200-18-E6B Snap-in-Output Module
Incwadi Yeziqondiso
I-V200-18-E6B ixhuma ngqo ngemuva kwama-Unitronics OPLCs ahambisanayo, idale iyunithi ye-PLC eziqukathe ngokwayo enokulungiselelwa kwe-I/O kwasendaweni.
Izici
- Okokufaka kwedijithali okungu-18 okuhlukile okulungisekayo ukuze kuthayiphe i-pnp/npn (umthombo/usinki), kufaka phakathi okokufaka kwe-shaft encoder oku-2.
- Imiphumela eyi-15 yokudlulisa ehlukanisiwe.
- 2 okuhlukile kwe-pnp/npn (umthombo/usinki) imiphumela ye-transistor, ehlanganisa okuphumayo okungu-2 kwesivinini esikhulu.
- 5 okokufaka kwe-analog, kufaka phakathi okokufaka okungu-2 okulungisekayo ku-RTD noma ku-thermocouple.
- 2 imiphumela engayodwa ye-analog.
- Ngaphambi kokusebenzisa lo mkhiqizo, kuyisibopho somsebenzisi ukufunda nokuqonda lo mbhalo nanoma yimiphi imibhalo ehambisana nawo.
- Konke exampimidwebo nemidwebo eboniswe lapha ihloselwe ukusiza ukuqonda, futhi ayiqinisekisi ukusebenza. I-Unitronics ayiwamukeli umthwalo wemfanelo wokusetshenziswa kwangempela kwalo mkhiqizo ngokusekelwe kulawa exampLes.
- Sicela ulahle lo mkhiqizo ngokuhambisana namazinga nemithetho kazwelonke yendawo nekazwelonke.
- Izisebenzi zesevisi eziqeqeshiwe kuphela okufanele zivule lolu cingo noma zilungise.
Imihlahlandlela yokuphepha kwabasebenzisi kanye nempahla yokusebenza
Lo mbhalo uhloselwe ukusiza abasebenzi abaqeqeshiwe nabanekhono ekufakweni kwalo mshini njengoba kuchazwe yiziqondiso zaseYurophu zemishini, i-low vol.tage, kanye ne-EMC. Uchwepheshe kuphela noma unjiniyela oqeqeshwe kumazinga kagesi endawo nawezwe okufanele enze imisebenzi ehambisana nezintambo zikagesi zedivayisi.
Izimpawu zisetshenziselwa ukugqamisa ulwazi oluhlobene nokuphepha komuntu siqu komsebenzisi kanye nokuvikelwa kwempahla kuyo yonke le dokhumenti.
Lapho lezi zimpawu zivela, ulwazi oluhlobene kufanele lufundwe ngokucophelela futhi luqondwe ngokugcwele.
| Uphawu | Incazelo | Incazelo |
 |
Ingozi | Ingozi ekhonjiwe idala ukulimala ngokomzimba kanye nempahla. |
 |
Isexwayiso | Ingozi ekhonjiwe ingabangela ukulimala ngokomzimba kanye nempahla. |
| Isexwayiso | Isexwayiso | Qaphela. |
- Ukwehluleka ukuthobela izinkombandlela zokuphepha ezifanele kungaholela ekulimaleni okukhulu komuntu siqu noma ekulimaleni kwempahla. Njalo sebenzisa ukuqapha okufanele lapho usebenza ngezinto zikagesi.
- Hlola uhlelo lomsebenzisi ngaphambi kokulusebenzisa.
- Ungazami ukusebenzisa le divayisi ngemingcele eyeqa amazinga avunyelwe.
- Faka i-circuit breaker yangaphandle futhi uthathe izinyathelo ezifanele zokuphepha ngokumelene ne-shortcircuit kuzintambo zangaphandle.
- Ukuze ugweme ukulimaza isistimu, ungaxhumeki / unganqamuli idivayisi lapho amandla avuliwe.
Isexwayiso
- Qinisekisa ukuthi amabhulokhi etheminali avikelwe ngendlela efanele endaweni yawo.
Ukucatshangelwa Kwemvelo
- Ungafaki ezindaweni: ezinothuli oluningi noma oluhambisayo, igesi ebolayo noma evuthayo, umswakama noma imvula, ukushisa okudlulele, ukushaqeka okujwayelekile noma ukudlidliza okukhulu.
