K-O2-S5
Oxygen Sensor/Mai watsawa da 
Biyu-Stage Alarm Controller 
Manual mai amfani

BAYANIN BAYANIN BAYANIN KYAUTATA
Wannan Littafin ya ƙunshi Kele K-O2-xx iskar oxygen da dangin firikwensin. Iyalin sun ƙunshi nau'ikan nau'ikan 4 tare da fasali gama gari da ayyuka, ana samun su a cikin salon shinge biyu da zaɓuɓɓukan rayuwa na firikwensin guda biyu kamar yadda aka nuna a Tebu 1.

Bayani	Kele Part Number
Rufe shinge tare da rayuwar firikwensin shekaru 5	K-O2-S5
Rufe shinge tare da rayuwar firikwensin shekaru 10	K-O2-S10
Mai kullewa, shinge mai shinge tare da rayuwar firikwensin shekaru 5	K-O2-H5
Mai kullewa, shinge mai shinge tare da rayuwar firikwensin shekaru 10	K-O2-H10

Tebur 1: K-O2 Lambobin Iyali  

Ana jigilar duk nau'ikan K-O2-xx tare da ko dai 5-shekara rayuwa (K-O2-x5) ko rayuwar shekaru 10 (K-O2-x10) masana'anta calibrated oxygen maida hankali module shigar. A ƙarshen rayuwar firikwensin wannan filogi, na'ura mai ƙima, sauƙi mai sauƙin maye gurbin filaye ana samun su daga Kele.

Bayani	Kele Part Number
Tsarin firikwensin maye gurbin na shekaru 5	KMOD-O2-25
Tsarin firikwensin maye gurbin na shekaru 10	KMOD-O2-50

Tebura 2: K-O2 Matsakaicin Matsakaicin Matsala na Iyali Lambobin Sashe  

Kit ɗin daidaitawa mai ɗauke da na'urorin haɗi da ake buƙata don daidaita kowane ɗayan firikwensin dangin K-O2 yana samuwa daga Kele ƙarƙashin lambar ɓangaren UCK-1.

BAYANI

Makanikai
Ginin Ginin Chassis	Ƙarfin masana'antu, 18 Ga. Grey foda mai rufi karfe. Akwai salon murfi mai kulle-kulle ko ƙulli.
Nauyi	2.0 lbs
Yanayin Aiki	4 zuwa 40 ° C
Humidity Mai Aiki	15 - 90% RH, mara sanyaya
Ajiya Zazzabi	-20 zuwa 20 ° C (don rage lalacewar firikwensin)
Girman Hali (H x W x D)	K-O2-Hx: 6.4" x 5.9" x 2.4" (163.5 x 150.8 x 60.7 mm) K-O2-Sx: 6.3" x 5.8" x 2.1" (160.0 x 147.3 x 52.0 mm)
Sensor Vents	Iskar yanayi ta hanyar 18, 0.1" (2.54 mm) diamita
Alamun Waje	LED mai launi uku yana nuna matsayin aiki na firikwensin.
Kashewa	4 ciniki ½" knockouts (1 kowane gefe)

Table 3: Ƙayyadaddun Makanikai 

Lantarki
Ƙarfin Aiki Voltage	14 - 30 VAC (RMS) ko DC Keɓaɓɓen wutar lantarki; daban daban ba a buƙata.
Amfanin Wuta	<5W
Sarrafa Relays	2 raba layin SPDT-voltage-mai iya relays don faɗakarwa/shakata da ƙararrawa. UL-rated: 10 Amps max a 120/277 VAC ko 30 VDC. (E43203)
Fitar Rahoto Tattaunawa	Warewa, fitarwa na madauki na yanzu 4-20mA. 4 mA fitarwa => 0 % maida hankali. 20 mA => 25% Matsakaicin juriya na madauki: 510Ω
Karewa	Tashoshin dunƙule masu toshewa don amfani tare da 12 AWG ko sirara waya

Tebur 4: Bayanin Wutar Lantarki

Sensor Oxygen (O2)
Nau'in Sensor	Galvanic cell
Ma'auni Range	0 - 25% (ta girma)
Analog Output Range	4-20mA (daidai da 0 zuwa 25%)
Daidaito	± 0.3% O₂ (na al'ada bayan daidaitawa)
Kayyade tazara	Watanni 6 (don kiyaye ƙayyadaddun daidaito)
Sensor Rayuwa	K-O2-x5: shekaru 5 (na al'ada) K-O2-x10: shekaru 10 (na al'ada)
Filayen Filaye Mai Mayar da Hankali Na Shawarar	KMOD-O2-25 (shekaru 5) ko KMOD-O2-50 (shekaru 10)
Kit ɗin Calibration	UCK-1 kit
Calibration gas	Tsayi (20.9% oxygen, nitrogen ma'auni): Kele PN: GAS-O2-20.9 Sifili (100% nitrogen) Kele PN: GAS-N2

