JS-36E Security Standalone Access Control
“
Ƙayyadaddun bayanai
Mai aiki Voltage: Saukewa: DC12-24V
Aiki Yanzu: 100mA
Humidity Mai Aiki: 0% -95%
Jiran Yanzu: 60mA
Yanayin Aiki: -40-60 ° C
Access Ways: Fingerprint, card, code, multiple
combination methods, mobile phone App (Optional)
Umarnin Amfani da samfur
Shigarwa
- Remove the back cover form the keypad using the supplied
special screw drive. - Drill 2 holes on the wall for the self-tapping screw and 1 hole
don kebul. - Put the supplied rubber bungs into the two holes.
- Fix the back cover firmly on the wall with 2 self-tapping
sukurori. - Zare kebul ta ramin kebul.
- Attach the keypad to the back cover. (Refer to figure for
guidance)
Waya
| Alamar Launi | Bayani |
|---|---|
| Pink Bell-A | Door bell button on one end |
Saitin Tsari
- Master code #: Enter the programming mode,
default factory master code is 999999. - Saitin Tsari:
- Change Master code: Enter 6 to 8 digits new code, repeat new
code.
Wurin Ajiya
- Ƙara Masu Amfani:
- Add card user: Input ID number, read card or input Card
A'A.
Tambayoyin da ake yawan yi (FAQ)
Tambaya: Yadda ake sake saita na'urar zuwa saitunan masana'anta?
A: To reset to factory default, enter the programming mode and
use the specified code for resetting.
Tambaya: Menene kewayon zafin aiki na na'urar?
A: Na'urar na iya aiki a cikin kewayon zafin jiki na -40°C zuwa
60°C.
"'
JS-36E User Manual
Da fatan za a karanta littafin a hankali kafin amfani da wannan naúrar.
1. Gabatarwa
This series’s product is a new generation on multifunctional standalone access control.It adopts new ARM core 32-bit microprocessor design, which is powerful, stable and reliable . It contains reader mode and standalone access control mode etc.. It’s widely applied to different occasions, such as office, residential communities, villa, bank and prison etc..
2. Features
Nau'in Kati
Keypad Characteristic Output Way
Access Way Admin Card User Capacity Unlock Signal Alarm Output
Read 125KHz Card and HID Card(Optional) Read 13.56MHz Mifare card and CPU card(Optional) Capacitive touch keypad Contain reader mode, the transmission format could be adjusted by user Fingerprint , card,code or multiple combination methods, mobile phone App (Optional Support admin add card and admin delete card 10000 NO, NC, COM output using relay Use MOS tube output to directly drive the alarm (optional)
3.Tattausan Bayani
Mai aiki Voltage: DC12-24V Operating Current100mA
Humidity Aiki: 0% -95%
Jiran aiki na yanzu 60mA
Operating Temperature:-40-60
Access waysFingerprint, card, code, multiple combination methods, mobile phone App (Optional
01
4. Shigarwa
Cire faifan maɓalli na baya ta amfani da faifan maɓalli na musamman da aka kawo
Drill 2 holes on the wall for the self-tapping screw and 1 hole for the cable Put the supplied rubber bungs to into the two holes Fix the back cover firmly on the wall with 2 self tapping screws Thread the cable through the cable hole Attached the keypad to the back cover.(See the figure right)
5. Waya
Alamar Launi
Bayani
Pink Bell-A
Maɓallin kararrawa a ƙarshen
Pink Bell-B
Maɓallin kararrawa a ɗayan ƙarshen
Green D0 White D1
Wiegand input (Wiegand output as reader mode) Wiegabd inputWiegand output as reader mode
Grey Alarm
Siginar ƙararrawa MOS tube magudanar fitarwa ƙarshen fitarwa
Yellow Open(BEEP) Exit button input end(Beeper input as reader mode)
Brown DIN(LED)
Ƙarshen shigarwar firikwensin firikwensin ƙofa (yanayin mai karanta kati, shigarwar sarrafa LED)
Ja
+12V
Tabbataccen wutar lantarki
Farashin GND
Ƙarfin wutar lantarki mara kyau
Blue NO
Relay BABU ƙarewa
Purple COM
Relay COM karshen
Orange NC
Relay NC karshen
02
6. zane
1. Special power supply diagram
Electric Rim Lock
Electritc mortise lock Magnetic lock
GND PUSH GND +12V NO NC
AC 220 V
Maballin Fita
Red Black Purple Blue Yelow
03
6.2 Yanayin Karatu
Ja Bakar Koren Fari
04
7.System Saitin
Master code # Enter the programming mode,default factory master code is 999999.
