Interface 3A Series Multi Axis Load Cells Guide Guide

BAYANIN SHIGA

1. Samfurin mu'amalar 3A Series dole ne a saka sel masu ɗaukar nauyi masu yawa a kan wani saman da yake lebur kuma mai ƙarfi sosai don kada ya lalace a ƙarƙashin kaya.
2. Fasteners yakamata su kasance Grade 8.8 don 3A60 zuwa 3A160 da Grade 10.9 don 3A300 da 3A400
3. Ya kamata a saka na'urori masu auna firikwensin ta hanyar amfani da skru da aka ba da shawarar da magudanar ruwa a cikin teburin da ke ƙasa.
4. Ya kamata a yi amfani da fil ɗin dowel a duk wuraren hawa.
5. Don 3A300 da 3A400 aƙalla fitilun dowel biyu yakamata a yi amfani da su a ƙarshen rayuwa. Ana iya amfani da har zuwa 5.
6. Don na'urori masu auna firikwensin 500N da sama, ana ba da shawarar suturar bakin ciki na Loctite 638 ko makamancin haka akan saman hawa uku don hana zamewa.
7. Matakan hawa da faranti na iya tuntuɓar firikwensin kawai a wuraren da aka nuna.

BAYANAN HAWAN

	Samfura	Ƙarfin ƙima / Ƙarfi	Girma	Kayan abu	Dandalin aunawa / Ƙarshen Rayuwa			Stator / Matattu Ƙarshen
					Zare	Tightening Torque (Nm)	Silinda pin Hole (mm)	Zare / Silinda Screw	Tightening Torque (Nm)	Silinda pin Hole (mm)
	3A40	± 2N ± 10N ± 20N ± 50N	40 mm x 40 mm x mm20 ku	aluminum gami	Zaren ciki 4x M3x0.5 zurfin 8 mm	1	a'a	Zaren ciki 4x M3x0.5 zurfin 8 mm	1	a'a
	3A60 ku	± 10N ± 20N ± 50N ± 100N	60 mm x 60 mm x mm25 ku	aluminum gami	Zaren ciki 4x M3x0.5 zurfin 12 mm	1	2 x Ø2 E7 zurfin 12 mm	2 x DIN EN ISO 4762 M4х0.7 6.8	2	2 x Ø3 E7 zurfin 5 mm
		± 200N ± 500N		bakin karfe	Zaren ciki 4x M3x0.5 zurfin 12 mm	1	2 x Ø2 E7 zurfin 12 mm	2 x DIN EN ISO 4762 M4х0.7 6.8	2	2 x Ø3 E7 zurfin 5 mm
	3A120	± 50N ± 100N ± 200N ± 500N ± 1000N	120 mm x 120 mm x mm30 ku	aluminum gami	Zaren ciki 4x M6x1 Zurfin 12 mm	10	2 x Ø5 E7 Zurfin 12 mm	4 x DIN EN ISO 4762 M6х1 6.8	10	2 x Ø5 E7 zurfin 3 mm
		± 1kN ± 2kN ± 5kN		bakin karfe	Zaren ciki 4x M6x1 Zurfin 12 mm	15	2 x Ø5 E7 Zurfin 12 mm	4 x DIN EN ISO 4762 M6х1 10.9	15	2 x Ø5 E7 zurfin 3 mm
	3A160	± 2kN ± 5kN	160 mm x 160 mm x mm66 ku	kayan aiki karfe	Zaren ciki 4x M10x1.5 zurfin 15 mm	50	2 x Ø8 H7 zurfin 15 mm	4 x DIN EN ISO 4762 M12х1.75 10.9	80	2 x Ø8 H7 zurfin 5 mm
		± 10kN ± 20kN ± 50kN		kayan aiki karfe	Zaren ciki 4x M10x1.5 zurfin 15 mm	60	2 x Ø8 H7 zurfin 15 mm	4 x DIN EN ISO 4762 M12х1.75 10.9	100	2 x Ø8 H7 zurfin 5 mm
	3A300	± 50kN	300 mm x 300 mm x mm100 ku	kayan aiki karfe	Zaren ciki 4x M24x3	500	5 x Ø25 H7	4 x DIN EN ISO 4762 M24х3 10.9	500	2 x Ø25 H7 zurfin 40 mm
		± 100kN ± 200kN				800			800
	3A400	± 500kN	400 mm x 400 mm x mm100 ku	kayan aiki karfe	Zaren ciki 4x M30x3.5	1800	5x Ø30 E7	4 x DIN EN ISO 4762 M30х3.5 10.9	1800	2 x Ø30 E7 zurfin 40 mm

Interface Inc.

• 7401 Gabas Buttherus Drive
• Scottsdale, Arizona 85260 Amurka

Taimako

Waya: 480.948.5555
Fax: 480.948.1924
www.interfaceforce.com

Takardu / Albarkatu

Interface 3A Series Multi axis Load Sel [pdf] Jagoran Jagora 3A Series, Multi Axis Load Sel, 3A Series Multi Axis Load Sel, Axis Load Sel

Magana

• Manual mai amfani