200-18-E6B iModyuli yokuNgenisa-Imveliso ekhawulezayo
Incwadi Yemiyalelo
Iiplagi ze-V200-18-E6B ngqo ngasemva kwee-Unitronics OPLCs ezihambelanayo, zenza iyunithi ye-PLC ezimeleyo kunye noqwalaselo lwe-I / O yendawo.
Iimbonakalo
- I-18 yezixhobo ezizimeleyo zedijithali ezilungelelaniswayo ukuchwetheza i-pnp / npn (umthombo / i-sink), iquka igalelo le-2 shaft encoder.
- I-15 yeziphumo ezizimeleyo zokudluliselwa.
- I-2 eyodwa i-pnp / npn (umthombo / i-sink) iziphumo ze-transistor, zibandakanya iziphumo ezi-2 zesantya esiphezulu.
- I-5 ye-analog inputs, ibandakanya i-2 igalelo elilungelelanisiweyo kwi-RTD okanye i-thermocouple.
- 2 iziphumo ezizimeleyo ze-analog.
- Ngaphambi kokusebenzisa le mveliso, luxanduva lomsebenzisi ukufunda nokuqonda olu xwebhu kunye nawaphi na amaxwebhu akhaphayo.
- Zonke exampIiles kunye nemizobo eboniswe apha yenzelwe ukunceda ukuqonda, kwaye ayiqinisekisi ukusebenza. I-Unitronics ayilwamkeli uxanduva lokusetyenziswa kokwenene kwale mveliso ngokusekelwe kwezi examples.
- Nceda ulahle le mveliso ngokuhambelana nemigangatho kunye nemimiselo yendawo kunye neyesizwe.
- Kuphela ngabasebenzi benkonzo abaqeqeshiweyo ekufuneka basivule esi sixhobo okanye basilungise.
Ukhuseleko lomsebenzisi kunye nezikhokelo zokukhusela izixhobo
Olu xwebhu lujolise ekuncedeni abasebenzi abaqeqeshiweyo nabanobuchule ekufakeni esi sixhobo njengoko kuchazwa yimiyalelo yaseYurophu koomatshini, ivolthi ephantsi.tage, kunye ne-EMC. Kuphela ligcisa okanye injineli eqeqeshwe kwimigangatho yombane yasekhaya neyesizwe ekufuneka yenze imisebenzi enxulumene neengcingo zombane zesixhobo.
Iimpawu zisetyenziselwa ukuqaqambisa ulwazi olunxulumene nokhuseleko lomsebenzisi kunye nokhuseleko lwesixhobo kulo lonke olu xwebhu.
Xa le miqondiso ibonakala, ulwazi olunxulumeneyo kufuneka lufundwe ngenyameko kwaye luqondwe ngokupheleleyo.
| Uphawu | Intsingiselo | Inkcazo |
 |
Ingozi | Ingozi echongiweyo ibangela umonakalo emzimbeni kunye nepropathi. |
 |
Isilumkiso | Ingozi echongiweyo inokubangela umonakalo emzimbeni kunye nepropathi. |
| Isilumkiso | Isilumkiso | Lumka. |
- Ukungaphumeleli ukuthobela izikhokelo zokhuseleko ezifanelekileyo kunokubangela ukwenzakala kakhulu okanye umonakalo wepropati. Ngalo lonke ixesha sebenzisa inkathalo efanelekileyo xa usebenza ngezixhobo zombane.
- Jonga inkqubo yomsebenzisi phambi kokuba uyiqhube.
- Musa ukuzama ukusebenzisa esi sixhobo ngeeparamitha ezidlula imigangatho evumelekileyo.
- Faka i-breaker circuit yangaphandle kwaye uthathe amanyathelo afanelekileyo okhuseleko ngokuchasene ne-shortcircuiting kwi-wiring yangaphandle.
- Ukunqanda ukonakalisa isixokelelwano, musa ukuqhagamshelwa/uqhawule uqhagamshelo isixhobo xa umbane uvuliwe.
Isilumkiso
- Qinisekisa ukuba iibhloko zetheminali zikhuselwe ngokufanelekileyo kwindawo yazo.
