e ka ho le letšehali kapa e ka ho le letona ho tsamaisa sesupa ebe o tobetsa Motsu oa Holimo kapa Tlase ho fetola nomoro ea lekunutu hore e be boemong boo u bo batlang.
10. Tobetsa Boloka ho boloka. Ho hlakola liphetoho life kapa life, tobetsa Khutlela ho tsoa ntle le ho boloka.

Ho kenya phasewete

1. Tobetsa konopo efe kapa efe (ntle le likonopo tsa lenaneo) ho etsa hore skrine e fumane phasewete.
2. Ho kenya phasewete, sebelisa metsu e ka ho le letšehali le ea ho le letona ho tsamaisa khesa le konopo ea Motsu oa Holimo le Tlase ho tsamaisetsa nomorong ebe o tobetsa Save ho netefatsa.

Seta Ramping Rate
Sekhahla sa hore koloi e fetola lebelo la enjene e ka fokotsoa bakeng sa ts'ebetso e bonolo. Tlhophiso ena e eketsa kapa e fokotsa hore na pompo e ka potlaka hakaeamp hodimo kapa tlase pakeng tsa mabelo a mabedi. Litefiso li ka hlophisoa le ho lokisoa bakeng sa rampho phahamisa le rampho theoha ka bonngoe.
Haeba konopo ea Start/Stop e ka hatelloa, enjene e tla ema hang-hang 'me e ke ke ea latela r e hlophisitsoengamping rate. Litlhophiso tsa kamehla ke tsa Fast, e leng IntelliFlo r ea setsoamping rate. Medium e tla nka nako e telele habeli ho fetola lebelo, 'me Butle o tla nka nako e telele ka makhetlo a mararo.

1. Sheba hore na LED e nang le matla a matala e butse.
2. Tobetsa Menu.
3. Tobetsa Khetha ho khetha "Settings".
4. Sebelisa motsu oa Holimo kapa Tlase ho tsamaisetsa ho "Sesebediswa".
   Tlanya Khetha.
5. Sebelisa motsu oa Holimo kapa Tlase ho tsamaisetsa ho “Rampka”.
   Tlanya Khetha.
6. Sebelisa motsu oa Holimo kapa Tlase ho tsamaisetsa ho “Ramp Holimo”.
   Tobetsa Khetha 'me u sebelise motsu oa Holimo kapa Tlase ho khetha pakeng tsa "Fast", Medium kapa "Slow". Tobetsa Boloka.
7. Sebelisa motsu oa Holimo kapa Tlase ho tsamaisetsa ho “Ramp Tlase”. Tobetsa Khetha 'me u sebelise motsu oa Holimo kapa Tlase ho khetha pakeng tsa "Fast", Medium kapa "Slow". Tobetsa Boloka.

Mekhoa e sebetsang ea Pump
Pompo ena e ka hlophisoa ka mekhoa e meraro e fapaneng:
Mananeo 1-4 a ka hlophisoa ka mekhoa eohle e meraro.
Mananeo 5-8 a ka hlophisoa feela ka mokhoa oa Kemiso kaha ha ho na likonopo sebakeng sa taolo bakeng sa Mananeo 5-8. Litlhophiso tsa kamehla bakeng sa Mananeo 5-8 ke "Ho holofetse".Bukana
E abela lebelo kapa phallo ho e 'ngoe ea likonopo tse 'ne tsa Lenaneo ho phanele ea taolo. Mokhoa ona o ka sebelisoa feela bakeng sa mananeo a 1-4. Mananeo 1 le 2 ke Manual ka ho sa feleng.
Ho sebetsa ka mokhoa oa Manual, tobetsa e 'ngoe ea likonopo tse' nè tsa lenaneo ebe o tobetsa konopo ea Qala/Emisa. Pompo e tla tsamaisa lebelo le fanoeng kapa phallo e abetsoeng konopo ea lenaneo.
Nako ea Lehe
Mananeo 1-4 a ka hlophisoa hore a tsamaee ka lebelo le itseng kapa phallo le ka nako e telele hang ha konopo ea lenaneo e tobetse.
Mananeo 3 le 4 ke Li-Egg Timers ka ho iketsa. Haeba u lakatsa mokhoa o fapaneng oa ts'ebetso, mananeo a 3 le 4 a ka fetoloa ho "Manual mode" ho menu ea taolo.
Ho sebetsa ka mokhoa oa Egg Timer, tobetsa konopo ea lenaneo ebe o tobetsa Qala/Emisa. Pompo e tla tsamaisa sebaka seo bakeng sa nako e behiloeng ebe e tima.
Kemiso
Mananeo 1-8 a qala mme a emisa ka nako e itseng nakong ea lihora tse 24. Lebelo kapa phallo e hlophisitsoeng ka mokhoa oa Shejule e tla fetisa lebelo kapa phallo efe kapa efe e khethiloeng ka letsoho hang ha taelo e latelang ea Kemiso e qala.
Beha Mananeo ka Mokhoa oa Manual (Mananeo a 1-4 Feela)

1. Tobetsa Menu.
2. Sebelisa metsu ea Holimo kapa Tlase ho tsamaisetsa ho "Program 1-8", ebe o tobetsa Khetha.
3. Sebelisa metsu ea Holimo kapa Tlase ho fumana lenaneo (1-4) leo u lakatsang ho le hlophisa, ebe u tobetsa Khetha.
4. "Mokhoa oa Ts'ebetso" o tla hlaha. Tobetsa Khetha 'me u sebelise motsu oa Holimo kapa Tlase ho tsamaisetsa ho "Manual". Tobetsa Boloka.
5. Sebelisa motsu oa Holimo kapa Tlase ho tsamaisetsa ho "Set Type".
   Tobetsa Khetha 'me u sebelise motsu oa Holimo kapa Tlase ho khetha pakeng tsa "Speed" kapa "Flow". Tobetsa Boloka.
6. Sebelisa motsu oa Holimo kapa Tlase ho tsamaisetsa ho "Seta Lebelo/ Phallo". Tobetsa Khetha 'me u sebelise motsu oa Holimo kapa Tlase ho lokisa li-setting tsa lebelo kapa phallo.
7. Tobetsa Boloka ho boloka lebelo le lecha kapa litlhophiso tsa ho phalla.

Beha Mananeo ka Mokhoa oa Egg-Timer (Mananeo a 1-4 Feela)

1. Tobetsa Menu.
2. Sebelisa metsu ea Holimo kapa Tlase ho tsamaisetsa ho "Program 1-8", ebe o tobetsa Khetha.
3. Sebelisa metsu ea Holimo kapa Tlase ho fumana lenaneo (1-4) leo u lakatsang ho le hlophisa, ebe u tobetsa Khetha.
4. "Mokhoa oa Ts'ebetso" o tla hlaha. Tobetsa Khetha 'me u sebelise motsu oa Holimo kapa Tlase ho tsamaisetsa ho "Egg Timer".
   Tobetsa Boloka.
5. Sebelisa motsu oa Holimo kapa Tlase ho tsamaisetsa ho "Set Type".
   Tobetsa Khetha 'me u sebelise motsu oa Holimo kapa Tlase ho khetha pakeng tsa "Speed" kapa "Flow". Tobetsa Boloka.
6. Sebelisa motsu oa Holimo kapa Tlase ho tsamaisetsa ho "Seta Lebelo/ Phallo". Tobetsa Khetha 'me u sebelise motsu oa Holimo kapa Tlase ho lokisa li-setting tsa lebelo kapa phallo. Tobetsa Boloka.
7. Joale tobetsa konopo ea Down ("Egg Timer Duration" e tla hlaha) ebe o tobetsa Khetha ho fetola. Sebelisa metsu ea Holimo kapa Tlase ho fetola nako.
8. Tobetsa Boloka ho boloka nako e ncha.

Beha Mananeo 1-8 ho Mokhoa oa Kemiso
Ka mokhoa oa Kemiso, Mananeo 1-8 a ka hlophisoa ho tsamaisa lebelo le itseng kapa ho phalla ka nako e itseng ea letsatsi.
Ho tsamaisa lebelo le reriloeng kapa phallo, tobetsa Qala/Emisa.
Skrine e tla bonts'a "Lunning Schedules" ha e se e loketse ho tsamaisa lebelo / phallo e reriloeng. Haeba Qala / Emisa e hatelloa ha lebelo le reriloeng / phallo e ntse e sebetsa, pompo e tla emisa ho tsamaisa lebelo / phallo e reriloeng. Pompo e ke ke ea tsoela pele ho tsamaisa lebelo / phallo e hlophisitsoeng ho fihlela konopo ea Qala / Stop e hatelloa hape.