Table 5: Oxygen Sensor Specificities  

SHIGA INJI

Model K-O2 yana samuwa a cikin nau'i biyu na ƙarfin masana'antu, ma'auni 18, launin toka, shingen karfe mai rufi. Ana nuna nau'in murfin kulle-kulle, nau'in murfin hinged a cikin Hoto 1 kuma ana nuna nau'in murfin murfi mai cirewa a cikin hoto na 2. Dukkanin na'urorin lantarki suna haɗe zuwa murfin gaba. Akwai cinikin ½” ƙwanƙwasa magudanar ruwa a kowane bangare don haɗin wutar lantarki. A cikin yiwuwar damp wuraren da ya kamata a yi amfani da ƙwanƙwasa a ƙasan harka don rage yiwuwar shigar ruwa. KAR KA YI AMFANI DA RUMOMIN FUSKA DON SHIGA WAYAR.

1. An ƙera wannan rukunin don hawa zuwa wani tsayayyen ƙasa mara jijjiga kusa da tsakiyar yankin don a kula da shi kusan ƙafa 5 sama da ƙasa.
2. Ya kamata a kasance a inda akwai iskar iska kyauta - kauce wa sasanninta ko wuraren zama.
3. Fitowar iska a gefen shingen kada ta kasance kusa da ƙafa 1 daga bangon madaidaici mafi kusa kuma kada a toshe shi ko fenti.
4. Ana iya hawa
   1. A tsaye tare da matsayi LED a cikin ƙananan hagu ko ƙananan dama.
   2. A tsaye a cikin kowace fuskantarwa.
5. Ana yin ramukan hawa don sukurori na bango kai tsaye don farfajiyar da aka ci karo da su. (Ba a samar da screws ba) ko canza tazarar akwatin.

2.1 MULKI 

Salon Harka	Mtg rami diamita	Nisa daga tsakiya
		A kwance	A tsaye
K-O2-Hx (Hinged)	5/16" (7.94 mm)	1.25" (31.75 mm)	1.50" (38.10 mm)
K-O2-Sx (Screw down)	9/32" (7.14 mm)	1.50" (38.10 mm)	1.50" (38.10 mm)

KYAUTATA WUTAN LANTARKI

Ba a sanye take da mai sarrafa wutar lantarki ba; yana aiki a duk lokacin da aka yi amfani da isasshiyar wutar lantarki a tashoshin shigar da wutar lantarki.
Dukkan hanyoyin haɗin lantarki zuwa mai sarrafawa ana yin su ta tashoshi masu dunƙulewa waɗanda za a iya cire su don sauƙin saukowa na wayoyi. Wurin mai sarrafawa yana ƙunshe da ƙwanƙwasa ƙwanƙwasa a kowane bangare don sassauci yayin shigarwa; duba Hoto na 1 da Hoto 2 don cikakkun bayanai da ma'auni na ma'auni.

3.1 ANALOG FITAR DA HANNU
Ana ba da rahoton karatun firikwensin a haɗin haɗin kai na analog na 420mA na mai sarrafawa. A halin yanzu yana gudana daga tashar '+' kuma yana komawa zuwa tashar '-'.

Ana samar da firikwensin iskar oxygen a tashar da aka haskaka a cikin Hoto 3. Haɗin fitarwa na analog yana da polarity kamar yadda aka lakafta akan siliki mai sarrafawa: dole ne a kula don tabbatar da haɗin kai mai kyau. Don waya da haɗin fitarwa na analog:

1. Ƙaddamar da mai sarrafawa, ana iya yin wannan ta hanyar cire haɗin wutar lantarki (duba hoto 6).
2. Cire tashar fitarwa ta analog mai alamar O1.
3. Haɗa siginar siginar, kula da hankali ga polarity.
4. Toshe tashar fitarwa ta analog ɗin baya cikin mai sarrafawa.

3.2 HANYAR SAUKARWA
Mai sarrafawa yana da biyu, 10 Amp, 120/277 VAC UL-rated, SPDT bushe lamba relay fitarwa haši (wanda aka nuna a Figure 4) wanda zai iya kai tsaye sarrafa lodi har zuwa 10 Ampta hanyar tashar budewa ta al'ada.
Haɗin haɗin kai yana da masu haɗa dunƙule tasha uku waɗanda ke ba da damar haɗa na'urori zuwa mai sarrafawa a cikin ko dai-buɗewa (NO) ko na-rufe (NC). Ana kunna waɗannan abubuwan fitowar lokacin da iskar oxygen na yanayi ya faɗi ƙasa da saitunan masu sarrafawa (koma zuwa Sashe na 4.2 don ƙarin bayani).

