نظام التحكم في الوصول المستقل الأمني JS-36E
“
تحديد
حجم التشغيلtage: تيار مستمر 12-24 فولت
تيار التشغيل: 100 مللي أمبير
رطوبة التشغيل: 0%-95%
الاستعداد الحالي: 60 مللي أمبير
درجة حرارة التشغيل: -40-60 درجة مئوية
Access Ways: Fingerprint, card, code, multiple
combination methods, mobile phone App (Optional)
تعليمات استخدام المنتج
تثبيت
- Remove the back cover form the keypad using the supplied
special screw drive. - Drill 2 holes on the wall for the self-tapping screw and 1 hole
للكابل. - Put the supplied rubber bungs into the two holes.
- Fix the back cover firmly on the wall with 2 self-tapping
مسامير. - مرر الكبل من خلال فتحة الكبل.
- Attach the keypad to the back cover. (Refer to figure for
guidance)
الأسلاك
علامات اللون | وصف |
---|---|
Pink Bell-A | Door bell button on one end |
إعدادات النظام
- Master code #: Enter the programming mode,
default factory master code is 999999. - اعدادات النظام:
- Change Master code: Enter 6 to 8 digits new code, repeat new
شفرة.
مساحة التخزين
- إضافة مستخدمين:
- Add card user: Input ID number, read card or input Card
لا.
الأسئلة الشائعة
س: كيفية إعادة تعيين الجهاز إلى إعدادات المصنع الافتراضية؟
A: To reset to factory default, enter the programming mode and
use the specified code for resetting.
س: ما هو نطاق درجة حرارة تشغيل الجهاز؟
أ: يمكن تشغيل الجهاز في نطاق درجة حرارة يتراوح من -40 درجة مئوية إلى
60 درجة مئوية.
"
JS-36E User Manual
يرجى قراءة الدليل بعناية قبل استخدام هذه الوحدة.
1. المقدمة
This series’s product is a new generation on multifunctional standalone access control.It adopts new ARM core 32-bit microprocessor design, which is powerful, stable and reliable . It contains reader mode and standalone access control mode etc.. It’s widely applied to different occasions, such as office, residential communities, villa, bank and prison etc..
2. المميزات
نوع البطاقة
Keypad Characteristic Output Way
Access Way Admin Card User Capacity Unlock Signal Alarm Output
Read 125KHz Card and HID Card(Optional) Read 13.56MHz Mifare card and CPU card(Optional) Capacitive touch keypad Contain reader mode, the transmission format could be adjusted by user Fingerprint , card,code or multiple combination methods, mobile phone App (Optional Support admin add card and admin delete card 10000 NO, NC, COM output using relay Use MOS tube output to directly drive the alarm (optional)
3. المواصفات الفنية
حجم التشغيلtage: DC12-24V Operating Current100mA
رطوبة التشغيل: 0%-95%
الاستعداد الحالي 60mA
Operating Temperature:-40-60
Access waysFingerprint, card, code, multiple combination methods, mobile phone App (Optional
01
4. التثبيت
قم بإزالة الغطاء الخلفي من لوحة المفاتيح باستخدام محرك المسمار الخاص المرفق
Drill 2 holes on the wall for the self-tapping screw and 1 hole for the cable Put the supplied rubber bungs to into the two holes Fix the back cover firmly on the wall with 2 self tapping screws Thread the cable through the cable hole Attached the keypad to the back cover.(See the figure right)
5. الأسلاك
علامات اللون
وصف
Pink Bell-A
زر جرس الباب في النهاية
Pink Bell-B
زر جرس الباب على الطرف الآخر
Green D0 White D1
Wiegand input (Wiegand output as reader mode) Wiegabd inputWiegand output as reader mode
Grey Alarm
إشارة إنذار نهاية إخراج أنبوب MOS
Yellow Open(BEEP) Exit button input end(Beeper input as reader mode)
Brown DIN(LED)
نهاية إدخال مفتاح مستشعر الباب (إدخال التحكم في وضع قارئ البطاقات)
أحمر
+12 فولت
مصدر طاقة إيجابي
GND الأسود
مصدر طاقة سلبي
أزرق لا
لا نهاية التتابع
Purple COM
نهاية تتابع COM
Orange NC
نهاية التتابع NC
02
6. الرسم التخطيطي
1. Special power supply diagram
Electric Rim Lock
Electritc mortise lock Magnetic lock
GND PUSH GND +12V NO NC
تيار متردد 220 فولت
زر الخروج
Red Black Purple Blue Yelow
03
6.2 وضع القارئ
أحمر أسود أخضر أبيض
04
7.إعدادات النظام
Master code # Enter the programming mode,default factory master code is 999999.
