TRACEABLE CC653X Temperature Bluetooth Data Logger Təlimatları

DATALOGGER INSTRUCTIONS

Vacib XƏBƏRDARLIQ

You MUST download one of the Mobile Apps below to retrieve data and configure device

---

YALNIZ Bluetooth

---

Download TraceableGO™ App

---

---

Bluetooth + Cloud Data Storage

---

TraceableLIVE® Subscription REQUIRED

---

NOW that one of the apps below have been installed on your mobile device

TraceableGO comes ready to use out of the box.

TraceableGO™ App Free Download PULSUZ Xüsusiyyətlər
	Configure datalogger: Siqnal qurun Change Logging Interval °C/°F arasında dəyişin Start/Stop Options Yaddaş sarğı
	Export, Email and Save PDF to Mobile Device
	UNLIMITED CLOUD DATA STORAGE
	Data download to CSV, or Secured PDF
	Graphical UI to analyze data
	Summary data display: Min/Max, Kinetic Mean, Time in Alarm
	Storage of trip parameters
	21 CFR 11 Compliance

TraceableLIVE® App Pulsuz Yüklə $30/ay Xüsusiyyətlər
	Configure datalogger: Siqnal qurun Change Logging Interval °C/°F arasında dəyişin Start/Stop Options Yaddaş sarğı
	Export, Email and Save PDF to Mobile Device
	UNLIMITED CLOUD DATA STORAGE
	Data download to CSV, or Secured PDF
	Graphical UI to analyze data
	Summary data display: Min/Max, Kinetic Mean, Time in Alarm
	Storage of trip parameters
	21 CFR 11 Compliance

CİHAZI KONFİQRASİYA EDİN

QEYD: To configure device either TraceableGO™ or TraceableLIVE® Apps must be downloaded to a mobile device.

ENABLE BLUETOOTH

1. Quick press twice START/STOP to enable Bluetooth, and Bluetooth LCD symbol appears.
2. Device starts to advertise to be found, and to be connected. Device Name shown on TraceableGO™ App discovered list looks like CC653X-xxxx, where “CC653X” indicates model number and “-xxxx” is last 4 digits of device serial number.
3. If no connection has been made for BİR DƏQİQƏ, Bluetooth will be disabled to save battery life, and Bluetooth LCD symbol disappears, or quick press twice again to disable Bluetooth.

TO VIEW PRE-CONFIGURED SETTINGS

1. Enable Bluetooth on device (see above).

2. Open TraceableGO™ or TraceableLIVE® App on any bluetooth enabled mobile device.
Qeyd: Mobile device must have Bluetooth enabled to receive signal. To enable Bluetooth on a mobile device see mobile device settings.

3. Use TraceableGO™ or TraceableLIVE® App to connect to device. Once the app is open it will begin searching for devices to connect to.

A list of available Dataloggers will appear.

Qeyd: TraceableGO Bluetooth Dataloggers are serialized and each logger name will match the sticker located on the side of the unit.

4. Once device is selected select Configure.

5. The following parameters are configured through App: START Mode, STOP Mode, ALARM Enable/Disable, Celsius/Fahrenheit, Memory Mode, Data Logging Interval, Alarm Setting.

6. TraceableGO™ comes pre-programmed. To view current settings, tap on configure once device is selected in App.

7. Device comes pre-configured as shown below:

a. Cihaz Adı
b. Cihazın Seriya Nömrəsi
c. Current Battery Status
d. Current Temperature and/or Humidity Readings

PRE-CONFIGURED DEVICE SETTINGS

1. START Mode: Push Start
2. STOP Mode: Push Button Stop
3. Memory Mode: Wrap when Memory is Full
4. Unit Preferences: °C
5. Alarm Setting Alarm Low:
   TAP ON VALUE TO CHANGE
   ▪ Temperature: 2°C (6535 only)
   ▪ Temperature: 20°C (6537 only)
   ▪ Humidity: 25% RH (6537 only)
6. Alarm Setting High Alarm:
   TAP ON VALUE TO CHANGE
   ▪ Temperature: 8°C (6535 only)
   ▪ Temperature: 30°C (6537 only)
   ▪ Humidity: 75% RH (6537 only)
7. Alarm Enable/Disable: Enabled
8. Data Logging Interval: 5 minutes
9. Date/Time is also set to current to central time (Automatically updates when connected to mobile device).

