MOEKETSI
TS'OANE
Tataiso ea ho Kena
Case controller
Mofuta oa EKC 223

Boitsebiso

Kopo

Litekanyo

Ho phahamisa

Litšoantšo tsa lithapo

Kopo	Litšoantšo tsa lithapo
1
2
3
4

Hlokomela: Li-connectors tsa matla: boholo ba terata = 0.5 - 1.5 mm 2, max. torque e tiisang = 0.4 Nm Low voltagli-connectors tsa e: boholo ba terata = 0.15 - 1.5 mm 2, max. torque e tiisang = 0.2 Nm 2L le 3L e tlameha ho kopanngoa le mohato o le mong.

Puisano ya data

Ho kenya	Wiring
Mookameli oa EKC 22x a ka kopanngoa le marang-rang a Modbus ka adapter ea RS-485 (EKA 206) a sebelisa mohala oa sebopeho (080N0327). Bakeng sa lintlha tsa ho kenya ka kopo sheba tataiso ea ho instola bakeng sa adaptara ea EKA 206 - RS485.

Lintlha tsa tekheniki

Likaroloana	Tlhaloso
Sepheo sa taolo	Taolo e sebetsang ea ho utloa mocheso e loketseng ho kenyelletsoa ho li-air-conditioning le lisebelisoa tsa sehatsetsi.
Khaho ea taolo	Taolo e kenyelelitsoeng
Phepelo ea motlakase	084B4055 - 115 V AC / 084B4056 - 230 V AC 50/60 Hz, galvanic isolated low voltytage laola phepelo ea motlakase
Matla a lekantsoeng	Ka tlase ho 0.7 W
Lintho tse kenang	Kenyelletso ea kutlo, Kenyo ea Digital, Konopo ea Mananeo Hokahantsoeng ho SELV matla a lekanyelitsoeng <15 W
Mefuta ea sensor e lumelletsoeng	NTC 5000 Ohm ho 25 °C, (Boleng ba Beta = 3980 ho 25/100 °C - EKS 211) NTC 10000 Ohm ho 25 °C, (Boleng ba Beta = 3435 ho 25/85 °C - EKS 221) PTC 990 Ohm ho 25 °C, (EKS 111) Pt1000, (AKS 11, AKS 12, AKS 21)
Ho nepahala	Lebala la ho lekanya: -40 - 105 °C (-40 - 221 °F)
	Ho nepahala ha molaoli: ±1 K ka tlase ho -35 °C, ±0.5 K pakeng tsa -35 - 25 °C, ±1 K ka holimo ho 25 °C
Mofuta wa ketso	1B (relay)
Sephetho	DO1 - Phetiso ea 1: 16 A, 16 (16) A, EN 60730-1 10 FLA / 60 LRA ho 230 V, UL60730-1 16 FLA / 72 LRA ho 115 V, UL60730-1
	DO2 - Phetiso ea 2: 8 A, 2 FLA / 12 LRA, UL60730-1 8 A, 2 (2 A), EN60730-1
	DO3 - Phetiso ea 3: 3 A, 2 FLA / 12 LRA, UL60730-1 3 A, 2 (2 A), EN60730-1
	DO4 - Phepelo ea 4: 2 A
Pontšo	Pontšo ea LED, linomoro tse 3, ntlha ea decimal le matšoao a nang le mesebetsi e mengata, sekala sa °C + °F
Maemo a ts'ebetso	-10 - 55 °C (14 - 131 °F), 90% Rh
Maemo a polokelo	-40 - 70 °C (-40 - +158 °F), 90% Rh
Tshireletso	Ka pele: IP65 (Gasket e kopantsoe) Ka morao: IP00
Tikoloho	Tekanyo ea tšilafalo ea II, e sa koaheleng
Ho tlolatagsehlopha	Mofuta oa phepelo oa II - 230 V - (ENEC, UL e amoheloa) III - 115 V phepelo ea mofuta - (UL e amoheloa)
Ho hanyetsa mocheso le mollo	Sehlopha sa D (UL94-V0) Mocheso bakeng sa polelo ea teko ea khatello ea bolo Ho latela Annex G (EN 60730-1)
Sehlopha sa EMC	Sehlopha sa I
Litumello	Tlhokomeliso ea UL (US & Canada) (UL 60730-1) CE (LVD & EMC Directive) EAC (SEPOHO) UKCA UA CMIM ROHS2.0 Tumello ea Hazloc bakeng sa lihatsetsi tse tukang (R290/R600a). R290/R600a likopo tsa ho qetela tse sebelisoang ho latela litlhoko tsa IEC60079-15.