A cikin NO Kanfigareshan, voltage haɗe zuwa tashar NO zai kasance a tashar COM kawai lokacin da aka kunna fitarwar relay.
A cikin Kanfigareshan NC, voltage haɗe zuwa tashar NC zai kasance a tashar COM kawai yayin da aka kashe fitarwar relay: vol.tagAna cire e haɗe zuwa tashar NC lokacin da aka kunna fitarwar relay.
ExampAna ba da zane-zanen wayoyi don haɗin kai tsaye a hoto na 5. Don yin waya da abubuwan faɗakarwa/shakata da ƙararrawa:

1. Ƙayyade idan na'urar tana haɗe zuwa fitowar gudun ba da sanda ya kamata a haɗa ta cikin NO ko NC daidaitawa.
2. Cire na'ura mai ba da hanya tsakanin hanyoyin sadarwa.
3. Haɗa kayan aiki voltage don na'urar da ke haɗe zuwa fitarwar mai sarrafawa zuwa ko dai wurin NO ko NC na tashar screw (duba Hoto 4).
4. Waya shigar da wutar lantarki na na'urar da ke haɗe zuwa fitarwar mai sarrafawa zuwa wurin COM na tasha.
5. Toshe tashar fitarwa ta relay zuwa madaidaicin wurin akan allon sarrafawa.

3.3 HADA WUTA
K-O2 yana da cikakken keɓantacce, shigar da wutar lantarki mara ƙarfi; ko dai AC ko DC ikon aiki za a iya haɗa su a ko dai polarity. Raka'o'in K-O2 da yawa suna iya aiki akan taswira iri ɗaya (har zuwa iyakar nauyinta) koda lokacin da ba'a haɗa su da madaidaicin inganci / mara kyau ko zafi / gama gari.
Haɗin wutar lantarki zuwa mai sarrafawa ana yin shi a mahaɗin dunƙule tasha biyu wanda yake a gefen dama na allo (wanda aka haskaka a hoto 6). Ƙarfin mai sarrafawa zai iya zama ko dai AC ko DC voltage; DC voltage za a iya haɗa shi a kowane nau'i na polarity (duba Sashe 1.0 don ƙarin cikakkun bayanai). Zuwa wutar waya:

1. Bude shingen mai sarrafawa kuma cire toshe tasha mai lamba POWER akan allon sarrafawa.
2. Haɗa wayoyi masu ƙarfi zuwa tashar screw tare da tabbatar da haɗin gwiwa ya kullu.
3. Toshe tashar dunƙule ta koma cikin ma'ajin POWER a kan allon sarrafawa: wannan zai sa mai sarrafawa ya kunna wuta kuma ya fara aiki.

Ana ba da shawarar cewa an yi duk haɗin haɗin waya kafin samar da wuta ga mai sarrafawa.

BAYANIN AIKI

K-O2 shine biyu-stage iskar iska da mai kula da ƙararrawa wanda ke jin ƙwayar iskar oxygen a cikin sararin sararin samaniya da ke kewaye da shi kuma yana aiki da rufewar Gargaɗi/Na'ura mai ɗaukar iska wanda za'a iya amfani da shi don sarrafa magoya bayan iska lokacin da aka gano raguwar matakan oxygen. Idan maida hankali na iskar oxygen ya kusanci matakan da ba su da aminci, ana yin aiki da rufe lamba na biyu; yawanci don kunna ƙararrawa.
Na'urar firikwensin iskar gas ɗin ƙirar ƙira ce wacce za'a iya maye gurbinta da ƙaramin ƙoƙari lokacin da ta kai ƙarshen rayuwa (EOL) yayin barin babban sarrafawa da aka ɗora da waya (duba Sashe na 7.1).
Murfin gaba yana da alamar matsayi na LED wanda ke haskakawa cikin launuka daban-daban don nuna al'ada (kore), Gargadi/Hanyar iska (rawaya), da yanayin ƙararrawa (ja). Jajayen kyaftawa yana nuna cewa firikwensin baya aiki. Yayin da LED ke kyalli ja, fitowar analog tana isar da 4 mA don nuna kuskuren. Ana ba da rahoton tattarawar iskar oxygen a cikin iskar yanayi a fitowar madauki na analog na mai sarrafawa kamar kashi ta ƙara. Fitowar analog daga 4 zuwa 20mA (koma zuwa Table 4 da Table 5).

Yanayin LED Launi	Bayanin Matsayin Aiki
	Hankali yana sama da iyakar faɗakarwa/shafi. Babu fitowar gudun ba da sanda da ke aiki.
	Tattaunawa yana ƙasa da madaidaicin faɗakarwa/shafi kuma sama da ƙofar ƙararrawa. Gargadi/iska mai isar da sako yana aiki.
	Tattaunawa yana ƙasa da iyakar ƙararrawa. Dukansu faɗakarwa/shafi da faɗakarwa suna aiki.
	Gargadi Karshen Rayuwa. Firikwensin ya kai ƙarshen ƙimar sabis ɗin sa kuma yakamata a maye gurbinsa. Relays da abubuwan analog suna ci gaba da aiki akai-akai.
	Sensor ya ƙare. Gargadi/sake faɗakarwa yana aiki kuma fitarwar analog shine 4mA. ( koma zuwa Sashe na 7)

Tebura 7: Matsayin Matsayin Fuskar Fuskar LED Alamomi yayin Aiki na Al'ada. 

