eSSL JS-36E سيڪيورٽي اسٽينڊ اڪيلو رسائي ڪنٽرول يوزر مينوئل

1. تعارف
This series’s product is a new generation on multifunctional standalone access control.It adopts new ARM core 32-bit microprocessor design, which is powerful, stable and reliable . It contains reader mode and standalone access control mode etc.. It’s widely applied to different occasions, such as office, residential communities, villa, bank and prison etc..

2. خاصيتون
ڪارڊ جو قسم
Keypad Characteristic Output Way
Access Way Admin Card User Capacity Unlock Signal Alarm Output

Read 125KHz Card and HID Card(Optional) Read 13.56MHz Mifare card and CPU card(Optional) Capacitive touch keypad Contain reader mode, the transmission format could be adjusted by user Fingerprint , card,code or multiple combination methods, mobile phone App (Optional Support admin add card and admin delete card 10000 NO, NC, COM output using relay Use MOS tube output to directly drive the alarm (optional)

3. ٽيڪنيڪل وضاحتون

آپريٽنگ جلدtage: DC12-24V Operating Current100mA
آپريٽنگ نمي: 0%-95%

اسٽينڊ بائي ڪرنٽ 60mA
Operating Temperature:-40-60
Access waysFingerprint, card, code, multiple combination methods, mobile phone App (Optional

4. تنصيب
فراهم ڪيل خاص اسڪرو ڊرائيو استعمال ڪندي ڪي پيڊ مان پوئين ڍڪ هٽايو.
Drill 2 holes on the wall for the self-tapping screw and 1 hole for the cable Put the supplied rubber bungs to into the two holes Fix the back cover firmly on the wall with 2 self tapping screws Thread the cable through the cable hole Attached the keypad to the back cover.(See the figure right)

5. وائرنگ

رنگ جا نشان

وصف

Pink Bell-A

دروازي جي گھنٽي جو بٽڻ آخر ۾

Pink Bell-B

دروازي جي گھنٽي جو بٽڻ ٻئي پاسي

Green D0 White D1

Wiegand input (Wiegand output as reader mode) Wiegabd inputWiegand output as reader mode

Grey Alarm

الارم سگنل MOS ٽيوب ڊرين آئوٽ پُٽ آخر

Yellow Open(BEEP) Exit button input end(Beeper input as reader mode)

Brown DIN(LED)

دروازو سينسر سوئچ ان پٽ ان پٽ (ڪارڊ ريڊر موڊ LED ڪنٽرول ان پٽ)

ڳاڙهو

+12V

مثبت توانائي جي فراهمي

ڪارو GND

منفي توانائي جي فراهمي

نيرو NO

رلي NO آخر

Purple COM

رلي COM ختم

Orange NC

رلي NC ختم

6. خاڪو
1. Special power supply diagram

Electric Rim Lock

Electritc mortise lock Magnetic lock
GND PUSH GND +12V NO NC

AC 220V

نڪرڻ واري بٽڻ

Red Black Purple Blue Yelow

6.2 ريڊر موڊ

ڳاڙهو ڪارو سائو اڇو
04

7. سسٽم سيٽنگ

Master code # Enter the programming mode,default factory master code is 999999.

0. سسٽم سيٽنگ

0.Change Master code

Enter 6 to 8 digits new code # Repeat New code #

1.Register Add Admin 2.Register Delete Admin

Read card /input a fingerprint Read card /input a fingerprint

3.Working Mode 4.Data Backup 5.WiFi matching

0 #Reader mode) 1# (Standalone access control mode) 2# (Relay toggle mode)

0 #Data backup output) 1# (Data backup input)

# ……

(The Green wire and white wire of machine connects correspondingly)

7.Reset to Factory Default #

8.Storage Space

1.Add Users

1.Add card user

Input ID number read card or Input Card NO. #

2.Add PIN code user

Input ID number setting 4-6 digital door open code #

3.Add Fingerprint user

Input ID number press a fingerprint twice

4.Add Fingerprint +Card user Read user card press fingerprint twice (Note: unregistered new fingerprint)

5.Add conductive number Card Input ID number read card or input card number # input user quantity # 05

2.Delete Users

0.Delete all user

# (Notice: admin code won’t be deleted. )

1.Delete user ID number

Input ID number

(Notice : Delete pointed card , fingerprint or PIN code users by user ID number. )

2.Delete Card user

Read card or Input Card number #

3.Delete fingerprint user Press Fingerprint

4.Delete temporary code # (Notice : Delete the temporary code issued by the mobile phone App.)