Ts'ebetso ea ho bonts'a

Likonopo tse ka pele ho ponts'o li ka sebetsoa ka ho tobetsa tse khutšoane le tse telele (3s).

A	Pontšo ea boemo: Li-LED li khantša ka mokhoa oa ECO/Bosiu, li pholile, li senya le ho sebetsa ka fan.
B	Letšoao la alamo: Letšoao la alamo lea benya haeba alamo e hlaha.
C	Tobetsa nakoana = Khutlela morao Tobetsa nako e telele = Qala potoloho ea ho hula. Pontšo e tla hlaha "Pod" ho netefatsa ho qala.
D	Tobetsa nakoana = Tsamaea holimo Tobetsa nako e telele = Switch controller ON/OFF (setting r12 Main switch in ON/OFF position)
E	Tobetsa nakoana = Tsamaea tlase Tobetsa nako e telele = Qala potoloho ea defrosting. Pontšo e tla bontša khoutu "-d-" ho netefatsa qalo.
F	Tobetsa nakoana = Fetola ntlha e behiloeng Tobetsa nako e telele = E-ea ho menu ea parameter

Ho lokisa ka feme

Selaoli se ka khutlisetsoa ho litlhophiso tsa feme ka ho sebelisa mokhoa o latelang:

1. Motlakase oa OFF
2. Boloka likonopo tsa "∧" le tlase "∨" li tobetse ha u ntse u hokahanya matla a phepelo hape.tage
3. Ha khoutu ea "Face" e hlaha skrineng, khetha "ee"

Hlokomela: Litlhophiso tsa feme ea OEM e tla ba litlhophiso tsa fektheri ea Danfoss kapa kemiso ea feme e hlalositsoeng ke mosebelisi haeba e entsoe. Mosebelisi a ka boloka maemo a hae joalo ka tlhophiso ea feme ea OEM ka paramente o67.

Hlahisa likhoutu

Hlahisa khoutu	Tlhaloso
-d-	Defrost cycle e ntse e tsoela pele
Pod	Ho se ho qaliloe nako ea ho theola mocheso
Phoso	Thempereichara e ke ke ea hlahisoa ka lebaka la phoso ea sensor
—	E bonts'oa kaholimo ho ponts'o: Theko ea paramethara e fihletse boholo. Moeli
—	E bonts'itsoe botlaaseng ba pontšo: Theko ea parameter e fihlile ho min. Moeli
Notlela	Khiboto e bonts'ang e notletsoe
Null	Khiboto ea ponts'o e notletsoe
PS	Khoutu ea phihlello ea hlokahala ho kenya menu ea parameter
Selepe/Ext	Alamo kapa khoutu ea phoso e benyang ka mocheso o tloaelehileng. bala haholo
TLOA	Taolo ea emisoa ha r12 Main switch e TLOA
On	Taolo e qalisoa ha r12 Main switch e BUTSOE (khoutu e bonts'itsoe ka metsotsoana e 3)
Sefahleho	Selaoli se setiloe bocha maemong a feme

Navigation

Lenaneo la parameter le fihlella ka ho tobetsa konopo ea "SET" metsotsoana e 3. Haeba khoutu ea ts'ireletso ea phihlello "o05" e hlalositsoe, ponts'o e tla kopa khoutu ea phihlello ka ho bonts'a khoutu "PS". Hang ha khoutu ea ho fihlella e fanoe ke mosebedisi, lenane la parameter le tla fihleloa.

Qala hantle

Ka mokhoa o latelang o ka qala taolo kapele haholo:

