VEVOR Fabric Drawer Dresser User Manual

Model: ZWE-BC-SS-03

Technical Support and E-Warranty Certificate

www.vevor.com/support

VEVOR is committed to providing tools with competitive prices. Phrases like "Save Half" or "Half Price" represent estimated savings compared to major top brands and may not apply to all product categories. Please verify savings carefully when placing an order.

Safety Instructions

⚠️ WARNING: Read this material before using this product. Failure to do so can result in serious injury.

Assembly Precautions

1. Assemble only according to these instructions. Improper assembly can create hazards.
2. Wear ANSI-approved safety goggles and heavy-duty work gloves during assembly.
3. Keep the assembly area clean and well-lit.
4. Keep bystanders out of the area during assembly.
5. Do not assemble if tired or under the influence of alcohol, drugs, or medication.
6. Product capabilities apply only to properly and completely assembled products.
7. Assemble on a flat, level, hard, and smooth surface capable of safely supporting the Fabric Drawer Dresser.
8. For additional information regarding parts, refer to the Assembly Diagram. Unwrap and separate all parts in a clean work area.

Use Precautions

1. DO NOT SIT OR STAND ON THIS ITEM.
2. This product is not a toy. Do not allow children to play with or near this item.
3. Do not exceed specified weight capacities.
4. Use only on a flat, level, hard, and smooth surface that can safely support a fully loaded Fabric Drawer Dresser.
5. Use as intended only.
6. Inspect before every use; do not use if parts are loose or damaged.

SAVE THIS MANUAL

Exploded Drawing

⚠️ WARNING:

1. Plates and screws may not be common; please read the manual carefully before installation and distinguish each plate and screw.

2. Do not tighten screws too tightly before installation; tighten all screws after installation.

Diagram Description:

The diagram shows the components of the Fabric Drawer Dresser laid out separately, with numbers indicating each part. The main frame components (side panels, back panels, support rods) are shown, along with drawer boxes and hardware. The overall structure is a rectangular dresser with multiple drawers.

Numbered Parts:

• 1: Top Panel
• 2: Left Side Frame
• 3: Right Side Frame
• 4: Middle Support Frame
• 5: Horizontal Support Rods
• 6: Long Rods
• 7: Short Rods
• 8: Drawer Support Rods
• 9: Drawer Box

Parts List

Assembly Steps

Step 1

Attach the Left Side Frame (2), Right Side Frame (3), and Middle Support Frame (4) using Long Rods (6) and Screws (A). Ensure the frames are aligned correctly. Use 6 Screws (A) for this step.

Step 2

Connect the assembled frame structure using Horizontal Support Rods (5) and Short Rods (7). Attach these rods to the side and middle frames. Note: Ensure the side with the large hole faces downwards. Use 5 Screws (A) and 2 Screws (B) for this step.

Step 3

Attach the Top Panel (1) to the frame structure using Screws (A). Attach the Feet/Legs (F) to the bottom of the side frames using Screws (B). Use 4 Screws (A) for the top panel, 5 Feet/Legs (F), and 8 Screws (B) for the feet.

Step 4

Install the Drawer Support Rods (8) into the frame. Secure them using Screws (A), Screws (B), and Nuts (C). Use 6 Screws (A), 2 Screws (B), and 8 Nuts (C) for this step.

Step 5

Assemble the Drawer Boxes (9). Insert the drawer sides into the drawer front/back panels. Secure the drawer boxes using Screws (D) and attach the Drawer Handles (E). Use 12 Screws (D) and 6 Drawer Handles (E) for this step.

Step 6

Insert the assembled Drawer Boxes (9) into the dresser frame.

Step 7

Note:

1. Mark the desired location on the wall.
2. Use an electric drill to drill deep holes in the wall.
3. Tap part G (Anti-tip Kit) into the hole.

After cabinet assembly, install the anti-tip device on the back of the cabinet to avoid accidents. Install at a location based on your needs. The diagram shows how to attach the anti-tip straps (G) to the back of the dresser and the wall.

Product Parameters

Manufacturer and Importer Information

Manufacturer: Shanghaimuxinmuyeyouxiangongsi

Address: Shuangchenglu 803nong11hao1602A-1609shi, baoshanqu, shanghai 200000 CN.

Imported to AUS: SIHAO PTY LTD. 1 ROKEVA STREETEASTWOOD NSW 2122 Australia

Imported to USA: Sanven Technology Ltd. Suite 250, 9166 Anaheim Place, Rancho Cucamonga, CA 91730

EC Representative: E-CrossStu GmbH, Mainzer Landstr.69, 60329 Frankfurt am Main.

UK Representative: YH CONSULTING LIMITED. C/O YH Consulting Limited Office 147, Centurion House, London Road, Staines-upon-Thames, Surrey, TW18 4AX