0.إعدادات النظام
0.Change Master code
Enter 6 to 8 digits new code # Repeat New code #
1.Register Add Admin 2.Register Delete Admin
Read card /input a fingerprint Read card /input a fingerprint
3.Working Mode 4.Data Backup 5.WiFi matching
0 #Reader mode) 1# (Standalone access control mode) 2# (Relay toggle mode)
0 #Data backup output) 1# (Data backup input)
# ……
(The Green wire and white wire of machine connects correspondingly)
7.Reset to Factory Default #
8.Storage Space
1.Add Users
1.Add card user
Input ID number read card or Input Card NO. #
2.Add PIN code user
Input ID number setting 4-6 digital door open code #
3.Add Fingerprint user
Input ID number press a fingerprint twice
4.Add Fingerprint +Card user Read user card press fingerprint twice (Note: unregistered new fingerprint)
5.Add conductive number Card Input ID number read card or input card number # input user quantity # 05
2.Delete Users
0.Delete all user
# (Notice: admin code won’t be deleted. )
1.Delete user ID number
Input ID number
#
(Notice : Delete pointed card , fingerprint or PIN code users by user ID number. )
2.Delete Card user
Read card or Input Card number #
3.Delete fingerprint user Press Fingerprint
4.Delete temporary code # (Notice : Delete the temporary code issued by the mobile phone App.)
3.Door Open Mode
1.Door Open Way
1. Forbidden (can’t open door) #
2.Entry by code only # 3.Entry by card only # 4.Entry by card(fingerprint )+code only #
5. Entry by card,code or fingerprint #
6.Entry by fingerprint only #
7. Entry by card+fingerprint #
8.Entry by multiple users #
2.Entry by multiple users Unlock by 1-10 users #
06
4. تحديد الوقت
1.Unlock time
المدخلات 0-300
# (Time range 0~300S, Factory default: 5S)
2.Alarm output time Input 0-99 # (Time range 0~99S, Factory default: 0S)
3.Date & time setting Input date # Input time #
5.Card Reader Model setting
1.Device ID
0-255 Device ID #
2.Wiegand output
WG26-58 #
3.Keyboard format 0 #4 bit wg output) 1# (8 bit inverse code) 2# (virtual card number)
6. الإعدادات الأساسية
1.Alarm model
0# (Forbidden) 1# (Alarm) 2# (Locked)
2.Keypad LED light 0~99 # Can set 0-99sFactory default 10S)
3. الحجم
0# (close) 1# (low) 2# (High)
4.language
0# (Chinese) 1# (English)
07
8. إعادة التعيين إلى إعدادات المصنع الافتراضية
When forget the administrator password,reset it to the factory default setting,The default administrator password is “999999” Method 1: Power off, power on, screen lights on,press the # key,The display will shows default settings is successful. Method 2: Power off,press the exit button continously,power on, The display will shows default settings is successful.
Method 3: 0.system setting 7.Reset factory default setting #
9. Reader mode switch to standalone access control mode When the device is under card reader mode, long press * to switch to standalone access control mode
10. Cancel alarm
Read admin card or read valid user card or valid fingerprint or admin password # Note: When alarm occurs, the buzzer will sound “woo, woo,…” and the alarm can be canceled by reading the valid card or inputting admin password.
قائمة 11.Packing
Item Device User Manual Self-tapping screwdriver Rubber plug Star screwdriver Star screws
مواصفة
4mm×25 mm 6mm×28 mm 20mm×60mm 3mm×5mm
الكمية
ملاحظة
1
1
2
للتركيب والتثبيت
2
للتركيب والتثبيت
1
غرض خاص
1
For fixing the front cover and
الغطاء الخلفي
Note: *Please do not repair the machine without permission. If there is any problem, please return it to the manufacturer for repair. *Before installation, if you want to drill holes, please carefully check the hidden wires or conduits to prevent unnecessary trouble caused by drilling the hidden wires when drilling. Use safety glasses when drilling or fixing wire clips. *If the product is upgraded, the instructions may be different without prior notice.
08
12. WIFI وظيفة
خياري
1 Scan the QR code by your mobile phone to download the Tuya Smart APP or search the Tuya Smart APP to download APP by mobile phone application market (Figure 1)
2 Open the APP, click the “+”at the upper right corner, Add Device (Figure 2) (Note: When searching for devices, turn on the
Bluetooth and location services functions firstly)
ملحوظة:
At the same time, turn on the “wireless function on the access control.Press
pairing” Admin
كلمة المرور
# 0. System settings
# 5. WIFI pairing #
3 Enter the WIFI password, then click Next. (Figure 3)
مسح رمز الاستجابة السريعة
TuyaSmart Search”TuyaSmart
تحميل
TuyaSmart Search”TuyaSmart”
تحميل
Search TuyaSmart to download APP Figure 1
الشكل 2
الشكل 3
09
4 Wait for successful connection,click Done
AC
AC
5 Set remote unlock,click setting,open remote unlock setting
AC
10
6 Press to unlock
AC
7 Member management Administrator Add fingerprint start adding input fingerprint twice add successfully,input name,click Done.
********
********
11
8
Add code user by clicking add temporary code periodically, and input 6 digits code or click randomly generated, then
input code name, and click save.
9
Add card by clicking start add, swiping one card within 60 seconds, add card successfully, then
fill card name and click “done”.
12
Add ordinary user by clicking ordinary member, 10 then click at the upper right corner “+”, then input
the related information and click “next step”.
13
11 Add temporary code, click `once”, input code name, click “save offline code”, done.
AC
14
12 Query unlock records
AC
13 Settings: access ways, alarm time, volume, language.
AC
Click hereto check the unlock records 15
المستندات / الموارد
![]() |
eSSL JS-36E Security Standalone Access Control [بي دي اف] دليل المستخدم JS-36E Security Standalone Access Control, JS-36E, Security Standalone Access Control, Standalone Access Control, Access Control |