Tap Configure to change factory settings

1. START Mode
Dərhal Başlanğıc: Once device is configured it will begin Datalogging.
Düymə düyməsini basın: Press START/STOP Button to begin Datalogging.
Gecikmiş: Select number of Hours, Minutes and Seconds when device is to begin Datalogging.

2. STOP Mode
Heç vaxt: Device will never stop Datalogging.
Düymə düyməsini basın: basın START/STOP Button to Stop Datalogging.

3. Yaddaş rejimi
Wrap When Full: Once memory is full, oldest data points will be overwritten with new data points.
Stop When Full: Device will stop recording when Memory is Full 64K (65,536) data points, 7.5 months on 5-minute logging interval.

4. Unit Preferences
° F: Select Fahrenheit
° C: Select Celsius

5. Alarm Setting Alarm Low: TAP ON VALUE TO CHANGE

• Temperatur: Set LOWEST Temperature before an alarm is triggered.
• Humidity (6537 only): Set LOWEST Relative Humidity before an alarm is triggered.

6. Alarm Setting High Alarm: TAP ON VALUE TO CHANGE

• Temperatur: Set HIGHEST Temperature before an alarm is triggered.
• Humidity (6537 only): Set HIGHEST Relative Humidity value before an alarm is triggered.

7. Alarm Enable/Disable
Aktiv edildi: Siqnal aktivdir.
Əlil: Siqnal söndürülüb.

8. Data Logging Interval
Slide to desired Logging Interval.

9. Save Configurations: Cari parametrləri saxlayır.
QEYD: Saving a Configuration will delete all data on device.

Once device has been configured, device enters STANDBY Mode.

Date/Time is also set to current to central time (Automatically updates when connected to mobile qurğu).

HOW TO DOWNLOAD DATA TO MOBILE DEVICE

QEYD: To download data either TraceableGO™ or TraceableLIVE Apps must be downloaded to a mobile device.

ENABLE BLUETOOTH

1. Quick press twice START/STOP to enable Bluetooth, and Bluetooth LCD symbol appears.
2. Device starts to advertise to be found, and to be connected. Device Name shown on TraceableGO™ App discovered list looks like CC653X-xxxx, where “CC653X” indicates model number and “-xxxx” is last 4 digits of device serial number.
3. If no connection has been made for BİR DƏQİQƏ, Bluetooth will be disabled to save battery life, and Bluetooth LCD symbol  disappears, or quick press twice again to disable Bluetooth.

TO DOWNLOAD RECORDED DATA

1. Device must be stopped. Enable Bluetooth on device (see above).

2. Open TraceableGO™ or TraceableLIVE® App on any bluetooth enabled mobile device. Qeyd: Mobile device must have Bluetooth enabled to receive signal. To enable Bluetooth on a mobile device see mobile device settings.

3. Use TraceableGO™ or TraceableLIVE® App to connect to device. Once the app is open it will begin searching for devices to connect to.

A list of available Dataloggers will appear.

Qeyd: TraceableGO™ Bluetooth Dataloggers are serialized and each logger name will match the sticker located on the side of the unit.

4. Once device is selected select Download Data.

5. App will begin extracting the data from TraceableGO™ Device.

6. Once data download is complete, mobile device will display options how to send PDF file, or CSV file (TraceableLIVE only). Tap Done and download is complete.

