Cuntrollore di Zona ZONEMIX4
“
Specificazioni
- Supports up to 8 controllers per port
- Supports ONE audio input PER accessory port
- Supports up to 8 paging stations per port
- Maximum cable length per port: 100m – 500m depending on
accessori
Istruzzioni per l'usu di u produttu
Step 1: Decide Port Wiring Layout
Decide if you need local audio inputs and allocate accessory
ports accordingly. One audio input can be used per port, while wall
controllers and paging stations can be connected to any port.
Step 2: Confirm Limits
Ensure you do not exceed the specified limits for cable length
and accessories per port as outlined in the provided table.
Step 3: Accessory Port Wiring
Follow the wiring guide provided for ZONEMIX and ZMPS wiring,
ensuring proper termination of cables to prevent signal
corruzzione.
ZONEMIX E ZMPS WIRING
Follow the T-568A wiring diagram for proper connections of
signal, paging audio, RS485, +24V DC, GND, and local input.
WP4R, WP10, WPVOL Wiring & WPBT Wiring
Follow the wiring instructions provided for each accessory port
to ensure correct connection of paging audio, RS485, +24V DC, GND,
and remote input.
Istruzzioni per a terminazione
- Terminate the ZONEMIX accessory ports based on which ports you
use using the PORT TERM switches. - Terminate l'ULTIMO accessori RS485 nantu à u cable di u portu.
FAQ
Q: How many controllers can be connected per port?
A: The system supports up to 8 controllers per port.
Q: Can multiple wall panels and paging stations be connected on
the same accessory port?
A: Yes, multiple wall panels and paging stations can be
connected on the same accessory port.
"'
GUIDA DI CABLAGGIU
INTRODUZIONE
I porti accessori ZONEMIX permettenu a cunnessione di pannelli di muru, stazioni di paginazione è fonti di input audio. Per piacè seguite a guida sottu per cunfigurà u vostru sistema.
Chjave:
ZONEMIX 4
ZONEMIX 8
Wall Controllers Audio Sources
Supporta finu à 8 controllers per portu. (vede a pagina 2 per i dettagli)
Supporta UNA entrata audio PER portu d'accessori.
Supports up to 8 paging stations per port. (see page 2 for details) Note: Supports one active page at a time. Example setup: Lots of controllers, lots of paging stations and ONE audio input.
Per piacè nutate chì i canali di input audio lucali di u portu d'accessori sò chjusi à a zona di output currispondente è solu unu pò esse usatu per zona. Per esempiu, u portu di l'accessori 1 l'input lucale si cunnetta à a Zona 1. In ogni casu, parechji pannelli murali è stazioni di paginazione ponu esse cunnessi nantu à u stessu portu d'accessori.
australianmonitor.com.au
1
STEP 1: DECIDE PORT WIRING LAYOUT
Do you need local audio inputs?
Iè
Innò
Aduprate un portu accessori per zona. ie Port 1 à Zone 1, Port 2 à Zone 2 etc. Cum'è inputs audio necessitanu u so propiu home run.
Only one audio input can be used per port. Wall controllers and paging stations can go on any port.
Use any port to any zone/s
STEP 2: CONFIRM VOI ÙN SUCCEDE I LIMITI SEGUENTI
Maximum cable length per port Accessories per port Maximum Accessories in system
100 m
8
130 m
7
180 m
6
24
250 m
5
400 m
4
500 m
3
The maximum distances quoted in the table are due to DC current limitations. The paging stations and wall panels can be locally powered to increase the cable length to a maximum
of 500m. Please read the following additional document: Advanced accessory port wiring guide.
australianmonitor.com.au
2
STEP 3: WIRING PORT ACCESSORY
Wire the ZONEMIX and ZMPS paging stations as per the images below. · Category 5, 5e and 6 cabling supported. · T-568A wiring recommended. However, T-568B also supported.
ZONEMIX AND ZMPS WIRING 1
8
*T-568A wiring
1 2 3 4 5 6 7 8
Pin Colour 1 Green/White 2 Green 3 Orange/White 4 Blue 5 Blue/White 6 Orange 7 Brown/White 8 Brown
ZONEMIX
Signal Paging Audio + Paging Audio RS485 B +24V DC GND RS485 A Local Input + Local Input –
ZMPS
CABLAGGIO ZMPS DAISY CHAIN
ZONEMIX
Use an RJ45 splitter or terminal block if daisy chain wiring required
australianmonitor.com.au
3
PASSU 3: CABLAGGI DI PORTU ACCESSORI (CONT.)
Wire the wall panels as per the images below. · Category 5, 5e and 6 cabling supported. · T-568A wiring recommended. However, T-568B also supported.
WP4R, WP10, WPVOL WIRING
WPBT WIRING
1
Paging Audio +
2
Paging Audio -
3
RS485 A
4
+ 24 V DC
5
GND
6
RS485 B
7
Input Remote +
8
Input Remote -
*Unused if not daisy chaining
Cablaggio daisy chain
*Unused unless connecting to downstream ZMPS
Cablaggio daisy chain
australianmonitor.com.au
4
STEP 4: PORT TERMINATION DO NOT SKIP THIS STEP
The ZONEMIX uses the RS485 standard to communicate to wall panels and paging stations. RS485 requires that each end of the cable run is terminated to prevent signal corruption due to signal reflections in the cable. The Accessory Ports are grouped in Pairs. 1+2, 3+4, 5+6, 7+8. You must terminate the ZONEMIX and Accessories based on which ports you use.
1. Terminate the ZONEMIX accessory ports, as per the table, using the PORT TERM switches
CONFIGURAZIONE DI INTERRUTTORE TERMINAL PORT ACCESSORY
ONE PORT USED TERM BOTH PORTS USED TERM
Port 1 OR Port 2 used Port 3 OR Port 4 used
ON Port 1 AND Port 2 used OFF
ON
ON Port 3 AND Port 4 used OFF
Port 5 OR Port 6 utilizatu
ON Port 5 AND Port 6 used OFF
Port 7 OR Port 8 utilizatu
ON Port 7 AND Port 8 used OFF
2. Terminate the LAST RS485 accessory on the port cable run.
Terminazione di a stazione di paginazione
Terminazione di u pannellu di muru
Examples:
ONE port used:
PORT TERM = ON
Terminate end points
BOTH Ports used:
PORT TERM = OFF
australianmonitor.com.au
5
PASSU 5: WP4R, WP10 GPO WIRING (OPZIONALE)
U WP4R è u WP10 anu 3 uscite di scopu generale chì ponu esse cuntrullati da i buttoni di u pannellu di u muru per attivà i dispositi esterni cum'è i proiettori.
Schema GPO
Ogni Output hè un transistor di cullezzione aperta. Massimu Voltage: 48V Corrente Massima Sink: 250mA
Example: Relay Connection
24V
Internal Logic
GPO1
GPO2
GPO3
australianmonitor.com.au
GND 6
Documenti / Risorse
 |
ZONEMIX ZONEMIX4 Zone Controller [pdf] Istruzzioni ZONEMIX4, ZONEMIX4 Zone Controller, Zone Controller, Controller |