eSSL JS-36E 安全独立门禁控制器用户手册

JS-36E 安全独立门禁机

规格

操作量tage: DC12-24V

工作电流: 100毫安

工作湿度: 0%-95%

待机电流: 60毫安

工作温度: -40至60℃

Access Ways: Fingerprint, card, code, multiple
combination methods, mobile phone App (Optional)

产品使用说明

安装

  1. Remove the back cover form the keypad using the supplied
    special screw drive.
  2. Drill 2 holes on the wall for the self-tapping screw and 1 hole
    用于电缆。
  3. Put the supplied rubber bungs into the two holes.
  4. Fix the back cover firmly on the wall with 2 self-tapping
    螺丝。
  5. 将电缆穿过电缆孔。
  6. Attach the keypad to the back cover. (Refer to figure for
    guidance)

接线

颜色标记 描述
Pink Bell-A Door bell button on one end

系統設定

  1. Master code #: Enter the programming mode,
    default factory master code is 999999.
  2. 系统设置:
  • Change Master code: Enter 6 to 8 digits new code, repeat new
    代码。
  • Reset to Factory Default #:
  • 存储空间

    1. 添加用户:
      1. Add card user: Input ID number, read card or input Card
        不。

    常见问题 (FAQ)

    问:如何将设备重置为出厂默认设置?

    A: To reset to factory default, enter the programming mode and
    use the specified code for resetting.

    问:设备的工作温度范围是多少?

    答:该设备可以在-40°C到-XNUMX°C的温度范围内工作
    60℃。


    “`

    JS-36E User Manual
    使用本机前请仔细阅读手册。

    1. 简介
    This series’s product is a new generation on multifunctional standalone access control.It adopts new ARM core 32-bit microprocessor design, which is powerful, stable and reliable . It contains reader mode and standalone access control mode etc.. It’s widely applied to different occasions, such as office, residential communities, villa, bank and prison etc..

    2. 特点
    卡类型
    Keypad Characteristic Output Way
    Access Way Admin Card User Capacity Unlock Signal Alarm Output

    Read 125KHz Card and HID Card(Optional) Read 13.56MHz Mifare card and CPU card(Optional) Capacitive touch keypad Contain reader mode, the transmission format could be adjusted by user Fingerprint , card,code or multiple combination methods, mobile phone App (Optional Support admin add card and admin delete card 10000 NO, NC, COM output using relay Use MOS tube output to directly drive the alarm (optional)

    3.技术规格

    操作量tage: DC12-24V Operating Current100mA
    工作湿度:0%-95%

    待机电流 60mA
    Operating Temperature:-40-60
    Access waysFingerprint, card, code, multiple combination methods, mobile phone App (Optional

    01

    4.安装
    使用提供的专用螺丝刀卸下键盘后盖
    Drill 2 holes on the wall for the self-tapping screw and 1 hole for the cable Put the supplied rubber bungs to into the two holes Fix the back cover firmly on the wall with 2 self tapping screws Thread the cable through the cable hole Attached the keypad to the back cover.(See the figure right)

    5.接线

    颜色标记

    描述

    Pink Bell-A

    门铃按钮在末端

    Pink Bell-B

    另一端的门铃按钮

    Green D0 White D1

    Wiegand input (Wiegand output as reader mode) Wiegabd inputWiegand output as reader mode

    Grey Alarm

    报警信号MOS管漏极输出端

    Yellow Open(BEEP) Exit button input end(Beeper input as reader mode)

    Brown DIN(LED)

    门磁开关输入端(读卡器模式LED控制输入)

    红色的

    +12 伏

    正电源

    黑色GND

    负电源

    蓝色 NO

    继电器无端

    Purple COM

    继电器 COM 端

    Orange NC

    继电器NC端

    02

    6. 图表
    1. Special power supply diagram

    Electric Rim Lock

    Electritc mortise lock Magnetic lock
    GND PUSH GND +12V NO NC

    交流220V

    退出按钮

    Red Black Purple Blue Yelow

    03

    6.2 阅读器模式

    红色 黑色 绿色 白色
    04

    7.系统设置

    Master code # Enter the programming mode,default factory master code is 999999.

    0.系统设置

    0.Change Master code

    Enter 6 to 8 digits new code # Repeat New code #

    1.Register Add Admin 2.Register Delete Admin

    Read card /input a fingerprint Read card /input a fingerprint

    3.Working Mode 4.Data Backup 5.WiFi matching

    0 #Reader mode) 1# (Standalone access control mode) 2# (Relay toggle mode)

    0 #Data backup output) 1# (Data backup input)

    # ……

    (The Green wire and white wire of machine connects correspondingly)

    7.Reset to Factory Default #

    8.Storage Space

    1.Add Users

    1.Add card user

    Input ID number read card or Input Card NO. #

    2.Add PIN code user

    Input ID number setting 4-6 digital door open code #

    3.Add Fingerprint user

    Input ID number press a fingerprint twice

    4.Add Fingerprint +Card user Read user card press fingerprint twice (Note: unregistered new fingerprint)

    5.Add conductive number Card Input ID number read card or input card number # input user quantity # 05

    2.Delete Users

    0.Delete all user

    # (Notice: admin code won’t be deleted. )

    1.Delete user ID number

    Input ID number

    #

    (Notice : Delete pointed card , fingerprint or PIN code users by user ID number. )

    2.Delete Card user

    Read card or Input Card number #

    3.Delete fingerprint user Press Fingerprint

    4.Delete temporary code # (Notice : Delete the temporary code issued by the mobile phone App.)