Ukuqwalaselwa kokusingqongileyo
- Musa ukufaka kwiindawo ezine: uthuli olugqithisileyo okanye oluqhubekileyo, igesi edlayo okanye enokutsha, ukufuma okanye imvula, ubushushu obugqithisileyo, ukothuka kwempembelelo rhoqo okanye ukungcangcazela okugqithisileyo.
- Ukubonelela ngokungena komoya okufanelekileyo ngokushiya ubuncinane i-10mm yesithuba phakathi kweencam eziphezulu nasezantsi zesixhobo kunye neendonga ezivaliweyo.
- Musa ukubeka emanzini okanye ukuvumela amanzi avuze kwiyunithi.
- Musa ukuvumela i-debris iwele ngaphakathi kwiyunithi ngexesha lofakelo.
Ukuthotyelwa kwe-UL
Eli candelo lilandelayo lifanelekile kwiimveliso ze-Unitronics ezidweliswe kunye ne-UL.
Le mizekelo ilandelayo: V200-18-E1B, V200-18-E2B, V200-18-E6B, V200-18-E6BL i-UL idweliswe kwiiNdawo ezinobungozi.
The following models: V200-18-E1B, V200-18-E2B, V200-18-E3B, V200-18-E3XB, V200-18-E46B, V200-18-E46BL, V200-18-E4B, V200-18-E4XB,
V200-18-E5B, V200-18-E6B, V200-18-E6BL, V200-18-ECB, V200-18-ECXB, V200-18-ESB zidweliswe UL Indawo eqhelekileyo.
Imilinganiselo ye-UL, abalawuli abaCwangcisiweyo abaSebenzisa kwiiNdawo ezinobungozi, iKlasi I, iCandelo 2, Amaqela A, B, C kunye no-D
La maNqaku oKhupho anxulumene nazo zonke iimveliso ze-Unitronics ezineempawu ze-UL ezisetyenziselwa ukuphawula iimveliso ezivunyiweyo ukuba zisetyenziswe kwiindawo ezinobungozi, iKlasi yoku-I, iCandelo lesi-2, iQela A, B, C kunye no-D.
Relay Output Resistance Ratings
Iimveliso ezidweliswe ngezantsi ziqulethe iziphumo zokudluliselwa: V200-18-E1B, V200-18-E2B.
- Xa ezi mveliso zikhethekileyo zisetyenziselwa kwiindawo ezinobungozi, zilinganiswe kwi-3A res, xa ezi mveliso zikhethekileyo zisetyenziselwa iimeko zokusingqongileyo ezingenabungozi, zilinganiswe kwi-5A res, njengoko zinikwe kwiinkcukacha zemveliso.
Iintambo
- Musa ukubamba iingcingo eziphilayo.
- Izikhonkwane ezingasetyenziswanga akufanele zidityaniswe. Ukungawuhoyi lo myalelo kungonakalisa isixhobo.
- Musa ukuqhagamshela i-'Neutral' okanye 'Layini' isignali ye-110/220VAC kwi-pin ye-0V yesixhobo.
- Jonga kwakhona zonke iintambo phambi kokuba uvule unikezelo lombane.
Iinkqubo zocingo
Sebenzisa iitheminali zecrimp kwi-wiring; sebenzisa i-26-12 AWG ucingo (0.13mm2 -3.31mm 2) kuzo zonke iinjongo zocingo.
- Hlubula ucingo ukuya kubude be-7±0.5mm (0.250-0.300 intshi).
- Khulula i-terminal ukuya kwindawo yayo ebanzi phambi kokufaka ucingo.
- Faka ucingo ngokupheleleyo kwi-terminal ukuqinisekisa ukuba uqhagamshelwano olufanelekileyo lunokwenziwa.
- Qinisa ngokwaneleyo ukugcina ucingo lungatsali lukhululekile.
▪ Ukuze ugweme ukonakalisa ucingo, ungagqithisi kwi-torque engu-0.5 N·m (5 kgf·cm).
▪ Musa ukusebenzisa itoti, i-solder, okanye nayiphi na enye into kucingo olukhutshiweyo olunokubangela ukuba umsonto wocingo uqhawuke.
▪ Faka kumgama omde ukusuka kwivolthi ephezulutagiintambo kunye nezixhobo zombane.
