DATALOGGER INSTRUCTIONS

TSEEM CEEB

You MUST download one of the Mobile Apps below to retrieve data and configure device

---

Bluetooth nkaus xwb

---

Download TraceableGO™ App

---

---

Bluetooth + Cloud Data Storage

---

TraceableLIVE® Subscription REQUIRED

---

NOW that one of the apps below have been installed on your mobile device

TraceableGO comes ready to use out of the box.

TraceableGO™ App Free Download DAWB Nta
	Configure datalogger: Teeb Tswb Change Logging Interval Toggle ntawm ° C / ° F Start/Stop Options Memory qhwv
	Export, Email and Save PDF to Mobile Device
	UNLIMITED CLOUD DATA STORAGE
	Data download to CSV, or Secured PDF
	Graphical UI to analyze data
	Summary data display: Min/Max, Kinetic Mean, Time in Alarm
	Storage of trip parameters
	21 CFR 11 Compliance

TraceableLIVE® App Dawb download tau $30/ hli Nta
	Configure datalogger: Teeb Tswb Change Logging Interval Toggle ntawm ° C / ° F Start/Stop Options Memory qhwv
	Export, Email and Save PDF to Mobile Device
	UNLIMITED CLOUD DATA STORAGE
	Data download to CSV, or Secured PDF
	Graphical UI to analyze data
	Summary data display: Min/Max, Kinetic Mean, Time in Alarm
	Storage of trip parameters
	21 CFR 11 Compliance

CONFIGURE Device

CEEB TOOM: To configure device either TraceableGO™ or TraceableLIVE® Apps must be downloaded to a mobile device.

ENABLE BLUETOOTH

1. Quick press twice START/STOP to enable Bluetooth, and Bluetooth LCD symbol appears.
2. Device starts to advertise to be found, and to be connected. Device Name shown on TraceableGO™ App discovered list looks like CC653X-xxxx, where “CC653X” indicates model number and “-xxxx” is last 4 digits of device serial number.
3. If no connection has been made for IB QHOV, Bluetooth will be disabled to save battery life, and Bluetooth LCD symbol disappears, or quick press twice again to disable Bluetooth.

TO VIEW PRE-CONFIGURED SETTINGS

1. Enable Bluetooth on device (see above).

2. Open TraceableGO™ or TraceableLIVE® App on any bluetooth enabled mobile device.
Nco tseg: Mobile device must have Bluetooth enabled to receive signal. To enable Bluetooth on a mobile device see mobile device settings.

3. Use TraceableGO™ or TraceableLIVE® App to connect to device. Once the app is open it will begin searching for devices to connect to.

A list of available Dataloggers will appear.

Nco tseg: TraceableGO Bluetooth Dataloggers are serialized and each logger name will match the sticker located on the side of the unit.

4. Once device is selected select Configure.

5. The following parameters are configured through App: START Mode, STOP Mode, ALARM Enable/Disable, Celsius/Fahrenheit, Memory Mode, Data Logging Interval, Alarm Setting.

6. TraceableGO™ comes pre-programmed. To view current settings, tap on configure once device is selected in App.

7. Device comes pre-configured as shown below:

a. Ntaus lub npe
b. Ntaus Serial Number
c. Current Battery Status
d. Current Temperature and/or Humidity Readings

PRE-CONFIGURED DEVICE SETTINGS

1. START Mode: Push Start
2. STOP Mode: Push Button Stop
3. Memory Mode: Wrap when Memory is Full
4. Unit Preferences: °C
5. Alarm Setting Alarm Low:
   TAP ON VALUE TO CHANGE
   ▪ Temperature: 2°C (6535 only)
   ▪ Temperature: 20°C (6537 only)
   ▪ Humidity: 25% RH (6537 only)
6. Alarm Setting High Alarm:
   TAP ON VALUE TO CHANGE
   ▪ Temperature: 8°C (6535 only)
   ▪ Temperature: 30°C (6537 only)
   ▪ Humidity: 75% RH (6537 only)
7. Alarm Enable/Disable: Enabled
8. Data Logging Interval: 5 minutes
9. Date/Time is also set to current to central time (Automatically updates when connected to mobile device).

