eSSL JS-36E ຄູ່ມືຜູ້ໃຊ້ການຄວບຄຸມການເຂົ້າເຖິງແບບຢືນຢູ່ຄົນດຽວ

1. ບົດແນະນຳ
This series’s product is a new generation on multifunctional standalone access control.It adopts new ARM core 32-bit microprocessor design, which is powerful, stable and reliable . It contains reader mode and standalone access control mode etc.. It’s widely applied to different occasions, such as office, residential communities, villa, bank and prison etc..

2. ຄຸນສົມບັດ
ປະເພດບັດ
Keypad Characteristic Output Way
Access Way Admin Card User Capacity Unlock Signal Alarm Output

Read 125KHz Card and HID Card(Optional) Read 13.56MHz Mifare card and CPU card(Optional) Capacitive touch keypad Contain reader mode, the transmission format could be adjusted by user Fingerprint , card,code or multiple combination methods, mobile phone App (Optional Support admin add card and admin delete card 10000 NO, NC, COM output using relay Use MOS tube output to directly drive the alarm (optional)

3. ເຕັກນິກວິຊາສະເພາະ

ການດໍາເນີນງານ Voltage: DC12-24V Operating Current100mA
ຄວາມຊຸ່ມຊື້ນ: 0%-95%

Standby Current 60mA
Operating Temperature:-40-60
Access waysFingerprint, card, code, multiple combination methods, mobile phone App (Optional

4. ການຕິດຕັ້ງ
ເອົາຝາປິດຫຼັງອອກເປັນປຸ່ມກົດໂດຍໃຊ້ສະກູດພິເສດທີ່ໃຫ້ມາ
Drill 2 holes on the wall for the self-tapping screw and 1 hole for the cable Put the supplied rubber bungs to into the two holes Fix the back cover firmly on the wall with 2 self tapping screws Thread the cable through the cable hole Attached the keypad to the back cover.(See the figure right)

5. ສາຍໄຟຟ້າ

ເຄື່ອງໝາຍສີ

ລາຍລະອຽດ

Pink Bell-A

ປຸ່ມກະດິ່ງປະຕູຢູ່ປາຍ

Pink Bell-B

ປຸ່ມກະດິ່ງປະຕູຢູ່ປາຍອື່ນ

Green D0 White D1

Wiegand input (Wiegand output as reader mode) Wiegabd inputWiegand output as reader mode

Grey Alarm

ສັນຍານເຕືອນໄພ MOS tube drain output

Yellow Open(BEEP) Exit button input end(Beeper input as reader mode)

Brown DIN(LED)

ເຊັນເຊີປະຕູປຸ່ມປ້ອນເຂົ້າທ້າຍ (ໂໝດເຄື່ອງອ່ານບັດ LED ຄວບຄຸມອິນພຸດ)

ສີແດງ

+12V

ການສະຫນອງພະລັງງານໃນທາງບວກ

GND ສີດໍາ

ການສະ ໜອງ ພະລັງງານລົບ

ສີຟ້າ NO

Relay ບໍ່ມີສິ້ນສຸດ

Purple COM

Relay COM ສິ້ນສຸດ

Orange NC

Relay NC ສິ້ນສຸດ

6. ແຜນວາດ
1. Special power supply diagram

Electric Rim Lock

Electritc mortise lock Magnetic lock
GND PUSH GND +12V NO NC

AC 220V

ປຸ່ມອອກ

Red Black Purple Blue Yelow

6.2 ໂໝດເຄື່ອງອ່ານ

ສີແດງດຳ ສີຂຽວ ສີຂາວ
04

7. ການຕັ້ງຄ່າລະບົບ

Master code # Enter the programming mode,default factory master code is 999999.

0. ການຕັ້ງຄ່າລະບົບ

0.Change Master code

Enter 6 to 8 digits new code # Repeat New code #

1.Register Add Admin 2.Register Delete Admin

Read card /input a fingerprint Read card /input a fingerprint

3.Working Mode 4.Data Backup 5.WiFi matching

0 #Reader mode) 1# (Standalone access control mode) 2# (Relay toggle mode)

0 #Data backup output) 1# (Data backup input)

# ……

(The Green wire and white wire of machine connects correspondingly)

7.Reset to Factory Default #

8.Storage Space

1.Add Users

1.Add card user

Input ID number read card or Input Card NO. #

2.Add PIN code user

Input ID number setting 4-6 digital door open code #

3.Add Fingerprint user

Input ID number press a fingerprint twice

4.Add Fingerprint +Card user Read user card press fingerprint twice (Note: unregistered new fingerprint)

5.Add conductive number Card Input ID number read card or input card number # input user quantity # 05

2.Delete Users

0.Delete all user

# (Notice: admin code won’t be deleted. )

1.Delete user ID number

Input ID number

(Notice : Delete pointed card , fingerprint or PIN code users by user ID number. )

2.Delete Card user

Read card or Input Card number #

3.Delete fingerprint user Press Fingerprint

4.Delete temporary code # (Notice : Delete the temporary code issued by the mobile phone App.)

