ಟ್ರೇಸಿಬಲ್ CC653X ತಾಪಮಾನ ಬ್ಲೂಟೂತ್ ಡೇಟಾ ಲಾಗರ್ ಸೂಚನೆಗಳು

DATALOGGER INSTRUCTIONS

ಪ್ರಮುಖ ಸೂಚನೆ

You MUST download one of the Mobile Apps below to retrieve data and configure device

---

ಬ್ಲೂಟೂತ್ ಮಾತ್ರ

---

Download TraceableGO™ App

---

---

Bluetooth + Cloud Data Storage

---

TraceableLIVE® Subscription REQUIRED

---

NOW that one of the apps below have been installed on your mobile device

TraceableGO comes ready to use out of the box.

TraceableGO™ App Free Download ಉಚಿತ ವೈಶಿಷ್ಟ್ಯಗಳು
	Configure datalogger: ಅಲಾರಂ ಹೊಂದಿಸಿ Change Logging Interval °C/°F ನಡುವೆ ಟಾಗಲ್ ಮಾಡಿ Start/Stop Options ಮೆಮೊರಿ ಸುತ್ತು
	Export, Email and Save PDF to Mobile Device
	UNLIMITED CLOUD DATA STORAGE
	Data download to CSV, or Secured PDF
	Graphical UI to analyze data
	Summary data display: Min/Max, Kinetic Mean, Time in Alarm
	Storage of trip parameters
	21 CFR 11 Compliance

TraceableLIVE® App ಉಚಿತ ಡೌನ್ಲೋಡ್ $30/ತಿಂಗಳು ವೈಶಿಷ್ಟ್ಯಗಳು
	Configure datalogger: ಅಲಾರಂ ಹೊಂದಿಸಿ Change Logging Interval °C/°F ನಡುವೆ ಟಾಗಲ್ ಮಾಡಿ Start/Stop Options ಮೆಮೊರಿ ಸುತ್ತು
	Export, Email and Save PDF to Mobile Device
	UNLIMITED CLOUD DATA STORAGE
	Data download to CSV, or Secured PDF
	Graphical UI to analyze data
	Summary data display: Min/Max, Kinetic Mean, Time in Alarm
	Storage of trip parameters
	21 CFR 11 Compliance

ಸಾಧನವನ್ನು ಕಾನ್ಫಿಗರ್ ಮಾಡಿ

ಸೂಚನೆ: To configure device either TraceableGO™ or TraceableLIVE® Apps must be downloaded to a mobile device.

ENABLE BLUETOOTH

1. Quick press twice START/STOP to enable Bluetooth, and Bluetooth LCD symbol appears.
2. Device starts to advertise to be found, and to be connected. Device Name shown on TraceableGO™ App discovered list looks like CC653X-xxxx, where “CC653X” indicates model number and “-xxxx” is last 4 digits of device serial number.
3. If no connection has been made for ಒಂದು ನಿಮಿಷ, Bluetooth will be disabled to save battery life, and Bluetooth LCD symbol disappears, or quick press twice again to disable Bluetooth.

TO VIEW PRE-CONFIGURED SETTINGS

1. Enable Bluetooth on device (see above).

2. Open TraceableGO™ or TraceableLIVE® App on any bluetooth enabled mobile device.
ಗಮನಿಸಿ: Mobile device must have Bluetooth enabled to receive signal. To enable Bluetooth on a mobile device see mobile device settings.

3. Use TraceableGO™ or TraceableLIVE® App to connect to device. Once the app is open it will begin searching for devices to connect to.

A list of available Dataloggers will appear.

ಗಮನಿಸಿ: TraceableGO Bluetooth Dataloggers are serialized and each logger name will match the sticker located on the side of the unit.

4. Once device is selected select Configure.

5. The following parameters are configured through App: START Mode, STOP Mode, ALARM Enable/Disable, Celsius/Fahrenheit, Memory Mode, Data Logging Interval, Alarm Setting.