Tap Configure to change factory settings

1. START Mode
Pib tam sim: Once device is configured it will begin Datalogging.
Push Button: Press START/STOP Button to begin Datalogging.
ncua: Select number of Hours, Minutes and Seconds when device is to begin Datalogging.

2. STOP Mode
Tsis txhob: Device will never stop Datalogging.
Push Button: Xovxwm PIB/STOP Button to Stop Datalogging.

3. Cim xeeb hom
Wrap When Full: Once memory is full, oldest data points will be overwritten with new data points.
Stop When Full: Device will stop recording when Memory is Full 64K (65,536) data points, 7.5 months on 5-minute logging interval.

4. Unit Preferences
° F: Select Fahrenheit
°C: Select Celsius

5. Alarm Setting Alarm Low: TAP ON VALUE TO CHANGE

• Kub: Set LOWEST Temperature before an alarm is triggered.
• Humidity (6537 only): Set LOWEST Relative Humidity before an alarm is triggered.

6. Alarm Setting High Alarm: TAP ON VALUE TO CHANGE

• Kub: Set HIGHEST Temperature before an alarm is triggered.
• Humidity (6537 only): Set HIGHEST Relative Humidity value before an alarm is triggered.

7. Alarm Enable/Disable
Enabled: Tswb yog nyob.
Neeg xiam: Tswb raug kaw lawm.

8. Data Logging Interval
Slide to desired Logging Interval.

9. Save Configurations: Txuag cov kev teeb tsa tam sim no.
CEEB TOOM: Saving a Configuration will delete all data on device.

Once device has been configured, device enters STANDBY Mode.

Date/Time is also set to current to central time (Automatically updates when connected to mobile cuab yeej).

HOW TO DOWNLOAD DATA TO MOBILE DEVICE

CEEB TOOM: To download data either TraceableGO™ or TraceableLIVE Apps must be downloaded to a mobile device.

ENABLE BLUETOOTH

1. Quick press twice START/STOP to enable Bluetooth, and Bluetooth LCD symbol appears.
2. Device starts to advertise to be found, and to be connected. Device Name shown on TraceableGO™ App discovered list looks like CC653X-xxxx, where “CC653X” indicates model number and “-xxxx” is last 4 digits of device serial number.
3. If no connection has been made for IB QHOV, Bluetooth will be disabled to save battery life, and Bluetooth LCD symbol  disappears, or quick press twice again to disable Bluetooth.

TO DOWNLOAD RECORDED DATA

1. Device must be stopped. Enable Bluetooth on device (see above).

2. Open TraceableGO™ or TraceableLIVE® App on any bluetooth enabled mobile device. Nco tseg: Mobile device must have Bluetooth enabled to receive signal. To enable Bluetooth on a mobile device see mobile device settings.

3. Use TraceableGO™ or TraceableLIVE® App to connect to device. Once the app is open it will begin searching for devices to connect to.

A list of available Dataloggers will appear.

Nco tseg: TraceableGO™ Bluetooth Dataloggers are serialized and each logger name will match the sticker located on the side of the unit.

4. Once device is selected select Download Data.

5. App will begin extracting the data from TraceableGO™ Device.

6. Once data download is complete, mobile device will display options how to send PDF file, or CSV file (TraceableLIVE only). Tap Done and download is complete.

SPECIFICATIONS

Miv. Tsis muaj. 6535

Miv. Tsis muaj. 6538

Miv. Tsis muaj. 6537

KUB

6535: Ambient Range: -20.0 txog 70.0 ° C (-4.0 txog 158.0 ° F)
6536/6538 Probe Range: -50.0 txog 70.0 ° C (-58.0 txog 158.0 ° F)
6539 Probe Range: -90.00 txog 100.00 ° C (-130.00 txog 212.00 ° F)
Kev daws teeb meem: 0.1 ° C
Qhov tseeb:
6535: ±0.4°C between -10 and 70°C, otherwise ±0.5°C
6536/6538: ± 0.3 ° C
6539: ± 0.2 ° C

