Atmel ATF15xx-DK3 CPLD Ntshetsopele / Setsi sa Lenaneo
Selelekela
Atmel® ATF15xx-DK3 Complex Programmable Logic Device (CPLD) Development/Programmer Kit ke sistimi e felletseng ea nts'etsopele le lenaneo la In-System Programming (ISP) bakeng sa Atmel ATF15xx Lelapa la li-CPLD tsa maemo a holimo tsa indasteri tse lumellanang le likarolo tsa Logic Doubling®. Setsi sena se fa baqapi tsela e potlakileng le e bonolo ea ho etsa lipapiso le ho lekola meralo e mecha ka ATF15xx ISP CPLD. Lelapa la ATF15xx la ISP CPLD le kenyelletsa Atmel ATF15xxAS, ATF15xxASL, ATF15xxASV, le ATF15xxASVL CPLDs. Ka boteng ba liboto tse fapaneng tsa li-adapter tsa sokete ho ts'ehetsa boholo ba mefuta ea liphutheloana(1) e fanoang ho ATF15xx Family of ISP CPLDs, kit ena e ka sebelisoa e le lenaneo la ISP ho hlophisa li-ATF15xx ISP CPLD ho bongata ba mefuta e fumanehang ea liphutheloana. (1) ka maemo a indasteri JTAG segokanyimmediamentsi sa sebolokigolo (IEEE 1149.1).
Litaba tsa Kit
- Boto ea Ntlafatso ea Atmel CPLD/Morero (P/N: ATF15xx-DK3)
- Atmel 44-pin TQFP Socket Adapter Board (P/N: ATF15xx-DK3-SAA44)(2)
- Atmel ATF15xx LPT e thehiloeng JTAG ISP Download Cable (P/N: ATDH1150VPC)
- Tse peli tsa Atmel 44-pin TQFP Sample Lisebelisoa
Tšehetso ea lisebelisoa
ATF15xx-DK3 CPLD Development/Programmer Kit e ts'ehetsa lisebelisoa tse latelang ho limaraka le liphutheloana tsohle tse fumanehang hona joale tsa Atmel (ntle le 100-PQFP):
- ATF1502AS/ASL
- ATF1504AS/ASL
- ATF1508ASV/ASVL
- ATF1502ASV
- ATF1504ASV/ASVL
- ATF1508AS/ASL
- Boto ea adaptara ea socket ha e fanoe bakeng sa PQFP ea 100-pin.
- Ke Boto ea Adapter ea TQFP ea 44-pin feela e kenyellelitsoeng ka har'a kit ena. Liboto tse ling tsa socket adapter li rekisoa ka thoko. Sheba Karolo, "Hardware Description" bakeng sa tlhahisoleseding e eketsehileng mabapi le socket adapter board codes.i
Likarolo tsa Kit
Boto ea Ntlafatso ea CPLD / Lenaneo
- 10-pin JTAG-ISP Port
- Lipotoloho tsa Phepelo ea Matla tse laoloang bakeng sa Mohloli oa Matla oa 9VDC
- 5V, 3.3V, 2.5V, kapa 1.8VI/O Voltage Phepelo
- Khetho ea 1.8V, 3.3V, kapa 5.0V Core Voltage Phepelo
- 44-pin TQFP Socket Adapter Board
- Lihlooho tsa I/O Pins tsa Sesebelisoa sa ATF15xx
- 2MHz Crystal Oscillator
- Lipontšo tsa LED tsa likarolo tse 7 tse 'ne
- Li-LED tse robeli tsa Motho ka Mong
- Liphetoho tse robeli tsa Push-button
- Global Hlakileng le Output Numella Push-konopo Switjha
- Li-Jumpers tsa Tekanyo tsa Hona Joale
Logic Doubling CPLDs
ATF15xx ISP CPLD e nang le Logic Doubling Architecture
- ATF15xx ISP Download Cable
- 5V, 3.3V, 2.5V, kapa 1.8V ISP Download Cable for PC Parallel Printer (LPT) Port
- PLD Development Software
- Lisebelisoa tsa software tsa nts'etsopele ea Atmel PLD li fumaneha marang-rang bakeng sa tšebeliso ea moqapi oa PLD ea ATF15xx ISP CPLDs. Ka kopo sheba Overview tokomane, "PLD
- Moralo oa Software Overview” e fumaneha ho:
- http://www.atmel.com/images/atmel-3629-pld-design-software-overview.pdf
Litlhoko tsa Tsamaiso
- Bonyane bo tlase ba hardware le software e hlokehang ho hlophisa sesebelisoa sa ATF15xx ISP CPLD se entsoeng ho sebelisoa Atmel ProChip Designer Software ho CPLD Development/Programme Board ka Atmel ATMISP v6.x (ATF15xx CPLD ISP Software) ke:
- x86 Microprocessor-based Computer
- Windows XP®, Windows® 98, Windows NT® 4.0, kapa Windows 2000
- 128-MByte RAM
- 500-MByte Free Hard Disk Space
- Toeba e tšehelitsoeng ke Windows
- E Fumaneha Parallel Printer (LPT) Port
- Phepelo ea Matla a 9VDC e nang le 500mA ea Phepelo ea Hona Joale
- SVGA Monitor (800 x 600 Resolution)
Ho Odara Boitsebiso
| Nomoro ea Karolo ea Atmel | Tlhaloso |
| ATF15xx-DK3 | CPLD Development/Programmer Kit (e kenyelletsa ATF15xxDK3-SAA44*) |
| ATF15xxDK3-SAA100 | 100-pin TQFP Socket Adapter Board bakeng sa Boto ea DK3 |
| ATF15xxDK3-SAJ44 | 44-pin PLCC Socket Adapter Board bakeng sa Boto ea DK3 |
| ATF15xxDK3-SAJ84 | 84-pin PLCC Socket Adapter Board bakeng sa Boto ea DK3 |
| ATF15xxDK3-SAA44* | 44-pin TQFP Socket Adapter Board bakeng sa Boto ea DK3 |
Tlhaloso ea Hardware
Boto ea Ntlafatso ea CPLD / Lenaneo
- CPLD Development/Programmer le Socket Adapter Boards e bontšitsoeng setšoantšong se ka tlase e na le likarolo tse thusang ho nts'etsapele, ho etsa prototyping kapa ho lekola.