4.1 HANYA NA MUSAMMAN
K-O2 yana aiki ta hanyoyi da yawa kamar yadda aka nuna a Table 9. Tebura 9: K-O2 Yanayin Aiki
Aiki na yau da kullun kamar yadda aka bayyana a sama. Yayin yanayin jiran aiki, firikwensin yana daidaitawa kuma ana gudanar da fitowar analog a 20mA.
A lokacin gyare-gyaren lokaci, ana kwatanta halayen firikwensin da hankalinsa a farkon daidaitawar masana'anta. Idan hankalinsa ya faɗi ƙasa da ƙayyadaddun masana'anta K-O2 yana shiga yanayin Ƙarfafawar Sensor tare da fitowar analog ɗin da aka gudanar a 4 mA kuma kawai an kunna relay na Gargaɗi/Hanyoyin iska.

Yanayin	LED murfin gaban	Analog Fitar	An kunna Relays	Sharhi
Na al'ada	Kore mai ƙarfi, Yellow ko Ja	4-20 mA	Ya dogara da maida hankali	A lokacin aiki na al'ada
Tsaya tukuna	Daban-daban	20 mA	BABU	A lokacin tazarar farawa ko kowane lokaci yayin calibration
EOL gargadi	Rawaya mai Kiftawar hankali	4-20 mA	Ya dogara da maida hankali	Sensor yana kusa da ƙarshen ƙimar sabis ɗin sa. Relays da fitarwa na analog suna aiki kullum.
Sensor ya ƙare	Slow Blinking Ja	4 mA	Gargadi / Samun iska	Bayan daidaita na'urar firikwensin da ya ƙare. Na'urar firikwensin baya aiki.

Tebur 9: K-O2 Hanyoyin Aiki 

	O₂
Ƙaddamarwa na OSHA ta Tarayya (PEL).	19.50%

4.2 GARGAƊI / HANKALI DA SHARUDANAR ARArrawa
Biyu, 10 Amp, 120/277 VAC rated, busasshen lamba, SPDT relays kunna yayin faɗakarwa / iska da yanayin ƙararrawa: koma zuwa Sashe 3.2 don bayanin waya.
Lokacin da yawan iskar oxygen ya faɗi ƙasa da ƙayyadaddun gargaɗinsa/ƙofar samun iska, ana kunna fitarwar WARNING/VENTILATION. Lokacin da maida hankali ya faɗi ƙasa da ƙofar ƙararrawa, ana kuma kunna relay na ALARM na mai sarrafawa. Lokacin da oxygen maida hankali
ya tashi sama da madaidaicin ƙararrawa, an kashe relay na ALARM; lokacin da ya tashi sama da bakin kofa na iskar shaka shima ana kashe shi.

4.3 KASANCEWAR MATSALAR HANKALI DA ARARAWA
An nuna nau'i-nau'i-nau'i-nau'i-nau'i-nau'i-nau'i-nau'i-nau'i-nau'i na ma'aikata da matakan ƙararrawa ana nuna su a cikin Tebur 8. Kowane saiti yana ƙayyade duka gargaɗin mai sarrafawa / iska da mashigin ƙararrawa.
Ana zaɓar ƙimar ƙima mai aiki ta hanyar saita maɓallan DIP guda biyu akan babban allo (duba Hoto 8) kamar yadda aka nuna a shafi na farko na Tebura 8 don saitin da ake so.

4.4 LABARI DA DUMI-DUMINSU
A cikin yanayin al'ada, ana ba da rahoton karatun tattarawar iskar oxygen daga firikwensin ta hanyar fitar da madauki na 4-20mA na mai sarrafawa. Ana nuna wurin mai haɗa kayan fitarwa a hoto na 6. Ƙimar fitarwa yana kamar yadda aka nuna a Table 5.

