I-Interface 3A Series I-Multi Axis Layisha Amaseli Amanuwali

ULWAZI LOKUFAKA

1. Imodeli yesixhumi esibonakalayo 3A Series amaseli okulayisha ama-eksisi amaningi kufanele afakwe endaweni eyisicaba futhi eqinile ngokwanele ukuze angawohloki ngendlela encomekayo lapho elayishiwe.
2. Izinsimbi kufanele zibe yiBanga 8.8 ku-3A60 ukuya ku-3A160 kanye neBanga 10.9 ku-3A300 kanye no-3A400
3. Izinzwa kufanele zifakwe kusetshenziswa izikulufu ezinconyiwe namatorque afakwe kuthebula elingezansi.
4. Izikhonkwane ze-dowel kufanele zisetshenziswe kuzo zonke izindawo ezifakiwe.
5. Ku-3A300 kanye ne-3A400 kufanele okungenani kusetshenziswe izikhonkwane zedowel ezimbili ekugcineni okubukhoma. Kungafika koku-5 kungasetshenziswa.
6. Kuzinzwa ezingu-500N nangaphezulu, ukunamathela okuncane kwe-Loctite 638 noma okufanayo kuyanconywa ezindaweni ezintathu zokukhweza ukuze kuvinjelwe ukushelela.
7. Izinto zokukhweza namapuleti angathinta kuphela inzwa ezindaweni ezikhwezwayo ezibonisiwe.

Imininingwane Yokuqwala

	Imodeli	Umthwalo olinganiselwe/ Amandla	Ubukhulu	Okubalulekile	Ipulatifomu yokulinganisa / Ukuphela Okubukhoma			Stator / Dead End
					Uchungechunge	I-Tightening Torque (Nm)	I-Cylinder pin Hole (mm)	Uchungechunge / Isikulufu Esiyilinda	I-Tightening Torque (Nm)	I-Cylinder pin Hole (mm)
	3A40	±2N ±10N ±20N ±50N	40 mm x 40 mm x 20 mm	ingxube ye-aluminium	intambo yangaphakathi 4x M3x0.5 ukujula okungama-8 mm	1	cha	intambo yangaphakathi 4x M3x0.5 ukujula okungama-8 mm	1	cha
	3A60A	±10N ±20N ±50N ±100N	60 mm x 60 mm x 25 mm	ingxube ye-aluminium	intambo yangaphakathi 4x M3x0.5 ukujula okungama-12 mm	1	2 x Ø2 E7 ukujula okungama-12 mm	2 x DIN EN ISO 4762 M4х0.7 6.8	2	2 x Ø3 E7 ukujula okungama-5 mm
		±200N ±500N		insimbi engagqwali	intambo yangaphakathi 4x M3x0.5 ukujula okungama-12 mm	1	2 x Ø2 E7 ukujula okungama-12 mm	2 x DIN EN ISO 4762 M4х0.7 6.8	2	2 x Ø3 E7 ukujula okungama-5 mm
	3A120	±50N ±100N ±200N ±500N ±1000N	120 mm x 120 mm x 30 mm	ingxube ye-aluminium	Intambo yangaphakathi 4x M6x1 Ukujula 12 mm	10	2 x Ø5 E7 Ukujula 12 mm	4 x DIN EN ISO 4762 M6х1 6.8	10	2 x Ø5 E7 ukujula okungama-3 mm
		±1kN ±2kN ±5kN		insimbi engagqwali	intambo yangaphakathi 4x M6x1 Ukujula 12 mm	15	2 x Ø5 E7 Ukujula 12 mm	4 x DIN EN ISO 4762 M6х1 10.9	15	2 x Ø5 E7 ukujula okungama-3 mm
	3A160	±2kN ±5kN	160 mm x 160 mm x 66 mm	insimbi yensimbi	intambo yangaphakathi 4x M10x1.5 ukujula okungama-15 mm	50	2 x Ø8 H7 ukujula okungama-15 mm	4 x DIN EN ISO 4762 M12х1.75 10.9	80	2 x Ø8 H7 ukujula okungama-5 mm
		±10kN ±20kN ±50kN		insimbi yensimbi	intambo yangaphakathi 4x M10x1.5 ukujula okungama-15 mm	60	2 x Ø8 H7 ukujula okungama-15 mm	4 x DIN EN ISO 4762 M12х1.75 10.9	100	2 x Ø8 H7 ukujula okungama-5 mm
	3A300	±50kN	300 mm x 300 mm x 100 mm	insimbi yensimbi	intambo yangaphakathi 4x M24x3	500	5x Ø25 H7	4 x DIN EN ISO 4762 M24х3 10.9	500	2 x Ø25 H7 ukujula okungama-40 mm
		±100kN ±200kN				800			800
	3A400	±500kN	400 mm x 400 mm x 100 mm	insimbi yensimbi	intambo yangaphakathi 4x M30x3.5	1800	5x Ø30 E7	4 x DIN EN ISO 4762 M30х3.5 10.9	1800	2 x Ø30 E7 ukujula okungama-40 mm

I-Interface Inc.

• 7401 East Buthelezi Drive
• Scottsdale, Arizona 85260 USA

Ukusekela

Ucingo: 480.948.5555
Ifeksi: 480.948.1924
www.interfaceforce.com

Amadokhumenti / Izinsiza

I-Interface 3A Series I-Multi Axis Layisha Amaseli [pdf] Incwadi Yeziqondiso 3A Series, Multi Axis Load Cells, 3A Series Multi Axis Load Cells, Axis Load Cells

Izithenjwa

• Imaniwali yosebenzisayo