Arahan Pencatat Data Bluetooth Suhu CC653X yang BOLEH DIKESAN

DATALOGGER INSTRUCTIONS

NOTIS PENTING

You MUST download one of the Mobile Apps below to retrieve data and configure device

---

Bluetooth SAHAJA

---

Download TraceableGO™ App

---

---

Bluetooth + Cloud Data Storage

---

TraceableLIVE® Subscription REQUIRED

---

NOW that one of the apps below have been installed on your mobile device

TraceableGO comes ready to use out of the box.

TraceableGO™ App Free Download PERCUMA Ciri-ciri
	Configure datalogger: Tetapkan Penggera Change Logging Interval Togol antara °C/°F Start/Stop Options Bungkus Memori
	Export, Email and Save PDF to Mobile Device
	UNLIMITED CLOUD DATA STORAGE
	Data download to CSV, or Secured PDF
	Graphical UI to analyze data
	Summary data display: Min/Max, Kinetic Mean, Time in Alarm
	Storage of trip parameters
	21 CFR 11 Compliance

TraceableLIVE® App Muat Turun Percuma $30/bulan Ciri-ciri
	Configure datalogger: Tetapkan Penggera Change Logging Interval Togol antara °C/°F Start/Stop Options Bungkus Memori
	Export, Email and Save PDF to Mobile Device
	UNLIMITED CLOUD DATA STORAGE
	Data download to CSV, or Secured PDF
	Graphical UI to analyze data
	Summary data display: Min/Max, Kinetic Mean, Time in Alarm
	Storage of trip parameters
	21 CFR 11 Compliance

KONFIGURASI PERANTI

NOTA: To configure device either TraceableGO™ or TraceableLIVE® Apps must be downloaded to a mobile device.

ENABLE BLUETOOTH

1. Quick press twice START/STOP to enable Bluetooth, and Bluetooth LCD symbol appears.
2. Device starts to advertise to be found, and to be connected. Device Name shown on TraceableGO™ App discovered list looks like CC653X-xxxx, where “CC653X” indicates model number and “-xxxx” is last 4 digits of device serial number.
3. If no connection has been made for SATU MINIT, Bluetooth will be disabled to save battery life, and Bluetooth LCD symbol disappears, or quick press twice again to disable Bluetooth.

KEPADA VIEW PRE-CONFIGURED SETTINGS

1. Enable Bluetooth on device (see above).

2. Open TraceableGO™ or TraceableLIVE® App on any bluetooth enabled mobile device.
Nota: Mobile device must have Bluetooth enabled to receive signal. To enable Bluetooth on a mobile device see mobile device settings.

3. Use TraceableGO™ or TraceableLIVE® App to connect to device. Once the app is open it will begin searching for devices to connect to.

A list of available Dataloggers will appear.

Nota: TraceableGO Bluetooth Dataloggers are serialized and each logger name will match the sticker located on the side of the unit.

4. Once device is selected select Configure.

5. The following parameters are configured through App: START Mode, STOP Mode, ALARM Enable/Disable, Celsius/Fahrenheit, Memory Mode, Data Logging Interval, Alarm Setting.

6. TraceableGO™ comes pre-programmed. To view current settings, tap on configure once device is selected in App.

7. Device comes pre-configured as shown below:

a. Nama Peranti
b. Nombor Siri Peranti
c. Current Battery Status
d. Current Temperature and/or Humidity Readings

PRE-CONFIGURED DEVICE SETTINGS

1. START Mode: Push Start
2. STOP Mode: Push Button Stop
3. Memory Mode: Wrap when Memory is Full
4. Unit Preferences: °C
5. Alarm Setting Alarm Low:
   TAP ON VALUE TO CHANGE
   ▪ Temperature: 2°C (6535 only)
   ▪ Temperature: 20°C (6537 only)
   ▪ Humidity: 25% RH (6537 only)
6. Alarm Setting High Alarm:
   TAP ON VALUE TO CHANGE
   ▪ Temperature: 8°C (6535 only)
   ▪ Temperature: 30°C (6537 only)
   ▪ Humidity: 75% RH (6537 only)
7. Alarm Enable/Disable: Enabled
8. Data Logging Interval: 5 minutes
9. Date/Time is also set to current to central time (Automatically updates when connected to mobile device).