ENSOR CALIBRATION

Hankalin firikwensin oxygen galvanic da aka yi amfani da shi akan jerin K-O2 yana raguwa yayin da firikwensin ya tsufa. A tsawon rayuwar firikwensin, daidaitonsa yana raguwa da kusan 30%. Ba tare da daidaitawa ba, firikwensin zai nuna kusan kashi 14.7% na iskar oxygen a cikin iska mai kyau bayan 5 (na K-O2-x5) ko 10 (na K-O2-x10) shekaru.
Mitar daidaitawa da ake buƙata ya dogara da daidaiton abin da ake buƙata na aikace-aikacen. Don kiyaye daidaito da aka ƙayyade a cikin Teburin 5 sama da cikakken kewayon aiki na jerin K-O2, ana ba da shawarar cikakken tazara na watanni 6. Daidaitawar shekara-shekara zai yawanci kiyaye daidaito tsakanin kusan 0.5% O2 (na K-O2-x5) da kusan 0.3% O2 ​​(na K-O2-x10).
Don ingantacciyar daidaito, cikakken tsarin daidaita matakan matakai biyu yana samar da na'urar firikwensin tare da iskar 'zero' mara oxygen, sannan ana buƙatar iskar 'span' 21%. Ana samar da maɓallan daidaitawa guda biyu (ZERO da SPAN) akan babban allo don fara kowane aikin daidaitawa kamar yadda aka nuna a hoto na 8.
Don aikace-aikace tsakanin 18% da 21% oxygen, daidaitawar tazara-kawai sau da yawa yakan isa kuma baya buƙatar iskar gas. Duk abin da ake buƙata shine tabbacin iska mai daɗi a kusa da firikwensin. Don daidaito a ƙananan kashi na oxygentage, gyare-gyaren sifili kafin a ba da shawarar daidaitawa.
Don aiwatar da daidaitawar tazarar iskar gas: Bi hanya a cikin sashe na 5.4, yin watsi da duk umarnin game da aikace-aikacen ko cire gas ɗin daidaitawa ko kayan aiki.
Za a yi gwajin 'sensor ɗin da ya ƙare' a ƙarshen gyare-gyaren lokaci. Idan hankalin firikwensin ya faɗi ƙasa da ƙayyadaddun ƙarshen rayuwa na masana'anta, K-O2 yana shiga yanayin Ƙarshen Sensor tare da murfin gaban LED a hankali yana kyalli. JAN, fitowar analog a madaidaicin 4 mA, kuma an kunna faɗakarwar faɗakarwa/iska. Na'urar firikwensin iskar oxygen baya aiki kuma dole ne a maye gurbinsa (Duba sashe na 6).
Matsayin tsarin daidaitawa ana nuna shi ta hanyar walƙiya na murfin murfin gaban LED kamar yadda aka nuna a ƙasa.

Koren Kiftawa	Nasara sampling. Jiran mai amfani ya tabbatar da cire iskar gas.
Ja mai kiftawa	Yunkurin daidaitawa bai yi nasara ba. Jiran mai amfani ya yarda tare da sake gwadawa ko fita.
Kore/Yellow	A lokacin daidaita yanayin yanayi bayan nasarar daidaitawa. Ana amfani da sabon daidaitawa.
Ja/Yellow	A lokacin daidaitattun yanayi bayan gazawar sampling. Tsohuwar daidaitawa ba ta canzawa.

Shafi na 10: Ma'anar Matsayin Samfuran Kiftawar LED yayin daidaitawa.

5.1 CALIBRATION GASES
Tsaftataccen iskar iskar nitrogen da madaidaicin cakuda oxygen na 20.9%, da ma'auni nitrogen (duba Table 11) ana buƙatar cikakken daidaita firikwensin oxygen don iyakar daidaito.
Kit ɗin daidaitawa wanda ya haɗa da duk kayan haɗin da ake buƙata (amma ba gas ɗin kanta ba) a cikin akwati mai dacewa yana samuwa daga Kele.com azaman lambar ɓangaren UCK-1. Ana yin odar gas ɗin daidaitawa daban ta amfani da sassan lambobi da aka nuna a Table 11.

Nau'in	Cakuda (ta girma)	Kele Part No.
Sifirin gas	Nitrogen mai tsabta	GAS-N2
Fadin gas	20.9% oxygen balance nitrogen	GAS-O2-20.9

Shafin 11: Gases Calibration da ake buƙata 

Duk na'urori masu auna firikwensin K-O2 sun haɗa da madaidaicin firikwensin oxygen firikwensin calibration da aka adana a cikin ƙananan kusurwar hagu na shinge kamar yadda aka nuna a cikin Hoto na 10. Ana ba da iskar gas ta hanyar mai hana kwararar tube-barb wanda ya dace da kunkuntar ƙarshen mashin cal a matsa lamba. da 10 psi.

5.2 CALIBRATION GAS HADIN
Ana nuna tsarin haɗin haɗin bututun iskar gas tsakanin mai tsarawa da hular daidaitawa a hoto na 9.
calibration gas wadata tiyo zuwa calibration cap, zame da bude karshen hula a kan hexagonal farin gas tashar jiragen ruwa a kan oxygen firikwensin. Tabbatar cewa hular ta rufe tashar gas gaba ɗaya; kada a sami wani farar nuni a kasan hular.
Lokacin da aka shirya don fara daidaitawa, daidaita mai sarrafa iskar gas ta yadda ma'aunin matsi ya karanta 10 psi.