- Nikeza umoya ofanele ngokushiya okungenani isikhala esingu-10mm phakathi kwamaphethelo angaphezulu naphansi ocingo kanye nezindonga ezivalekile.
- Ungawabeki emanzini noma uvumele amanzi avuzele eyunithi.
- Ungavumeli imfucumfucu iwele ngaphakathi kweyunithi phakathi nokufakwa.
Ukuhambisana kwe-UL
Isigaba esilandelayo sihambisana nemikhiqizo ye-Unitronics esohlwini lwe-UL.
Amamodeli alandelayo: V200-18-E1B, V200-18-E2B, V200-18-E6B, V200-18-E6BL afakwe kuhlu lwe-UL Lwezindawo Eziyingozi.
The following models: V200-18-E1B, V200-18-E2B, V200-18-E3B, V200-18-E3XB, V200-18-E46B, V200-18-E46BL, V200-18-E4B, V200-18-E4XB,
I-V200-18-E5B, V200-18-E6B, V200-18-E6BL, V200-18-ECB, V200-18-ECXB, V200-18-ESB zifakwe kuhlu Lwendawo Ejwayelekile.
Izilinganiso ze-UL, Izilawuli Ezihlelekayo ezizosetshenziswa Ezindaweni Eziyingozi, Ikilasi I, Isigaba 2, Amaqembu A, B, C kanye no-D
Lawa manothi okukhishwa ahlobene nayo yonke imikhiqizo ye-Unitronics enezimpawu ze-UL ezisetshenziselwa ukumaka imikhiqizo egunyazwe ukusetshenziswa ezindaweni eziyingozi, Ikilasi I, Isigaba 2, Amaqembu A, B, C kanye no-D.
Izilinganiso Zokumelana Nokukhipha Okudluliselweyo
Imikhiqizo ebhalwe ngezansi iqukethe okuphumayo kwe-relay: V200-18-E1B, V200-18-E2B.
- Uma le mikhiqizo ethile isetshenziswa ezindaweni eziyingozi, ikalwa ku-3A res, lapho le mikhiqizo ethile isetshenziswa ezimweni ezingezona eziyingozi zemvelo, ikalwa ku-5A res, njengoba inikezwe ekucacisweni komkhiqizo.
Izintambo
- Ungazithinti izintambo ezibukhoma.
- Izikhonkwane ezingasetshenzisiwe akufanele zixhunywe. Ukuziba lesi siqondiso kungase kulimaze idivayisi.
- Ungaxhumi isignali 'Yokumaphakathi' noma 'Yolayini' ye-110/220VAC kuphinikhodi ye-0V yedivayisi.
- Hlola kabili zonke izintambo ngaphambi kokuvula ugesi.
Izinqubo zezintambo
Sebenzisa amatheminali e-crimp ukwenza izintambo; sebenzisa intambo engu-26-12 AWG (0.13mm2 –3.31mm 2 ) kuzo zonke izinjongo zokufaka izintambo.
- Hlikihla ucingo lube ubude obungu-7±0.5mm (0.250–0.300 amayintshi).
- Khipha itheminali endaweni yayo ebanzi kakhulu ngaphambi kokufaka intambo.
- Faka intambo ngokuphelele kutheminali ukuze uqinisekise ukuthi kungenziwa uxhumano olufanele.
- Qinisa ngokwanele ukugcina intambo ingadonsi mahhala.
▪ Ukuze ugweme ukulimaza ucingo, ungeqi i-torque engu-0.5 N·m (5 kgf·cm).
▪ Ungasebenzisi ithini, i-solder, nanoma iyiphi enye into ocingweni olukhumuliwe olungase lunqamuke umucu wocingo.
▪ Faka ebangeni eliphezulu ukusuka ku-high-voltagizintambo ze-e kanye nempahla yamandla.
I/O Wiring—General
- Amakhebuli okokufaka noma okukhiphayo akufanele asetshenziswe ngentambo efanayo yama-multi-core noma abelane ngentambo efanayo.