XÜSUSİYYƏTLƏR

Pişik. № 6535

Pişik. № 6538

Pişik. № 6537

TEMPERATURA

6535: Ambient Range: -20.0 ilə 70.0°C (-4.0 ilə 158.0°F) arasında
6536/6538 Probe Range: -50.0 ilə 70.0°C (-58.0 ilə 158.0°F) arasında
6539 Probe Range: -90.00 ilə 100.00°C (-130.00 ilə 212.00°F) arasında
Qətnamə: 0.1°C
Dəqiqlik:
6535: ±0.4°C between -10 and 70°C, otherwise ±0.5°C
6536/6538: ±0.3°C
6539: ±0.2°C

RELATIVE HUMIDITY & TEMPERATURE

Temperatur -
Ətraf Aralığı: –20.0 - 70.0 ° C (–4.0 - 158.0 ° F)
Qətnamə: 0.1°C
Dəqiqlik: ±0.4°C between –10 and 70°C, otherwise ±0.5°C

Relative Humidity—
Ətraf Aralığı: 0% to 95%RH, non-condensing
Qətnamə: 0.1% RH
Dəqiqlik: ±3% RH between 5 to 75%, otherwise ±5% RH

EXTERNAL PROBE

6536 Bullet Probe: Standard plastic probe sensor with cable. Designed for use in air and liquids, the sensor and cable may be completely immersed. Probe size: 3/16” diameter, 4/5” length; 10 foot cable

6538 Bottle Probe: Designed to simulate the temperature of stored liquids, use in transportation coolers, refrigerators and freezers. Bottle probes are filled with a patented nontoxic glycol solution that is GRAS (Generally Recognized As Safe) by the FDA (Food and Drug Administration) eliminating concerns about incidental contact with food or drinking water. The included micro-thin probe cable permits refrigerator/freezer doors to close on it. (Do not immerse bottle probes in liquid). Probe size: 1 x 2-1/2 inches; 10 foot cable.

6539 Stainless-Steel/Platinum Probe: Detachable stainless steel 316 Probe with Platinum Sensor and 9 feet of cable are supplied with the unit. Probe has a diameter of 1/8-inch, stem length of 6-1/4 inches, overall length of 9 inches.

Batareya: 2 AAA Alkaline batteries (3.0V)

Ölçü: L x H x D: 3.5 x 2 x 0.79” (89 x 51 x 20 mm)

Batareya səviyyəsinin göstəricisi:

Batareya səviyyəsi	LCD symbol
≥ 80% (2.78V)
≥ 60% (2.56V), < 80%
≥ 40% (2.34V), < 60%
≥ 20% (2.12V), < 40%
≥ 10% (2.01V), < 20%
< 10% Flashing

Qeyd: Battery level is updated every 5 minutes.

Qeyd: Once battery level drops to below 10%, device may not work properly. Replace batteries immediately.

Qeyd: When replacing batteries, after removing the old batteries, wait 10 seconds before inserting new batteries. Otherwise, Bluetooth may not work properly.

MEASUREMENT READING UPDATE FREQUENCY

Temperature and Humidity: 5 seconds;

Qeyd: If a reading is out of operating range, corresponding location on LCD will display ‘–.-‘, and such out of range reading will not trigger alarm.

DATA LOGGING FREQUENCY:

5 min by default, user-adjustable between 1 minute and 12 hours with 1 minute step.

DATA STORAGE CAPACITY

Siqnal: Most recent 90 Alarm events

Məlumat: 64K (65536) data points, 7.5 months on 5-minute logging interval

DEVICE OPERATING MODES

• IDLE Mode: First time battery inserted, and device has not been configured
• STANDBY Mode: Device has been configured, but not started;
• RUN Mode: Device starts to measure and log data.
• STOP Mode: Device stops from RUN Mode. In STOP Mode, device does not update measurements or log data, and the last measurements are displayed.

VIEW CARİ OXUMA

1. Temperature ONLY unit: Current reading, minimum/maximum reading, run time/alarm time toggling, Memory mode are shown on LCD.
2. Humidity and Temperature unit: Current temperature/humidity reading toggling every 5 seconds, minimum/maximum reading since last clearing, run time/alarm time, Memory mode are shown on LCD.

VIEW CURRENT MIN/MAX

Temperature ONLY unit: Current temperature Min/Max values are displayed on LCD. Humidity and Temperature unit: Current temperature/humidity Min/Max values are toggled display.