5.3 TSARIN CALIBRATION ZERO
Don iyakar daidaiton da ke ƙasa da 18%, dole ne a yi tsarin daidaitawar sifili kafin daidaitawar Taɗi.
Ana nuna ci gaba da matsayi na tsarin daidaitawa ta launi da walƙiya na halin murfin gaban LED (duba Table 10).
Aiwatar da iskar iskar gas na nitrogen (sifili) zuwa firikwensin ta amfani da hular daidaitawa da aka haɗa. Tabbatar cewa gas yana gudana zuwa firikwensin, sannan danna ka riƙe maɓallin 'ZERO' (duba Hoto 8) na tsawon daƙiƙa 3 har sai murfin gaban LED ya fara kiftawa. YELU, yana nuna cewa gas sampling yana ci gaba.

1. Tabbatar cewa adaftar daidaitawa ta zauna daidai kuma iskar gas na ci gaba da gudana na mintuna 2 samptsawon lokaci.
2. A karshen sampA lokaci guda, matsayin firikwensin LED yana ƙiftawa GREEN idan sampling ya yi nasara ko RED idan ba haka ba.
3. A. Idan nasara (Green mai kyalli):
   Gas sampAn kammala ling cikin nasara. Kashe motsin gas ɗin calibration, cire hular calibration sannan latsa ka riƙe maɓallin 'ZERO' calibration har sai LED ya lumshe. GREEN/YELU wanda ke nuni da cewa an cire iskar gas ɗin, an yi amfani da madaidaicin kuma naúrar tana kan jiran aiki na tsawon mintuna biyu yayin da firikwensin ya sake daidaita yanayin yanayin kafin a fara aiki na yau da kullun. Daidaiton yana cika lokacin da halin LED ya dawo daidai GREEN.
   OR 
   B. Idan BA A yi nasara ba (Jan kyaftawa):
   Mafi kusantar dalilin sifili calibration sampRashin gazawar iskar iskar gas bai isa ba ko yawo a kusa da adaftar daidaitawa ya kasa nutsar da firikwensin gaba daya cikin nitrogen. Tabbatar cewa iskar gas ɗin har yanzu yana gudana akan ƙimar da ake buƙata (ma'aunin matsi yana karanta 10 psi) kuma adaftar daidaitawa tana cikin matsayi da kyau.
   Daidaiton sampAna iya sake kunna ling yayin da LED ke kiftawa JAN ta sake latsawa da riƙe maɓallin 'ZERO' har sai LED ɗin ya lumshe YELU, sai a koma mataki na 1 a sama.
   Don fita daga tsarin sifili na yau da kullun don kiyaye daidaitaccen daidaitawa na asali: kashe kwararar iskar gas ɗin kuma cire adaftar daidaitawa, sannan danna kuma saki maɓallin 'ZERO' da sauri. Halin LED zai lumshe ido JAN/YELOW wanda ke nuni da cewa an cire iskar gas ɗin, an ajiye ainihin daidaitawar kuma naúrar tana kan jiran aiki na tsawon mintuna biyu yayin da firikwensin ya sake daidaita yanayin yanayin kafin a fara aiki na yau da kullun. An dawo da daidaitaccen daidaitawar asali gaba ɗaya lokacin da matsayin LED ya dawo daidai GREEN.

5.4 TSARIN CALIBRATION SPAIN
Don mafi kyawun daidaito, tsarin daidaitawar sifili a cikin sashe na 5.2 yakamata a yi kafin daidaitawar Taƙaitawa. Yi watsi da matakai a cikin haske mai launin shuɗi mai haske idan kuna yin ƙarancin iskar gas.

Ana nuna ci gaba da matsayi na tsarin daidaitawa ta launi da walƙiya na halin murfin gaban LED (duba 10).

1. [Fara iskar gas ɗin da ke gudana,] danna ka riƙe maɓallin 'SPAN' (duba Hoto 8) na tsawon daƙiƙa 3 har sai yanayin LED ya fara kiftawa. YELU, yana nuna cewa gas sampling yana ci gaba.
2. [Tabbatar cewa adaftar daidaitawa ta rufe firikwensin gaba daya na tsawon mintuna 2ampzamani].
   A karshen sampA lokaci guda, matsayin firikwensin LED yana ƙiftawa GREEN idan sampling yayi nasara ko JAN in ba haka ba.
3. A. Idan nasara (blinking GREEN):
   A sampAn kammala ling cikin nasara. [Kashe kwararar iskar gas ɗin, cire adaftar daidaitawa sannan] latsa ka riƙe maɓallin 'SPAN' har sai LED ɗin ya lumshe. GREEN/YELU yana nuni da cewa [an cire iskar gas ɗin,] an yi amfani da sabon daidaitawa kuma sashin yana cikin jiran aiki na mintuna biyu yayin da firikwensin ya sake daidaita yanayin yanayin kafin a fara aiki na yau da kullun. Daidaiton yana cika lokacin da halin LED ya dawo daidai GREEN.
   OR
   3B. Idan BA a yi nasara ba (blinking JAN:
   Abubuwan da suka fi dacewa na span gas sampRashin gazawar sune:
    [Rashin isassun iskar gas ko yawo a kusa da adaftar daidaitawa baya nutsar da firikwensin gaba ɗaya a cikin iskar gas ɗin. Tabbatar cewa silinda mai daidaitawa bai ƙare ba kuma adaftar daidaitawa tana matsayi da kyau.]  Matsakaicin iskar oxygen a firikwensin ba shine tsakanin 20.8 da 21.0 bisa dari (ta girma).