1. Tobetsa Menu.
2. Sebelisa metsu ea Holimo kapa Tlase ho tsamaisetsa ho "Program 1-8", ebe o tobetsa Khetha.
3. Sebelisa metsu ea Holimo kapa Tlase ebe o tobetsa Khetha bakeng sa lebelo leo u lakatsang ho le beha le ho le hlophisa.
4. "Mokhoa oa Ts'ebetso" o tla hlaha. Tobetsa Khetha 'me u sebelise motsu oa Holimo kapa Tlase ho tsamaisetsa ho "Shejule".
   Tobetsa Boloka.
5. Sebelisa motsu oa Holimo kapa Tlase ho tsamaisetsa ho "Set Type".
   Tobetsa Khetha 'me u sebelise motsu oa Holimo kapa Tlase ho khetha pakeng tsa "Speed" kapa "Flow". Tobetsa Boloka.
6. Sebelisa motsu oa Holimo kapa Tlase ho tsamaisetsa ho "Seta Lebelo/ Phallo". Tobetsa Khetha 'me u sebelise motsu oa Holimo kapa Tlase ho lokisa li-setting tsa lebelo kapa phallo.
7. Tobetsa Boloka ho boloka lebelo le lecha kapa litlhophiso tsa ho phalla.
8. Tobetsa motsu oa Down hape, "Nako ea ho Qala" e tla hlaha. Tobetsa Khetha - cursor e tla totobatsa kholomo ea motsotso.
9. Sebelisa motsu oa Holimo kapa Tlase ho fetola nako le motsu oa Leqele kapa le letona ho tsamaisa sesupa ho tloha metsotsong ho ea ho lihora.
10. Tobetsa Boloka ho boloka tlhophiso e ncha ea nako ea ho qala.
11. Tobetsa motsu o theoha - "Stop Time" e tla hlaha. Tobetsa Khetha. Pheta Mehato ea 8-9 ho beha nako ea ho emisa.
12. Tobetsa Boloka ho boloka setlama se secha sa nako ea ho emisa.
13. Tobetsa Qala/Emisa.

IntelliFlo® VSF Variable Speed ​​le Flow Pump e tla qala ebe e qala ho tsamaisa kemiso e hlophisitsoeng ka nako e behiloeng ea ho qala.
Ha o sebetsa ka mokgwa wa Shejule kapa wa Egg Timer, nako ya ho bala (T 00:01) e bontshang dihora le metsotso e setseng e tla bontshwa.
Lenaneo la Lenaneo la Kamehla ea Run
Mananeo a mabeli a ke ke a hlophisoa ka linako tse tšoanang tsa ho qala le ho emisa. Ho tsamaisa lenaneo ntle le ho emisa, seta nako ea ho Qala motsotso o le mong ka mor'a nako ea ho emisa.
ExampLe: Lenaneo le le leng le tla sebetsa le sa khaotse haeba le hlophisitsoe ka Nako ea ho Qala ea 8:00 AM le Nako ea Stop ea 7:59. AM.Hlokomela: Pompo e ke ke ea tsamaisa lebelo le reriloeng kapa ho phalla ho fihlela konopo ea Qala / Stop e hatelloa (LED on) ho beha pompo ka mokhoa oa Kemiso.
Kemiso ea Lenaneo le Reriloeng
Ha o sebelisa pompo ka mokhoa oa Kemiso ho bohlokoa ho boloka lenaneo le leng le le leng ka nako ea lona ea ho sebetsa. Haeba linako tsa mananeo li fetana pompo e tla beha mananeo pele joalokaha ho hlalositsoe ka tlase:
Kemiso ea lintho tse tlang pele ka tatellano e theoha ka tsela e latelang: Phallo e Phahameng ka ho Fetisisa » Phallo e tlase ka ho Fetisisa » Lebelo le Phahameng » Lebelo le tlase

• Ha manane a mabeli a lebelo KAPA a mabeli a phallo a kopana, pompo e tla tsamaisa lebelo le phahameng la RPM kapa GPM Flow ho sa tsotelehe hore na lenaneo le sebelisoa.
• Ha bobeli lebelo LE kemiso ea phallo ea lenaneo li kopana, pompo e tla tsamaisa lenaneo la phallo pele.
• Taelo ea tataiso kapa egg timer e nka mohlala ho feta kemiso e sebetsang. Taelo ea tataiso kapa egg timer e tla sebetsa ho fihlela e phethoa, ntle le haeba lenaneo le latelang la kemiso le etsahala kapa taelo e 'ngoe e fanoa.

Taolo ea Kantle
Ts'ebetso ena ke ea lebelo la mananeo kapa phallo e tla sebetsa ha IntelliComm® Communication Center e e romella taelo. Bakeng sa mohlalaample, Terminal 3 le 4 tsamaisong ea IntelliComm li tla lumellana le Lenaneo la Taolo ea Kantle #1. (5 le 6 ho Ext Ctrl #2).
Sebopeho sa Stop Delay se lumella mosebelisi ho hlophisa pompo ho tsamaisa Lenaneo ka mor'a hore Taolo ea Kantle e koetsoe. Sebopeho sena se ka sebelisoa ho fana ka nako ea ho pholisa pompo ka mor'a hore lets'oao la ho qala ho tsoa ho hitara e kentsoeng e koetsoe.
Lenaneo le leng le le leng le ka ba le Stop Delay ea metsotso e 1 ho isa ho e 10 e hlophisitsoeng.
Sebelisa tšobotsi ea Taolo ea Kantle ho hlophisa setsi sa motlakase sa sistimi ea IntelliComm.
Taolo ea kantle e ka boela ea sebelisoa bakeng sa ho tima pompo ka ho khetha "Pump Off" ha u khetha mokhoa oa ts'ebetso. Haeba lenaneo lena le hlahisoa ka taolo ea kantle, pompo e tla emisa ho sebetsa ha feela lenaneo le ntse le sebetsa. Karolo ena e ka ba molemo bakeng sa lits'ebetso tsa karabelo ea tlhoko e sebelisang IntelliComm ho buisana le pompo.
Ho fihlella lenane la External Control:

1. Sheba hore na LED e nang le matla a matala e butse.
2. Tobetsa konopo ea Menu.
3. Sebelisa motsu oa Holimo kapa Tlase ho tsamaisetsa ho "Ext. "Ctrl".
   Tlanya Khetha.
4. "Lenaneo la 1" le tla hlaha. Tobetsa Khetha ho kenya lenane la Lenaneo la 1.
5. "Mokhoa oa Ts'ebetso" o tla hlaha. Tobetsa Khetha 'me u sebelise metsu ea Holimo kapa Tlase ho khetha pakeng tsa "Enabled" kapa "Pump Off". Tobetsa Boloka.
   Tlhokomeliso: Lenaneo leo u lekang ho le hlophisa le tlameha ho lumelloa hore le tsoele pele ho menu.
6. Sebelisa motsu oa Holimo kapa Tlase ho tsamaisetsa ho "Set Type". Tobetsa Khetha.
7. Sebelisa motsu oa Holimo kapa Tlase ho khetha pakeng tsa "Speed" kapa "Flow". Tobetsa Boloka.
8. Sebelisa motsu oa Holimo kapa Tlase ho tsamaisetsa ho "Set Speed/Flow". Tobetsa Khetha 'me u sebelise motsu oa Holimo kapa Tlase ho lokisa li-setting tsa lebelo kapa phallo.
   Tobetsa Boloka.
9. Haeba o sa lakatse ho etsa lenaneo la ho lieha ho emisa, tsoela pele ho mohato oa 11. Haeba u lakatsa ho hlophisa tieho ea Emisa, tobetsa konopo ea Holimo kapa Tlase ho tsamaisetsa ho "Emisa ho Lieha". Tobetsa Khetha.
10. Sebelisa metsu ea Holimo kapa Tlase ho fetola maemo a Stop Delay. Stop Delay e ka beoa ho tloha metsotso e 0 (e holofalitsoe) ho isa ho metsotso e 10.
11. Tobetsa Save ho boloka li-setting.
12. Tobetsa Morao ho khutlela ho seta Lenaneo la 2.
13. Sebelisa motsu oa Holimo kapa Tlase ho tsamaisetsa ho "Lenaneo la 2".
14. Pheta Mehato ea 4 ho isa ho ea 11 ho theha Lenaneo la 2, la 3 le la 4.

Khefutso
Karolo ea Time Out e thibela IntelliFlo® VSF Variable Speed ​​le Flow Pump hore e se ke ea sebetsa ka lebelo le hlophisitsoeng kapa ho phalla ka nako e behiloeng e ka fetoloang ho menu. Karolo ea Time Out e hlahisoa ka lihora le metsotso (Hrs:Mins).
Hang ha Time Out e felile, pompo e tla khutlela mokhoeng oa eona oa pele oa ts'ebetso, Start/Stop LED e tla bonesoa 'me e se e loketse ho bulela ka nako e latelang e reriloeng.
Ho fihlella lenane la Time Out:

1. Sheba hore na LED e nang le matla a matala e butse.
2. Tobetsa Menu.
3. Sebelisa metsu ea Holimo kapa Tlase ho tsamaisetsa ho "Features", ebe o tobetsa Khetha.
4. Tobetsa Khetha ho khetha "Timeout".
5. "Timeout Duration" e tla hlaha. Tobetsa Kgetha ho totobatsa kholomo ya metsotso.
6. Tobetsa motsu oa Leqeleng ho isa sesupa kholomong ea lihora. Nako ea nako e ka beoa ho tloha motsotso o le mong ho isa ho lihora tse 1.
7. Tobetsa Boloka ho boloka tlhophiso
   Ela hloko: Ho hlakola liphetoho leha e le life, tobetsa Khutlela ho tsoa ntle le ho boloka.
8. Tobetsa Morao ho tswa ho menu.