1. Tobetsa konopo ea "SET" bakeng sa metsotsoana ea 3 'me u fihle ho menu ea parameter (ponts'o e tla bontša "ho").
2. Tobetsa konopo e tlase "∨" ho ea ho "tcfg" menu (ponts'o e tla bontša "tcfg")
3. Tobetsa konopo e nepahetseng/">" ho bula menyetla ea tlhophiso (ponts'o e tla bontša r12)
4. Bula paramente ea "r12 Main switch" 'me u emise taolo ka ho e tima (Tobetsa SET)
5. Bula "o61 application mode" ebe u khetha mokhoa o hlokahalang oa kopo (Tobetsa SET)
6. Bula "o06 Sensor type" ebe u khetha mofuta oa sensor ea mocheso o sebelisitsoeng (n5=NTC 5 K, n10=NTC 10 K, Pct.=PTC, Pt1=Pt1000) - (Tobetsa "SET").
7. Bula "o02 DI1 Configuration" 'me u khethe mosebetsi o amanang le tlhahiso ea digital 1 (Ka kopo, sheba lenane la parameter) - (Tobetsa "SET").
8. Bula "o37 DI2 Configuration" 'me u khethe mosebetsi o amanang le tlhahiso ea digital 2 (Ka kopo, sheba lenane la parameter) - (Tobetsa "SET").
9. Bula paramethara ea "o62 Quick setting" ebe u khetha tlhophiso e lumellanang le ts'ebeliso e sebelisoang (ka kopo sheba tafole e seng e setiloe ka tlase) - (Tobetsa "SET").
10. Bula "o03 Network address" 'me u behe aterese ea Modbus ha ho hlokahala.
11. Khutlela ho parameter "r12 Main switch" 'me u e behe sebakeng sa "ON" ho qala taolo.
12. Tsamaea lethathamong lohle la parameter 'me u fetole litlhophiso tsa fektheri moo ho hlokahalang.

Khetho ea litlhophiso tse potlakileng

Ho beha kapele	1	2	3	4	5	6	7
	Kabinete ea MT Tlhaloso ea tlhaho. Emisa ka nako	Kabinete ea MT El. def. Emisa ka nako	Kabinete ea MT El. def. Emisa mocheso	Kabinete LT El. def. Emisa mocheso	Kamore ea MT El. def. Emisa ka nako	Kamore ea MT El. def. Emisa mocheso	Kamore ea LT El. def. Emisa mocheso
r00 Khaotsoe	4 °C	2 °C	2 °C	-24 °C	6 °C	3 °C	-22 °C
r02 Max Cut-out	6 °C	4 °C	4 °C	-22 °C	8 °C	5 °C	-20 °C
r03 Min Cut-out	2 °C	0 °C	0 °C	-26 °C	4 °C	1 °C	-24 °C
A13 Moea o Phahameng	10 °C	8 °C	8 °C	-15 °C	10 °C	8 °C	-15 °C
Al 4 Moea o Mobe	-5 °C	-5 °C	-5 °C	-30 °C	0 °C	0 °C	-30 °C
d01 Def. Mokhoa	Tlhaho	Motlakase	Motlakase	Motlakase	Motlakase	Motlakase	Motlakase
d03 Def.lnterval	6 hora	6 hora	6 hora	12 hora	8 hora	8 hora	12 hora
d10 DefStopSens.	Nako	Nako	Sensor ea S5	55 Sensor	Nako	Sensor ea S5	Sensor ea S5
o02 DI1 Config.					Monyako fct.	Monyako fct.	Monyako fct.

Senotlolo sa lenaneo

Molaoli oa mananeo a nang le Mass Programming Key (EKA 201)

1. Matlafatsa molaoli. Etsa bonnete ba hore balaoli ba hokahane le li-main.
2. Hokela EKA 201 ho molaoli o sebelisa thapo e fapaneng ea sebopeho sa taolo.
3. EKA 201 e tla qala ts'ebetso ea lenaneo ka bo eona.