- Vumela ivolumutagUkuphazamiseka kwe-e nomsindo nemigqa yokufaka esetshenziswa ebangeni elinwetshiwe.
Sebenzisa intambo enosayizi ofanele wokulayisha.
Ukuhlanza umkhiqizo
Ukuze ukwandise ukusebenza kwesistimu, gwema ukuphazamiseka kwe-electromagnetic ngale ndlela elandelayo:
- Sebenzisa ikhabethe lensimbi.
- Xhuma i-0V kanye namaphoyinti aphansi asebenzayo (uma ekhona) ngokuqondile emhlabathini wohlelo.
- Sebenzisa okufushane kakhulu, okungaphansi kuka-1m (3.3 ft.) nokujiya kakhulu, 2.08mm² (14AWG) min, izintambo ezingaba khona.
Okokufaka Kwedijithali
Iqembu ngalinye lezinto ezifakiwe ezingu-9 linesignali evamile. Iqembu ngalinye lingasetshenziswa njenge-pnp (umthombo) noma i-npn (usinki), uma kunezintambo ezifanele njengoba kuboniswe kwizibalo ezilandelayo.
- Okokufaka kwe-I0 ne-I2 kungasetshenziswa njengokufakwayo okujwayelekile kwedijithali, njengezibali zesivinini esikhulu, noma njengengxenye yesishumeki se-shaft.
- Okokufaka kwe-I1 ne-I3 kungasetshenziswa njengokufakwayo okujwayelekile kwedijithali, njengokusetha kabusha izinto zokubala ezinesivinini esikhulu, noma njengengxenye yesishumeki se-shaft.
Okokufaka i-I0, i-I1, ne-I2, i-I3 ingasetshenziswa njengezifaki khodi ze-shaft njengoba kuboniswe ngezansi.
Imiphumela Yedijithali
Izimpahla Zamandla Ezintambo
Sebenzisa amandla kagesi angu-24VDC kukho kokubili ukuphuma kwe-relay ne-transistor.
- Xhuma intambo “enhle” kutheminali ethi “V1”, bese kuthi “negative” iholele kutheminali ethi “0V”.
▪ Uma kwenzeka voltage ukuguquguquka noma ukungahambisani nevolumutage ukucaciswa kwe-powersupply, xhuma idivayisi ekunikezeni amandla okulawulwayo.
Imiphumela yokudluliswa
- Iqembu ngalinye lingaxhunywa izintambo ngokwehlukana ku-AC noma ku-DC njengombukiso.
- Isignali engu-0V yokuphumayo kwe-relay ihlukanisiwe kusignali engu-0V yesilawuli.
Ukwandisa Isikhathi Sokuphila Sokuxhumana
Ukuze ukhuphule ubude besikhathi sempilo yabathintana nabo abaphumayo futhi uvikele idivayisi emonakalweni ongase ube khona nge-EMF ehlehlayo, xhuma:
- a clamping diode ngokuhambisana nomthwalo ngamunye we-DC ongenisayo,
- isekethe ye-RC snubber ngokuhambisana nomthwalo ngamunye we-AC ongenisayo.
Imiphumela ye-Transistor
- Okukhiphayo ngakunye kungenziwa ngezintambo ngokwehlukana njenge-npn noma i-pnp.
- Isignali engu-0V yemiphumela ye-transistor ihlukanisiwe kusignali ye-0V yesilawuli.
Okokufaka kwe-Analog
5 okokufaka kwe-analog:
- Okokufaka 0 kuya ku-2 kungaxhunywa ngentambo ukuze kusebenze ngokwamanje noma ngevolumutage.
- Okokufaka 3 kanye no-4 kungasebenza njenge-analog, i-RTD, noma i-thermocouple, uma kunezintambo ezifanele njengoba kuboniswe kuzibalo ezilandelayo.
Ukuze ulungiselele okokufaka, vula idivayisi bese usetha ama-jumpers ngokwemiyalelo eqala ekhasini 8. Izihlangu kufanele zixhunywe kumthombo wesignali.
Okokufaka kwe-Analog
- Uma isethwe ku-current/voltage, konke okokufaka kwabelana ngesignali ye-ACM evamile, okumele ixhunywe ku-0V yesilawuli.