6. TraceableGO™ comes pre-programmed. To view current settings, tap on configure once device is selected in App.

7. Device comes pre-configured as shown below:

a. ಸಾಧನದ ಹೆಸರು
b. ಸಾಧನದ ಸರಣಿ ಸಂಖ್ಯೆ
c. Current Battery Status
d. Current Temperature and/or Humidity Readings

PRE-CONFIGURED DEVICE SETTINGS

1. START Mode: Push Start
2. STOP Mode: Push Button Stop
3. Memory Mode: Wrap when Memory is Full
4. Unit Preferences: °C
5. Alarm Setting Alarm Low:
   TAP ON VALUE TO CHANGE
   ▪ Temperature: 2°C (6535 only)
   ▪ Temperature: 20°C (6537 only)
   ▪ Humidity: 25% RH (6537 only)
6. Alarm Setting High Alarm:
   TAP ON VALUE TO CHANGE
   ▪ Temperature: 8°C (6535 only)
   ▪ Temperature: 30°C (6537 only)
   ▪ Humidity: 75% RH (6537 only)
7. Alarm Enable/Disable: Enabled
8. Data Logging Interval: 5 minutes
9. Date/Time is also set to current to central time (Automatically updates when connected to mobile device).

Tap Configure to change factory settings

1. START Mode
ತಕ್ಷಣದ ಆರಂಭ: Once device is configured it will begin Datalogging.
ಪುಶ್ ಬಟನ್: Press START/STOP Button to begin Datalogging.
ವಿಳಂಬ: Select number of Hours, Minutes and Seconds when device is to begin Datalogging.

2. STOP Mode
ಎಂದಿಗೂ: Device will never stop Datalogging.
ಪುಶ್ ಬಟನ್: ಒತ್ತಿರಿ START/STOP Button to Stop Datalogging.

3. ಮೆಮೊರಿ ಮೋಡ್
Wrap When Full: Once memory is full, oldest data points will be overwritten with new data points.
Stop When Full: Device will stop recording when Memory is Full 64K (65,536) data points, 7.5 months on 5-minute logging interval.

4. Unit Preferences
° F: Select Fahrenheit
°C: Select Celsius

5. Alarm Setting Alarm Low: TAP ON VALUE TO CHANGE

• ತಾಪಮಾನ: Set LOWEST Temperature before an alarm is triggered.
• Humidity (6537 only): Set LOWEST Relative Humidity before an alarm is triggered.

6. Alarm Setting High Alarm: TAP ON VALUE TO CHANGE

• ತಾಪಮಾನ: Set HIGHEST Temperature before an alarm is triggered.
• Humidity (6537 only): Set HIGHEST Relative Humidity value before an alarm is triggered.

7. Alarm Enable/Disable
ಸಕ್ರಿಯಗೊಳಿಸಲಾಗಿದೆ: ಅಲಾರಾಂ ಆನ್ ಆಗಿದೆ.
ನಿಷ್ಕ್ರಿಯಗೊಳಿಸಲಾಗಿದೆ: ಅಲಾರಾಂ ಆಫ್ ಆಗಿದೆ.

8. Data Logging Interval
Slide to desired Logging Interval.

9. Save Configurations: ಪ್ರಸ್ತುತ ಸೆಟ್ಟಿಂಗ್‌ಗಳನ್ನು ಉಳಿಸುತ್ತದೆ.
ಸೂಚನೆ: Saving a Configuration will delete all data on device.

Once device has been configured, device enters STANDBY Mode.

Date/Time is also set to current to central time (Automatically updates when connected to mobile ಸಾಧನ).

HOW TO DOWNLOAD DATA TO MOBILE DEVICE

ಸೂಚನೆ: To download data either TraceableGO™ or TraceableLIVE Apps must be downloaded to a mobile device.

ENABLE BLUETOOTH

1. Quick press twice START/STOP to enable Bluetooth, and Bluetooth LCD symbol appears.
2. Device starts to advertise to be found, and to be connected. Device Name shown on TraceableGO™ App discovered list looks like CC653X-xxxx, where “CC653X” indicates model number and “-xxxx” is last 4 digits of device serial number.
3. If no connection has been made for ಒಂದು ನಿಮಿಷ, Bluetooth will be disabled to save battery life, and Bluetooth LCD symbol  disappears, or quick press twice again to disable Bluetooth.

