VEVOR Desk Shelf

Product Overview

VEVOR is committed to providing tools with competitive prices. Expressions like "Save Half" or "Half Price" represent an estimate of savings compared to major top brands and do not cover all product categories. Please verify savings carefully when placing an order.

Safety Instructions

WARNING:

Read this material before using this product. Failure to do so may result in serious injury.

Assembly Precautions:

1. Assemble only according to these instructions. Improper assembly may create hazards.
2. Wear ANSI-approved safety goggles and heavy-duty work gloves during assembly.
3. Keep the assembly area clean and well-lit.
4. Keep bystanders out of the area during assembly.
5. Do not assemble if tired or when under the influence of alcohol, drugs, or medication.
6. The product capabilities apply to properly and completely assembled products only.
7. Assemble on a flat, level, hard, and smooth surface capable of safely supporting the Desk Shelf.
8. If possible, use power tools to make assembly easier.
9. For additional information regarding the parts listed in the following pages, please refer to the Assembly Diagram of this manual. Unwrap and separate all parts in a clean work area.

Use Precautions:

1. Do not exceed specified weight capacities.
2. Use only on a flat, level, hard, and smooth surface that can safely support a fully loaded Desk Shelf.
3. Use as intended only.
4. Inspect before every use; do not use if parts are loose or damaged.

SAVE THIS MANUAL

Parts List

The following parts are included in the package:

• [Part 1]: Top panel
• [Part 2]: Left side panel
• [Part 3]: Right side panel
• [Part 4]: Vertical divider
• [Part 5]: Shelf
• [Part 6]: Shelf
• [Part 7]: Back panel
• [Part 8]: Side panel
• [Part 9]: Side panel
• [Part 10]: Base panel
• [Part 11]: Drawer box (x2)
• [Part 12]: Support bar
• [Part 13]: Back panel
• [Part 14]: Drawer front

Hardware includes:

• [Hardware A]: Ø6x32mm (x22+1)
• [Hardware B]: Ø15x9.5 (x22+1)
• [Hardware C]: Ø8x30 (x18+1)
• [Hardware D]: Ø5 (x8+1)
• [Hardware E]: Ø4x35mm (x12)
• [Hardware F]: M4x8 (x2)
• [Hardware G]: M3x14mm (x10)
• [Hardware H]: 12*30 (x8)
• [Hardware I]: Ø20 (x22)
• [Hardware J]: M6x30 (x2)

Assembly Steps

Step 1

Attach part 10 (base panel) to part 1 (top panel) using four pieces of hardware A (Ø6x32mm). Rotate the assembly 180 degrees.

Step 2

Attach two pieces of hardware E (Ø4x35mm) to part 10. Then, attach part 8 (side panel) to the side of part 10 using two pieces of hardware E (Ø4x35mm).

Step 3

Connect part 8, part 9 (side panel), and part 10 (base panel) using two pieces of hardware C (Ø8x30) and two pieces of hardware B (Ø15x9.5).

Step 4

Attach part 7 (back panel) to the base assembly (part 10) using two pieces of hardware A (Ø6x32mm).

Step 5

Connect part 9 (side panel) and part 10 (base panel) to part 7 (back panel) using two pieces of hardware C (Ø8x30) and two pieces of hardware B (Ø15x9.5).

Step 6

Slide part 14 (drawer front) into the front of the assembled structure.

Step 7

Attach part 2 (left side panel) to the base assembly using four pieces of hardware A (Ø6x32mm).

Step 8

Connect part 2 (left side panel) to part 7 (back panel), part 9 (side panel), and part 10 (base panel) using four pieces of hardware C (Ø8x30) and four pieces of hardware B (Ø15x9.5).

Step 9

Attach part 2 (left side panel) to the structure using four pieces of hardware E (Ø4x35mm).

Step 10

Attach part 4 (vertical divider) to part 7 (back panel) using one piece of hardware C (Ø8x30) and two pieces of hardware E (Ø4x35mm).

Step 11

Attach part 5 (shelf) to part 7 (back panel) using one piece of hardware C (Ø8x30) and two pieces of hardware E (Ø4x35mm).

Step 12

Attach support bar 12 to the base assembly (part 10) using two pieces of hardware B (Ø15x9.5).

Step 13

Attach part 3 (right side panel) to the base assembly using four pieces of hardware A (Ø6x32mm).

Step 14

Connect part 3 (right side panel) to part 7 (back panel), part 5 (shelf), and support bar 12 using four pieces of hardware B (Ø15x9.5) and two pieces of hardware C (Ø8x30).

Step 15

Secure the structure by attaching eight pieces of hardware H (12*30) to the side panels.

Step 16

The main structure is now assembled.

Step 17

Place part 13 (back panel) on top of the assembled unit, aligning it with the structure. Insert eight pieces of hardware A (Ø6x32mm) from the top.

Step 18

Attach part 2 (left side panel) to the top panel (part 1) using eight pieces of hardware A (Ø6x32mm).

Step 19

Connect part 1 (top panel) to the main structure using six pieces of hardware C (Ø8x30) and eight pieces of hardware B (Ø15x9.5).

Step 20

Secure the shelves and back panels using ten pieces of hardware G (M3x14mm).

Step 21

Secure the structure using eight pieces of hardware D (Ø5) and the provided support H (a cylindrical peg with a cap).

Step 22

The desk shelf is taking shape. Part 6 (shelf) is shown being attached.

Step 23

Attach the drawer components using twenty-two pieces of hardware I (Ø20) and two pieces of hardware B (Ø15x9.5).

Step 24

Assemble the drawer boxes (Part 11) using two pieces of hardware F (M4x8) for each drawer.

Step 25

Insert the assembled drawer boxes into the desk shelf unit.

Step 26

Secure the desk shelf to the wall using two pieces of hardware J (M6x30) and two pieces of hardware (Ø4x35mm and Ø3x12mm).

Product Parameters

* Products such as specifications, appearance, and design are subject to modification without prior notice.

Manufacturer and Importer Information

Manufacturer: Shanghaimuxinmuyeyouxiangongsi

Address: Shuangchenglu 803nong11hao1602A-1609shi, baoshanqu, shanghai 200000 CN.

Imported to AUS: SIHAO PTY LTD. 1 ROKEVA STREETEASTWOOD NSW 2122 Australia

Imported to USA: Sanven Technology Ltd. Suite 250, 9166 Anaheim Place, Rancho Cucamonga, CA 91730

EU Representative: E-CrossStu GmbH, Mainzer Landstr.69, 60329 Frankfurt am Main.

UK Representative: YH CONSULTING LIMITED. C/O YH Consulting Limited Office 147, Centurion House, London Road, Staines-upon-Thames, Surrey, TW18 4AX