Lethathamo la paramethara

Khoutu	Bukana ya mongolo o mokgutshwane	Min.	Max.	2	Yuniti	R/W	EKC 224 Appl.
							1	2	3	4
CFg	Tlhophiso
r12	Phetoho e kholo (-1=tšebeletso /0=OFF / 1=0N)	-1	1	0		R/W	*	*	*	*
o61¹)	Khetho ea mokhoa oa kopo (1) API: Cmp/Def/Fan/Light (2)AP2: Cmp/Def/Fan/Alarm (3)AP3: Cmp/ Al/F an/Leseli (4)AP4: Mocheso/Alarm/Leseli	1	4			R/W	*	*	*	*
o06¹)	Khetho ea mofuta oa sensor (0) n5= NTC 5k, (1) n10 = NTC 10k, (2)Pt = Pt1003, (3) Pct. = PTC 1000	0	3	2		R/W	*	*	*	*
o02¹)	Sebopeho sa Dell (0) ea=ha e sebelisoe (1) SD=maemo, (2) tšebetso ea lemati la doo, (3) etsa=alamo ea lemati, (4) SCH=switch e kholo, (5) haufi=mokhoa oa mots'eare/bosiu, (6) rd=ho falla (7) EAL=alamo ea kantle, (8) def.=defrost, (9) Pod = hula I down, (10) Sc=condenser sensor	0	10	0		R/W	*	*	*	*
037¹)	tlhophiso ea DI2 (0) ea=ha e sebelisoe (1) SD=maemo, (2) tšebetso ea lemati la doo, (3) etsa=alamo ea lemati, (4) SCH=switch e kholo, (5) haufi=motsheare/bosiu, (6) sled=refrefense displacement (7) EAL=alamo ya kantle, (8) def.=defrost, (9) Pod= hula fatshe	0	9	0		R/W	*	*	*	*
o62¹)	Tlhophiso e potlakileng ea li-parameter tsa mantlha 0= Ha e sebelisoe 1 = MT, Defrost ea tlhaho, emisa ka nako 2 = MT, El defrost, emisa ka nako 3= MT, El defrost, emisa ka temp. 4 = LT, El defrost stop on temp. 5 = Kamore, MT, El defrost, emisa ka nako 6= Kamore, MT, El defrost, emisa ka temp. 7 = Kamore, LT, El defrost, emisa mocheso.	0	7	0		RIWELA	*	*	*
o03¹)	Aterese ea marang-rang	0	247	0		R/W	*	*	*	*
r-	Thermostat
r00	Sebaka sa mocheso	r03	r02	2.0	°C	R/W	*	*	*	*
r01	Phapang	0.1	20.0	2.0	K	R/W	*	*	*	*
r02	Max. moedi wa setpoint setting	r03	105.0	50.0	°C	R/W	*	*	*	*
r03	Min. moedi wa setpoint setting	–40.0	r02	–35.0	°C	R/W	*	*	*	*
r04	Litokiso tsa mocheso oa ponts'o	–10.0	10.0	0.0	K	R/W	*	*	*	*
r05	Mocheso yuniti rC / °F)	0/C	1/F	0/C		R/W	*	*	*	*
r09	Tokiso ea lets'oao le tsoang ho sensor ea Sair	–20.0	20.0	0.0	°C	R/W	*	*	*	*
r12	Phetoho e kholo (-1=tšebeletso /0=OFF / 1=0N)	-1	1	0		R/W	*	*	*	*
r13	Ho falla ha litšupiso nakong ea ts'ebetso ea bosiu	–50.0	50.0	0.0	K	R/W	*	*		*
r40	Phetoho ea litšupiso tsa Thermostat	–50.0	20.0	0.0	K	R/W	*	*	*	*
r96	Nako ea ho hula	0	960	0	min	R/W	*	*	*
r97	Mocheso oa mocheso oa ho theola fatše	–40.0	105.0	0.0	°C	R/W	*	*	*
A-	Litlhophiso tsa alamo
A03	Ho lieha ha alamo ea mocheso (e khuts'oane)	0	240	30	min	R/W	*	*	*	*
Al2	Ho lieha ha alamo ea mocheso nakong ea ho theoha (nako e telele)	0	240	60	min	R/W	*	*	*	*
A13	Moeli o phahameng oa alamo	–40.0	105.0	8.0	°C	R/W	*	*	*	*
A14	Moeli o tlase oa alamo	–40.0	105.0	–30.0	°C	R/W	*	*	*	*
A27	Alamo e lieha Dll	0	240	30	min	R/W	*	*	*	*
A28	Alamo e lieha DI2	0	240	30	min	R/W	*	*	*	*