3.Door Open Mode

1.Door Open Way

1. Forbidden (can’t open door) #
2.Entry by code only # 3.Entry by card only # 4.Entry by card(fingerprint )+code only #
5. Entry by card,code or fingerprint #
6.Entry by fingerprint only #
7. Entry by card+fingerprint #
8.Entry by multiple users #

2.Entry by multiple users Unlock by 1-10 users #

4.ຕັ້ງເວລາ

1.Unlock time

ການປ້ອນຂໍ້ມູນ 0-300

# (Time range 0~300S, Factory default: 5S)

2.Alarm output time Input 0-99 # (Time range 0~99S, Factory default: 0S)

3.Date & time setting Input date # Input time #

5.Card Reader Model setting

1.Device ID

0-255 Device ID #

2.Wiegand output

WG26-58 #

3.Keyboard format 0 #4 bit wg output) 1# (8 bit inverse code) 2# (virtual card number)

6.ການຕັ້ງຄ່າພື້ນຖານ

1.Alarm model

0# (Forbidden) 1# (Alarm) 2# (Locked)

2.Keypad LED light 0~99 # Can set 0-99sFactory default 10S)

3.ປະລິມານ

0# (close) 1# (low) 2# (High)

4.language

0# (Chinese) 1# (English)

8.ຣີເຊັດເປັນຄ່າເລີ່ມຕົ້ນຈາກໂຮງງານ
When forget the administrator password,reset it to the factory default setting,The default administrator password is “999999” Method 1: Power off, power on, screen lights on,press the # key,The display will shows default settings is successful. Method 2: Power off,press the exit button continously,power on, The display will shows default settings is successful.
Method 3: 0.system setting 7.Reset factory default setting #
9. Reader mode switch to standalone access control mode When the device is under card reader mode, long press * to switch to standalone access control mode
10. Cancel alarm
Read admin card or read valid user card or valid fingerprint or admin password # Note: When alarm occurs, the buzzer will sound “woo, woo,…” and the alarm can be canceled by reading the valid card or inputting admin password.

11.ລາຍການບັນຈຸ

Item Device User Manual Self-tapping screwdriver Rubber plug Star screwdriver Star screws

ຂໍ້ມູນຈໍາເພາະ
4mm×25 mm 6mm×28 mm 20mm×60mm 3mm×5mm

ຈຳນວນ

ຂໍ້ສັງເກດ

ສໍາລັບການຕິດຕັ້ງແລະ fixin

ສໍາລັບການຕິດຕັ້ງແລະການແກ້ໄຂ

ຈຸດປະສົງພິເສດ

For fixing the front cover and

ຝາຫຼັງ

Note: *Please do not repair the machine without permission. If there is any problem, please return it to the manufacturer for repair. *Before installation, if you want to drill holes, please carefully check the hidden wires or conduits to prevent unnecessary trouble caused by drilling the hidden wires when drilling. Use safety glasses when drilling or fixing wire clips. *If the product is upgraded, the instructions may be different without prior notice.

12. ໜ້າ ທີ່ WIFI

ທາງເລືອກ

1 Scan the QR code by your mobile phone to download the Tuya Smart APP or search the Tuya Smart APP to download APP by mobile phone application market (Figure 1)

2 Open the APP, click the “+”at the upper right corner, Add Device (Figure 2) (Note: When searching for devices, turn on the

Bluetooth and location services functions firstly)

ໝາຍເຫດ:

At the same time, turn on the “wireless function on the access control.Press

pairing” Admin

ລະຫັດຜ່ານ

# 0. System settings

# 5. WIFI pairing #

3 Enter the WIFI password, then click Next. (Figure 3)

ສະແກນລະຫັດ QR
TuyaSmart Search”TuyaSmart
ດາວໂຫຼດ
TuyaSmart Search”TuyaSmart”
ດາວໂຫຼດ
Search TuyaSmart to download APP Figure 1

ຮູບ 2

ຮູບ3

4 Wait for successful connection,click Done

5 Set remote unlock,click setting,open remote unlock setting
AC

6 Press to unlock
AC

7 Member management Administrator Add fingerprint start adding input fingerprint twice add successfully,input name,click Done.

********

Add code user by clicking add temporary code periodically, and input 6 digits code or click randomly generated, then

input code name, and click save.

Add card by clicking start add, swiping one card within 60 seconds, add card successfully, then

fill card name and click “done”.

Add ordinary user by clicking ordinary member, 10 then click at the upper right corner “+”, then input
the related information and click “next step”.
13

11 Add temporary code, click `once”, input code name, click “save offline code”, done.
AC
14

12 Query unlock records
AC

13 Settings: access ways, alarm time, volume, language.
AC

Click hereto check the unlock records 15

ເອກະສານ / ຊັບພະຍາກອນ

eSSL JS-36E Security Standalone Access Control [pdf] ຄູ່ມືຜູ້ໃຊ້
JS-36E Security Standalone Access Control, JS-36E, Security Standalone Access Control, Standalone Access Control, Access Control

ເອກະສານອ້າງອີງ

ຄູ່ມືຜູ້ໃຊ້

eSSL JS-36E ຄູ່ມືຜູ້ໃຊ້ການຄວບຄຸມການເຂົ້າເຖິງແບບຢືນຢູ່ຄົນດຽວ

ການຄວບຄຸມການເຂົ້າເຖິງຄວາມປອດໄພ JS-36E ແບບດ່ຽວ

ຂໍ້ມູນຈໍາເພາະ

ຄໍາແນະນໍາການນໍາໃຊ້ຜະລິດຕະພັນ

ການຕິດຕັ້ງ

ສາຍໄຟ

ການຕັ້ງຄ່າລະບົບ

ພື້ນທີ່ເກັບຮັກສາ

ຄຳຖາມທີ່ຖາມເລື້ອຍໆ (FAQ)

ຖາມ: ຈະຣີເຊັດອຸປະກອນເປັນຄ່າເລີ່ມຕົ້ນຂອງໂຮງງານແນວໃດ?

Q: ຊ່ວງອຸນຫະພູມປະຕິບັດງານຂອງອຸປະກອນແມ່ນຫຍັງ?

ເອກະສານ / ຊັບພະຍາກອນ

ເອກະສານອ້າງອີງ

ອອກຄໍາເຫັນ

ຍົກເລີກການຕອບ