Qeyd: Every time device is configured, or resumes to run from STOP Mode, Min/Max values are reset.

VIEWING RUN TIME/ALARM TIME

Run Time/Alarm Time is toggled to display on LCD. If Run Time is displayed, LCD symbol ZAMAN İŞLƏYİN appears; if Alarm Time is displayed, LCD symbol ALARM VAXTI görünür.

Qeyd: Alarm Time is accumulated for both Low Alarm and Hi Alarm for each channel (temperature, humidity).

YADDAŞ

If Memory Mode is set to WRAP WHEN FULL, appears on LCD; If Memory Mode is set to STOP WHEN FULL, MEM LCD-də görünür.

ALARM

1. Once an alarm is triggered by any of temperature, humidity out of set alarm range, LCD symbol LOW ALM və/və ya HI ALM starts to flash. An Alarm Event will be logged.
2. basaraq START/STOP once will clear alarm, LCD symbol stops flashing. An Alarm Acknowledge Event will be logged.
3. If temperature, or humidity falls back to normal range, an Alarm Event will be logged. If any of temperature, humidity measurement goes back to out of alarm range, alarm will be triggered again.
4. If device’s START Mode is configured as PUSH BUTTON TO START (default), device LCD displays ‘push to start’. Press and hold START/STOP until LCD symbol appears. Device enters RUN Mode. If device’s START Mode is configured as IMMEDIATE START, device enters RUN Mode immediately. If device’s START Mode is configured as DELAYED TIME START, delayed start time set by user is counting down on device LCD. Once the counting time reaches 0, device enters RUN Mode.
5. Əgər daxil RUN rejimi, LCD symbol KAÇ appears, and logs data at user-defined interval. If STOP Mode is configured as PUSH BUTTON TO STOP, press and hold START/STOP until LCD symbol STOP appears. Device enters STOP Mode. If STOP Mode is configured as NEVER STOP, device will ignore button press, and will stop when memory is full if Memory Mode is set to STOP WHEN FULL, or will stop when TraceableGO™ App is connected to device and downloads the data.
6. If in STOP Mode, press and hold START/STOP until LCD symbol KAÇ appears. Device enters RUN Mode and resumes to log data at current setting. Anytime device resumes to log data from STOP Mode, Min/Max values are reset.

Qeyd: If device in STOP Mode, START Mode will be set to PUSH BUTTON TO START regardless of previous Start Mode Setting. If Delayed Start Mode is needed while device in STOP Mode, device must be re-configured.

Qeyd: While device is connected to TraceableGO™ App, once Device has received command from App to upload data to App, device will stop logging data and enter STOP Mode if it is still in RUN mode.

VIEW MEMORY USAGE, CURRENT DATE/TIME, DEVICE’S SERIAL NUMBER

1. Basın və buraxın START/STOP düyməsi

2. Memory usage in percentage is shown on LCD. The percentage indicates how much internal data memory storage has been used;

3. Number of days, hours, minutes left till memory is full are also displayed on the second line;

4. 10 saniyə ərzində basın START/STOP again, current date/time is displayed on device LCD. The following figure shows 9/14/2017, 17:30

5. 10 saniyə ərzində basın START/STOP again, device S/N will be displayed on LCD.

6. To return to normal working status, press START/STOP again, or wait for 10 seconds and device will automatically go back to normal working status.

Qeyd: If Memory Mode is set to WRAP WHEN FULL: LCD symbol starts to flash on the display when the memory is full. Once memory is full, the oldest data points will be overwritten with new data points.

If Memory Mode is set to STOP WHEN FULL: LCD symbol MEM starts to flash on the display when the memory is 95% full. Once memory is full, the device will stop logging new data points.