A37	Tekanyetso ea alamo bakeng sa alamo ea mocheso oa condenser	0.0	200.0	80.0	°C	R/W	*	*	*
A54	Moeli oa alamo ea condenser block le comp. Ema	0.0	200.0	85.0	°C	R/W	*	*	*
A72	Moqtage tshireletso thusa	0/No	1/Ho joalo	0/No		R/W	*	*	*
A73	Bonyane ba ho khaoha ka matlatage	0	270	0	Volt	R/W	*	*	*
A74	Bonyane ba sehiloeng matlatage	0	270	0	Volt	R/W	*	*	*
A75	Boholo ba sehiloeng ka voltage	0	270	270	Volt	R/W	*	*	*
d-	Kheloha
d01	Mokgwa wa ho qhibidiha (0) eseng =Ha ho letho, (1) eseng = Tlhaho, (2) E1 = Motlakase, (3) khase = Khase e chesang	0	3	2		R/W	*	*	*
d02	Defrost setopong mocheso	0.0	50.0	6.0	°C	R/W	*	*	*
d03	Nako e pakeng tsa defrost e qala	0	240	8	hora	R/W	*	*	*
d04	Max. defrost nako	0	480	30	min	R/W	*	*	*
d05	lime offset bakeng sa ho qala defrost ea pele ha e qala	0	240	0	min	R/W	*	*	*
d06	Nako ea ho phomola	0	60	0	min	R/W	*	*	*
d07	Ho lieha ha fan ho qala ka mor'a ho qhibiliha	0	60	0	min	R/W	*	*	*
d08	Mocheso o qalang oa fene	-40.0	50.0	-5.0	°C	R/W	*	*	*
d09	Ts'ebetso ea fan nakong ea defrost	0/Tlokotsi	1/ Ho qala	1/Ho qala		R/W	*	*	*
d10″	Sensor ea defrost (0=nako, 1=Sair, 2=55)	0	2	0		R/W	*	*	*
d18	Max. comp. nako ea ho sebetsa pakeng tsa defrosts tse peli	0	96	0	hora	R/W	*	*	*
d19	Defrost ha e batloa - lithempereichara tse 55 li lumelletse ho fetoha ha serame. Semeleng se bohareng khetha 20 K (= tima)	0.0	20.0	20.0	K	R/W	*	*	*
d30	Defrost tieho ka mor'a ho hula (0 = OFF)	0	960	0	min	R/W	*	*	*
F—	Fane
F1	Fane sebakeng sa ho emisa compressor (0) FFC = Latela comp., (1) Foo = ON, (2) FPL = Fan pulsing	0	2	1		R/W	*	*	*
F4	Thempereichara ea ho emisa ho fehla moea (55)	-40.0	50.0	50.0	°C	R/W	*	*	*
F7	Fane pulsing ON cycle	0	180	2	min	R/W		*	*
F8	Fene pulsing OFF potoloho	0	180	2	min	R/W	*	*	*
c-	Sekontiri
c01	Min. Ka nako	0	30	1	min	R/W	*	*	*
c02	Min. NAKO-nako	0	30	2	min	R/W	*	*	*
c04	Compressor OFF tieho monyako o butsoe	0	900	0	mots	R/W	*	*	*
c70	Khetho ea ho tšela lefela	0/No	1/Ho joalo	1/Ho joalo		R/W	*	*	*
o-	Tse fapaneng
o01	Ho lieha ha lihlahisoa qalong	0	600	10	mots	R/W	*	*	*	*
o2″	tlhophiso ea DI1 (0) TLOHA=ha e sebelisoe (1) Sdc=boemo, (2) doo=mosebetsi oa lemati, (3) doA=alamo ea lemati, (4) SCH=switch e kholo (5) nig=motsheare/bosiu, (6) rFd=ho falla, (7) EAL=alamo ya ka ntle, (8) dEF=clefrost, (9) Pud=hulela fatshe, (10) Sc=condenser sensor	0	10	0		R/W	*	*	*	*
o3″	Aterese ea marang-rang	0	247	0		R/W	*	*	*	*
5	Khoutu ea ho kena	0	999	0		R/W	*	*	*	*
006″	Khetho ea mofuta oa sensor (0) n5 = NTC 5k, (1) n10 = NTC 10k, (2)Pt = Pt1000, (3) Ptc = PTC 1000	0	3	2		R/W	*	*	*	*
o15	Qeto ea pontšo (0) 0.1, (1)0.5, (2)1.0	0	2	0		R/W	*	*	*	*
o16	Max. kalaka e emeng ka mora ho qhibidiha	0	360	20	min	R/W	*	*	*