Tap Configure to change factory settings

1. START Mode
Permulaan Segera: Once device is configured it will begin Datalogging.
Tekan butang: Press START/STOP Button to begin Datalogging.
tertunda: Select number of Hours, Minutes and Seconds when device is to begin Datalogging.

2. STOP Mode
Jangan sekali-kali: Device will never stop Datalogging.
Tekan butang: Tekan MULA/BERHENTI Button to Stop Datalogging.

3. Mod Memori
Wrap When Full: Once memory is full, oldest data points will be overwritten with new data points.
Stop When Full: Device will stop recording when Memory is Full 64K (65,536) data points, 7.5 months on 5-minute logging interval.

4. Unit Preferences
° F: Select Fahrenheit
°C: Select Celsius

5. Alarm Setting Alarm Low: TAP ON VALUE TO CHANGE

• Suhu: Set LOWEST Temperature before an alarm is triggered.
• Humidity (6537 only): Set LOWEST Relative Humidity before an alarm is triggered.

6. Alarm Setting High Alarm: TAP ON VALUE TO CHANGE

• Suhu: Set HIGHEST Temperature before an alarm is triggered.
• Humidity (6537 only): Set HIGHEST Relative Humidity value before an alarm is triggered.

7. Alarm Enable/Disable
Didayakan: Penggera dihidupkan.
Dilumpuhkan: Penggera dimatikan.

8. Data Logging Interval
Slide to desired Logging Interval.

9. Save Configurations: Menyimpan tetapan semasa.
NOTA: Saving a Configuration will delete all data on device.

Once device has been configured, device enters STANDBY Mode.

Date/Time is also set to current to central time (Automatically updates when connected to mobile peranti).

HOW TO DOWNLOAD DATA TO MOBILE DEVICE

NOTA: To download data either TraceableGO™ or TraceableLIVE Apps must be downloaded to a mobile device.

ENABLE BLUETOOTH

1. Quick press twice START/STOP to enable Bluetooth, and Bluetooth LCD symbol appears.
2. Device starts to advertise to be found, and to be connected. Device Name shown on TraceableGO™ App discovered list looks like CC653X-xxxx, where “CC653X” indicates model number and “-xxxx” is last 4 digits of device serial number.
3. If no connection has been made for SATU MINIT, Bluetooth will be disabled to save battery life, and Bluetooth LCD symbol  disappears, or quick press twice again to disable Bluetooth.

TO DOWNLOAD RECORDED DATA

1. Device must be stopped. Enable Bluetooth on device (see above).

2. Open TraceableGO™ or TraceableLIVE® App on any bluetooth enabled mobile device. Nota: Mobile device must have Bluetooth enabled to receive signal. To enable Bluetooth on a mobile device see mobile device settings.

3. Use TraceableGO™ or TraceableLIVE® App to connect to device. Once the app is open it will begin searching for devices to connect to.

A list of available Dataloggers will appear.

Nota: TraceableGO™ Bluetooth Dataloggers are serialized and each logger name will match the sticker located on the side of the unit.

4. Once device is selected select Download Data.

5. App will begin extracting the data from TraceableGO™ Device.

6. Once data download is complete, mobile device will display options how to send PDF file, or CSV file (TraceableLIVE only). Tap Done and download is complete.