CLEAR DATA MEMORY STORAGE

1. Data points stored in device internal storage can only be cleared through App or battery removal.
2. Each time device is configured, all stored data points will be cleared.
3. Run Time/Alarm Time are also reset.

tənzimləyici məlumat

Bu avadanlıq sınaqdan keçirilmiş və FCC Qaydalarının 15-ci hissəsinə uyğun olaraq B sinfi rəqəmsal cihaz üçün məhdudiyyətlərə uyğun olduğu müəyyən edilmişdir. Bu məhdudiyyətlər yaşayış qurğusunda zərərli müdaxilədən ağlabatan müdafiəni təmin etmək üçün nəzərdə tutulub. Bu avadanlıq radiotezlik enerjisi yaradır, istifadə edir və yaya bilər və təlimatlara uyğun quraşdırılıb istifadə edilmədikdə, radio rabitəsinə zərərli müdaxilə yarada bilər.

Bununla belə, müəyyən bir quraşdırmada müdaxilənin baş verməyəcəyinə dair heç bir zəmanət yoxdur. Əgər bu avadanlıq radio və ya televiziya qəbuluna zərərli müdaxiləyə səbəb olarsa və bu, avadanlığın söndürülməsi və açılması ilə müəyyən edilə bilər, istifadəçiyə aşağıdakı tədbirlərdən biri və ya bir neçəsi ilə müdaxiləni düzəltməyə çalışması tövsiyə olunur:

• Qəbul edən antenanın istiqamətini dəyişdirin və ya yerini dəyişdirin.
• Avadanlıq və qəbuledici arasındakı məsafəni artırın.
• Avadanlığı qəbuledicinin qoşulduğu dövrədən fərqli bir dövrədə rozetkaya qoşun.
• Yardım üçün dilerlə və ya təcrübəli radio/televiziya texniki ilə məsləhətləşin.

Bu cihaz FCC Qaydalarının 15-ci hissəsinə uyğundur. Əməliyyat aşağıdakı iki şərtə tabedir: (1) bu cihaz zərərli müdaxiləyə səbəb olmaya bilər və (2) bu cihaz istənilən müdaxiləni, o cümlədən arzuolunmaz işə səbəb ola biləcək müdaxiləni qəbul etməlidir.

Hereby, Traceable Products, declares that this digital thermometer is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.

Bu cihaz Industry Canada lisenziyasız RSS standart(lar)ına uyğundur. Əməliyyat aşağıdakı iki şərtə tabedir: (1) bu cihaz müdaxiləyə səbəb olmaya bilər və (2) bu cihaz istənilən müdaxiləni, o cümlədən cihazın arzuolunmaz işinə səbəb ola biləcək müdaxiləni qəbul etməlidir.

QEYD: QRANT TƏRƏFİ UYĞUNA MƏSULİYYƏT OLAN TƏRƏF TARAFINDAN AÇIQ TƏSDİQ EDİLMƏYƏN DƏYİŞİKLİKLƏR VƏ YA DƏYİŞİKLƏRƏ GÖRƏ MƏSULİYYƏT DEYİL. BELƏ DƏYİŞİKLİKLƏR İSTİFADƏÇİNİN AVADANLIQI İSTİFADƏ ETMƏ SƏKƏLİYİNİ LƏND EDƏ BİLƏR.

ZƏMANƏT, XİDMƏT VƏ YA YENİDƏN KALİBRASYON

Zəmanət, xidmət və ya yenidən kalibrləmə üçün əlaqə saxlayın:

TRACEABLE® MƏHSULLARI
12554 Old Galveston Rd. Suite B230 • Webster, Texas 77598 ABŞ
Ph. 281 482-1714 • Faks 281 482-9448
E-poçt support@traceable.com • www.traceable.com

Traceable® Products are ISO 9001:2015 Quality-Certified by DNV and ISO/IEC 17025:2017 accredited as a Calibration Laboratory by A2LA.

TraceableLIVE® and TraceableGO™ are registered trademark/trademarks of Cole-Parmer.

©2020 Traceable® Products. 92-6535-20  Rev. 3 080725

Sənədlər / Resurslar

TRACEABLE CC653X Temperature Bluetooth Data Logger [pdf] Təlimatlar CC653X, CC653X Temperature Bluetooth Data Logger, Temperature Bluetooth Data Logger, Bluetooth Data Logger, Data Logger

İstinadlar

• İstifadəçi təlimatı