Hloekisa ka Potlako
Tšobotsi ena e ka sebelisoa ho eketsa lebelo la pompo kapa ho phalla ka sepheo sa ho hloekisa, ho hloekisa, ho eketsa lik'hemik'hale, ka mor'a sefefo bakeng sa bokhoni bo eketsehileng ba skimming.
Tobetsa konopo ea Quick Clean (LED on) ebe o qala/Emisa ho qala. Ha potoloho ea Quick Clean e felile, pompo e tla tsoela pele ka linako tse tloaelehileng ebe e khutlela mokhoeng oa "Shejule".
Ho fihlella lenane la Quick Clean:

1. Sheba hore na LED e nang le matla a matala a teng le hore pompo e emisitsoe.
2. Tobetsa Menu.
3. Sebelisa metsu ea Holimo kapa Tlase ho tsamaisetsa ho "Features", ebe o tobetsa Khetha.
4. Tobetsa motsu o ka tlase ebe o tobetsa Khetha bakeng sa "Quick Clean".
5. Tobetsa Khetha ho khetha "Set Type". Sebelisa motsu oa Holimo kapa Tlase ho khetha pakeng tsa "Speed" kapa "Flow". Tobetsa Boloka.
6. Sebelisa motsu oa Holimo kapa Tlase ho tsamaisetsa ho "Set Speed/Flow". Tobetsa Khetha 'me u sebelise motsu oa Holimo kapa Tlase ho lokisa li-setting tsa lebelo kapa phallo.
   Tobetsa Boloka.
7. Tobetsa Boloka ho boloka lebelo kapa tlhophiso ea phallo.
8. Tobetsa motsu o ka tlase ebe o tobetsa Khetha bakeng sa "Nako ea Nako".
9. Sesupa se tla totobatsa kholomo ea metsotso.
   Sebelisa metsu ea Holimo kapa Tlase ho fetola nako ho tloha motsotsong o le mong ho isa ho lihora tse 1.
10. Tobetsa Boloka ho boloka nako.
11. Tobetsa Morao ho tswa ho menu.

Litlhophiso tsa kamehla tsa Priming li ENABLED. Tlhophiso ena e lumella pompo hore e ipone ka bo eona haeba e kentsoe bakeng sa ho qala.
Karolo ea priming e eketsa lebelo la pompo ho 1800 RPM mme e emisa metsotsoana e meraro (3). Haeba ho na le phallo e lekaneng ea metsi ka har'a basketeng ea pompo, pompo e tla tsoa mokhoeng oa ho qala 'me e tsamaise lebelo leo e laetsoeng.
Haeba phallo ea metsi e sa lekana, lebelo la pompo le tla eketseha ho ea ho "Priming Speed" mme le lule bakeng sa nako ea ho lieha ho qala (metsotsoana e 20 ea kamehla). Haeba ho na le phallo e lekaneng ea metsi ka har'a basketeng ea pompo ka nako ena, e tla tsoa ka mokhoa oa priming le ho fetela lebelo le laetsoeng.
Haeba ho ntse ho e-na le phallo e sa lekaneng ka har'a baskete ea pompo, joalo ka ha ho khethoa ke Priming Range setting, pompo e tla leka ho qala ka "Priming Speed" bakeng sa nako e behiloeng ho menu ea "Maximum Priming Time".
Hang ha pompo e fihletse boemo bo holimo, e tla qala ts'ebetso e tloaelehileng ka mor'a ho lieha ho qala pele.
Tlhokomeliso: Hoa khoneha ho beha "Maximum Speed" tlase haholo hore pompo e ka qala hantle. Lebelo le Leholo le tla fokotsa Lebelo la Priming, ntle le ketsahalong e le 'ngoe. Haeba Lebelo le Phahameng le behiloe ka tlase ho lebelo le tlaase ka ho fetisisa la Priming Speed ​​(2400 RPM) joale pompo e tla feta Maximum Speed ​​ha karolo ea priming e ntse e sebetsa. Sena se thibela pompo hore e se ke ea ba le bothata ba ho qala haeba lebelo le phahameng le behiloe tlase. Haeba sena e le bothata, priming e ka emisoa ho Priming Menu.

Litaba tsa Priming
E holofetse/ E nolofaditswe
Boemo ba mantlha: ENABLED
E lumella IntelliFlo® VSF Variable Speed ​​le Flow Pump hore e ipone ka bo eona haeba pompo e lokiselitsoe ho qala. Pompo e tla potlakisa ho fihla ho 1800 RPM ebe e emisa metsotsoana e meraro (3) - haeba ho na le metsi a lekaneng ka basketeng, pompo e tla tsoa ka mokhoa oa priming mme e tsamaise lebelo le laetsoeng.
Priming Speed
Boemo ba mantlha: 3450 RPM
Lebelo la priming le ka beoa lipakeng tsa 2400 RPM le 3450 RPM. Haeba pompo e le holim'a thepa ea thepa e haufi le boemo ba metsi, e ke ke ea hloka ho matha ka 3450 RPM ho qala ka katleho. Setlhophiso se ka theoleloa ho thibela ho matha ka lebelo le holimo ho feta kamoo ho hlokahalang.
Lintlha tsa letsatsi le letsatsi (ke hore, khatello ea tikoloho, mocheso oa metsi/moea, bongata ba metsi a bolokoang ho tloha nakong e fetileng) li ka ama ts'ebetso ea pele. Ka lebaka la maemo a fetohang khafetsa a lintlha tsena lebelo la priming le lokela ho beoa holimo ho lekana ho amohela liphetoho tsa tikoloho le tsa mochini ho netefatsa hore pompo e ka qala ka katleho. Ho fumana lebelo le sebetsang hantle le le sebetsang hantle bakeng sa litlhoko tsa hau tse ikhethileng ho ka hloka tlhahlobo e hlokolosi le tlhahlobo ea ts'ebetso ea priming.
Nako e phahameng ea ho qala
Kamehla: metsotso e 11
Nako e phahameng ea priming e ka beoa ho tloha metsotso e 1 - 30. Setlhophiso sena ke nako eo pompo e tla leka ho e qala pele e fana ka phoso ea ho qala. Haeba sena se etsahala, tlatsa baskete ea pompo ka metsi ebe u qala pompo hape.
Priming Range
Ntho ea kamehla: 5
Mofuta oa priming o ka beoa ho tloha ho 1-10. Ha lebelo le le lenyenyane, ho na le metsi a mangata ao pompo e lokelang ho tsamaea ho eona ho bona hore e hloekisitsoe. Libakeng tse kholoanyane, pompo e tla lemoha hore e hloekisitsoe ka ho feletseng ha e ntse e tsamaisa metsi a fokolang. Haeba marang-rang a behiloe holimo haholo, pompo e ka tsoa ho Priming mode pele e qala ka botlalo. Lebelo le tla ikamahanya le lebelo la sete ea priming hobane litefiso tsa phallo ea pompo li tla ba tlase ka lebelo le tlase.
Ho lieha ho qala
Kamehla: metsotsoana e 20
Ho lieha ho qala ho ka setoa ho tloha motsotsoana o le mong ho isa ho metsotso e 1.
Ha pompo ramps ho lebelo le feletseng la priming ka boiteko ba ho theha ts'ebetso ea pele, ho lieha ha priming ho lumella pompo hore e sebetse ka lebelo leo bakeng sa nako e eketsehileng e behiloeng pele e tsoela pele ho lenaneo le kōptjoang kapa le reriloeng.
Ho lahleheloa ke Prime
Kamehla: E lumelletsoe
Tšobotsi ena e lumella pompo hore e lemohe maemo a sa lebelloang a phallo e tlase kapa a se nang phallo ha e ntse e tsamaisa lenaneo.
Bakeng sa mohlalaample, pompo e tla ema motsotso o le mong (1) ka mor'a ho lemoha hore e lahlehetsoe ke boemo ba eona ka tšohanyetso. Ka mor'a khefutso ena, pompo e tla leka ho qala, 'me haeba e atleha, e tla tsoelapele ho sebetsa ka mokhoa o hlophisitsoeng. Haeba priming e sa atlehe pompo e tla tsoelapele ho leka ho qala, ka ts'ebetso e tloaelehileng ea ho qala, ho fihlela ho fihleloa ho finyelloa kapa phoso ea priming e hlaha mme e bonts'oa.
MENU
TS'ELISO
Pump Menu: Ho qala
Ho beha likarolo tsa Priming