TO DOWNLOAD RECORDED DATA

1. Device must be stopped. Enable Bluetooth on device (see above).

2. Open TraceableGO™ or TraceableLIVE® App on any bluetooth enabled mobile device. ಗಮನಿಸಿ: Mobile device must have Bluetooth enabled to receive signal. To enable Bluetooth on a mobile device see mobile device settings.

3. Use TraceableGO™ or TraceableLIVE® App to connect to device. Once the app is open it will begin searching for devices to connect to.

A list of available Dataloggers will appear.

ಗಮನಿಸಿ: TraceableGO™ Bluetooth Dataloggers are serialized and each logger name will match the sticker located on the side of the unit.

4. Once device is selected select Download Data.

5. App will begin extracting the data from TraceableGO™ Device.

6. Once data download is complete, mobile device will display options how to send PDF file, or CSV file (TraceableLIVE only). Tap Done and download is complete.

ವಿಶೇಷಣಗಳು

ಬೆಕ್ಕು ಸಂಖ್ಯೆ 6535

ಬೆಕ್ಕು ಸಂಖ್ಯೆ 6538

ಬೆಕ್ಕು ಸಂಖ್ಯೆ 6537

ತಾಪಮಾನ

6535: Ambient Range: -20.0 ರಿಂದ 70.0 ° C (-4.0 ರಿಂದ 158.0 ° F)
6536/6538 Probe Range: -50.0 ರಿಂದ 70.0 ° C (-58.0 ರಿಂದ 158.0 ° F)
6539 Probe Range: -90.00 ರಿಂದ 100.00 ° C (-130.00 ರಿಂದ 212.00 ° F)
ರೆಸಲ್ಯೂಶನ್: 0.1°C
ನಿಖರತೆ:
6535: ±0.4°C between -10 and 70°C, otherwise ±0.5°C
6536/6538: ±0.3°C
6539: ±0.2°C

RELATIVE HUMIDITY & TEMPERATURE

ತಾಪಮಾನ-
ಸುತ್ತುವರಿದ ಶ್ರೇಣಿ: –20.0 ರಿಂದ 70.0 ° C (–4.0 ರಿಂದ 158.0 ° F)
ರೆಸಲ್ಯೂಶನ್: 0.1°C
ನಿಖರತೆ: ±0.4°C between –10 and 70°C, otherwise ±0.5°C

Relative Humidity—
ಸುತ್ತುವರಿದ ಶ್ರೇಣಿ: 0% to 95%RH, non-condensing
ರೆಸಲ್ಯೂಶನ್: 0.1% RH
ನಿಖರತೆ: ±3% RH between 5 to 75%, otherwise ±5% RH

EXTERNAL PROBE

6536 Bullet Probe: Standard plastic probe sensor with cable. Designed for use in air and liquids, the sensor and cable may be completely immersed. Probe size: 3/16” diameter, 4/5” length; 10 foot cable

6538 Bottle Probe: Designed to simulate the temperature of stored liquids, use in transportation coolers, refrigerators and freezers. Bottle probes are filled with a patented nontoxic glycol solution that is GRAS (Generally Recognized As Safe) by the FDA (Food and Drug Administration) eliminating concerns about incidental contact with food or drinking water. The included micro-thin probe cable permits refrigerator/freezer doors to close on it. (Do not immerse bottle probes in liquid). Probe size: 1 x 2-1/2 inches; 10 foot cable.

6539 Stainless-Steel/Platinum Probe: Detachable stainless steel 316 Probe with Platinum Sensor and 9 feet of cable are supplied with the unit. Probe has a diameter of 1/8-inch, stem length of 6-1/4 inches, overall length of 9 inches.

ಬ್ಯಾಟರಿ: 2 AAA Alkaline batteries (3.0V)

ಆಯಾಮ: L x H x D: 3.5 x 2 x 0.79” (89 x 51 x 20 mm)

ಬ್ಯಾಟರಿ ಮಟ್ಟದ ಸೂಚನೆ:

ಬ್ಯಾಟರಿ ಮಟ್ಟ	LCD symbol
≥ 80% (2.78V)
≥ 60% (2.56V), < 80%
≥ 40% (2.34V), < 60%
≥ 20% (2.12V), < 40%
≥ 10% (2.01V), < 20%
< 10% Flashing

ಗಮನಿಸಿ: Battery level is updated every 5 minutes.