I/O Wiring—General
- Iingcingo zokufaka okanye eziphumayo akufuneki ziqhutywe ngentambo enye ye-multi-core okanye kwabelwane ngocingo olufanayo.
- Vumela umqulutagUkuwa kunye nokuphazamiseka kwengxolo kunye nemigca yegalelo esetyenziswa kumgama owandisiweyo.
Sebenzisa ucingo olulinganiswe ngokufanelekileyo kumthwalo.
Earthing imveliso
Ukwandisa ukusebenza kwenkqubo, thintela ukuphazamiseka kwe-electromagnetic ngolu hlobo lulandelayo:
- Sebenzisa ikhabhinethi yentsimbi.
- Xhuma i-0V kunye neendawo ezisebenzayo zomhlaba (ukuba zikhona) ngokuthe ngqo kumhlaba womhlaba wenkqubo.
- Sebenzisa eyona imfutshane, ingaphantsi kwe-1m (3.3 ft.) kunye nengqindilili, 2.08mm² (14AWG) min, iingcingo ezinokubakho.
Iingeniso zeDijithali
Iqela ngalinye lamagalelo ayi-9 linophawu oluqhelekileyo. Iqela ngalinye linokusetyenziswa njenge-pnp (umthombo) okanye i-npn (isinki), xa ifakwe iintambo ngokufanelekileyo njengoko kubonisiwe kula manani alandelayo.
- Iingeniso ze-I0 kunye ne-I2 zingasetyenziswa njengeengeniso zedijithali eziqhelekileyo, njengezixhobo zokubala zesantya esiphezulu, okanye njengenxalenye ye-encoder shaft.
- Iingeniso ze-I1 kunye ne-I3 zingasetyenziswa njengeengeniso zedijithali eziqhelekileyo, njenge-reset counter-speed counter, okanye njengenxalenye ye-encoder shaft.
Ukufakwa kwe-I0, i-I1, kunye ne-I2, i-I3 ingasetyenziswa njengeekhowudi ze-shaft njengoko kuboniswe ngezantsi.
Iziphumo zeDijithali
Unikezelo lwamandla ombane
Sebenzisa i-24VDC unikezelo lwamandla kuzo zombini iireyiyi kunye neziphumo zetransistor.
- Xhuma i-"positive" ekhokelela kwi-terminal "V1", kwaye "negative" ikhokelela kwi-terminal "0V".
▪ Kwimeko yomqulutage ukuguquguquka okanye ukungahambelani nomqulutage iinkcukacha zonikezelo lwamandla, qhagamshela isixhobo kunikezelo lwamandla olulawulwayo.
Ukudlulisa Iziphumo
- Iqela ngalinye linokutsalelwa ngokwahlukeneyo nokuba yi-AC okanye i-DC njengomboniso.
- Isignali ye-0V yeziphumo ze-relay ibekwe yodwa kwisilawuli se-0V yomlawuli.
Ukwandiswa koQhagamshelwano lweSithuba soBomi
Ukwandisa ubude bobomi babafowunelwa abaphumayo kunye nokukhusela isixhobo kumonakalo onokubakho nge-EMF ebuyela umva, qhagamshela:
- a clampukudibanisa idiode ngokunxuseneyo nomthwalo ngamnye we-DC osebenzayo,
- isekethe ye-RC snubber ngokunxuseneyo nomthwalo ngamnye we-AC inductive.
Iziphumo zeTransistor
- Imveliso nganye inokutsalwa ngokwahlukeneyo njenge-npn okanye i-pnp.
- Umqondiso we-0V weziphumo ze-transistor ubekwe yodwa kwisilawuli se-0V somlawuli.
Igalelo le-Analog
5 amagalelo e-analog:
- Amagalelo ku-0 ukuya ku-2 anokudityaniswa ukuze asebenze nokuba ngeyangoku okanye ngevolthitage.
- Ukufakwa kwe-3 kunye ne-4 inokusebenza njenge-analog, i-RTD, okanye i-thermocouple, xa ifakwe ngokufanelekileyo intambo njengoko kuboniswe kula manani alandelayo.
Ukuqwalasela igalelo, vula isixhobo kwaye usete i-jumpers ngokwemiyalelo eqala kwiphepha lesi-8. Izikhuselo kufuneka ziqhagamshelwe kumthombo wesignali.