SPESIFIKASI

Kucing. No. 6535

Kucing. No. 6538

Kucing. No. 6537

SUHU

6535: Ambient Range: -20.0 hingga 70.0°C (-4.0 hingga 158.0°F)
6536/6538 Probe Range: -50.0 hingga 70.0°C (-58.0 hingga 158.0°F)
6539 Probe Range: -90.00 hingga 100.00°C (-130.00 hingga 212.00°F)
Resolusi: 0.1°C
Ketepatan:
6535: ±0.4°C between -10 and 70°C, otherwise ±0.5°C
6536/6538: ±0.3°C
6539: ±0.2°C

RELATIVE HUMIDITY & TEMPERATURE

Suhu—
Julat Ambien: –20.0 hingga 70.0 ° C (–4.0 hingga 158.0 ° F)
Resolusi: 0.1°C
Ketepatan: ±0.4°C between –10 and 70°C, otherwise ±0.5°C

Relative Humidity—
Julat Ambien: 0% to 95%RH, non-condensing
Resolusi: 0.1% RH
Ketepatan: ±3% RH between 5 to 75%, otherwise ±5% RH

EXTERNAL PROBE

6536 Bullet Probe: Standard plastic probe sensor with cable. Designed for use in air and liquids, the sensor and cable may be completely immersed. Probe size: 3/16” diameter, 4/5” length; 10 foot cable

6538 Bottle Probe: Designed to simulate the temperature of stored liquids, use in transportation coolers, refrigerators and freezers. Bottle probes are filled with a patented nontoxic glycol solution that is GRAS (Generally Recognized As Safe) by the FDA (Food and Drug Administration) eliminating concerns about incidental contact with food or drinking water. The included micro-thin probe cable permits refrigerator/freezer doors to close on it. (Do not immerse bottle probes in liquid). Probe size: 1 x 2-1/2 inches; 10 foot cable.

6539 Stainless-Steel/Platinum Probe: Detachable stainless steel 316 Probe with Platinum Sensor and 9 feet of cable are supplied with the unit. Probe has a diameter of 1/8-inch, stem length of 6-1/4 inches, overall length of 9 inches.

Bateri: 2 AAA Alkaline batteries (3.0V)

Dimensi: L x H x D: 3.5 x 2 x 0.79” (89 x 51 x 20 mm)

Petunjuk Tahap Bateri:

Tahap bateri	LCD symbol
≥ 80% (2.78V)
≥ 60% (2.56V), < 80%
≥ 40% (2.34V), < 60%
≥ 20% (2.12V), < 40%
≥ 10% (2.01V), < 20%
< 10% Flashing

Nota: Battery level is updated every 5 minutes.

Nota: Once battery level drops to below 10%, device may not work properly. Replace batteries immediately.

Nota: When replacing batteries, after removing the old batteries, wait 10 seconds before inserting new batteries. Otherwise, Bluetooth may not work properly.

MEASUREMENT READING UPDATE FREQUENCY

Temperature and Humidity: 5 seconds;

Nota: If a reading is out of operating range, corresponding location on LCD will display ‘–.-‘, and such out of range reading will not trigger alarm.

DATA LOGGING FREQUENCY:

5 min by default, user-adjustable between 1 minute and 12 hours with 1 minute step.

DATA STORAGE CAPACITY

penggera: Most recent 90 Alarm events

Data: 64K (65536) data points, 7.5 months on 5-minute logging interval

DEVICE OPERATING MODES

• IDLE Mode: First time battery inserted, and device has not been configured
• STANDBY Mode: Device has been configured, but not started;
• RUN Mode: Device starts to measure and log data.
• STOP Mode: Device stops from RUN Mode. In STOP Mode, device does not update measurements or log data, and the last measurements are displayed.

VIEW BACAAN SEMASA

1. Temperature ONLY unit: Current reading, minimum/maximum reading, run time/alarm time toggling, Memory mode are shown on LCD.
2. Humidity and Temperature unit: Current temperature/humidity reading toggling every 5 seconds, minimum/maximum reading since last clearing, run time/alarm time, Memory mode are shown on LCD.