0.System Saitin
0.Change Master code
Enter 6 to 8 digits new code # Repeat New code #
1.Register Add Admin 2.Register Delete Admin
Read card /input a fingerprint Read card /input a fingerprint
3.Working Mode 4.Data Backup 5.WiFi matching
0 #Reader mode) 1# (Standalone access control mode) 2# (Relay toggle mode)
0 #Data backup output) 1# (Data backup input)
# ……
(The Green wire and white wire of machine connects correspondingly)
7.Reset to Factory Default #
8.Storage Space
1.Add Users
1.Add card user
Input ID number read card or Input Card NO. #
2.Add PIN code user
Input ID number setting 4-6 digital door open code #
3.Add Fingerprint user
Input ID number press a fingerprint twice
4.Add Fingerprint +Card user Read user card press fingerprint twice (Note: unregistered new fingerprint)
5.Add conductive number Card Input ID number read card or input card number # input user quantity # 05
2.Delete Users
0.Delete all user
# (Notice: admin code won’t be deleted. )
1.Delete user ID number
Input ID number
#
(Notice : Delete pointed card , fingerprint or PIN code users by user ID number. )
2.Delete Card user
Read card or Input Card number #
3.Delete fingerprint user Press Fingerprint
4.Delete temporary code # (Notice : Delete the temporary code issued by the mobile phone App.)
3.Door Open Mode
1.Door Open Way
1. Forbidden (can’t open door) #
2.Entry by code only # 3.Entry by card only # 4.Entry by card(fingerprint )+code only #
5. Entry by card,code or fingerprint #
6.Entry by fingerprint only #
7. Entry by card+fingerprint #
8.Entry by multiple users #
2.Entry by multiple users Unlock by 1-10 users #
06
4.Time saitin lokaci
1.Unlock time
Shigar da 0-300
# (Time range 0~300S, Factory default: 5S)
2.Alarm output time Input 0-99 # (Time range 0~99S, Factory default: 0S)
3.Date & time setting Input date # Input time #
5.Card Reader Model setting
1.Device ID
0-255 Device ID #
2.Wiegand output
WG26-58 #
3.Keyboard format 0 #4 bit wg output) 1# (8 bit inverse code) 2# (virtual card number)
6.Basic Settings
1.Alarm model
0# (Forbidden) 1# (Alarm) 2# (Locked)
2.Keypad LED light 0~99 # Can set 0-99sFactory default 10S)
3.Juzu'i
0# (close) 1# (low) 2# (High)
4.language
0# (Chinese) 1# (English)
07
8.Sake saita zuwa Tsoffin Factory
When forget the administrator password,reset it to the factory default setting,The default administrator password is “999999” Method 1: Power off, power on, screen lights on,press the # key,The display will shows default settings is successful. Method 2: Power off,press the exit button continously,power on, The display will shows default settings is successful.
Method 3: 0.system setting 7.Reset factory default setting #
9. Reader mode switch to standalone access control mode When the device is under card reader mode, long press * to switch to standalone access control mode
10. Cancel alarm
Read admin card or read valid user card or valid fingerprint or admin password # Note: When alarm occurs, the buzzer will sound “woo, woo,…” and the alarm can be canceled by reading the valid card or inputting admin password.
11.Packing list
Item Device User Manual Self-tapping screwdriver Rubber plug Star screwdriver Star screws
Ƙayyadaddun bayanai
4mm×25 mm 6mm×28 mm 20mm×60mm 3mm×5mm
Qty
Magana
1
1
2
Don hawa da gyara
2
Don hawa da gyarawa
1
manufa ta musamman
1
For fixing the front cover and
murfin baya
Note: *Please do not repair the machine without permission. If there is any problem, please return it to the manufacturer for repair. *Before installation, if you want to drill holes, please carefully check the hidden wires or conduits to prevent unnecessary trouble caused by drilling the hidden wires when drilling. Use safety glasses when drilling or fixing wire clips. *If the product is upgraded, the instructions may be different without prior notice.
08
12. Aikin WIFI
na zaɓi
1 Scan the QR code by your mobile phone to download the Tuya Smart APP or search the Tuya Smart APP to download APP by mobile phone application market (Figure 1)
2 Open the APP, click the “+”at the upper right corner, Add Device (Figure 2) (Note: When searching for devices, turn on the
Bluetooth and location services functions firstly)
Lura:
At the same time, turn on the “wireless function on the access control.Press
pairing” Admin
kalmar sirri
# 0. System settings
# 5. WIFI pairing #
3 Enter the WIFI password, then click Next. (Figure 3)
Duba lambar QR
TuyaSmart Search”TuyaSmart
zazzagewa
TuyaSmart Search”TuyaSmart”
zazzagewa
Search TuyaSmart to download APP Figure 1
Hoto 2
Hoto3
09
4 Wait for successful connection,click Done
AC
AC
5 Set remote unlock,click setting,open remote unlock setting
AC
10
6 Press to unlock
AC
7 Member management Administrator Add fingerprint start adding input fingerprint twice add successfully,input name,click Done.
*******
*******
11
8
Add code user by clicking add temporary code periodically, and input 6 digits code or click randomly generated, then
input code name, and click save.
9
Add card by clicking start add, swiping one card within 60 seconds, add card successfully, then
fill card name and click “done”.
12
Add ordinary user by clicking ordinary member, 10 then click at the upper right corner “+”, then input
the related information and click “next step”.
13
11 Add temporary code, click `once”, input code name, click “save offline code”, done.
AC
14
12 Query unlock records
AC
13 Settings: access ways, alarm time, volume, language.
AC
Click hereto check the unlock records 15
Takardu / Albarkatu
 |
eSSL JS-36E Security Standalone Access Control [pdf] Manual mai amfani JS-36E Security Standalone Access Control, JS-36E, Security Standalone Access Control, Standalone Access Control, Access Control |