RELATIVE HUMIDITY & TEMPERATURE

Kub -
Ambient Range: –20.0 txog 70.0 ° C (to4.0 txog 158.0 ° F)
Kev daws teeb meem: 0.1 ° C
Qhov tseeb: ±0.4°C between –10 and 70°C, otherwise ±0.5°C

Relative Humidity—
Ambient Range: 0% to 95%RH, non-condensing
Kev daws teeb meem: 0.1% RH
Qhov tseeb: ±3% RH between 5 to 75%, otherwise ±5% RH

EXTERNAL PROBE

6536 Bullet Probe: Standard plastic probe sensor with cable. Designed for use in air and liquids, the sensor and cable may be completely immersed. Probe size: 3/16” diameter, 4/5” length; 10 foot cable

6538 Bottle Probe: Designed to simulate the temperature of stored liquids, use in transportation coolers, refrigerators and freezers. Bottle probes are filled with a patented nontoxic glycol solution that is GRAS (Generally Recognized As Safe) by the FDA (Food and Drug Administration) eliminating concerns about incidental contact with food or drinking water. The included micro-thin probe cable permits refrigerator/freezer doors to close on it. (Do not immerse bottle probes in liquid). Probe size: 1 x 2-1/2 inches; 10 foot cable.

6539 Stainless-Steel/Platinum Probe: Detachable stainless steel 316 Probe with Platinum Sensor and 9 feet of cable are supplied with the unit. Probe has a diameter of 1/8-inch, stem length of 6-1/4 inches, overall length of 9 inches.

Roj teeb: 2 AAA Alkaline batteries (3.0V)

Dimension: L x H x D: 3.5 x 2 x 0.79” (89 x 51 x 20 mm)

Roj teeb theem qhia:

Roj teeb theem	LCD symbol
≥ 80% (2.78V)
≥ 60% (2.56V), < 80%
≥ 40% (2.34V), < 60%
≥ 20% (2.12V), < 40%
≥ 10% (2.01V), < 20%
< 10% Flashing

Nco tseg: Battery level is updated every 5 minutes.

Nco tseg: Once battery level drops to below 10%, device may not work properly. Replace batteries immediately.

Nco tseg: When replacing batteries, after removing the old batteries, wait 10 seconds before inserting new batteries. Otherwise, Bluetooth may not work properly.

MEASUREMENT READING UPDATE FREQUENCY

Temperature and Humidity: 5 seconds;

Nco tseg: If a reading is out of operating range, corresponding location on LCD will display ‘–.-‘, and such out of range reading will not trigger alarm.

DATA LOGGING FREQUENCY:

5 min by default, user-adjustable between 1 minute and 12 hours with 1 minute step.

DATA STORAGE CAPACITY

Tswb: Most recent 90 Alarm events

Cov ntaub ntawv: 64K (65536) data points, 7.5 months on 5-minute logging interval

DEVICE OPERATING MODES

• IDLE Mode: First time battery inserted, and device has not been configured
• STANDBY Mode: Device has been configured, but not started;
• RUN Mode: Device starts to measure and log data.
• STOP Mode: Device stops from RUN Mode. In STOP Mode, device does not update measurements or log data, and the last measurements are displayed.

VIEW Tam sim no nyeem ntawv

1. Temperature ONLY unit: Current reading, minimum/maximum reading, run time/alarm time toggling, Memory mode are shown on LCD.
2. Humidity and Temperature unit: Current temperature/humidity reading toggling every 5 seconds, minimum/maximum reading since last clearing, run time/alarm time, Memory mode are shown on LCD.

VIEW CURRENT MIN/MAX

Temperature ONLY unit: Current temperature Min/Max values are displayed on LCD. Humidity and Temperature unit: Current temperature/humidity Min/Max values are toggled display.

Nco tseg: Every time device is configured, or resumes to run from STOP Mode, Min/Max values are reset.

VIEWING RUN TIME/ALARM TIME

Run Time/Alarm Time is toggled to display on LCD. If Run Time is displayed, LCD symbol ROV SIJHAWM appears; if Alarm Time is displayed, LCD symbol TEJ SIJHAWM tshwm.