Daidaiton sampAna iya sake kunna ling yayin da LED ke kiftawa JAN ta sake latsawa da riƙe maɓallin 'SPAN' har sai LED ɗin ya lumshe YELU, sai kaje mataki na 1 na sama.
Don fita tazarar gyare-gyaren da ke adana ainihin daidaitawar, latsa kuma da sauri saki maɓallin daidaitawa na 'SPAN'. Halin LED zai lumshe ido JAN/YELOW yana nuni da cewa an cire iskar gas ɗin, za a adana ainihin daidaitawar kuma naúrar tana kan jiran aiki na tsawon mintuna biyu yayin da firikwensin ya sake daidaita yanayin yanayin kafin a fara aiki na yau da kullun. Daidaiton yana cika lokacin da halin LED ya dawo daidai GREEN.

A ƙarshen nasarar daidaitawa ta Span, ana kwatanta azancin na'urar firikwensin da hankalinsa yayin aikin gyaran masana'anta na farko. Idan hankalin sa ya faɗi ƙasa ƙayyadaddun ƙarshen rayuwa na masana'anta, K-O2 yana shiga cikin Yanayin Ƙarshen Sensor tare da murfin gaban LED a hankali yana kyalkyali RED, fitowar analog a 4 mA akai-akai, kuma ana kunna faɗakarwar faɗakarwa / iska. Na'urar firikwensin iskar oxygen baya aiki kuma dole ne a maye gurbinsa (Duba sashe na 6).

MASANIN MUSULUNCI na SENSOR

Ana samun samfuran firikwensin ƙira daga Kele.

Calibrated Oxygen Sensor	Kal Kit
Shekara 5: KMOD-O2-25	UCK-1 KIT
Shekara 10: KMOD-O2-50

6.1 MAYAR DA FILIN MASANIN MUSULUNCI 
Ana iya maye gurbin na'urorin firikwensin lokacin da suka isa ƙarshen rayuwar sabis ɗin su.
Wasu lambobi na farko suna da na'urorin firikwensin firikwensin tare da firikwensin ya juya digiri 90 daga yanayin da aka nuna a ciki
Don maye gurbin na'urar firikwensin da sabon masana'anta da aka daidaita, bi matakan da ke ƙasa:

1. Bude murfin gaban mai sarrafawa.
2. Cire haɗin wutar lantarki na mai sarrafawa (duba Hoto 6).
3. Cire na'urar firikwensin ta hanyar ja da firikwensin firikwensin nesa da babban allon (Hoto na 11).
4. Toshe sabon na'urar firikwensin a cikin babu inda 'Sensor 1', sannan danna module ɗin da ƙarfi har sai da nailan ya tsaya (wanda aka nuna a hoto na 11) ya 'dauki' cikin rami a gefen hagu-hagu na allon module.
5. Toshe mai haɗa wutar lantarki.
6. Lura cewa alamar murfin gaba baya yin ja, sannan a rufe shingen mai sarrafawa.

GARANTI

7.1 LOKACI

Bangaren / Class	Tsawon Garanti
Yadi & babban allo	shekaru 7
Samfuran firikwensin	shekara 1

7.2 GARANTI IYAKA DA MAGANI.
KELE ya ba da garantin ga mai siye cewa na tsawon lokacin da aka bayyana a cikin sashin "Lokacin Garanti" da ke sama daga ranar jigilar kayayyaki zuwa mai siye cewa samfuran za su yi daidai da ƙayyadaddun samfurin da KELE ya amince da su. Wannan garanti ba za a iya canjawa wuri ba.

