VEVOR Lifting Flat Table User Manual

Technical Support and E-Warranty Certificate https://www.vevor.com/support

ASSEMBLY PRECAUTIONS

Assemble only according to these instructions. Improper assembly can create hazards.
Wear ANSI-approved safety goggles and heavy-duty work gloves during assembly.
Keep the assembly area clean and well-lit.
Keep bystanders out of the area during assembly.
Do not assemble when tired or when under the influence of alcohol, drugs, or medication.
The product capabilities apply to properly and completely assembled products only.
Assemble on a flat, level, hard, and smooth surface capable of safely supporting the Lifting Flat Table.
For additional information regarding the parts listed in the following pages, please refer to the Assembly Diagram of this manual. Unwrap and separate all parts on a clear work area.

USE PRECAUTIONS

TO PREVENT SERIOUS INJURY AND DEATH FROM TIPPING:

This product is not a toy. Do not allow children to play with or approach this item.
Use as intended only. Do not sit or stand on the table.
Inspect before every use. Do not use it if parts are loose or damaged. Use only on flat, level, and hard surfaces.

TECHNICAL SPECIFICATIONS

Model	ZWE-DDJ-SS-01 ZWE-DDJ-SS-02	ZWE-DDJ-SS-03 ZWE-DDJ-SS-04	ZWE-DDJ-SS-05 ZWE-DDJ-SS-06	ZWE-DDJ-SS-07 ZWE-DDJ-SS-08
Adapter Rating(s)	100-240V~, 50/60Hz, 1.5A
Main Material	Steel + Board
Color	Brown + Black
Product Dimensions (LxWxH)	1200 x 600 x 1145 mm	1200 x 800 x 1145 mm	1400 x 600 x 1145 mm	1400 x 700 x 1145 mm
Packing Size (LxWxH)	1285 x 380 x 120 mm	1285 x 480 x 120 mm	1485 x 380 x 120 mm	1485 x 430 x 120 mm
Net Weight (kg)	21.8	24.4	23.2	25.2
Gross Weight (kg)	23.6	26.5	25.2	27.4

PACKAGE CONTENTS

A x2
B x1 (Leg B)
C x1
D x2
E x2
F x1
G x1
H x1
I x1
J x3
K x4
L x1
M x1
N x38 (M6*13)
P x2 (M4*40)
Q x8 (M6*35)
R x1
S x1
T x4
U x1
V x2 (ST4*12)
W x4

ASSEMBLY STEPS

STEP 1 Foot installation

Attach component A to component B using screws Q (M6*35) x8 and component W x4.

STEP 2 Motor installation

First, insert the motor (I) from the end of the hexagonal rod (H) without a bump to the other end with a bump.
Then, insert the convex end of the motor into leg B together with the motor. Tighten the motor on leg B with the screws P (M4*40) x2.

STEP 3 Drive rod installation

After completing the previous step, insert leg C into the hex stick (H). If the holes are misaligned, hold the motor by hand and adjust the hex rod to rotate slightly so that the hex rod can be inserted into leg C.

STEP 4 Beam installation

Attach component D to components B and C using screws N (M6*13) x12.

STEP 5 Side wing installation

Attach component E to the structure using screws N (M6*13) x4.

STEP 6 Panel splicing (1)

Join panels F and G using connectors K x4.

STEP 6 Panel splicing (2)

Secure the spliced panels F and G using brackets J x3 and screws N (M6*13) x12.

STEP 7 Panel installation

Attach the assembled panels to the frame using screws R x1 and N (M6*13) x8.

STEP 8 Accessories installation

Install accessories L x1, V x2 (ST4*12), O x2 (M6*13), and N x2 (M6*13).

STEP 9 Line connection

Connect the lines from component L to component M as shown in the diagram.

Height Adjustment Controller Operation

LED Display

Press any key once to wake up the LED display.

UP Key

Press and hold the UP key to raise the desk.

Down Key

Press and hold the DOWN key to lower the desk.

Memory Key

Memory Key 1, Memory Key 2, Memory Key 3

You must complete the Initialization Process to reset your desk before using it for the first time.

Detailed introduction of key functions

Reset

After running to the lowest height position, press and hold for 7 seconds. When the LED screen "rst" and "E-1" flash alternately, release the ↓ key, and press and hold the key again. After the desktop runs down to the lowest mechanical zero point, go back 5mm, the LED screen displays the lowest height value, and the reset is completed.

Set memory height + ①/②/③

Press the S key once, and the height value will start flashing. At this time, press the 1, 2, and 3 keys to save the current height to the corresponding position.

Execute memory height ① ② ③

In normal state, press the number key to call up its corresponding height, and the lifting table will automatically run to the corresponding position.

Lock key S

Press and hold the S key for 3 seconds. When the LED screen displays "SET", learn to open the S key. Press the number key 3 to enter the lock screen state. At this time, the LED screen flashes and displays "OFF". When the screen is locked, press and hold the S key for 3s, and the LED screen displays the height value. At this time, release the S key to complete the unlocking.