1. Tobetsa Menu.
2. Sebelisa motsu o tlase ho ea ho "Priming" ebe o tobetsa Khetha.
3. Feme ea kamehla e hlophisitsoe ho qala "Enabled".
   Ho tima, tsamaisetsa ho "Disabled" ebe o tobetsa Khetha.
   Tlhokomeliso: Likarolo tsohle tsa priming li fumaneha feela ha priming e "nobletsoe".
4. Tobetsa Boloka haeba u fetotse tlhophiso - sena se tla boloka khetho.
5. Tobetsa motsu oa Down ho tsamaisetsa ho "Set Speed".
   Tobetsa Kgetha ho edita.
6. Sebelisa metsu ea Holimo kapa Tlase ho fetola litlhophiso tsa lebelo. Tobetsa Boloka.
7. Tobetsa Down ho tsamaisetsa ho "Max Priming Duration". Tobetsa Kgetha ho edita.
8. Sebelisa metsu ea Holimo kapa Tlase ho fetola nako ho tloha motsotsong o le mong ho isa ho metsotso e 1. Tobetsa Boloka.
9. Tobetsa motsu oa Down ho ea ho "Priming Range". Tobetsa Kgetha ho edita.
10. Sebelisa metsu ea Holimo kapa Tlase ho fetoha ho tloha ho 1 ho ea ho 10. Ho eketsa palo ho lumella koloi ho lemoha ho qala ka ho phalla ho fokolang ha metsi.
11. Tobetsa Boloka.
12. Tobetsa motsu oa Down ho ea ho "Priming Delay". Tobetsa Kgetha ho edita.
13. Sebelisa metsu ea Holimo kapa Tlase ho fetoha ho tloha motsotsong o le mong ho isa ho metsotso e 1. Tobetsa Boloka.
    Ho eketsa nako ho etsa hore pompo e lule e le mocheng oa priming nako e telele.
14. Tobetsa motsu oa Down ho ea ho "Loss of Prime".
15. Boemo ba feme ke "Enabled". Ho tima, tobetsa Khetha ho edita le ho sebelisa motsu oa Down ho tsamaisetsa ho "Ho holofetse". Tobetsa Boloka.
16. Tobetsa Morao ho tsoa ho menu ea ho qala.

Ho thibela Priming ka Automation System
Ha IntelliFlo® VSF Variable Speed ​​le Flow Pump e hokahane le mokhoa oa ho laola othomathike, (IntelliTouch®, EasyTouch® kapa SunTouch® Control Systems), karolo ea priming pompong e ke ke ea emisoa ke sistimi ea taolo ea othomathiki e kantle feela. E tlameha hape ho holofala pompong ka boeona.
Haeba priming e nolofalitsoe ho qala, pompo e arabela ho litlhophiso tsa eona tsa ka hare pele e arabela litaelo tse tsoang tsamaisong ea tsamaiso ea mochine.
Haeba pompo e hokahane le sistimi ea taolo ea othomathike 'me priming e sa batloe, tima tšobotsi ea priming ho pompo le sistimi ea taolo ea othomathike.
Ho tima priming ka sistimi e ikemetseng:

1. Thibela karolo ea priming ho sistimi ea taolo ea othomathike setsing sa meroalo kapa ho sebelisa remoutu ea IntelliTouch kapa EasyTouch. (Sheba tataiso ea mosebelisi ea sistimi ea boiketsetso bakeng sa tlhaiso-leseling e eketsehileng).
2. Khaola thapo ea puisano ea RS-485 ka nakoana.
3. Bula sekwahelo ho phanele ea taolo ho tima priming pompong. Tobetsa Menu, sebelisa li-buttons tsa Motsu ho tsamaisa ebe u khetha "Priming", ebe u khetha "Ho holofetse" (feme ea feme e behiloe ho "Enabled").
   Tobetsa Morao ho tswa ho menu.
4. Hang ha priming e holofetse, kenya hape thapo ea puisano ea RS-485.

1. Tlosa priming ho sistimi ea taolo ea othomathike.
2. Hakolla thapo ea puisano ea RS-485.
3. Tlosa priming ho pompo.
4. Kenya hape thapo ea puisano ea RS-485.

MENU
MOSEBETSI OA MOCHESO
Menu ea Pompo: Mokhoa oa Mocheso
Sensor bakeng sa Thermal Mode e ka har'a koloi, ka holim'a enjene. Karolo ena e u lumella ho beha lebelo (4503450 RPM) kapa phallo (20-140 GPM) e tsamaeang ha IntelliFlo® VSF Variable Speed ​​le Flow Pump e kena Modeng oa Thermal. Boemo ba mocheso boo u lakatsang hore Thermal Mode e bo qale le bona bo ka hlophisoa.
BOHLOKOA: Karolo ena ke ea ts'ireletso ea pompo.
Se ke oa itšetleha ka sebopeho sa Thermal Mode bakeng sa tšireletso ea leqhoa ea letamo. Maemo a mang a ka etsa hore pompo e utloe mocheso o fapaneng le mocheso oa 'nete oa moea.
Sensor ea hau ea mocheso oa moea oa automation system e lokela ho sebelisoa ho utloa mocheso oa 'nete. Bakeng sa mohlalaample, haeba pompo e le ka tlung, mocheso oa kamore ha o bontše mocheso oa kantle. Pompo ha e utloe mocheso oa metsi.
Ho fihlella Lenaneo la Thermal Mode:

1. Sheba hore na LED e nang le matla a matala e butse.
2. Tobetsa Menu.
3. Sebelisa motsu oa Down ho ea ho "Thermal Mode" ebe o tobetsa Khetha.
4. Boemo ba feme bakeng sa Thermal Mode ke "Enabled". Ho tima Mode oa Thermal, tobetsa Khetha ho totobatsa "Enabled".
5. Tobetsa motsu oa Holimo - "E holofetse" e hlaha.
6. Tobetsa Boloka ho boloka.

Ho Seta Lebelo la Mokhoa oa Thermal / Phallo le Mocheso oa Pompo:
Hlokomela: Likarolo tsa Boemo ba Thermal li fumaneha feela ha Thermal Mode e "buletsoe".

1. Sebelisa metsu ea Holimo kapa Tlase ho tsamaisetsa ho "Set Type". Tobetsa Khetha.
2. Sebelisa motsu oa Holimo kapa Tlase ho khetha pakeng tsa "Speed" kapa "Flow". Tobetsa Boloka.
3. Sebelisa motsu oa Holimo kapa Tlase ho tsamaisetsa ho "Set Speed/Flow". Tobetsa Khetha.
4. Sebelisa motsu oa Holimo kapa Tlase ho lokisa lebelo kapa litlhophiso tsa phallo. Tobetsa Boloka.
5. Tobetsa motsu oa Down. "Mocheso" o tla hlaha. (Boleng bona bo tla etsa qeto ea hore na pompo e tla kenya Thermal Mode ho mocheso ofe, kamehla ke 40° F/4.4° C).
6. Tobetsa Kgetha ho edita. Sebelisa motsu oa Holimo kapa Tlase ho lokisa litlhophiso.
7. Tobetsa Boloka ho boloka boemo ba mocheso.
   Hlokomela: Ho hlakola liphetoho life kapa life, tobetsa Khutlela ho tsoa ntle le ho boloka.
8. Tobetsa Morao ho tsoa.

TLHOKOMELO

U SE KE UA bula pitsa ea sesefa haeba IntelliFlo® VSF Variable Speed ​​le Flow Pump e hloleha ho qala kapa haeba pompo e ntse e sebetsa ntle le metsi ka pitseng ea sesefa. Lipompo tse sebelisoang maemong ana li ka ba le khatello ea mouoane 'me li ka ba le metsi a chesang a chesang. Ho bula pompo ho ka baka kotsi e mpe ea motho. E le ho qoba monyetla oa ho tsoa kotsi, etsa bonnete ba hore li-valve tsa ho hula le ho ntša metsi li bulehile 'me mocheso oa pitsa ea strainer o pholile ho o ama, ebe o bula ka hloko e feteletseng.
Ho thibela tšenyo ea pompo le bakeng sa ts'ebetso e nepahetseng ea tsamaiso, hloekisa strainer ea pompo le libaskete tsa skimmer kamehla.
Basket Strainer Basket
Seroto sa sesefa (kapa 'pitsa ea sesefa'), se ka pel'a ntlo ea pompo. Seroto sa strainer se tlameha ho bolokoa se hloekile 'me se se na litšila. Hlahloba baskete ka sekwahelo ka holim'a ntlo. Etsa bonnete ba hore u sheba baskete ea sefa bonyane hang ka beke. Libaskete tsa li-strainer tse litšila li fokotsa ts'ebetso e ntle ea sefa le heater le ho beha khatello e sa tloaelehang mochining oa pompo.
Ho hloekisa Basket Strainer Basket