Nco tseg: Alarm Time is accumulated for both Low Alarm and Hi Alarm for each channel (temperature, humidity).

MEMORY

If Memory Mode is set to WRAP WHEN FULL, appears on LCD; If Memory Mode is set to STOP WHEN FULL, MEM tshwm ntawm LCD.

Tswb

1. Once an alarm is triggered by any of temperature, humidity out of set alarm range, LCD symbol LOW ALM thiab/los yog HI ALM starts to flash. An Alarm Event will be logged.
2. Nias PIB/STOP once will clear alarm, LCD symbol stops flashing. An Alarm Acknowledge Event will be logged.
3. If temperature, or humidity falls back to normal range, an Alarm Event will be logged. If any of temperature, humidity measurement goes back to out of alarm range, alarm will be triggered again.
4. If device’s START Mode is configured as PUSH BUTTON TO START (default), device LCD displays ‘push to start’. Press and hold PIB/STOP until LCD symbol appears. Device enters RUN Mode. If device’s START Mode is configured as IMMEDIATE START, device enters RUN Mode immediately. If device’s START Mode is configured as DELAYED TIME START, delayed start time set by user is counting down on device LCD. Once the counting time reaches 0, device enters RUN Mode.
5. Yog nyob rau hauv Khiav hom, LCD symbol Khiav appears, and logs data at user-defined interval. If STOP Mode is configured as PUSH BUTTON TO STOP, press and hold PIB/STOP until LCD symbol TSIS TAU appears. Device enters STOP Mode. If STOP Mode is configured as NEVER STOP, device will ignore button press, and will stop when memory is full if Memory Mode is set to STOP WHEN FULL, or will stop when TraceableGO™ App is connected to device and downloads the data.
6. If in STOP Mode, press and hold PIB/STOP until LCD symbol Khiav appears. Device enters RUN Mode and resumes to log data at current setting. Anytime device resumes to log data from STOP Mode, Min/Max values are reset.

Nco tseg: If device in STOP Mode, START Mode will be set to PUSH BUTTON TO START regardless of previous Start Mode Setting. If Delayed Start Mode is needed while device in STOP Mode, device must be re-configured.

Nco tseg: While device is connected to TraceableGO™ App, once Device has received command from App to upload data to App, device will stop logging data and enter STOP Mode if it is still in RUN mode.

VIEW MEMORY USAGE, CURRENT DATE/TIME, DEVICE’S SERIAL NUMBER

1. Nias thiab tso tawm PIB/STOP khawm

2. Memory usage in percentage is shown on LCD. The percentage indicates how much internal data memory storage has been used;

3. Number of days, hours, minutes left till memory is full are also displayed on the second line;

4. Tsis pub dhau 10 vib nas this, nias PIB/STOP again, current date/time is displayed on device LCD. The following figure shows 9/14/2017, 17:30

5. Tsis pub dhau 10 vib nas this, nias PIB/STOP again, device S/N will be displayed on LCD.

6. To return to normal working status, press PIB/STOP again, or wait for 10 seconds and device will automatically go back to normal working status.

Nco tseg: If Memory Mode is set to WRAP WHEN FULL: LCD symbol starts to flash on the display when the memory is full. Once memory is full, the oldest data points will be overwritten with new data points.

If Memory Mode is set to STOP WHEN FULL: LCD symbol MEM starts to flash on the display when the memory is 95% full. Once memory is full, the device will stop logging new data points.

CLEAR DATA MEMORY STORAGE

1. Data points stored in device internal storage can only be cleared through App or battery removal.
2. Each time device is configured, all stored data points will be cleared.
3. Run Time/Alarm Time are also reset.

COV NTAUB NTAWV TXOJ CAI

Cov cuab yeej no tau raug sim thiab pom tias ua raws li cov kev txwv rau Class B cov cuab yeej digital, ua raws li Tshooj 15 ntawm FCC Cov Cai. Cov kev txwv no yog tsim los muab kev tiv thaiv tsim nyog tiv thaiv kev cuam tshuam tsis zoo hauv kev teeb tsa hauv tsev. Cov cuab yeej no tsim, siv thiab tuaj yeem tawg lub zog ntawm xov tooj cua thiab, yog tias tsis tau nruab thiab siv raws li cov lus qhia, yuav ua rau muaj kev cuam tshuam rau kev sib txuas lus hauv xov tooj cua.