3.Door Open Mode

1.Door Open Way

1. Forbidden (can’t open door) #
2.Entry by code only # 3.Entry by card only # 4.Entry by card(fingerprint )+code only #
5. Entry by card,code or fingerprint #
6.Entry by fingerprint only #
7. Entry by card+fingerprint #
8.Entry by multiple users #

2.Entry by multiple users Unlock by 1-10 users #

4. وقت جي جوڙجڪ

1.Unlock time

انپٽ 0-300

# (Time range 0~300S, Factory default: 5S)

2.Alarm output time Input 0-99 # (Time range 0~99S, Factory default: 0S)

3.Date & time setting Input date # Input time #

5.Card Reader Model setting

1.Device ID

0-255 Device ID #

2.Wiegand output

WG26-58 #

3.Keyboard format 0 #4 bit wg output) 1# (8 bit inverse code) 2# (virtual card number)

6. بنيادي سيٽنگون

1.Alarm model

0# (Forbidden) 1# (Alarm) 2# (Locked)

2.Keypad LED light 0~99 # Can set 0-99sFactory default 10S)

3. حجم

0# (close) 1# (low) 2# (High)

4.language

0# (Chinese) 1# (English)

8. فيڪٽري ڊفالٽ تي ري سيٽ ڪريو
When forget the administrator password,reset it to the factory default setting,The default administrator password is “999999” Method 1: Power off, power on, screen lights on,press the # key,The display will shows default settings is successful. Method 2: Power off,press the exit button continously,power on, The display will shows default settings is successful.
Method 3: 0.system setting 7.Reset factory default setting #
9. Reader mode switch to standalone access control mode When the device is under card reader mode, long press * to switch to standalone access control mode
10. Cancel alarm
Read admin card or read valid user card or valid fingerprint or admin password # Note: When alarm occurs, the buzzer will sound “woo, woo,…” and the alarm can be canceled by reading the valid card or inputting admin password.

11.Packing لسٽ

Item Device User Manual Self-tapping screwdriver Rubber plug Star screwdriver Star screws

تفصيل
4mm×25 mm 6mm×28 mm 20mm×60mm 3mm×5mm

مقدار

تبصرو

لڳائڻ ۽ fixin لاء

لڳائڻ ۽ فڪسنگ لاء

خاص مقصد

For fixing the front cover and

پوئين ڍڪ

Note: *Please do not repair the machine without permission. If there is any problem, please return it to the manufacturer for repair. *Before installation, if you want to drill holes, please carefully check the hidden wires or conduits to prevent unnecessary trouble caused by drilling the hidden wires when drilling. Use safety glasses when drilling or fixing wire clips. *If the product is upgraded, the instructions may be different without prior notice.

12. وائي فائي فنڪشن

اختياري

1 Scan the QR code by your mobile phone to download the Tuya Smart APP or search the Tuya Smart APP to download APP by mobile phone application market (Figure 1)

2 Open the APP, click the “+”at the upper right corner, Add Device (Figure 2) (Note: When searching for devices, turn on the

Bluetooth and location services functions firstly)

نوٽ:

At the same time, turn on the “wireless function on the access control.Press

pairing” Admin

پاسورڊ

# 0. System settings

# 5. WIFI pairing #

3 Enter the WIFI password, then click Next. (Figure 3)

QR ڪوڊ اسڪين ڪريو
TuyaSmart Search”TuyaSmart
ڊائون لوڊ
TuyaSmart Search”TuyaSmart”
ڊائون لوڊ
Search TuyaSmart to download APP Figure 1

شڪل 2

شڪل 3

4 Wait for successful connection,click Done

5 Set remote unlock,click setting,open remote unlock setting
AC

6 Press to unlock
AC

7 Member management Administrator Add fingerprint start adding input fingerprint twice add successfully,input name,click Done.

********

Add code user by clicking add temporary code periodically, and input 6 digits code or click randomly generated, then

input code name, and click save.

Add card by clicking start add, swiping one card within 60 seconds, add card successfully, then

fill card name and click “done”.

Add ordinary user by clicking ordinary member, 10 then click at the upper right corner “+”, then input
the related information and click “next step”.
13

11 Add temporary code, click `once”, input code name, click “save offline code”, done.
AC
14

12 Query unlock records
AC

13 Settings: access ways, alarm time, volume, language.
AC

Click hereto check the unlock records 15

دستاويز / وسيلا

eSSL JS-36E Security Standalone Access Control [pdf] استعمال ڪندڙ دستياب
JS-36E Security Standalone Access Control, JS-36E, Security Standalone Access Control, Standalone Access Control, Access Control

حوالو

استعمال ڪندڙ دستي

eSSL JS-36E سيڪيورٽي اسٽينڊ اڪيلو رسائي ڪنٽرول يوزر مينوئل

JS-36E سيڪيورٽي اسٽينڊلون رسائي ڪنٽرول

وضاحتون

پيداوار جي استعمال جون هدايتون

تنصيب

وائرنگ

سسٽم سيٽنگ

اسٽوريج جي جاء

اڪثر پڇيا ويندڙ سوال (FAQ)

عبرت: ڊوائيس کي فيڪٽري ڊفالٽ سيٽنگون ڪيئن ري سيٽ ڪجي؟

عبرت: ڊوائيس جي آپريٽنگ گرمي جي حد ڇا آهي؟

دستاويز / وسيلا

حوالو

تبصرو ڇڏي ڏيو

رد ڪريو جواب