ಗಮನಿಸಿ: Once battery level drops to below 10%, device may not work properly. Replace batteries immediately.

ಗಮನಿಸಿ: When replacing batteries, after removing the old batteries, wait 10 seconds before inserting new batteries. Otherwise, Bluetooth may not work properly.

MEASUREMENT READING UPDATE FREQUENCY

Temperature and Humidity: 5 seconds;

ಗಮನಿಸಿ: If a reading is out of operating range, corresponding location on LCD will display ‘–.-‘, and such out of range reading will not trigger alarm.

DATA LOGGING FREQUENCY:

5 min by default, user-adjustable between 1 minute and 12 hours with 1 minute step.

DATA STORAGE CAPACITY

ಎಚ್ಚರಿಕೆ: Most recent 90 Alarm events

ಡೇಟಾ: 64K (65536) data points, 7.5 months on 5-minute logging interval

DEVICE OPERATING MODES

• IDLE Mode: First time battery inserted, and device has not been configured
• STANDBY Mode: Device has been configured, but not started;
• RUN Mode: Device starts to measure and log data.
• STOP Mode: Device stops from RUN Mode. In STOP Mode, device does not update measurements or log data, and the last measurements are displayed.

VIEW ಪ್ರಸ್ತುತ ಓದುವಿಕೆ

1. Temperature ONLY unit: Current reading, minimum/maximum reading, run time/alarm time toggling, Memory mode are shown on LCD.
2. Humidity and Temperature unit: Current temperature/humidity reading toggling every 5 seconds, minimum/maximum reading since last clearing, run time/alarm time, Memory mode are shown on LCD.

VIEW CURRENT MIN/MAX

Temperature ONLY unit: Current temperature Min/Max values are displayed on LCD. Humidity and Temperature unit: Current temperature/humidity Min/Max values are toggled display.

ಗಮನಿಸಿ: Every time device is configured, or resumes to run from STOP Mode, Min/Max values are reset.

VIEWING RUN TIME/ALARM TIME

Run Time/Alarm Time is toggled to display on LCD. If Run Time is displayed, LCD symbol ಸಮಯವನ್ನು ಚಲಾಯಿಸಿ appears; if Alarm Time is displayed, LCD symbol ಎಚ್ಚರಿಕೆಯ ಸಮಯ ಕಾಣಿಸಿಕೊಳ್ಳುತ್ತದೆ.

ಗಮನಿಸಿ: Alarm Time is accumulated for both Low Alarm and Hi Alarm for each channel (temperature, humidity).

ಮೆಮೊರಿ

If Memory Mode is set to WRAP WHEN FULL, appears on LCD; If Memory Mode is set to STOP WHEN FULL, MEM LCD ಯಲ್ಲಿ ಕಾಣಿಸಿಕೊಳ್ಳುತ್ತದೆ.

ಎಚ್ಚರಿಕೆ

1. Once an alarm is triggered by any of temperature, humidity out of set alarm range, LCD symbol LOW ALM ಮತ್ತು/ಅಥವಾ HI ALM starts to flash. An Alarm Event will be logged.
2. ಒತ್ತುವುದು START/STOP once will clear alarm, LCD symbol stops flashing. An Alarm Acknowledge Event will be logged.
3. If temperature, or humidity falls back to normal range, an Alarm Event will be logged. If any of temperature, humidity measurement goes back to out of alarm range, alarm will be triggered again.
4. If device’s START Mode is configured as PUSH BUTTON TO START (default), device LCD displays ‘push to start’. Press and hold START/STOP until LCD symbol appears. Device enters RUN Mode. If device’s START Mode is configured as IMMEDIATE START, device enters RUN Mode immediately. If device’s START Mode is configured as DELAYED TIME START, delayed start time set by user is counting down on device LCD. Once the counting time reaches 0, device enters RUN Mode.
5. ಒಳಗೆ ಇದ್ದರೆ ರನ್ ಮೋಡ್, LCD symbol ರನ್ appears, and logs data at user-defined interval. If STOP Mode is configured as PUSH BUTTON TO STOP, press and hold START/STOP until LCD symbol ನಿಲ್ಲಿಸು appears. Device enters STOP Mode. If STOP Mode is configured as NEVER STOP, device will ignore button press, and will stop when memory is full if Memory Mode is set to STOP WHEN FULL, or will stop when TraceableGO™ App is connected to device and downloads the data.
6. If in STOP Mode, press and hold START/STOP until LCD symbol ರನ್ appears. Device enters RUN Mode and resumes to log data at current setting. Anytime device resumes to log data from STOP Mode, Min/Max values are reset.