Igalelo le-Analog
- Xa imiselwe kungoku/umthamotage, onke amagalelo abelana ngesignali ye-ACM eqhelekileyo, ekufuneka ixhunywe kwi-0V yomlawuli.
Igalelo le-RTD
- I-PT100 (i-Sensor 3): sebenzisa zombini iingeniso ezinxulumene nomqondiso we-CM3.
- I-PT100 (i-Sensor 4): sebenzisa zombini iingeniso ezinxulumene nomqondiso we-CM4.
- I-4 intambo ye-PT100 ingasetyenziswa ngokushiya enye ye-sensor ekhokelela ingaxhunywanga.
Iingeniso zeThermocouple
- Iintlobo ze-thermocouple ezixhaswayo ziquka i-B, E, J, K, N, R, S, kunye ne-T, ngokuhambelana nesofthiwe kunye ne-jumper settings. Jonga itheyibhile, Uluhlu lweNgeniso lweThermocouple, kwiphepha le-13.
- Izinto ezifakwayo zinokusetwa kwi-mV ngoseto lwesoftware (Ubumbeko lweHardware); Qaphela ukuba ukuze usete amagalelo e-mV, useto lwe-jumper ye-thermocouple luyasetyenziswa.
- Ukuqinisekisa ukusebenza okufanelekileyo, kucetyiswa ixesha lokufudumala kwesiqingatha seyure.
Ubonelelo lwaMandla lweZiphumo zeAnalog
Sebenzisa unikezelo lwamandla lwe-24VDC kuzo zonke iindlela zokuphuma kwe-analog.
- Qhagamshela intambo ethi “positive” kwitheminali “V2”, kunye ne “negative” kwitheminali “0V”.
▪ Kwimeko yomqulutage ukuguquguquka okanye ukungahambelani nomqulutage iinkcukacha zonikezelo lwamandla, qhagamshela isixhobo kunikezelo lwamandla olulawulwayo.
▪ Ekubeni unikezelo lwamandla lwe-analog I/O lubekwe lodwa, unikezelo lwamandla lomlawuli we-24VDC lunokusetyenziselwa ukunika amandla i-analog I/Os.
Umbane we-24VDC kufuneka uvulwe kwaye ucinywe ngaxeshanye nonikezelo lombane lomlawuli. 
Iziphumo zeAnalog
- Izikhuselo kufuneka zifakwe emhlabeni, zixhunywe kumhlaba wekhabhinethi.
- Imveliso inokutsalwa ukuba ibe yangoku okanye ivolthitage, sebenzisa iingcingo ezifanelekileyo njengoko kubonisiwe ngezantsi.
- Musa ukusebenzisa yangoku kunye voltage ukusuka kwijelo lomthombo ofanayo.
Ukutshintsha Izicwangciso zeJumper
Ukufikelela kwi-jumpers, kufuneka ususe imodyuli ye-snap-in I/O kumlawuli, kwaye emva koko ususe ibhodi yePCB yemodyuli.
- Ngaphambi kokuba uqalise, cima unikezelo lwamandla, qhawula kwaye ukhuphe isilawuli.
- Phambi kokwenza ezi ntshukumo, bamba into esekelwe phantsi ukukhupha nayiphi na intlawulo ye-electrostatic.
- Kuphephe ukubamba ibhodi PCB ngqo ngokubamba ibhodi PCB izihlanganisi yayo.
Ukufikelela kwiiJumpers
Okokuqala, susa imodyuli ye-snap-in.
- Khangela amaqhosha ama-4 kumacala emodyuli, ama-2 macala omabini. Cinezela amaqhosha ama-2 macala omabini emodyuli njengoko kubonisiwe, kwaye uwabambe ezantsi ukuvula indlela yokutshixa.
- Gcoba ngobunono imodyuli ukusuka kwelinye icala ukuya kwelinye, ulula imodyuli ukusuka kumlawuli.
- Ukusebenzisa i-screwdriver ye-Philips, susa isikrufu esiphakathi kwibhodi ye-PCB yemodyuli.
