Introduction

VEVOR is committed to providing tools at competitive prices. The phrases "Save Half" and "Half Price" represent an estimate of potential savings compared to major brands and may not apply to all product categories. Customers are advised to verify savings when placing orders.

Contact Us

For product questions or technical support, please contact:

? CustomerService@vevor.com

This manual is the original instruction. VEVOR reserves the right to interpret the user manual. Product appearance may vary from the received item. VEVOR will not provide separate notification for technology or software updates.

Safety Instructions

WARNING

Read this material before using this product. Failure to do so can result in serious injury.

Assembly Precautions

• Assemble only according to these instructions. Improper assembly can create hazards.
• Wear ANSI-approved safety goggles and heavy-duty work gloves during assembly.
• Keep the assembly area clean and well-lit.
• Keep bystanders out of the area during assembly.
• Do not assemble when tired or under the influence of alcohol, drugs, or medication.
• Product capabilities apply only to properly and completely assembled products.
• Assemble on a flat, level, hard, and smooth surface capable of safely supporting the Office Workbench.
• Refer to the Assembly Diagram for parts. Unwrap and separate all parts in a clean work area.

Use Precautions

• DO NOT SIT OR STAND ON THIS ITEM.
• This product is not a toy. Do not allow children to play with or near it.
• Do not exceed weight capacities.
• Use only on a flat, level, hard, and smooth surface capable of safely supporting a fully loaded Office Workbench.
• Use as intended only.
• Inspect before every use; do not use if parts are loose or damaged.

SAVE THIS MANUAL

Parts List

The workbench components include a tabletop (B), a central support column (A) with an adjustment lever, a base frame (C) with wheels, and a mounting plate (D) connecting the column to the tabletop.

Hardware and Components:

Assembly Steps

Step 1: Attach Mounting Plate to Support Column

Attach the mounting plate (D) to the top of the support column (A) using four M6x25mm screws (E) and one washer (H). Ensure the adjustment lever is oriented correctly.

Step 2: Attach Support Column Assembly to Tabletop

Place the tabletop (B) upside down. Align the support column assembly (A+D) with the pre-drilled holes on the underside of the tabletop. Secure using six M6x12mm screws (F) and one washer (H).

Step 3: Assemble the Base Frame

Connect the two base frame pieces (C) using the provided fasteners (M) and wheels (L). Insert the wheels into the designated slots on the base frame and secure them with fasteners (M). The Allen wrench (K) may be used for tightening.

Step 4: Attach Base Frame to Support Column

Invert the assembled base frame (C). Align its central mounting point with the bottom of the support column (A). Secure using four M6x45mm screws (G) and one washer (H).

Operation

Weight Limit: The maximum safe loading weight for the tabletop is 40 lbs (approximately 18.14 kg).

Height Adjustment:

To Raise: Lift the adjustment paddle located on the side of the support column. Guide the tabletop to the desired height.

To Lower: Lift the adjustment paddle and simultaneously press down on the tabletop to lower it to the desired height.

⚠️ Note: It is recommended not to exceed 40 lbs on the desktop to allow for easy lifting.

Product Parameters

Import and Representation Information:

Manufacturer/Origin: Made In China

Original Address: Baoshanqu Shuangchenglu 803long 11hao 1602A-1609shi Shanghai

Imported to AUS: SIHAO PTY LTD, 1 ROKEVA STREET EASTWOOD NSW 2122 Australia

Imported to USA: Sanven Technology Ltd. Suite 250, 9166 Anaheim Place, Rancho Cucamonga, CA 91730

EC REP: SHUNSHUN GmbH, Römeräcker 9 Z2021,76351 Linkenheim-Hochstetten, Germany

UK REP: Pooledas Group Ltd, Unit 5 Albert Edward House, The Pavilions Preston, United Kingdom