ಗಮನಿಸಿ: If device in STOP Mode, START Mode will be set to PUSH BUTTON TO START regardless of previous Start Mode Setting. If Delayed Start Mode is needed while device in STOP Mode, device must be re-configured.

ಗಮನಿಸಿ: While device is connected to TraceableGO™ App, once Device has received command from App to upload data to App, device will stop logging data and enter STOP Mode if it is still in RUN mode.

VIEW MEMORY USAGE, CURRENT DATE/TIME, DEVICE’S SERIAL NUMBER

1. ಒತ್ತಿ ಮತ್ತು ಬಿಡುಗಡೆ ಮಾಡಿ START/STOP ಬಟನ್

2. Memory usage in percentage is shown on LCD. The percentage indicates how much internal data memory storage has been used;

3. Number of days, hours, minutes left till memory is full are also displayed on the second line;

4. 10 ಸೆಕೆಂಡುಗಳಲ್ಲಿ, ಒತ್ತಿರಿ START/STOP again, current date/time is displayed on device LCD. The following figure shows 9/14/2017, 17:30

5. 10 ಸೆಕೆಂಡುಗಳಲ್ಲಿ, ಒತ್ತಿರಿ START/STOP again, device S/N will be displayed on LCD.

6. To return to normal working status, press START/STOP again, or wait for 10 seconds and device will automatically go back to normal working status.

ಗಮನಿಸಿ: If Memory Mode is set to WRAP WHEN FULL: LCD symbol starts to flash on the display when the memory is full. Once memory is full, the oldest data points will be overwritten with new data points.

If Memory Mode is set to STOP WHEN FULL: LCD symbol MEM starts to flash on the display when the memory is 95% full. Once memory is full, the device will stop logging new data points.

CLEAR DATA MEMORY STORAGE

1. Data points stored in device internal storage can only be cleared through App or battery removal.
2. Each time device is configured, all stored data points will be cleared.
3. Run Time/Alarm Time are also reset.

ನಿಯಮಿತ ಮಾಹಿತಿ

ಈ ಉಪಕರಣವನ್ನು ಪರೀಕ್ಷಿಸಲಾಗಿದೆ ಮತ್ತು ಎಫ್‌ಸಿಸಿ ನಿಯಮಗಳ ಭಾಗ 15 ರ ಪ್ರಕಾರ, ವರ್ಗ B ಡಿಜಿಟಲ್ ಸಾಧನದ ಮಿತಿಗಳನ್ನು ಅನುಸರಿಸಲು ಕಂಡುಬಂದಿದೆ. ವಸತಿ ಸ್ಥಾಪನೆಯಲ್ಲಿ ಹಾನಿಕಾರಕ ಹಸ್ತಕ್ಷೇಪದ ವಿರುದ್ಧ ಸಮಂಜಸವಾದ ರಕ್ಷಣೆಯನ್ನು ಒದಗಿಸಲು ಈ ಮಿತಿಗಳನ್ನು ವಿನ್ಯಾಸಗೊಳಿಸಲಾಗಿದೆ. ಈ ಉಪಕರಣವು ರೇಡಿಯೊ ತರಂಗಾಂತರ ಶಕ್ತಿಯನ್ನು ಉತ್ಪಾದಿಸುತ್ತದೆ, ಬಳಸುತ್ತದೆ ಮತ್ತು ವಿಕಿರಣಗೊಳಿಸುತ್ತದೆ ಮತ್ತು ಸೂಚನೆಗಳಿಗೆ ಅನುಗುಣವಾಗಿ ಸ್ಥಾಪಿಸದಿದ್ದರೆ ಮತ್ತು ಬಳಸಿದರೆ, ರೇಡಿಯೊ ಸಂವಹನಗಳಿಗೆ ಹಾನಿಕಾರಕ ಹಸ್ತಕ್ಷೇಪವನ್ನು ಉಂಟುಮಾಡಬಹುದು.