Khetha umsebenzi ofunekayo ngokutshintsha useto lwe-jumper ngokomzobo kunye neetafile eziboniswe ngezantsi.
| Umtsi # | Umqulutage* | Okwangoku | |
| Igalelo leAnalog 0 | 3 | V | I |
| Igalelo leAnalog 1 | 2 | V | I |
| Igalelo leAnalog 2 | 1 | V | I |
| Umtsi # | Umqulutage* | Okwangoku | TIC okanye mV | PT1 | |
| Igalelo leAnalog 3 | 5 | AN | AN | I-PT-TC | I-PT-TC |
| 7 | V | I | V | V | |
| Igalelo leAnalog 4 | 4 | AN | AN | I-PT-TC | I-PT-TC |
| 6 | V | I | V | V |
* Useto lwefektri oluhlala lukhona
Ukudibanisa kwakhona isilawuli
- Buyisela ibhodi yePCB kwimodyuli kwaye ukhusele isikrufu esiphakathi.
- Okulandelayo, buyisela imodyuli. Layisha isikhokelo sesetyhula kwisilawuli kunye nezikhokelo kwi-Snap-in I/O Module njengoko kubonisiwe ngezantsi.
- Faka uxinzelelo olulinganayo kuzo zonke iikona ezi-4 de uve 'cofa' eyahlukileyo. Imodyuli ifakiwe ngoku. Khangela ukuba onke amacala kunye neekona zilungelelaniswe ngokuchanekileyo.
I-V200-18-E6B Iinkcukacha zobuGcisa
| Inani lamagalelo | 18 (ngamaqela amabini) |
| Uhlobo longeniso | pnp (umthombo) okanye npn (isinki) |
| Ukwahlukaniswa kweGalvanic | |
| Amagalelo edijithali ebhasini | Ewe |
| Amagalelo eDijithali kumagalelo edijithali kwi | Hayi |
| iqela elifanayo | |
| Iqela ukuya kwiqela, amagalelo edijithali | Ewe |
| Igalelo ngegamatage | 24VDC |
| Igalelo voltage | |
| pnp (umthombo) | I-0-5VDC ye-Logic '0' I-17-28.8VDC ye-Logic '1' |
| npn (isinki) | I-17-28.8VDC ye-Logic '0' I-0-5VDC ye-Logic '1' |
| Ungeniso lwangoku | 6mA@24VDC ngamagalelo 4 ukuya ku-17 8.8mA@24VDC ngamagalelo 0 ukuya ku-3 |
| Ixesha lokuphendula | 10mSec eqhelekileyo |
| Amagalelo esantya esiphezulu | Iinkcukacha ezingezantsi ziyasebenza xa ezi galelo zifakwe kwingcingo ukuze zisetyenziswe njengesantya esiphezulu counter input/shaft encoder. Jonga iNqaku loku-1 kunye nelesi-2. |
| Isigqibo | 32-bit |
| Ukuphindaphinda | 10kHz ubuninzi |
| Ubuncinci be-pulse ububanzi | 40μs |
Amanqaku:
- Amagalelo u-0 kunye no-2 anokusebenza njengekhawuntara enesantya esiphezulu okanye njengenxalenye ye-encoder shaft. Kwimeko nganye, iinkcukacha zegalelo lesantya esiphezulu ziyasebenza. Xa isetyenziswa njengengeniso yedijithali eqhelekileyo, iinkcukacha zegalelo eziqhelekileyo ziyasebenza.
- Amagalelo 1 kunye no-3 angenza umsebenzi ngamnye njengokusetwa kwakhona kwekhawunta, okanye njengegalelo eliqhelekileyo ledijithali; kuyo nayiphi na imeko, iinkcukacha zayo zezo zengeniso yedijithali eqhelekileyo. La magalelo nawo anokusetyenziswa njengenxalenye ye-encoder shaft. Kule meko, imilinganiselo yegalelo eliphezulu iyasebenza.