1. Tobetsa konopo ea Qala / Emisa holim'a pompo ebe o tima pompo ho sekheo sa potoloho. Hokela thapo ea puisano pompong.
2. Fokotsa khatello tsamaisong.
3. Fetola sekwahelo le selikalikoe sa ho notlela ho ea ka nako ea oache ebe o tlosa pompong.
4. Tlosa lithōle 'me u hlatsoe ka basketeng. Kenya sebaka sa baskete haeba e petsohile.
5. Khutlisa baskete ka tlung. Etsa bonnete ba hore o hokahanya notch e ka tlase ho basketeng le lekhopo le tlase ho volute.
6. Tlatsa pitsa ea pompo 'me u ikemisetse ho fihla koung ea ho kena ka metsi.
7. Hloekisa sekwahelo le reng ea ho notlela, O-ring, le bokaholimo bo koalang ba pitsa ea pompo.
   Tlhokomeliso: Ho bohlokoa ho boloka sekoahelo sa O-ring se hloekile ebile se tlotse hantle.
8. Kenya sekwahelo hape ka ho beha reng ya ho notlela le sekwahelo hodima pitsa. Etsa bonnete ba hore sekwahelo sa O-ring se behiloe hantle.
   Lula selikalikoe sa ho notlela le sekwahelo holim'a pompo ebe u retelehela ho ea ka nako ea oache ho fihlela mehala ea ho notlela e le perpendicular to inlet.
9. Tlosa matla "ON" ho sekheo sa potoloho.
   Hokela hape thapo ea puisano ho tsoa pompong.
10. Bula valve ea ho thusa moea ka holim'a sefe. Ema ka ntle ho sefe.
11. Emela ho fihlela khatello eohle e imolohile. Qala pompo.
12. Moea o tsoang ka har'a sefe ho fihlela metsi a tsitsitseng a tsoa ka har'a valve ea sefa ea moea. Koala valve ea liphallelo ea moea.

TSAMAISO ENA E SEBETSA KA TLAS'A KHATELLO E HAHOLO. Ha karolo efe kapa efe ea sistimi e potolohang (mohlala, Lock Ring, Pump, Filter, Valves, joalo-joalo) e sebetsoa, ​​moea o ka kena mochining ebe oa hatelloa. Moea o nang le khatello o ka etsa hore sekoahelo se arohane se ka bakang kotsi e tebileng, lefu kapa tšenyo ea thepa.
Ho qoba kotsi ena e ka hlahang, latela litaelo tse ka holimo.
Mariha
Ho sireletsa lisebelisoa tsa elektronike tsa pompo hore li se ke tsa senyeha, pompo e tla fetoha ho hlahisa mocheso o ka hare ha mocheso o theoha ka tlaase ho leqhoa haeba Thermal Mode e lumelloa. Karolo ea Thermal Mode e pompeng ha ea rereloa ho sireletsa lipeipi tsa sistimi hore li se ke tsa bata.

• Libakeng tse bonolo tsa boemo ba leholimo, ha ho ka ba le serame sa nakoana, tsamaisa thepa ea hau ea ho sefa bosiu bohle ho thibela leqhoa.
• U na le boikarabelo ba ho fumana hore na maemo a leqhoa a ka etsahala neng. Haeba maemo a leqhoa a lebeletsoe, nka mehato e latelang ho fokotsa kotsi ea tšenyo ea leqhoa. Tšenyo ea leqhoa ha e koaheloe tlas'a waranti.

Ho thibela tšenyo e hoamisoa, latela mekhoa e ka tlase:

1. Koala matla a motlakase bakeng sa pompo ho sekhechana sa potoloho.
2. Hlakola metsi ka ntle ho ntlo ea pompo ka ho ntša li-drain tse peli tse sothang ka har'a ntlo. Boloka li-plug ka basketeng ea pompo.
3. Koahela enjene ho e sireletsa puleng e matla, lehloa le leqhoa.

Hlokomela: Enjene e ka koaheloa nakong ea sefefo, polokelo ea mariha, joalo-joalo, empa ha ho mohla e sebetsang kapa e lebelletsoeng ho sebetsa. Le ka mohla u se ke ua phuthela koloi ka polasetiki kapa lisebelisoa tse ling tse thibelang moea nakong ea polokelo ea mariha.

HO SEBELISA

Kamehla hakolla motlakase ho IntelliFlo® VSF Variable Speed ​​le Flow Pump ho sekhechana sa potoloho 'me u hakolle thapo ea puisano pele u sebeletsa pompo. Ho hloleha ho etsa joalo ho ka baka lefu kapa kotsi e mpe ho batho ba sebeletsang, basebelisi kapa ba bang ka lebaka la ho tsukutloa ke motlakase. Bala litaelo tsohle tsa ts'ebeletso pele u sebetsa pompong.
U SE KE UA bula pitsa ea sesefa haeba pompo e hloleha ho qala kapa haeba pompo e ntse e sebetsa ntle le metsi ka pitseng ea sesefa. Lipompo tse sebelisoang maemong ana li ka ba le khatello ea mouoane 'me li ka ba le metsi a chesang a chesang. Ho bula pompo ho ka baka kotsi e tebileng ea motho. E le ho qoba monyetla oa ho tsoa kotsi, etsa bonnete ba hore li-valve tsa ho hula le ho ntša metsi li bulehile 'me mocheso oa pitsa ea strainer o pholile ho o ama, ebe o bula ka hloko e feteletseng.
Etsa bonnete ba hore u se ke ua ngopa kapa ua senya lifahleho tsa li-shaft tse bentšitsoeng; seal e tla dutla haeba difahleho di senyehile. Lifahleho tse bentšitsoeng le tse koetsoeng tsa tiiso li ka senyeha haeba li sa tšoaroe ka hloko.
Tlhokomelo ea Likoloi le Drive
Sireletsa mochesong

1. Tlosa motlakase letsatsing.
2. Sebaka leha e le sefe se kampetsoeng se tlameha ho ba le moea o pholileng ho thibela mocheso o feteletseng.
3. Fana ka ample cross ventilation.
4. Fana ka tumello ea bonyane ba lisenthimithara tse 3 ka morao ho fan ea motlakase bakeng sa ho potoloha hantle.

Sireletsa khahlanong le litšila

1. Sireletsa ho taba efe kapa efe e tsoang kantle ho naha.
2. Se ke oa boloka (kapa oa tšolla) lik'hemik'hale holim'a enjene kapa haufi le eona.
3. Qoba ho fiela kapa ho sisinya lerole haufi le enjene ha e ntse e sebetsa.
4. Haeba enjene e sentsoe ke litšila e ka hlakola waranti ea enjene.

Sireletsa khahlanong le mongobo

1. Sireletsa ho tloha ho fafatsa ho tsoelang pele kapa metsi a sa khaotseng a fafatsoang.
2. Sireletsa ho boemo ba leholimo bo feteletseng joalo ka likhohola.
3. Haeba lisebelisoa tsa motlakase li se li le metsi - li tlohele li omelle pele li sebetsa. U se ke ua lumella pompo hore e sebetse haeba e tletse metsi.
4. Haeba enjene e sentsoe ke metsi e ka hlakola waranti ea motlakase.
5. Etsa bonnete ba hore o koala sekoaelo sa letlapa la likonopo ka mor'a tšebeliso e 'ngoe le e 'ngoe.

Shaft Phetolo
The Shaft Seal e na le likarolo tse peli, tiiso ea ceramic e potolohang e kentsoeng ka har'a impeller le tiiso ea selemo e emeng ka har'a sealplate. Pompo e hloka ts'ebeletso e nyane kapa ha e hloke ho hang ntle le tlhokomelo e nepahetseng, leha ho le joalo, ka linako tse ling tiiso ea shaft e ka senyeha mme e tlameha ho nkeloa sebaka.
Hlokomela: Lifahleho tse bentšitsoeng le tse koetsoeng tsa tiiso li ka senyeha haeba li sa tšoaroe ka hloko.
Pompo ea ho qhaqha
Lisebelisoa tse hlokahalang:

• 3/32-inch Allen head wrench
• Li-wrenches tse peli (2) tse 9/16-inch tse bulehileng
• 1/4-inch Allen head wrench
• No. 2 Phillips hlooho screwdriver
• Wrench e fetolehang

Ho tlosa le ho lokisa motor subassembly, latela mehato e ka tlase:

1. Tima sekhechana sa potoloho ea pompo phanele e kholo.
2. Hakolla thapo ea puisano ea RS-485 pompong (haeba e hokahane le pompo).
3. Hlakola pompo ka ho tlosa li-drain plugs. Ha ho lisebelisoa tse hlokahalang.
4. Ntsha dikurufu tsa hlooho tse nne (4) tsa Phillips di hukung tse ka ntle tsa letlapa la dikonopo.
5. Tlosa letlapa la likonopo koloing 'me u le behe ka thōko sebakeng se sireletsehileng.
6. Tlosa li-screw tse tharo (3) tsa hlooho tsa Phillips, tse ka hare ho koloi, tse tiisang koloi ho ea ho enjene.
7. Tlosa koloi ka ho phahamisa holimo ho e arola ho enjene.
8. Sebelisa li-wrenches tsa 9/16-inch ho tlosa liboutu tse tšeletseng (6) tse ts'oereng ntlo (pitsa ea strainer / volute) ho subassembly e ka morao.
9. Ka bonolo hula li-halves tse peli tsa pompo ka thōko, u tlose subassembly e ka morao.
10. Sebelisa sekoahelo sa hlooho sa 3/32-inch sa Allen ho lokolla li-screw tse peli (2) tse fumanehang holim'a sesebelisoa.
11. Tšoara impeller sebakeng se sireletsehileng 'me u tlose screw lock ka ho sebelisa Phillips head screwdriver. Sekurufu ke khoele e ka letsohong le letšehali 'me e hlephisa ka tsela e eang ho oache.
    Sesebelisoa sa pompo se ka 'na sa e-ba le mahlakore a bohale a ka khonang ho khaola kapa ho ngoa matsoho a mosebedisi. Pentair e khothalletsa hore liatlana tsa tšireletso li apare ha u tšoere impeller nakong ea ho qhaqha le ho kopanya hape.
12. Sebelisa sekoahelo sa hlooho sa 1/4-inch sa Allen ho tšoara mochini oa motlakase. Moqomo oa motlakase o na le sokete ea sebopeho sa hex pheletsong e fumanehang bohareng ba sekoaelo sa fan.
13. Ho manolla sesupa-pele ho tloha mosikong, sotha sesupa-tsela ka nqane ho nako.
14. Tlosa liboutu tse 'nè (4) ho tloha poleiting ea tiiso ho ea mochineng, u sebelisa wrench ea 9/16-inch.
15. Beha seal plate se shebile fatše sebakeng se bataletseng 'me u tobetse setulong sa carbon spring.
16. Hloekisa seal plate, seal bore, le shaft ea enjene.

- Likarolo tse nang le litšoantšo tsa pompo view leqepheng le latelang -
Pompo ea ho hlophisa bocha

1. Ha u kenya setiiso sa shaft, sebelisa silicone sealant karolong ea tšepe pele u tobetsa poleiti ea tiiso joalokaha ho bontšitsoe. Tlhokomeliso: Sebelisa tlhokomelo e feteletseng ha u kenya sealant. Etsa bonnete ba hore ha ho sealant se amang holim'a poleiti ea tiiso kapa tiiso ea ceramic. Lumella sealant hore e fole bosiu bo le bong pele e kopanya hape.
2. Pele o kenya karolo e potolohang ea tiiso ho impeller, etsa bonnete ba hore impeller e hloekile.
   Sebelisa sesepa se bobebe le metsi ho tlotsa bokahare ba tiiso. Tobetsa tiiso ho impeller ka menoana ea matsoho 'me u hlakole lifahleho tsa ceramic le carbon ka lesela le hloekileng.
3. Khutlisa poleiti ea tiiso ho enjene.
4. Kenyelletsa sekoahelo sa senotlolo sa impeller (counterclockwise ho tiisa).
5. Kenya sephalli holim'a seal plate. Etsa bonnete ba hore lithakhisa tsa polasetiki le li-screw tse kenyang li hokahane.
   Tlhokomeliso: Netefatsa hore seal plate o-ring e hloekile ebile ha e na litšila.
6. Tlosa "diffuser o-ring" le seal plate gasket pele o kopanya hape.
7. Kopanya karolo ea motlakase sebakeng sa pompo ka ho sebelisa tse peli (2) ka liboutu bakeng sa ho tsamaisana hantle. Se ke oa tiisa liboutu ho fihlela liboutu tse tšeletseng (6) li se li le teng 'me menoana e tiisitsoe.
   Tlhokomeliso: Etsa bonnete ba hore seal plate gasket e lutse hantle ka hare ho kopano ea pompo. Seal gasket se ka phunyeletsoa pakeng tsa seal plate le pompo sa ntlo ha se tiisa likurufu tsena tse tšeletseng (6), ho thibela tiiso e nepahetseng le ho hlahisa ho lutla butle ha pompo e qala bocha.
8. Kenya koloi hape holim'a enjene.
9. Tlatsa IntelliFlo® VSF Variable Speed ​​le Flow Pump ka metsi.
10. Kenya hape sekwahelo sa pompo le selikalikoe sa ho notlela ka polasetiki.
    Sheba “Clening the Pump Strainer Basket” leqepheng la 21 bakeng sa lintlha tse qaqileng
11. Hokela hape thapo ea puisano ea RS-485 pompong.
12. Bulela sekhechana sa potoloho ea pompo phanele e kholo.
13. Tobetsa pompo; sheba “Ho Tlisa Pompo” leqepheng la 5.

Ho tlosoa ha Kopano ea Drive le ho kenya
Ho qoba kotsi e kotsi kapa e bolaeang ea ts'okelo ea motlakase, TŠOA motlakase ho enjene pele o sebetsa pompong kapa koloing.
Ho qoba kotsi ea motlakase, u se ke ua tlosa tse 'nè tamper proof screws ho tsoa kopanong ea enjene.
Ho tlosa drive le control panel ho tsoa kopanong ea enjene:

1. Etsa bonnete ba hore li-breaker tsohle tsa motlakase le li-switches lia tingoa pele u tlosa phanele ea taolo.
2. Hakolla thapo ea puisano ea RS-485 pompong.
3. Ntsha dikurufu tsa hlooho tse nne (4) tsa Phillips di hukung tse ka ntle tsa letlapa la dikonopo.
4. Tlosa letlapa la likonopo koloing 'me u le behe ka thōko sebakeng se sireletsehileng.
5. Tlosa li-screw tse tharo (3) tsa hlooho tsa Phillips, tse ka hare ho koloi, tse tiisang koloi ho ea ho enjene.
6. Phahamisa kopano ea koloi 'me u e tlose ho adaptara ea enjene e holim'a kopano ea enjene.

Hlokomela: Hlokomela hore u se ke ua tlosa gasket pakeng tsa koloi le enjene, ho bohlokoa ho boloka mongobo ho tsoa koloing le koloing.
Kenya sebaka sa gasket haeba se senyehile. U se ke ua kopanya hape ka gasket e senyehileng kapa e sieo.Ho Tlosa Kopano ea Khanna le ho Kenya, (tsoela pele)
Pele o kenya sehlahisoa sena, bala le ho latela litemoso le litaelo tsohle tse leqepheng la i - ii.
Ho kenya kopano ea koloi ho kopano ea enjene:

1. Etsa bonnete ba hore li-breaker tsohle tsa motlakase le li-switches li tingoe pele u kenya drive.
2. Etsa bonnete ba hore gasket pakeng tsa koloi le koloi e teng. Ho bohlokoa ho boloka mongobo kantle ho drive le motor. Kenya sebaka sa gasket haeba se senyehile. U se ke ua kopanya hape ka gasket e senyehileng kapa e sieo.
3. Netefatsa hore likatiba tse tharo (3) tsa enjene ea lamunu li maemong pele u beha koloi holim'a kopano ea enjene.
4. Lokisetsa kopano ea koloi le adaptara ea enjene 'me u behe koloi ka har'a kopano ea enjine.
5. Sireletsa 'me u tiise kopano ea koloi ka li-screw tse tharo (3) tsa hlooho tsa Phillips.
6. Hokela letlapa la likonopo hape ka har'a drive.
7. Beha letlapa la likonopo sebakeng se lakatsehang koloing 'me u hokelle hape li-screw tse 'ne (4) lihukung tsa drive.
   Hlokomela: Netefatsa hore thapo ya letlapa la dikonopo ha e pinilwe pakeng tsa drive le letlapa la dikonopo.

MOLLO LE CHESA KOTSI - Mochini oa pompo o ka sebetsa ka mocheso o phahameng haholo. Ho fokotsa kotsi ea mollo, u se ke ua lumella makhasi, lithōle, kapa lintho tse tsoang linaheng tse ling ho bokella motlakase oa pompo.
Ho qoba ho chesa ha o tšoara enjene, koala enjene 'me u e lumelle hore e pholile metsotso e 20 pele u sebeletsa. Pompo e fana ka mochine o ikemetseng oa ho thibela motlakase ho sireletsa motlakase ho senya mocheso nakong ea ts'ebetso.