Txawm li cas los xij, tsis muaj kev lees paub tias kev cuam tshuam yuav tsis tshwm sim hauv ib qho kev teeb tsa tshwj xeeb. Yog tias cov cuab yeej no ua rau muaj teeb meem cuam tshuam rau lub xov tooj cua lossis TV txais tos, uas tuaj yeem txiav txim siab los ntawm kev tig cov khoom siv thiab qhib, tus neeg siv tau raug txhawb kom sim kho qhov cuam tshuam los ntawm ib lossis ntau qhov kev ntsuas hauv qab no:

• Reorient los yog tshem tawm cov kav hlau txais xov.
• Ua kom muaj kev sib cais ntawm cov khoom siv thiab lub receiver.
• Txuas cov cuab yeej siv rau hauv qhov hluav taws xob ntawm lub voj voog sib txawv ntawm qhov uas lub receiver txuas nrog.
• Nrog rau tus neeg muag khoom lossis tus kws tshaj lij xov tooj cua / TV rau kev pab.

Cov cuab yeej no ua raws li Tshooj 15 ntawm FCC Cov Cai. Kev khiav hauj lwm yog ua raws li ob qho xwm txheej hauv qab no: (1) cov cuab yeej no yuav tsis ua rau muaj kev cuam tshuam tsis zoo, thiab (2) cov cuab yeej no yuav tsum lees txais ib qho kev cuam tshuam uas tau txais, suav nrog kev cuam tshuam uas yuav ua rau kev ua haujlwm tsis zoo.

Hereby, Traceable Products, declares that this digital thermometer is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.

Cov cuab yeej no ua raws li Kev Lag Luam Canada daim ntawv tso cai-tsim RSS tus qauv (s). Kev khiav hauj lwm yog ua raws li ob qho xwm txheej hauv qab no: (1) cov cuab yeej no yuav tsis ua rau muaj kev cuam tshuam, thiab (2) cov cuab yeej no yuav tsum lees txais kev cuam tshuam, suav nrog kev cuam tshuam uas yuav ua rau lub tshuab ua haujlwm tsis xav tau.

CEEB TOOM: PAUB TIAS YUAV TSUM PAUB TXOG KEV THOV VAJTSWV COV LUS UAS YUAV TSUM PAUB TXOG TXOJ CAI NTAWM LUB SIJ HAWM NTAWM LUB SIJ HAWM TXOJ CAI. Cov kev hloov kho zoo li no tuaj yeem ua rau tus neeg siv txoj cai tswj hwm kev ua haujlwm ntawm cov khoom siv.

WARRANTY, SERVICE, LOSSIS RECALIBRATION

Rau warranty, kev pab cuam, los yog recalibration, hu rau:

TRACEABLE® PRODUCTS
12554 Old Galveston Rd. Suite B230 • Webster, TX 77598 USA
Ph. 281 482-1714 • Fax 281 482-9448
E-mail support@traceable.com • www.traceable.com ua

Cov khoom lag luam Traceable® yog ISO 9001: 2015 Zoo-Certified los ntawm DNV thiab ISO / IEC 17025: 2017 tau lees paub raws li Kev Ntsuas Ntsuas los ntawm A2LA.

TraceableLIVE® and TraceableGO™ are registered trademark/trademarks of Cole-Parmer.

©2020 Traceable® Products. 92-6535-20  Rev. 3 080725

Cov ntaub ntawv / Cov ntaub ntawv

TRACEABLE CC653X Temperature Bluetooth Data Logger [ua pdf] Cov lus qhia CC653X, CC653X Temperature Bluetooth Data Logger, Temperature Bluetooth Data Logger, Bluetooth Data Logger, Data Logger

Cov ntaub ntawv

• Cov neeg siv phau ntawv