VIEW CURRENT MIN/MAX

Temperature ONLY unit: Current temperature Min/Max values are displayed on LCD. Humidity and Temperature unit: Current temperature/humidity Min/Max values are toggled display.

Nota: Every time device is configured, or resumes to run from STOP Mode, Min/Max values are reset.

VIEWING RUN TIME/ALARM TIME

Run Time/Alarm Time is toggled to display on LCD. If Run Time is displayed, LCD symbol JALANKAN MASA appears; if Alarm Time is displayed, LCD symbol MASA PENGGERA muncul.

Nota: Alarm Time is accumulated for both Low Alarm and Hi Alarm for each channel (temperature, humidity).

MEMORI

If Memory Mode is set to WRAP WHEN FULL, appears on LCD; If Memory Mode is set to STOP WHEN FULL, MEM muncul pada LCD.

PENGGERA

1. Once an alarm is triggered by any of temperature, humidity out of set alarm range, LCD symbol LOW ALM dan/atau HI ALM starts to flash. An Alarm Event will be logged.
2. Menekan MULA/BERHENTI once will clear alarm, LCD symbol stops flashing. An Alarm Acknowledge Event will be logged.
3. If temperature, or humidity falls back to normal range, an Alarm Event will be logged. If any of temperature, humidity measurement goes back to out of alarm range, alarm will be triggered again.
4. If device’s START Mode is configured as PUSH BUTTON TO START (default), device LCD displays ‘push to start’. Press and hold MULA/BERHENTI until LCD symbol appears. Device enters RUN Mode. If device’s START Mode is configured as IMMEDIATE START, device enters RUN Mode immediately. If device’s START Mode is configured as DELAYED TIME START, delayed start time set by user is counting down on device LCD. Once the counting time reaches 0, device enters RUN Mode.
5. Jika dalam Mod RUN, LCD symbol LARI appears, and logs data at user-defined interval. If STOP Mode is configured as PUSH BUTTON TO STOP, press and hold MULA/BERHENTI until LCD symbol BERHENTI appears. Device enters STOP Mode. If STOP Mode is configured as NEVER STOP, device will ignore button press, and will stop when memory is full if Memory Mode is set to STOP WHEN FULL, or will stop when TraceableGO™ App is connected to device and downloads the data.
6. If in STOP Mode, press and hold MULA/BERHENTI until LCD symbol LARI appears. Device enters RUN Mode and resumes to log data at current setting. Anytime device resumes to log data from STOP Mode, Min/Max values are reset.

Nota: If device in STOP Mode, START Mode will be set to PUSH BUTTON TO START regardless of previous Start Mode Setting. If Delayed Start Mode is needed while device in STOP Mode, device must be re-configured.

Nota: While device is connected to TraceableGO™ App, once Device has received command from App to upload data to App, device will stop logging data and enter STOP Mode if it is still in RUN mode.

VIEW MEMORY USAGE, CURRENT DATE/TIME, DEVICE’S SERIAL NUMBER

1. Tekan dan lepaskan MULA/BERHENTI butang

2. Memory usage in percentage is shown on LCD. The percentage indicates how much internal data memory storage has been used;

3. Number of days, hours, minutes left till memory is full are also displayed on the second line;

4. Dalam masa 10 saat, tekan MULA/BERHENTI again, current date/time is displayed on device LCD. The following figure shows 9/14/2017, 17:30

5. Dalam masa 10 saat, tekan MULA/BERHENTI again, device S/N will be displayed on LCD.

6. To return to normal working status, press MULA/BERHENTI again, or wait for 10 seconds and device will automatically go back to normal working status.

Nota: If Memory Mode is set to WRAP WHEN FULL: LCD symbol starts to flash on the display when the memory is full. Once memory is full, the oldest data points will be overwritten with new data points.

If Memory Mode is set to STOP WHEN FULL: LCD symbol MEM starts to flash on the display when the memory is 95% full. Once memory is full, the device will stop logging new data points.