ಆದಾಗ್ಯೂ, ನಿರ್ದಿಷ್ಟ ಅನುಸ್ಥಾಪನೆಯಲ್ಲಿ ಹಸ್ತಕ್ಷೇಪ ಸಂಭವಿಸುವುದಿಲ್ಲ ಎಂಬುದಕ್ಕೆ ಯಾವುದೇ ಗ್ಯಾರಂಟಿ ಇಲ್ಲ. ಈ ಉಪಕರಣವು ರೇಡಿಯೋ ಅಥವಾ ಟೆಲಿವಿಷನ್ ಸ್ವಾಗತಕ್ಕೆ ಹಾನಿಕಾರಕ ಹಸ್ತಕ್ಷೇಪವನ್ನು ಉಂಟುಮಾಡಿದರೆ, ಉಪಕರಣವನ್ನು ಆಫ್ ಮತ್ತು ಆನ್ ಮಾಡುವ ಮೂಲಕ ನಿರ್ಧರಿಸಬಹುದು, ಈ ಕೆಳಗಿನ ಒಂದು ಅಥವಾ ಹೆಚ್ಚಿನ ಕ್ರಮಗಳ ಮೂಲಕ ಹಸ್ತಕ್ಷೇಪವನ್ನು ಸರಿಪಡಿಸಲು ಪ್ರಯತ್ನಿಸಲು ಬಳಕೆದಾರರನ್ನು ಪ್ರೋತ್ಸಾಹಿಸಲಾಗುತ್ತದೆ:

• ಸ್ವೀಕರಿಸುವ ಆಂಟೆನಾವನ್ನು ಮರುಹೊಂದಿಸಿ ಅಥವಾ ಸ್ಥಳಾಂತರಿಸಿ.
• ಉಪಕರಣ ಮತ್ತು ರಿಸೀವರ್ ನಡುವಿನ ಪ್ರತ್ಯೇಕತೆಯನ್ನು ಹೆಚ್ಚಿಸಿ.
• ರಿಸೀವರ್ ಸಂಪರ್ಕಗೊಂಡಿರುವುದಕ್ಕಿಂತ ವಿಭಿನ್ನವಾದ ಸರ್ಕ್ಯೂಟ್ನಲ್ಲಿನ ಔಟ್ಲೆಟ್ಗೆ ಉಪಕರಣವನ್ನು ಸಂಪರ್ಕಿಸಿ.
• ಸಹಾಯಕ್ಕಾಗಿ ಡೀಲರ್ ಅಥವಾ ಅನುಭವಿ ರೇಡಿಯೋ/ಟಿವಿ ತಂತ್ರಜ್ಞರನ್ನು ಸಂಪರ್ಕಿಸಿ.

ಈ ಸಾಧನವು FCC ನಿಯಮಗಳ ಭಾಗ 15 ಅನ್ನು ಅನುಸರಿಸುತ್ತದೆ. ಕಾರ್ಯಾಚರಣೆಯು ಈ ಕೆಳಗಿನ ಎರಡು ಷರತ್ತುಗಳಿಗೆ ಒಳಪಟ್ಟಿರುತ್ತದೆ: (1) ಈ ಸಾಧನವು ಹಾನಿಕಾರಕ ಹಸ್ತಕ್ಷೇಪವನ್ನು ಉಂಟುಮಾಡದಿರಬಹುದು, ಮತ್ತು (2) ಅನಪೇಕ್ಷಿತ ಕಾರ್ಯಾಚರಣೆಗೆ ಕಾರಣವಾಗಬಹುದಾದ ಹಸ್ತಕ್ಷೇಪ ಸೇರಿದಂತೆ ಸ್ವೀಕರಿಸಿದ ಯಾವುದೇ ಹಸ್ತಕ್ಷೇಪವನ್ನು ಈ ಸಾಧನವು ಸ್ವೀಕರಿಸಬೇಕು.