Restore factory settings S

Press and hold the S key for 9 seconds, release the S key when the LED screen displays "FAC", and operate the S key again to restore the factory settings.

Error Code Instructions

Error Code	Reason	Solution
Err	Err is displayed when the communication line sequence between the manual controller and the control box is wrong	/
E-1	When the system does not save the current position, the LED screen flashes alternately to display "E-1"	Reset by pressing the long key until the LED screen displays the minimum height and the alarm is released
E-2	When the motor is locked, the LED displays E-2	/
E-5	When the motor appears: the connecting line is disconnected/loosened, the LED screen flashes alternately to display "E-5"	1. Check the connection lines between all motors and the controller to ensure that they are firm, and then reset by long pressing the down key until the LED screen displays the minimum height, and remove the alarm
ovr	When the load exceeds the set value, the LED screen flashes to display ovr. At this time, it is necessary to remove the weight of the desktop and power on the controller after powering off. This alarm can be relieved	1. Normal load shall be controlled below 120KG 2. When the current exceeds 4A, the overload protection function will be triggered
hot	When the internal temperature of the controller exceeds 60 ± 5 degrees, the LED displays hot	/
vol	When the input voltage of the controller exceeds 34V, the LED displays vol	1. When the voltage exceeds 32V, the controller is powered off and the LED screen is black; 2. When the voltage drops to 32V, the system will automatically reply and LDE will display the real-time height
hot	After the motor runs continuously for 5min, the LED screen displays hot, and it can work normally after waiting for 10min	1. Uninterrupted operation means that the operation interval is within 3s 2. This alarm can also be removed when the control system is powered on again
E-3	During the operation, when suddenly blocked, the LED screen flashes "E-3", stops the action and runs 30mm in the opposite direction, then the LED screen displays the real-time height	It shall be ensured that the table will not vibrate significantly, bump into obstacles or tilt during operation

COMPLETION

The assembly is now complete.

Address: Baoshanqu Shuangchenglu 803long 11hao 1602A-1609shi Shanghai
Imported to USA: VEVOR STORE INC, 9448 RINCHMOND PL #E RANCHO CUCAMONGA, California, 91730 United States of America
SHUNSHUN GmbH Römeräcker 9 Z2021,76351 Linkenheim-Hochstetten, Germany
Pooledas Group Ltd Unit 5 Albert Edward House, The Pavilions Preston, United Kingdom

	VEVOR Lifting Flat Table User Manual - Assembly and Operation Guide This user manual provides detailed instructions for assembling and operating the VEVOR Lifting Flat Table (Models ZWE-DDJ-SS-09, ZWE-DDJ-SS-10). It includes technical specifications, package contents, step-by-step assembly, controller functions, and troubleshooting error codes.
	VEVOR Fabric Drawer Dresser User Manual - Model ZWE-BC-SS-03 Comprehensive user manual for the VEVOR Fabric Drawer Dresser (Model ZWE-BC-SS-03), including safety instructions, parts list, assembly steps, and product parameters. Learn how to safely assemble and use your new dresser.
	VEVOR CPU Cooler User's Guide - YC-01-SS-002, YC-01-SS-001 User's guide for VEVOR CPU Coolers, models YC-01-SS-002 and YC-01-SS-001. Includes installation instructions, parameters, and accessory list.
	VEVOR Car Basket TX-SS-01 TX-SS-02 User Manual and Warranty Comprehensive guide for the VEVOR Car Basket (Models TX-SS-01, TX-SS-02), covering installation, operation safety, parts list, cleaning, and manufacturer details. Find technical support and warranty information.
	VEVOR Seat Cushion SS-1/SS-2: User Manual, Features, and Care Guide Comprehensive guide for the VEVOR Seat Cushion (Models SS-1/SS-2). Learn about its premium memory foam, ergonomic design, non-slip features, material safety, cleaning instructions, and applicable uses for office, home, travel, and wheelchairs.
	VEVOR CPU Cooler User's Guide (Models YC-01-SS-004, YC-01-SS-003) Comprehensive user's guide for VEVOR CPU Coolers, models YC-01-SS-004 and YC-01-SS-003. Includes installation instructions, parameters, and accessory list for optimal PC cooling.
	VEVOR SS-602 Reception Desk User Manual and Assembly Guide This user manual provides detailed instructions for assembling and using the VEVOR SS-602 Reception Desk. It includes safety warnings, a comprehensive parts list, step-by-step assembly guidance, product specifications, and contact information for support.
	VEVOR Foldable Camping Table User Manual - Model AP-SS-004 Comprehensive user manual for the VEVOR Foldable Camping Table (Model AP-SS-004). Includes product parameters, assembly and use precautions, product features, installation guidance, and cleaning instructions.