CLEAR DATA MEMORY STORAGE

1. Data points stored in device internal storage can only be cleared through App or battery removal.
2. Each time device is configured, all stored data points will be cleared.
3. Run Time/Alarm Time are also reset.

MAKLUMAT PERATURAN

Peralatan ini telah diuji dan didapati mematuhi had untuk peranti digital Kelas B, menurut Bahagian 15 Peraturan FCC. Had ini direka bentuk untuk memberikan perlindungan yang munasabah terhadap gangguan berbahaya dalam pemasangan kediaman. Peralatan ini menjana, menggunakan dan boleh memancarkan tenaga frekuensi radio dan, jika tidak dipasang dan digunakan mengikut arahan, boleh menyebabkan gangguan berbahaya kepada komunikasi radio.

Walau bagaimanapun, tiada jaminan bahawa gangguan tidak akan berlaku dalam pemasangan tertentu. Jika peralatan ini menyebabkan gangguan berbahaya kepada penerimaan radio atau televisyen, yang boleh ditentukan dengan mematikan dan menghidupkan peralatan, pengguna digalakkan untuk cuba membetulkan gangguan dengan satu atau lebih daripada langkah berikut:

• Arahkan semula atau letakkan semula antena penerima.
• Tingkatkan pemisahan antara peralatan dan penerima.
• Sambungkan peralatan ke dalam alur keluar pada litar yang berbeza daripada yang disambungkan kepada penerima.
• Rujuk pengedar atau juruteknik radio/TV yang berpengalaman untuk mendapatkan bantuan.

Peranti ini mematuhi Bahagian 15 Peraturan FCC. Pengendalian tertakluk kepada dua syarat berikut: (1) peranti ini tidak boleh menyebabkan gangguan berbahaya, dan (2) peranti ini mesti menerima sebarang gangguan yang diterima, termasuk gangguan yang boleh menyebabkan operasi yang tidak diingini.

Hereby, Traceable Products, declares that this digital thermometer is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.

Peranti ini mematuhi standard RSS yang dikecualikan lesen Industri Kanada. Pengendalian tertakluk kepada dua syarat berikut: (1) peranti ini tidak boleh menyebabkan gangguan, dan (2) peranti ini mesti menerima sebarang gangguan, termasuk gangguan yang boleh menyebabkan pengendalian peranti yang tidak diingini.

NOTA: PEMBERI PEMBERIAN TIDAK BERTANGGUNGJAWAB ATAS SEBARANG PERUBAHAN ATAU PENGUBAHSUAIAN YANG TIDAK DILULUSKAN DENGAN NYATA OLEH PIHAK YANG BERTANGGUNGJAWAB UNTUK PEMATUHAN. PENGUBAHSUAIAN TERSEBUT BOLEH MENGOBOHKAN WILAYAH PENGGUNA UNTUK MENGENDALIKAN PERALATAN.

WARANTI, PERKHIDMATAN ATAU PENCALIBRASI SEMULA

Untuk jaminan, servis atau penentukuran semula, hubungi:

PRODUK YANG BOLEH DITERUSKAN®
12554 Old Galveston Rd. Suite B230 • Webster, Texas 77598 Amerika Syarikat
Ph. 281 482-1714 • Faks 281 482-9448
e-mel support@traceable.com • www.traceable.com

Traceable® Products are ISO 9001:2015 Quality-Certified by DNV and ISO/IEC 17025:2017 accredited as a Calibration Laboratory by A2LA.

TraceableLIVE® and TraceableGO™ are registered trademark/trademarks of Cole-Parmer.

©2020 Traceable® Products. 92-6535-20  Rev. 3 080725

Dokumen / Sumber

TRACEABLE CC653X Temperature Bluetooth Data Logger [pdf] Arahan CC653X, CC653X Temperature Bluetooth Data Logger, Temperature Bluetooth Data Logger, Bluetooth Data Logger, Data Logger

Rujukan

• Manual Pengguna