Okokufaka kwe-RTD
- I-PT100 (Inzwa 3): sebenzisa kokubili okokufaka okuhlobene nesignali ye-CM3.
- I-PT100 (Inzwa 4): sebenzisa kokubili okokufaka okuhlobene nesignali ye-CM4.
- 4 wire PT100 ingasetshenziswa ngokushiya eyodwa yezinzwa ingaxhumekile.
Okokufaka kwe-Thermocouple
- Izinhlobo ze-thermocouple ezisekelwayo zifaka u-B, E, J, K, N, R, S, no-T, ngokuvumelana nesofthiwe nezilungiselelo ze-jumper. Bheka ithebula, Izigaba Zokufaka ze-Thermocouple, ekhasini 13.
- Okokufaka kungase kusethelwe ku-mV ngezilungiselelo zesofthiwe (Ukucushwa Kwezingxenyekazi zekhompyutha); qaphela ukuthi ukuze usethe okokufaka kwe-mV, kusetshenziswe izilungiselelo ze-thermocouple jumper.
- Ukuqinisekisa ukusebenza kahle, kunconywa isikhathi sokufudumala sesigamu sehora.
I-Analog Outputs Power Supply
Sebenzisa amandla kagesi angu-24VDC kuwo wonke amamodi okukhiphayo e-analog.
- Xhuma ikhebula “positive” kutheminali ethi “V2”, kanye nethi “negative” kutheminali ethi “0V”.
▪ Uma kwenzeka voltage ukuguquguquka noma ukungavumelani nevolumutage ukucaciswa kokunikezwa kwamandla, xhuma idivayisi ekunikezeni amandla okulawulwayo.
▪ Njengoba ugesi we-analog I/O uhlukanisiwe, isilawuli sikagesi esingu-24VDC singase sisetshenziselwe ukunika amandla i-analog I/Os.
Ukunikezwa kwamandla kwe-24VDC kufanele kuvulwe futhi kucishwe kanyekanye nokuphakelwa kwamandla kwesilawuli. 
Imiphumela ye-Analog
- Izihlangu kufanele zenziwe umhlabathi, zixhunywe emhlabeni wekhabhinethi.
- Okuphumayo kungenziwa ngentambo kuya ku-current noma ku-voltage, sebenzisa izintambo ezifanele njengoba kukhonjisiwe ngezansi.
- Ungasebenzisi i-current ne-voltage kusuka esiteshini somthombo ofanayo.
Ukushintsha Izilungiselelo Ze-Jumper
Ukuze ufinyelele ama-jumper, kufanele ususe imojuli ye-snap-in I/O kusilawuli, bese ukhipha ibhodi le-PCB lemojuli.
- Ngaphambi kokuthi uqale, cisha ukunikezwa kwamandla, nqamula futhi ukhiphe isilawuli.
- Ngaphambi kokwenza lezi zenzo, thinta into esekelwe phansi ukuze ukhiphe noma iyiphi inkokhiso ye-electrostatic.
- Gwema ukuthinta ibhodi le-PCB ngokuqondile ngokubamba ibhodi le-PCB ngezixhumi zalo.
Ukufinyelela kuma-Jumpers
Okokuqala, susa imojuli ye-snap-in.
- Thola izinkinobho ezi-4 ezinhlangothini zemojuli, ezi-2 nhlangothi zombili. Cindezela izinkinobho ezi-2 nhlangothi zombili zemojuli njengoba kukhonjisiwe, bese uzibambe phansi ukuze uvule indlela yokukhiya.
- Gcwalisa kancane imojuli ukusuka ohlangothini ukuya kwelinye, wenza lula imojuli ukusuka kusilawuli.
- Usebenzisa i-screwdriver ye-Philips, susa isikulufu esimaphakathi ebhodini le-PCB lemojuli.