HO BATLE PHOSO

Kamehla hakolla motlakase ho IntelliFlo VSF Variable Speed ​​le Flow Pump ho sekhechana sa potoloho 'me u hakolle thapo ea puisano pele u sebeletsa pompo. Ho hloleha ho etsa joalo ho ka baka lefu kapa kotsi e mpe ho basebeletsi, basebelisi ba letamo kapa ba bang ka lebaka la ho tsukutloa ke motlakase. U SE KE UA leka ho lokisa kapa ho fana ka litšebeletso ntle le ho buisana le morekisi oa hau kapa setsebi se tšoanelehang sa pool. Bala Bukana eohle ea Instolano le Bukana ea Basebelisi pele u leka ho sebelisa, ho fana ka litšebeletso, kapa ho lokisa sesebelisoa sa ho sefa kapa hitara.
Ditemoso le Ditemoso
IntelliFlo® VSF Variable Speed ​​and Flow Pump e bonts'a lialamo tsohle le litemoso holim'a pontšo ea phanele ea taolo.
Ha alamo kapa boemo ba temoso bo le teng, lebone le tsamaellanang le tla bonesoa skrineng.
Ha ho na le alamo: Lebone la alamo " ” e tla bonesa mme dikonopo tsohle tsa phanele ya taolo di tla tingwa ho fihlela alamo e hlakotswe. Ho tobetsa konopo ea Reset ho tla hlakola alamo hang ha boemo ba phoso bo rarollotsoe.
Ketsahalong ea temoso: Leseli la temoso ” ” e tla khantša, empa pompo e tla tsoela pele ho sebetsa. Lebelo, phallo kapa moeli oa khatello o bakang temoso o tlameha ho lokisoa molemong oa ho lokisa temoso.
Hlokomela: Pompo e ke ke ea qala haeba impeller e ntse e potoloha.
Matla / TSOA
Phepelo e kenang voltage e nyane hofeta kamoo ho hlokahalang. Liphoso tsa drive ho itšireletsa ho tloha ho feta hajoale. Koloi e na le li-capacitor tse e bolokang e le matla ka nako e telele ho boloka li-parameter tsa hona joale. Haeba matla a tsosolosoa nakong ea ts'ebetso ena, hoo e ka bang metsotsoana e 20, koloi e ke ke ea qala hape ho fihlela e phethoa.
Ho hloleha ha Priming
Haeba pompo e sa hlalosoe e le ea pele ka har'a "Max Priming Duration" e tla emisa ebe e hlahisa "Priming Alarm" metsotso e 10, ebe u leka ho qala hape. "Max Priming Duration" e behiloe ke mosebelisi ho menu ea priming joalo ka ha ho tšohliloe leqepheng la 19. Haeba pompo e sa khone ho qala nakong ea liteko tse hlano e tla hlahisa alamo e sa feleng e tlamehang ho hlophisoa bocha ka letsoho.
Ho chesa haholo
Haeba mocheso oa koloi o feta 54.4 ° C (130 ° F) pompo e tla fokotsa lebelo butle ho fihlela boemo ba mocheso o feteletseng bo kokobela.
Mokhoa oa Thermal
Ha e sebetsa, enjene e tla matha ka RPM e seng e setiloe ho fihlela mocheso o ka hare oa koloi o eketseha ka holimo ho bonyane. Tšireletso ea ka hare ea pompo ea mocheso e koetsoe ha e hokahane le mochine o ikemetseng.
Tšireletso ea mocheso e fanoa ka ho khetha YES karolong ea ON WITH FREEZE ea menu ea tšebetso ea potoloho ho IntelliTouch® Control System. Ho nolofalletsa ts'ireletso ea ka hare ea mocheso hape, matla a koloi a tlameha ho tima ka baesekele ebe o khutlela morao. BOHLOKOA: Sheba tlhaloso ea Mokhoa oa Mocheso leqepheng la 20.
Ho feta hajoale
Ho bontšitsoe hore koloi e tletse kapa koloi e na le bothata ba motlakase. Koloi e tla qala hape metsotsoana e 20 kamora hore boemo ba hajoale bo hlake.
Ho feta Moqtage
E bonts'a phepelo e fetelletseng voltagMohloli oa metsi o kantle o baka pompo le enjene ho potoloha ka tsela eo e hlahisa vol e fetelletsengtage ho li khanna libese tsa DC tsa kahare. Koloi e tla qala bocha metsotsoana e 20 kamora vol voltagboemo boa hlaka.
Phoso ea ka hare
E bontša hore software e ikemetseng ea ho laola koloi e kopane le phoso. Hlakola alamo ebe u qala pompo hape. Haeba alamo ena e phehella, ikopanye le Pentair Technical Service ho 1-800-831-7133.
Lebelo la Lebelo (Tlhokomeliso)
Pompo e hlokometse hore e kopane le lebelo le phahameng le lumelletsoeng le behiloeng ho menu ea Min/Max. Pompo e tla tsoela pele ho sebetsa, empa e ke ke ea finyella lebelo le lakatsehang.
Khatello ea Khatello (Tlhokomeliso)
Pompo e hlokometse hore e kopane le khatello e phahameng ea tsamaiso e behiloeng ho menu ea Min / Max. Pompo e tla tsoela pele ho sebetsa, empa ha e finyelle lebelo la phallo e lakatsehang kapa lebelo ka lebaka la moeli oa khatello. Karolo e nolofalloa ka ho sa feleng ha e ntse e tsamaisa lenaneo ka lebelo le sa khaotseng la phallo, empa e tlameha ho etsoa ka letsoho haeba mosebelisi a batla hore koloi e shebe khatello e phahameng ha a ntse a tsamaisa lenaneo la lebelo le sa feleng.
Moeli oa Phallo (Tlhokomeliso)
Pompo e hlokometse hore e fihletse tekanyo e phahameng ea phallo e behiloeng ho menu ea Min / Max. Pompo e tla tsoela pele ho sebetsa, empa ha e finyelle lebelo le lakatsehang hobane e sebetsa ka lebelo le phahameng la phallo. The Maximum Flow e ka behoa ho Max/Min menu. Karolo ena e tlameha ho lumelloa ho menu ea Min/Max hore e sebetse ha o ntse o tsamaisa lenaneo la lebelo.
Chate ea ho rarolla mathata

Bothata	Ho ka etsahala Lebaka	Lokisa Ketso
Pompo ho hloleha. (Bakeng sa melaetsa ea tlhokomeliso, sheba Litemoso le Litemoso leqepheng la 25).	Pompo e ke ke ea qala - Ho lutla ha moea ka ho monya. PRIME ERROR e kanna ea hlaha. Pompo e ke ke ea qala - Ha ho na metsi a lekaneng. Pompo ha e tsoe ka mokhoa oa ho qala. Pompo e phethela mokhoa oa ho qala pele haholo, mme/kapa ho ntse ho na le moea o mongata ka tlung Seroto sa pompo se koalehile. Pump strainer gasket e na le phoso.	Sheba liphaephe tsa liphaephe le li-valve holim'a li-valve life kapa life tsa heke tse monyang. Sekoahelo se sireletsehileng holim'a pitsa ea pompo 'me u be le bonnete ba hore sekoahelo sa gasket se teng. Sheba boemo ba metsi ho netefatsa hore skimmer ha e hule moea. Etsa bonnete ba hore mehala ea ho hula, pompo, sefa, le pompo ea volute li tletse metsi. Fetola sebaka sa ho qala ho ea boemong bo phahameng (setting ea kamehla ke 5). Fetola sebaka sa priming ho boemo bo tlase (setting ea kamehla ke 5). Hloekisa pitsa ea sesefa. Kenya sebaka sa gasket.
Fokotsoe bokhoni le/ or hlooho. (Bakeng sa melaetsa ea tlhokomeliso, sheba Litemoso le Litemoso leqepheng la 25).	Lipokotho tsa moea kapa tse lutlang moleng o monyang. PRIMING FAILURE e kanna ea hlaha. Impeller e koetsoeng. PRIMING FAILURE e kanna ea hlaha. Pitsa ea pompo e koetsoeng. PRIMING FAILURE e kanna ea hlaha.	Sheba liphaephe tsa liphaephe le li-valve holim'a li-valve life kapa life tsa heke tse monyang. Tima matla a motlakase pompong. Tlosa liboutu (6) tse ts'oereng ntlo (pitsa ea strainer/volute) ho tiisa poleiti. Tlosa enjene le poleiti ea tiiso hole le bolute. Hloekisa litšila ho tloha ho impeller. Haeba maloanlahla a ke ke a tlosoa, etsa mehato e latelang: 1. Tlosa diffuser le o-ring. 2. Tlosa reverse-thread impeller screw le o-ring. 3. Tlosa, hloekisa le ho kenya impeller hape. 4. Kenya hape sekoere-khoele sa reverse-thread le o-ring. Kenya hape iffuser, le o-ring. Kenya hape enjene le poleiti ea tiiso hore e be volute. Kenya hape linate tsa seal plate 'me u volute le ho tiisa ka mokhoa o sireletsehileng. Sefi se hloekileng sa ho monya. Hloekisa pitsa ea sesefa.
E sa lekaneng ho potoloha. (Bakeng sa melaetsa ea tlhokomeliso, sheba ho Litemoso le Temoso leqepheng la 25).	Sefa kapa seroto sa pompo se litšila. Liphaephe tsa ho hula/ho ntša li nyane haholo. Lebelo le behiloe butle haholo bakeng sa potoloho e nepahetseng ea ho sefa.	Sheba baskete ea sefi; haeba e hoketsoe, tima pompo 'me u hloekise baskete. Hlahloba le ho hloekisa letamo filter. Eketsa boholo ba liphaephe. Eketsa nako ea ts'ebetso ea filtration.
Motlakase bothata.(Bakeng sa melaetsa ea tlhokomeliso, sheba ho Litemoso le Temoso leqepheng la 25).	E ka hlaha e le "Low Voltage” alamo. E ka hlaha e le tlhokomeliso ea "Over Heat".	Lekola voltage liteisheneng tsa makoloi le liphanele ha pompo e ntse e sebetsa. Haeba e le tlase, bona litaelo tsa lithapo kapa u buisane le k'hamphani ea motlakase. Sheba lihokelo tse hlephileng. Lekola mola voltage; haeba e ka tlase ho 90% kapa ho feta 110% ea matla a lekantsoengtagke buisana le ramotlakase ea nang le tumello. Eketsa moea oa moea. Fokotsa mocheso oa tikoloho. Tiisa likhokahano life kapa life tse hlephileng tsa lithapo. Enjene e chesa haholo. Tlosa motlakase ho enjine. Hlahloba molumo o nepahetsengtage. Sheba hore na ho na le impeller kapa impeller rubbing e nepahetseng.