o37 '.	Dl? tlhophiso (0) ea=ha e sebelisoe (1) Mokotla=boemo, (2) doo=mosebetsi oa lemati, (3) etsa=alamo ea lemati, (4) SCH=switch e kholo, (5) haufi=motsheare/bosiu, (6) rd=ref Terence displacement, (7) EAL=alamo ya kantle, (8) def.=def ran, (9) Pod=ke hulela fatshe	0	9	0		R/W	*	*	*	*
o38	Tlhophiso ea ts'ebetso ea leseli (0) ho=kamehla, (1) Dan=motšehare/bosiu (2) doo=e thehilweng hodima ketso ya monyako, (3) matlooa = Marang-rang	0	3	1		R/W	*		*	*
o39	Taolo ea leseli ka marang-rang (ha feela o38=3(.NET))	0/Tlokotsi	1/ Ho qala	1/Ho qala		R/W	*		*	*
061″	Khetho ea mokhoa oa kopo (1) API: Cmp/Def/Fan/Light (2) AP2: Cmp/Def/Fan/A 6 rim (3) AP3: Cmp/Al/Fan/Leseli (4) AP4: Mocheso/Alamo/Leseli	1	4	1		R/W	*	*	*	*
o62 tsa	Tlhophiso e potlakileng ea li-parameter tsa mantlha 0= Ha e sebelisoe 1= MT, Defrost ea tlhaho, emisa ka nako 2 = MT, El defrost, emisa ka nako 3= MT, El defrost, emisa ka temp. 4= LT, El defrost stop on temp 5 = Kamore, MT, El defrost, emisa ka nako 6= Kamore, MT, El defrost, emisa ka temp. 7 = Kamore, LT, El defrost, emisa mocheso.	0	7	0		R/W	*	*	*
67	Fetola li-setting tsa feme ea balaoli ka li-setting tsa hona joale	0/No	1/Ho joalo	0/No		R/W	*	*	*	*
91	Hlahisa ka defrost (0) Moea=Mocheso oa Sari / (1) Mocheso=mohatsela o batang/ (2) -drvds e bonts'itsoe	0	2	2		R/W	*	*	*
P—	Polarity
P75	Molaetsa oa alamo o kentsoeng (1) = Ketso ea ho khelosa	0	1	0		R/W	*	*	*
P76	Senotlolo sa keyboard se bulela	0/No	1/Ho joalo	0/No		R/W	*	*	*	*
u-	Tshebeletso
u00	Boemo ba ho laola 50: Tloaelehileng, 51: Wart ka mor'a ho senya. 52: Min ON timer, 53: Min OFF timer, 54: Drip hangata 510: r12 Main switch set TIMA, 511: Thermostat cut-out 514: Defrosting, $15: Fen tieho, 517: Lemati le bulehile, 520: Emergency cooling,525 : Taolo ea letsoho, 530: Potoloho ea ho hula, 532: Ho lieha ho matlafatsa, S33: Ho futhumatsa	0	33	0		R	*	*	*	*
u01	Mocheso oa moea oa Sari	-100.0	200.0	0.0	°C	R	*	*	*	*
u09	Mocheso oa mouoane oa S5	-100.0	200.0	0.0	°C	R	*	*	*	*
u10	Boemo ba ho kenya DI1	0/Tlokotsi	1/ Ho qala	0/Tlokotsi		R	*	*	*	*
u13	Boemo ba bosiu	0/Tlokotsi	1/ Ho qala	0/Tlokotsi		R	*	*	*	*
u37	Boemo ba ho kenya DI2	0/Tlokotsi	1/ Ho qala	0/Tlokotsi		R	*	*	*	*
u28	Referense ea 'nete ea thermostat	-100.0	200.0	0.0		R	*	*	*	*
u58	Compressor/ Valofo ya mothapo wa metsi wa solenoid	0/Tlokotsi	1/ Ho qala	0/Tlokotsi		R	*	*	*
u59	Phetiso ea fan	0/Tlokotsi	1/ Ho qala	0/Tlokotsi		R	*	*	*
u60	Defrost relay	0/Tlokotsi	1/ Ho qala	0/Tlokotsi		R	*	*
u62	Molaetsa oa alamo	0/Tlokotsi	1/ Ho qala	0/Tlokotsi		R		*	*	*
u63	Relay e khanyang	0/Tlokotsi	1/ Ho qala	0/Tlokotsi		R	*		*	*
LSO	Phetolelo ea mofuta oa firmware					R	*	*	*	*
u82	Nomoro ea molaoli.					R	*	*	*	*
u84	Relay ea mocheso	0/Tlokotsi	1/ Ho qala	0/Tlokotsi		R				*
U09	Sc Condenser mocheso	-100.0	200.0	0.0		R	*	*	*

