VEVOR Reception Desk
Model: SS-602
Tagline: TOUGH TOOLS, HALF PRICE
For Technical Support and E-Warranty Certificate, visit: www.vevor.com/support
Introduction
This is the user manual for the VEVOR Reception Desk, Model SS-602. VEVOR is committed to providing tools at competitive prices. The expressions like "Save Half" or "Half Price" represent an estimate of potential savings compared to major brands and may not apply to all product categories. Customers are advised to verify savings carefully when placing an order.
Please read all manual instructions carefully before operating the product. VEVOR reserves the right to interpret the user manual. The appearance of the product is subject to the item received. Updates to technology or software may occur without prior notification.
Safety Instructions
WARNING:
Read this material before using this product. Failure to do so can result in serious injury.
Assembly Precautions:
- Assemble only according to these instructions. Improper assembly can create hazards.
- Wear ANSI-approved safety goggles and heavy-duty work gloves during assembly.
- Keep the assembly area clean and well-lit.
- Keep bystanders out of the area during assembly.
- Do not assemble if tired or under the influence of alcohol, drugs, or medication.
- Product capabilities apply only to properly and completely assembled products.
- Assemble on a flat, level, hard, and smooth surface capable of safely supporting the Reception Desk.
- For additional information regarding parts, refer to the Assembly Diagram. Unwrap and separate all parts in a clean work area.
Use Precautions:
- DO NOT SIT OR STAND ON THIS ITEM.
- This product is not a toy. Do not allow children to play with or near this item.
- Do not exceed specified weight capacities.
- Use only on a flat, level, hard, and smooth surface that can safely support a fully loaded Reception Desk.
- Use as intended only.
- Inspect before every use; do not use if parts are loose or damaged.
SAVE THIS MANUAL
Important Information
Please read the entire manual before starting to assemble and/or using this product. Follow the manual thoroughly and keep it for further reference.
Avoid Scratches:
To prevent scratching, this furniture should be assembled on a soft layer, such as a rug.
Improve Efficiency:
Try to find a partner to install with you, which can speed up the installation efficiency and shorten the time.
Anti-Topple Warning:
Overturned furniture can cause serious or fatal crush injuries. To prevent tipping over, be sure to use the wall attachment. If it is not included with this product, please purchase a wall attachment that fits your wall. If unsure, seek professional advice. Please read and follow each step of the instructions carefully.
Important Maintenance Note:
It is important that any product assembled using screws is re-tightened 2 weeks after assembly, and once every 3 months, to ensure stability throughout the product's lifespan.
For regular maintenance and cleaning: For the frame, use a rag dipped in neutral detergent to wipe it, then dry with a clean rag. For glass materials, wipe with a rag dampened with glass cleaner, and then dry with a dry rag.
Do not use an electric screwdriver, and do not use excessive force when installing, as the board is easy to break.
Parts List
The following parts and hardware are included in the package:
Parts:
- Part 1: Side Frame (x2)
- Part 2: Front Crossbar (x1)
- Part 3: Rear Crossbar (x1)
- Part 4: Middle Crossbar (x1)
- Part 5: Shelf (x3)
- Part 6: Small Support (x1)
- Part 8: Vertical Support (x2)
- Part 9: Left Side Panel (x1)
- Part 10: Right Side Panel (x1)
- Part 11: Upper Back Panel (x1)
- Part 12: Lower Back Panel (x1)
- Part 13: Front Top Trim (x1)
- Part 14: Desktop (x1)
Hardware:
- Hardware A: M5x42 Screws (42 PCS)
- Hardware B: 15x12 Screws (42 PCS)
- Hardware C: M7x50 Screws (26 PCS)
- Hardware D: M6x12 Screws (2 PCS)
- Hardware E: M6x25 Screws (25 PCS)
- Hardware F: M6x40 Screws (12 PCS)
- Part 7: Cam Dowel (x4)
- Part 17: Cam Lock (x6)
- Part 18: LED Light Strip (x1)
- Part G: Light Strip Connector (x6)
- Hardware H: Allen Wrench (x1)
Cam Lock Fastening System
This Cam Lock Fastening System will be used throughout the assembly process. The system involves inserting a cam dowel into one panel and a cam lock into another, then connecting them and turning the cam lock to secure the joint.
How to use:
- Insert the cam dowel (Part 7) into the pre-drilled hole on one panel.
- Insert the cam lock (Part 17) into the larger hole on the connecting panel, ensuring the arrow on the cam lock points towards the entry hole for the dowel.
- Align the panels so the cam dowel enters the cam lock.
- Turn the cam lock clockwise using a screwdriver to tighten the connection.
Assembly Steps
Step 1: Prepare Vertical Supports
Attach Cam Locks (Part 17) to the Vertical Supports (Part 8). Insert M7x50 screws (Part C) into the designated holes on Part 8, and then attach the Cam Locks (Part 17) to these screws. The diagram shows two assemblies, each with two vertical supports, where the cam lock dowels are inserted into pre-drilled holes on the supports, and then secured with screws.