WANNAN GARANTIN YANA MADADIN DUKKAN WASU GARANTI, BAYANI KO BAYANI. KELE A KASANCEWA YA KARE DUKAN GARANTIN DA AKE NUFI, gami da GARANTIN SAMUN KASANCEWA DA KYAUTATA GA MUSAMMAN.
KELE BA SHI DA ALHAKIN KOTA HANYA GA CUTAR KYAUTATA, ILLAR DUKIYA, KO RAUNIN JIKI WANDA YAKE SAKAMAKON GABA DAYA KO A SASHE DAGA (1) AMFANI DA KYAU KO RASHIN HANKALI, (2) AMFANI DA IZININ YIN AMFANI KO gyare-gyare, KO (KORES) MULKI.
BABU WANI AL'AMARI DA KELE ZAI IYA HANYA GA MAI SAYA KO WANI MUTUM DON KUDIN SAMUN KAYAN SAUKI, RASHIN RIBA, KO GA WANI LALATA TA MUSAMMAN, NA FARUWA KO SAKAMAKO.
Wannan garantin baya ɗaukar:

• Rashin lahani saboda rashin amfani, cin zarafi, ko rashin dacewa ko rashin isassun kulawa, sabis, ko gyara samfuran;
• Rashin lahani saboda gyare-gyaren Samfura, ko saboda canjin su ko gyaran su da wani banda KELE;
• Matsalolin da suka taso daga rashin daidaituwa tsakanin samfuran KELE da sauran abubuwan da aka yi amfani da su tare da waɗannan samfuran ko ƙirar samfurin da aka haɗa samfuran a ciki. Mai siye ne kawai ke da alhakin tantance ko samfuran sun dace da manufar mai siye, da kuma tabbatar da cewa duk wani samfurin da aka haɗa samfuran a ciki, sauran abubuwan da aka yi amfani da su tare da samfuran KELE, da dalilan da aka yi amfani da samfuran Kele sun dace kuma sun dace da waɗannan samfuran.

Sai dai in KELE ya yarda akasin haka, don samun sabis a ƙarƙashin wannan garanti, mai siye dole ne ya shirya duk wani samfur mara daidaituwa a hankali, kuma a aika shi, wanda aka biya kafin lokaci ko na kaya, zuwa Kele, Inc. a

3300 Brother Blvd. • Memphis, TN 38133 

kafin karewar lokacin garanti. Dole ne mai siye ya haɗa da taƙaitaccen bayanin rashin daidaituwa. Duk wani aiki na keta wannan garanti dole ne a kawo shi cikin shekara guda na ƙarshen garantin.
Idan Kele ya ƙaddara cewa samfurin da aka dawo bai dace da wannan garanti ba, bisa ga shawarar Kele, ko dai gyara ko musanya wannan samfur, kuma zai aika da samfurin zuwa ga mai siye kyauta. A zaɓi na KELE, KELE na iya zaɓar mayar wa mai siye kuɗin siyan farashin siyan samfur mara daidaituwa maimakon gyara ko maye gurbinsa.

RA'AYI

8.1 Dubawa da kiyayewa
Domin kiyaye ƙayyadaddun daidaito na wannan na'urar a kan cikakken iyakar aikinta, yakamata a daidaita na'urar firikwensin ta aƙalla kowane watanni 6. A lokacin daidaitawa, ana kwatanta hankalin firikwensin da hankali yayin daidaitawar masana'anta na farko. Idan hankali ya faɗi ƙasa da ƙayyadaddun masana'anta, firikwensin ya kai ƙarshen rayuwarsa kuma dole ne a maye gurbinsa. Tuntuɓi Kele don ingantaccen tsarin maye gurbin.
A cikin yanayi mai tsauri, na'urar firikwensin na iya gazawa da wuri. Yayin aiki na yau da kullun, ana gwada firikwensin akai-akai don gano gazawar gama gari. Idan an gano gazawa, matsayin murfin gaban LED zai kiftawa sannu a hankali RED, za a kunna faɗakarwar faɗakarwa kuma fitowar analog mai ba da rahoto zai tsaya a 4 mA har sai an maye gurbin firikwensin.

BA KALE KO WANI DAGA CIKIN MASU SOYAYYARSU BA KE DA ALHAKIN KOTA HANYA DOMIN LALACEWAR KYAUTATA, LALACEWAR DUKIYA, KO RAUNIN JIKI WANDA YAKE SAMUN GABA DAYA KO A SASHE NA (1) AMFANI DA KYAU KO RASHIN HANKALI, (2) AMFANI DA IZININ 3. ) SAURAN SABABBAN WANDA Kele KO SARAUTAR DA SUKE SAMUN SA.
BABU WANI FARKO Kele KO WANI DAGA CIKIN MASU SOYAYYARSU BA SU DOKA WA MAI SAYA KO WANI MUTUM DON KUDIN SAMUN KAYAN SAUKI, RASHIN RIBA, KO GA WANI SAURAN MUSAMMAN, MAFARKI KO SAMUN LALALA.

8.2 TSARON RAI
Ba a ƙirƙira wannan rukunin, takaddun shaida, siyarwa, ko izini don amfani a aikace-aikace inda rashin nasarar wannan na'urar zai iya haifar da rauni ko mutuwa.

Kele, Inc. girma
• 3300 Brother Blvd.
• Memphis, TN 38133
www.kele.com 
5/20/2022

Takardu / Albarkatu

Kele K-O2-S5 Oxygen Detector Sensors da Transmitter [pdf] Manual mai amfani K-O2-S5.

Magana

• Manual mai amfani