Khetha umsebenzi owufunayo ngokushintsha izilungiselelo ze-jumper ngokusho kwesibalo namathebula aboniswe ngezansi.
| I-Jumper # | Voltage* | Okwamanje | |
| Okokufaka kwe-analog 0 | 3 | V | I |
| Okokufaka kwe-analog 1 | 2 | V | I |
| Okokufaka kwe-analog 2 | 1 | V | I |
| I-Jumper # | Voltage* | Okwamanje | I-TIC noma i-mV | PT1 | |
| Okokufaka kwe-analog 3 | 5 | AN | AN | I-PT-TC | I-PT-TC |
| 7 | V | I | V | V | |
| Okokufaka kwe-analog 4 | 4 | AN | AN | I-PT-TC | I-PT-TC |
| 6 | V | I | V | V |
* Ukulungiselelwa kwefekthri okuzenzakalelayo
Ukuhlanganisa kabusha isilawuli
- Buyisela ibhodi le-PCB kumojuli futhi uvikele isikulufu esimaphakathi.
- Okulandelayo, faka kabusha imojuli. Layisha imihlahlandlela eyindilinga kusilawuli kanye nemihlahlandlela ye-Snap-in I/O Module njengoba kukhonjisiwe ngezansi.
- Faka ingcindezi elinganayo kuwo wonke amakhona angu-4 uze uzwe 'ukuchofoza' okuhlukile. Imojula isifakiwe manje. Hlola ukuthi zonke izinhlangothi namakhona kubekwe ngendlela efanele yini.
I-V200-18-E6B Imininingwane Yobuchwepheshe
| Inombolo yokokufaka | 18 (ngamaqembu amabili) |
| Uhlobo lokokufaka | pnp (umthombo) noma i-npn (usinki) |
| Ukuhlukaniswa kwe-galvanic | |
| Okokufaka kwedijithali ebhasini | Yebo |
| Okokufaka kwedijithali kokokufaka kwedijithali | Cha |
| iqembu elifanayo | |
| Iqembu ngeqembu, okokufaka kwedijithali | Yebo |
| Okokufaka okuzenzakalelayo voltage | 24VDC |
| Okokufaka ivoltage | |
| pnp (umthombo) | I-0-5VDC ye-Logic '0' I-17-28.8VDC ye-Logic '1' |
| npn (usinki) | I-17-28.8VDC ye-Logic '0' I-0-5VDC ye-Logic '1' |
| Okokufaka kwamanje | 6mA@24VDC kuma-inputs 4 kuya ku-17 8.8mA@24VDC kuma-inputs 0 kuya ku-3 |
| Isikhathi sokuphendula | 10mSec ejwayelekile |
| Okokufaka kwesivinini esikhulu | Imininingwane engezansi iyasebenza uma lokhu okokufaka kunentambo ukuze kusetshenziswe njengesivinini esikhulu isifaki khodi se-counter/shaft. Bheka Amanothi 1 no-2. |
| Isixazululo | 32-bit |
| Imvamisa | 10kHz esiphezulu |
| Ububanzi be-pulse obuncane | 40μs |
Amanothi:
- Okokufaka okungu-0 no-2 ngakunye kungasebenza njengesibali sesivinini esikhulu noma njengengxenye yesishumeki se-shaft. Esimeni ngasinye, imininingwane yokufaka yesivinini esiphezulu iyasebenza. Uma kusetshenziswa okokufaka kwedijithali okujwayelekile, kuyasebenza izicaciso ezijwayelekile zokufakwayo.
- Okokufaka 1 kanye no-3 kungasebenza ngakunye njengokusethwa kabusha kwekhawunta, noma njengokufakwayo okuvamile kwedijithali; kunoma yikuphi, ukucaciswa kwayo kungokokufaka kwedijithali okujwayelekile. Lokhu okokufaka kungase futhi kusetshenziswe njengengxenye yesishumeki se-shaft. Kulesi simo, imininingwane yokufaka yesivinini esiphezulu iyasebenza.