Hereby, Traceable Products, declares that this digital thermometer is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.

ಈ ಸಾಧನವು ಇಂಡಸ್ಟ್ರಿ ಕೆನಡಾ ಪರವಾನಗಿ-ವಿನಾಯಿತಿ RSS ಸ್ಟ್ಯಾಂಡರ್ಡ್(ಗಳು) ವನ್ನು ಅನುಸರಿಸುತ್ತದೆ. ಕಾರ್ಯಾಚರಣೆಯು ಈ ಕೆಳಗಿನ ಎರಡು ಷರತ್ತುಗಳಿಗೆ ಒಳಪಟ್ಟಿರುತ್ತದೆ: (1) ಈ ಸಾಧನವು ಹಸ್ತಕ್ಷೇಪವನ್ನು ಉಂಟುಮಾಡದಿರಬಹುದು, ಮತ್ತು (2) ಸಾಧನದ ಅನಪೇಕ್ಷಿತ ಕಾರ್ಯಾಚರಣೆಗೆ ಕಾರಣವಾಗಬಹುದಾದ ಹಸ್ತಕ್ಷೇಪ ಸೇರಿದಂತೆ ಯಾವುದೇ ಹಸ್ತಕ್ಷೇಪವನ್ನು ಈ ಸಾಧನವು ಸ್ವೀಕರಿಸಬೇಕು.

ಸೂಚನೆ: ಅನುಸರಣೆಗೆ ಜವಾಬ್ದಾರರಾಗಿರುವ ಪಕ್ಷದಿಂದ ಸ್ಪಷ್ಟವಾಗಿ ಅನುಮೋದಿಸದ ಯಾವುದೇ ಬದಲಾವಣೆಗಳು ಅಥವಾ ಮಾರ್ಪಾಡುಗಳಿಗೆ ಅನುದಾನವು ಜವಾಬ್ದಾರನಾಗಿರುವುದಿಲ್ಲ. ಅಂತಹ ಮಾರ್ಪಾಡುಗಳು ಸಲಕರಣೆಗಳನ್ನು ನಿರ್ವಹಿಸುವ ಬಳಕೆದಾರರ ಅಧಿಕಾರವನ್ನು ರದ್ದುಗೊಳಿಸಬಹುದು.

ವಾರಂಟಿ, ಸೇವೆ, ಅಥವಾ ಮರುಮಾಪನ

ಖಾತರಿ, ಸೇವೆ ಅಥವಾ ಮರುಮಾಪನಕ್ಕಾಗಿ, ಸಂಪರ್ಕಿಸಿ:

ಪತ್ತೆಹಚ್ಚಬಹುದಾದ ® ಉತ್ಪನ್ನಗಳು
12554 Old Galveston Rd. Suite B230 • Webಸ್ಟರ್, ಟೆಕ್ಸಾಸ್ 77598 ಯುಎಸ್ಎ
Ph. 281 482-1714 • ಫ್ಯಾಕ್ಸ್ 281 482-9448
ಇಮೇಲ್ support@traceable.com • www.traceable.com

Traceable® Products are ISO 9001:2015 Quality-Certified by DNV and ISO/IEC 17025:2017 accredited as a Calibration Laboratory by A2LA.

TraceableLIVE® and TraceableGO™ are registered trademark/trademarks of Cole-Parmer.

©2020 Traceable® Products. 92-6535-20  Rev. 3 080725

ದಾಖಲೆಗಳು / ಸಂಪನ್ಮೂಲಗಳು

TRACEABLE CC653X Temperature Bluetooth Data Logger [ಪಿಡಿಎಫ್] ಸೂಚನೆಗಳು CC653X, CC653X Temperature Bluetooth Data Logger, Temperature Bluetooth Data Logger, Bluetooth Data Logger, Data Logger

ಉಲ್ಲೇಖಗಳು

• ಬಳಕೆದಾರ ಕೈಪಿಡಿ