1) Parameter e ka fetoloa feela ha parameter r12 Main switch e le OFF.

Likhoutu tsa alamo

Boemong ba alamo ponts'o e tla fetoha lipakeng tsa ho bala mocheso oa 'nete oa moea le ho bala li-alamo tsa li-alarm tse sebetsang.

Khoutu	Dialamo	Tlhaloso	Alamo ea marang-rang
E29	Phoso ea sensor ea Sari	Sensor ea mocheso oa moea e na le bothata kapa khokahanyo ea motlakase e lahlehile	- Phoso ea Sari
E27	Phoso ea sensor ea Def	Sensor ea S5 Evaporator e na le phoso kapa khokahanyo ea motlakase e lahlehile	- Phoso ea S5
E30	Phoso ea kutlo ea SC	Sensor sa Sac Condenser e na le bothata kapa khokahanyo ea motlakase e lahlehile	- Phoso ea Sac
A01	Alamo ea mocheso o phahameng	Thempereichara ea moea ka khabiteng e phahame haholo	- Alamo e phahameng
A02	Alamo ea mocheso o tlase	Thempereichara ea moea ka khabiteng e tlase haholo	- Tlase t. Alamo
A99	Alamo e phahameng ea Volt	Phepelo voltage phahameng haholo (ts'ireletso ea compressor)	- Moqtage
AA1	Alamo ea Volt e tlase	Phepelo voltage tlase haholo (ts'ireletso ea compressor)	- Phallo e tlasetage
A61	Alamo ea Condenser	Mocheso oa condenser. holimo haholo - hlahloba phallo ea moea	- Alamo ea Khomo
A80	Cond. alamo e thibelang	Mocheso oa condenser. holimo haholo - Ho hlokahala hore ho behoe alamo bocha ka letsoho	— Cond Blocked
A04	Alamo ea monyako	Monyako o butsoe nako e telele haholo	- Alamo ea monyako
A15	DI Alamo	Alamo ea kantle e tsoang ho DI	- Alamo ea DI
A45	Alamo e emeng	Taolo e emisitsoe ke "r12 Main switch"	— Boemo ba standby

1) Alamo ea li-condenser block e ka tsosolosoa ka ho beha r12 Main switch OFF le ON hape kapa ka ho theola molaoli.

Danfoss A / S
Litharollo tsa Boemo ba Leholimo « danfoss.com « +45 7488 2222

Tlhahisoleseding efe kapa efe, ho kenyeletswa, empa e sa felle feela ho tlhahisoleseding e mabapi le kgetho ya sehlahiswa, tshebediso ya sona kapa tshebediso ya sona, moralo wa sehlahiswa, boima, boholo, bokgoni kapa datha efe kapa efe ya tekheniki e dipukung tsa sehlahiswa, ditlhaloso tsa manane a dikhatiso, dipapatso, jj le hore na di fumaneha ka mongolo. , ka molomo, ka mokhoa oa elektronike, inthaneteng kapa ka mokhoa oa ho jarolla, e tla nkoa e le tsebo, 'me e tlama feela haeba, ho fihlela moo, ho etsoa litšupiso tse hlakileng khotheishene kapa netefatso ea taelo. Danfoss e ke ke ea amohela boikarabello bofe kapa bofe bakeng sa liphoso tse ka bang teng libukeng, libukana, livideo le lintho tse ling.
Danfoss e na le tokelo ea ho fetola lihlahisoa tsa eona ntle le tsebiso. Sena se sebetsa le ho lihlahisoa tse otarang empa li sa tlisoa ha feela liphetoho tse joalo li ka etsoa ntle le liphetoho sebopeho, ho lekana kapa tšebetso ea sehlahisoa.
Matšoao 'ohle a thepa ena ke thepa ea lik'hamphani tsa Danfoss A/S kapa tsa Danfoss. Danfoss le logo ea Danfoss ke matšoao a khoebo a Danfoss A/S. Litokelo tsohle li sirelelitsoe.

AN432635050585en-000201
© Danfoss | Litharollo tsa Tlelaemete | 2023.05

Litokomane / Lisebelisoa

	Danfoss EKC 223 Case Controller [pdf] Tlhophiso Tataiso EKC 223, 084B4053, 084B4054, Case Controller, EKC 223 Case Controller
	Danfoss EKC 223 Case Controller [pdf] Tlhophiso Tataiso EKC 223 Case Controller, EKC 223, Case Controller, Controller

Litšupiso

• Bukana ea Mosebelisi