Amanothi:
Idivayisi ingaphinda ilinganise ivolumutage phakathi kwebanga -5 kuya ku-56mV, ngesixazululo esingu-0.01mV. Idivayisi ingaphinda ilinganise imvamisa yenani elingahluziwe ngokulungiswa okungu-14-bits (16384). Ububanzi bokufaka buboniswa kuthebula elilandelayo:
Ithebula 1: Ububanzi bokufaka kwe-Thermocouple
| Uhlobo | Ibanga lokushisa | Intambo ye-ANSI (USA) | Umbala I-BS 1843 (UK) |
| mV | -5 kuya ku-56nnV | – | – |
| B | 200 kuya ku-1820°C (300 ukuya ku-3276°F) |
+Mpunga -Bomvu |
+Lutho -Blue |
| E | -200 kuya ku-750 ° C (-328 ukuya ku-1382°F) |
+Violet -Bomvu |
+Brown -Blue |
| J | -200 kuya ku-760 ° C (-328 ukuya ku-1400°F) |
+Mhlophe -Bomvu |
+Okuphuzi -Blue |
| K | -200 kuya ku-1250 ° C (-328 ukuya ku-2282°F) |
+Okuphuzi -Bomvu |
+Brown -Blue |
| N | -200 kuya ku-1300 ° C (-328 ukuya ku-2372°F) |
+Owolintshi -Bomvu |
+Owolintshi -Blue |
| R | 0 kuya ku-1768°C (32 ukuya ku-3214°F) |
+Mnyama -Bomvu |
+Mhlophe -Blue |
| S | 0 kuya ku-1768°C (32 ukuya ku-3214°F) |
+Mnyama -Bomvu |
+Mhlophe -Blue |
| T | -200 kuya ku-400 ° C (-328 ukuya ku-752°F) |
+Okuluhlaza okwesibhakabhaka -Bomvu |
+Mhlophe -Blue |
I-Unitronics
| Ezemvelo | IP20 / NEMA1 |
| Izinga lokushisa lokusebenza | 0° ukuya ku-50°C (32° ukuya ku-122°F) |
| Izinga lokushisa lesitoreji | -20° ukuya ku-60°C (-4° ukuya ku-140°F) |
| Umswakamo Ohlobene (RH) | 10% kuya ku-95% (okungafinyeleli) |
| Ubukhulu (WxHxD) | 138x23x123mm (5.43×0.9×4.84”) |
| Isisindo | 140g (4.94oz) |
Ulwazi olukulo mbhalo lubonisa imikhiqizo ngosuku lokuphrinta. I-Unitronics igodla ilungelo, kuncike kuyo yonke imithetho esebenzayo, nganoma yisiphi isikhathi, ngokubona kwayo kuphela, futhi ngaphandle kwesaziso, lokuyeka noma ukushintsha izici, imiklamo, izinto zokwakha kanye neminye imininingwane yemikhiqizo yayo, kanye nokuhoxisa unomphela noma okwesikhashana noma yikuphi abashiye emakethe.
Lonke ulwazi kule dokhumenti lunikezwa “njengoba lunjalo” ngaphandle kwewaranti yanoma yiluphi uhlobo, evezwayo noma eshiwo, kuhlanganisa kodwa kungagcini kunoma yiziphi iziqinisekiso ezisikiselwayo zokuthengiselana, ukufaneleka kwenjongo ethile, noma ukungaphuli umthetho. I-Unitronics ayithwesi icala ngamaphutha noma ukweqiwa kolwazi olwethulwe kulo mbhalo. Akukho mcimbi lapho i-Unitronics izobophezeleka khona nganoma yimuphi umonakalo okhethekile, wengozi, ongaqondile noma umphumela wanoma yiluphi uhlobo, noma yimuphi umonakalo ovela ngenxa noma ohlobene nokusetshenziswa noma ukwenziwa kwalolu lwazi.
Amagama okuhweba, izimpawu zokuhweba, amalogo kanye nezimpawu zesevisi ezivezwe kulo mbhalo, kuhlanganisa nokwakheka kwazo, kuyimpahla ye-Unitronics (1989) (R”G) Ltd. noma ezinye izinkampani zangaphandle futhi awuvunyelwe ukuzisebenzisa ngaphandle kwemvume ebhalwe ngaphambili. ze-Unitronics noma umuntu wesithathu ongase abe ngabanikazi bazo
Amadokhumenti / Izinsiza
 |
unitronics V200-18-E6B Snap-in-Output Module [pdf] Incwadi Yeziqondiso I-V200-18-E6B i-Snap-in-Output Module, i-V200-18-E6B, i-Snap-in-Output Module, imojula yokukhipha-kokufakayo, imojuli yokuphumayo, imojuli |