Step 2: Attach Middle Crossbar to Side Panel
Connect a Side Panel (Part 15) to the Middle Crossbar (Part 4). Use M5x42 screws (Part A) and 15x12 screws (Part B) for this connection. The diagram shows the panel being attached to the crossbar, with screws indicated at multiple points.
Step 3: Attach Shelf to Side Panel
Attach another Side Panel (Part 15) to a Shelf (Part 5) using 15x12 screws (Part B). The diagram shows the panel being attached to the shelf, with screws indicated.
Step 4: Attach Shelf to Side Panel
Attach a Side Panel (Part 15) to a Shelf (Part 5) using M7x50 screws (Part C). The diagram shows the panel being attached to the shelf, with screws indicated.
Step 5: Connect Vertical Supports to Panels/Shelves
Connect the Vertical Supports (Part 8) to the Side Panels (Part 15) and Shelves (Part 5) using M7x50 screws (Part C). The diagram shows the vertical supports being attached to the assembled side panels and shelves, securing them together.
Step 6: Assemble Frame Base
Assemble the base frame by attaching the Side Frames (Part 1) to the Front Crossbar (Part 2) and Rear Crossbar (Part 3) using M6x40 screws (Part F). The diagram shows the two side frames being connected by the front and rear crossbars.
Step 7: Attach Middle Crossbar to Frame
Attach the Middle Crossbar (Part 4) to the assembled frame base using M6x40 screws (Part F). The diagram shows the middle crossbar being secured between the side frames.
Step 8: Add Rear Supports
Attach the Rear Crossbar (Part 3) and Small Support (Part 6) to the frame structure. Use M6x40 screws (Part F) and M6x12 screws (Part D) for these connections. The diagram shows these parts being added to the rear of the desk structure.
Step 9: Attach Desktop
Place the Desktop (Part 14) onto the assembled frame. Secure it using M6x25 screws (Part E) and M6x40 screws (Part F). The diagram shows the desktop being placed on top and screws being inserted from underneath into the frame.
Step 10: Attach Side Panels to Desktop
Attach the Left Side Panel (Part 9) and Right Side Panel (Part 10) to the Desktop (Part 14). Use M5x42 screws (Part A) for this step. The diagram shows the side panels being attached vertically to the underside of the desktop.
Step 11: Secure Side Panels to Frame
Further secure the Side Panels (Part 9 and Part 10) to the main frame structure. Use 15x12 screws (Part B) and M6x25 screws (Part E). The diagram illustrates these connections being made to reinforce the structure.
Step 12: Attach Back Panels
Attach the Upper Back Panel (Part 11) and Lower Back Panel (Part 12) to the rear of the reception desk. Use M5x42 screws (Part A) for this attachment. The diagram shows the back panels being fitted into place.
Step 13: Final Panel Securing
Secure the side and back panels using Cam Locks (Part 17) and 15x12 screws (Part B). This step reinforces the connections made in previous steps. The diagram indicates the use of cam locks and screws at various points on the side and back panels. It also shows an icon representing two people, suggesting assistance may be helpful.
Step 14: Attach Front Top Trim
Attach the Front Top Trim (Part 13) to the front edge of the desktop. Use M5x42 screws (Part A) and the Allen Wrench (Hardware H). The diagram shows the trim piece being screwed into place on the front of the desktop. It also shows the attachment of a shelf (Part 5) and another structural part (Part 16) using screws.
Step 15: Install Cam Dowels
Install Cam Dowels (Part 7) into the Side Frames (Part 1). Use M6x25 screws (Part E) to secure them. The diagram shows the dowels being screwed into the side frames.
Step 16: Install LED Light Strip
Install the LED Light Strip (Part 18) and Light Strip Connectors (Part G) to the underside of the Front Top Trim (Part 13). The diagram shows the light strip being adhered to the back of the trim piece and connectors being attached. Text instructions state: "Carefully remove the plastic film behind the light strip." and "Note that G can be installed or not according to personal needs. G is used for the stick-off configuration of the light strip."
Product Parameters
| Model | SS-602 |
|---|---|
| Safe Loading Weight | 50kg |
| Colour | Black + Brown |
| Product Size | 1600*600*1110mm |
Manufacturer and Representative Information
Manufacturer: Shanghaimuxinmuyeyouxiangongsi
Address: Shuangchenglu 803nong11hao1602A-1609shi, baoshanqu, shanghai 200000 CN.
Imported to AUS: SIHAO PTY LTD. 1 ROKEVA STREETEASTWOOD NSW 2122 Australia
Imported to USA: Sanven Technology Ltd. Suite 250, 9166 Anaheim Place, Rancho Cucamonga, CA 91730
EU Representative: E-CrossStu GmbH, Mainzer Landstr.69, 60329 Frankfurt am Main.
UK Representative: YH CONSULTING LIMITED. C/O YH Consulting Limited Office 147, Centurion House, London Road, Staines-upon-Thames, Surrey, TW18 4AX
Contact Us â Official VEVOR Support