Amanqaku:
Isixhobo sinokulinganisa umthamotage ngaphakathi kuluhlu -5 ukuya 56mV, kwisisombululo 0.01mV. Isixhobo sinokulinganisa umthamo wexabiso elikrwada kwisisombululo se-14-bits (16384). Uluhlu lwezimvo lubonisiwe kolu luhlu lulandelayo:
Itheyibhile 1: Uluhlu lwegalelo le-Thermocouple
| Uhlobo | Uluhlu lobushushu | Ngocingo ANSI (USA) | Umbala I-BS 1843 (eUK) |
| mV | -5 ukuya ku-56nnV | – | – |
| B | 200 ukuya kuma-1820°C (300 ukuya kuma-3276°F) |
+Ngwevu -Bomvu |
+Akukho nanye -Luhlaza |
| E | -200 ukuya kwi-750°C (-328 ukuya ku-1382°F) |
+Violet -Bomvu |
+Brown -Luhlaza |
| J | -200 ukuya kwi-760°C (-328 ukuya ku-1400°F) |
+Mhlophe -Bomvu |
+Yellow -Luhlaza |
| K | -200 ukuya kwi-1250°C (-328 ukuya ku-2282°F) |
+Yellow -Bomvu |
+Brown -Luhlaza |
| N | -200 ukuya kwi-1300°C (-328 ukuya ku-2372°F) |
+Orenji -Bomvu |
+Orenji -Luhlaza |
| R | 0 ukuya kuma-1768°C (32 ukuya kuma-3214°F) |
+Mnyama -Bomvu |
+Mhlophe -Luhlaza |
| S | 0 ukuya kuma-1768°C (32 ukuya kuma-3214°F) |
+Mnyama -Bomvu |
+Mhlophe -Luhlaza |
| T | -200 ukuya kwi-400°C (-328 ukuya ku-752°F) |
+Blue -Bomvu |
+Mhlophe -Luhlaza |
Unitronics
| Okusingqongileyo | IP20 / NEMA1 |
| Ubushushu bokusebenza | 0° ukuya ku-50°C (32° ukuya ku-122°F) |
| Ubushushu bokugcina | -20° ukuya kuma-60°C (-4° ukuya ku-140°F) |
| Ukufuma okuzalanayo (RH) | 10% ukuya kwi-95% (engacondensing) |
| Imilinganiselo (WxHxD) | 138x23x123mm (5.43×0.9×4.84”) |
| Ubunzima | 140g (4.94oz) |
Ulwazi olukolu xwebhu lubonisa iimveliso ngomhla wokushicilela. I-Unitronics inelungelo, ngokuxhomekeke kuyo yonke imithetho esebenzayo, nangaliphi na ixesha, ngokubona kwayo, kwaye ngaphandle kwesaziso, ukuyeka okanye ukutshintsha iimpawu, ukuyila, izixhobo kunye nezinye iinkcukacha zeemveliso zayo, kwaye mhlawumbi ngokusisigxina okanye okwethutyana Ukushiya kwimarike.
Lonke ulwazi olukolu xwebhu lunikelwe “njengoko lunjalo” ngaphandle kwewaranti yalo naluphi na uhlobo, nokuba ichaziwe okanye ichaziwe, kuquka kodwa ingaphelelanga kuzo naziphi na iziqinisekiso ezichaziweyo zokurhwebelana, ukufaneleka kwenjongo ethile, okanye ukungophulwa komthetho. I-Unitronics ayithathi xanduva ngeempazamo okanye ukushiyeka kulwazi olunikwe kolu xwebhu. Akukho siganeko siya kuba noxanduva lwawo nawuphi na umonakalo okhethekileyo, ongalindelekanga, ongathanga ngqo okanye olandelelweyo walo naluphi na uhlobo, okanye nawuphina umonakalo onokuthi uvele ngenxa okanye ngokunxulumene nokusetyenziswa okanye ukwenziwa kolu lwazi.
Amagama orhwebo, iimpawu zentengiso, iilogo kunye neempawu zenkonzo ezithiwe thaca kolu xwebhu, kubandakanywa noyilo lwazo, ziyipropathi ye-Unitronics (1989) (R”G) Ltd. okanye amanye amaqela esithathu kwaye akuvumelekanga ukuzisebenzisa ngaphandle kwemvume ebhaliweyo kwangaphambili. yeUnitronics okanye umntu wesithathu onokuba ngabanini bazo
Amaxwebhu / Izibonelelo
 |
unitronics V200-18-E6B Snap-in-Input-output Module [pdf] Incwadi Yomyalelo V200-18-E6B iModyuli yeNgeniso ye-Snap-in-output, V200-18-E6B, imodyuli ye-Snap-in-Input-Output, imodyuli yegalelo-Igalelo, imodyuli yegalelo, imodyuli |