    3.Door Open Mode

    1.Door Open Way

    1. Forbidden (can’t open door) #
    2.Entry by code only # 3.Entry by card only # 4.Entry by card(fingerprint )+code only #
    5. Entry by card,code or fingerprint #
    6.Entry by fingerprint only #
    7. Entry by card+fingerprint #
    8.Entry by multiple users #

    2.Entry by multiple users Unlock by 1-10 users #

    06

    4.时间设置

    1.Unlock time

    输入0-300

    # (Time range 0~300S, Factory default: 5S)

    2.Alarm output time Input 0-99 # (Time range 0~99S, Factory default: 0S)

    3.Date & time setting Input date # Input time #

    5.Card Reader Model setting

    1.Device ID

    0-255 Device ID #

    2.Wiegand output

    WG26-58 #

    3.Keyboard format 0 #4 bit wg output) 1# (8 bit inverse code) 2# (virtual card number)

    6.基本设置

    1.Alarm model

    0# (Forbidden) 1# (Alarm) 2# (Locked)

    2.Keypad LED light 0~99 # Can set 0-99sFactory default 10S)

    3. 音量

    0# (close) 1# (low) 2# (High)

    4.language

    0# (Chinese) 1# (English)

    07

    8.恢复出厂设置
    When forget the administrator password,reset it to the factory default setting,The default administrator password is “999999” Method 1: Power off, power on, screen lights on,press the # key,The display will shows default settings is successful. Method 2: Power off,press the exit button continously,power on, The display will shows default settings is successful.
    Method 3: 0.system setting 7.Reset factory default setting #
    9. Reader mode switch to standalone access control mode When the device is under card reader mode, long press * to switch to standalone access control mode
    10. Cancel alarm
    Read admin card or read valid user card or valid fingerprint or admin password # Note: When alarm occurs, the buzzer will sound “woo, woo,…” and the alarm can be canceled by reading the valid card or inputting admin password.

    11。装箱清单

    Item Device User Manual Self-tapping screwdriver Rubber plug Star screwdriver Star screws

    规格
    4mm×25 mm 6mm×28 mm 20mm×60mm 3mm×5mm

    数量

    评论

    1

    1

    2

    用于安装和固定

    2

    用于安装和固定

    1

    特殊目的

    1

    For fixing the front cover and

    封底

    Note: *Please do not repair the machine without permission. If there is any problem, please return it to the manufacturer for repair. *Before installation, if you want to drill holes, please carefully check the hidden wires or conduits to prevent unnecessary trouble caused by drilling the hidden wires when drilling. Use safety glasses when drilling or fixing wire clips. *If the product is upgraded, the instructions may be different without prior notice.

    08

    12.WIFI功能

    选修的

    1 Scan the QR code by your mobile phone to download the Tuya Smart APP or search the Tuya Smart APP to download APP by mobile phone application market (Figure 1)

    2 Open the APP, click the “+”at the upper right corner, Add Device (Figure 2) (Note: When searching for devices, turn on the

    Bluetooth and location services functions firstly)

    笔记:

    At the same time, turn on the “wireless function on the access control.Press

    pairing” Admin

    密码

    # 0. System settings

    # 5. WIFI pairing #

    3 Enter the WIFI password, then click Next. (Figure 3)

    扫描二维码
    TuyaSmart Search”TuyaSmart
    下载
    TuyaSmart Search”TuyaSmart”
    下载
    Search TuyaSmart to download APP Figure 1

    图 2

    图3

    09

    4 Wait for successful connection,click Done

    AC

    AC

    5 Set remote unlock,click setting,open remote unlock setting
    AC

    10

    6 Press to unlock
    AC

    7 Member management Administrator Add fingerprint start adding input fingerprint twice add successfully,input name,click Done.

    ********

    ********

    11

    8

    Add code user by clicking add temporary code periodically, and input 6 digits code or click randomly generated, then

    input code name, and click save.

    9

    Add card by clicking start add, swiping one card within 60 seconds, add card successfully, then

    fill card name and click “done”.

    12

    Add ordinary user by clicking ordinary member, 10 then click at the upper right corner “+”, then input
    the related information and click “next step”.
    13

    11 Add temporary code, click `once”, input code name, click “save offline code”, done.
    AC
    14

    12 Query unlock records
    AC

    13 Settings: access ways, alarm time, volume, language.
    AC

    Click hereto check the unlock records 15

    文件/资源

    eSSL JS-36E Security Standalone Access Control [pdf] 用户手册
    JS-36E Security Standalone Access Control, JS-36E, Security Standalone Access Control, Standalone Access Control, Access Control

    参考

    发表评论

    您的电子邮件地址不会被公开。 必填字段已标记 *