Bothata	Ho ka etsahala Lebaka	Lokisa Ketso
Taolo phanele LCD skrineng dipontsho nako le nako kapa maballo ho/ tima.	Khokahano ea wiring ea koloi e hlephileng.	Sheba kamano pakeng tsa drive le keypad. Sheba setšoantšo leqepheng la 3. Khokahano ea wiring drive e lokela ho ba thata.
Mathata a mechine le lerata.	Enjene ea pompo ea sebetsa empa e na le lerata le leholo. Lintho tse tsoang kantle ho naha (lehlohlojane, tšepe, joalo-joalo) ka sehlohlolong sa pompo. Cavitation. Lerata la ho bua, haholo-holo le bonahala ha pompo e qala kapa butle butle.	Haeba lipeipi tsa ho hula le ho ntša metsi li sa tšehetsoe ka ho lekaneng, kopano ea pompo e tla hatelloa. U se ke ua phahamisa pompo sethaleng sa lepolanka! Palama ka mokhoa o sireletsehileng sethaleng sa konkreite bakeng sa ts'ebetso e khutsitseng ka ho fetesisa. Harola pompo, impeller e hloekileng, latela litaelo tsa ts'ebeletso ea pompo bakeng sa ho kopanya hape. Ntlafatsa maemo a ho hula. Eketsa boholo ba phala. Fokotsa palo ea lisebelisoa. Eketsa khatello ea ho tsoa. Lekola mochini o motenya le mochini o tiisitsoeng ka mor'a setempe (E SE tiiso ea mochini oa pompo). Kenya lubrication ho litiiso tsa rabara tsa shaft.
Pompo e etsa eseng araba ho IntelliTouch, EasyTouch, SunTouch, IntelliComm litaelo tsa tsamaiso.	Tlhophiso e fosahetseng ea othomathike. Marang-rang a puisano ha a sebetse.	1. Etsa bonnete ba hore thapo ea puisano e hoketsoe lipheletsong ka bobeli. 2. Hlahloba hore na aterese ea sebaka sa pompo e lumellana le aterese e sebelisitsoeng ho sistimi ea taolo ea IntelliTouch. 3. Hlahloba hore na pompo e filoe lebitso la potoloho tsamaisong ea taolo ea IntelliTouch. 4. Netefatsa hore ponts'o ea pompo e re "BONTŠA NOTACTIVE". Sesebelisoa se sa sebetseng marang-rang se ka thibela ts'ebetso e nepahetseng ea lisebelisoa tse ling tsa marang-rang. Lisebelisoa li lokela ho khaoloa ka tatellano ho fihlela marang-rang a qala ho sebetsa.

PUSELETSO LIKHABANE

Ntho No.	Tlhaloso	Karolo ea # Almond	Black Karolo ea eona
1	Clamp, Cam le Ramp	357199	357150
2	Bona ka Sekoahelo	357151
3	Sekoahelo 0-ring	350013
4	Stainer Basket	70387
5	Volute	350015	ke 357157
6	0-ring 112 bakeng sa Drain plug (Qty2)	192115
7	Drain plug (Qty2)	71131	357161
8	Voute Kit (E kenyelelitse lintlha 1-7)	357243	357244
9	Nut, 1/4-20 Hex. SS (Qty2)	71406
10	Washer, Flat 1/4″ ID x 5/8″ OD (Qty2)	72183
11	Screw, 1/4-20 x 1″ Hex Cap SS (Qty2)	71657
12	Leoto	70927	357159
13	Ho kenya Maoto, Tšehetso ea Motlakase oa Pompo	70929	357160
14	Bolt, Hex Head 3/8-16 x 7/8° (Qty4)	70429
15	Bolt, Hex Head 3/8-16 x 1-1/4° (Qty4)	70430
16	Washer, Flat 3/8″ ID x 7/8″ OD (Qty6)	72184
17	Bolt, Hex Head 3/8-16 x 2° (Qty2)	70431
18	Enjene, 3.2kW 10 Pole	350305S	350306S
19	Drive, Variable Speed ​​(Mfg. pele ho 11/20)	356880Z	356894Z
	Drive, Variable Speed ​​(Mfg. pele ho 11/20)	356944Z	356992Z
20	Drive Cover Kit (E kenyelelitse Ntho ea #21)	357527Z	358527Z
21	Sekoahelo sa Keypad	400100	401100
22	Keypad Relocation Kit (E kenyeletsa Keypad Cable ea Phalliso le Sekoaelo sa Drive se se nang letho)	356904Z	356905Z

Ntho No.	Tlhaloso	Karolo ea # Almond	Karolo e Ntšo #
23	Drive Hardware Kit (e kenyelletsa Drive Screw, Drive Gasket le Screw Caps)	355685
24	Tiiso Plate	74564	ke 357158
25	Seal Plate Gasket	357100
26	Mochini Tiiso	071734S
	Setiiso sa Mechini, Ozone/Letsoai le Hanela	071732S
27	Impeller (Mfg. pele ho 11/20)	73131
	Impeller (Mfg. kamora 11/20)	356237
28	Washer ea Rubber, Impeller Set Screw	75713
29	Impeller Set Screw, 1/4-20 LH Thread	71652
30	Diffuser (Mfg. pele ho 11/20)	72928
	Diffuser (Mfg. kamora 11/20)	356238
31	Diffuser Set Screw, 4-40 x 1-1/8″ (Qty2)	71660
32	Diffuser 0-ring	355227
33	Nate, 3/8-16 Brass, Nickel Plated (Qty2)	71403
34	Khanna Kopano (Mfg. pele ho 11/20) (E kenyelletsa lintlha 19-21 & 23)	356922Z	355868Z
	Khanna Kopano (Mfg. kamora 11/20) (E kenyelletsa lintlha 19-21 & 23)	356971Z	356991Z
–	50 Ft. Mohala oa puisano	350122
–	Setiiso Plate Kit w/ Mechanical Tiiso (E kenyelelitse lintlha 24-26)	350202	350203
.	Union Kit (E na le 2 Complete Unions bakeng sa pompo e le 'ngoe - Ha e kenyelelitsoe w/ Pump)	357603	N/A
–	Seal Plate Kit, Ozone/Letsoai le hanyetsanang	350199	350198

(-) Ha e Bonngoe

LIEKETSENG MOTS'OANE

Litekanyo tsa PompoLitlhaloso tsa Motlakase
Ts'ireletso ea Potoloho: Palo tse peli 20 AMP sesebelisoa ho Panel ea Motlakase.
Kenyelletso: 230 VAC, 50/60 Hz, 3200 Watts Maximum, 1 phase WEF 6.9 THP 3.95
Li-curve tsa Ts'ebetso ea PumpPanel ea Taolo ea Opereishene: Pump Menu Quick Reference GuidePanel ea Taolo ea Opereishene: Pump Menu Quick Reference Guide (tsoela pele)Lits'oants'o tsohle tse bonts'itsoeng tsa Pentair le li-logo ke thepa ea Pentair. Matshwao a kgwebo a ngodisitsweng le a sa ngodiswang le batho ba bang ke thepa ya beng ba ona. Hobane re ntse re tsoela pele ho ntlafatsa lihlahisoa le lits'ebeletso tsa rona, Pentair e na le tokelo ea ho fetola litlhaloso ntle le tsebiso esale pele.

1620 HAWKINS AVE., SANFORD, NC 27330 • 919-566-8000
10951 WEST LOS ANGELES AVE., MOORPARK, CA 93021 • 805-553-5000
WWW.PENTAIR.COM
© 2020 Penair. Litokelo tsohle li sirelelitsoe. Tokomane ena e ka fetoha ntle le tsebiso.

Litokomane / Lisebelisoa

PENTAIR IntelliFlo VSF Lebelo le Fetohang le Phallo ea Letamo la Phallo [pdf] Tlhophiso Tataiso IntelliFlo VSF Lebelo le Lebelo le Phallang Pool Pump, IntelliFlo VSF, Lebelo le Fetohang le Phallo ea Letamo la Letamo, Lebelo le Phallo ea Letamo la Letamo, Letamo la Phallo, Letamo la Letamo, Pompo

Litšupiso

• Bukana ea Mosebelisi