- Meetso ea ATF15xx CPLD. Likarolo tse etsang hore sena e be sesebelisoa sa ho qala / nts'etsopele le sesebelisoa sa ISP bakeng sa lelapa la ATF15xx la J.TAG-ISP CPLDs e kenyelletsa:
- Liphetoho tsa konopo ea Push
- Li-LED
- Lipontšo tsa likarolo tse 7
- 2MHz Crystal Oscillator
- 5V, 3.3V, 2.5V, kapa 1.8V VCCIO Selector
- 1.8V, 3.3V, kapa 5.0V VCCINT Selector
- JTAG Boema-kepe ba ISP
- Li-adapter tsa Socket
- Lipontšo tsa likarolo tse 7 tse nang le li-Jumpers tse Khethollang
- CPLD Development/Programme Board e na le lipontšo tse 'ne tsa likarolo tse 7 tse lumellang ho hlokomeloa ha liphetho tsa ATF15xx CPLD. Lipontšo tsena tse 'ne li ngotsoe e le DSP1, DSP2, DSP3, le DSP4. Lipontšo tsa likarolo tse 7 li na le li-LED tse tloaelehileng tsa anode tse nang le mela e tloaelehileng ea anode e amanang le VCCIO (I/O supply vol.tage bakeng sa CPLD) ka letoto la lihanyetsi tse nang le li-jumpers tse khethiloeng tse ngotsoeng e le JPDSP1, JPDSP2, JPDSP3, le JPDSP4. Li-jumpers tsena li ka tlosoa ho
thibela lipontšo ka ho tlosa VCCIO ho lipontšo. Mehala ea cathode ka bomong e hokahane le lithakhisa tsa I/O tsa ATF15xx CPLD ho CPLD. - Setsi sa Nts'etsopele / Lenaneo. Ho bulela karolo e itseng, ho kenyeletsoa le DOT ea ponts'o, pinana e tsamaellanang ea ATF15xx I/O e hokahantsoeng le karolo ena ea LED e tlameha ho ba maemong a tlase a utloahalang le sete sa jumper se lumellanang le sona; ka hona, liphetho tsa sesebelisoa sa ATF15xx li tla hloka tlhophiso bakeng sa liphetho tse tlase-tlase moralong. file. Lipontšo li sebetsa hantle ho 2.5V VCCIO kapa ho feta.
- Karolo e 'ngoe le e' ngoe ea pontšo e 'ngoe le e' ngoe e na le mohala o thata ho pini e le 'ngoe ea I/O ea sesebelisoa sa ATF15xx. Bakeng sa lisebelisoa tse phahameng tsa ho bala li-pin (100-pin le tse khōloanyane), likarolo tsohle tse supileng le likarolo tsa DOT tsa lipontšo tse 'nè li hokahane le li-pin tsa I/O; leha ho le joalo, bakeng sa lisebelisoa tse tlase tsa ho bala lipini, ke karoloana feela ea lipontšo, lipontšo tsa pele le tsa bone, tse hokahaneng le lithakhisa tsa I/O tsa sesebelisoa sa ATF15xx. Litafole 1 le 2 li bonts'a likhokahano tsa sephutheloana sa likarolo tse 7 ho sesebelisoa sa ATF15xx. Sekema sa potoloho ea lipontšo le li-jumpers se bontšoa setšoantšong se ka tlase.
Setšoantšo sa 2. Setšoantšo sa Potoloho sa Pontšo ea likarolo tse 7 le Li-Jumpers
Tafole 1.ATF15xx 44-pin Connections to 7-segment Displays
| 44-pin TQFP | |||
| DSP/Karolo | Setšoantšo sa PLD | DSP/Karolo | Setšoantšo sa PLD |
| 1/A | 27 | 3/A | NC |
| 1/B | 33 | 3/B | NC |
| 1/C | 30 | 3/C | NC |
| 1/D | 21 | 3/D | NC |
| 1/E | 18 | 3/E | NC |
| 1/F | 23 | 3/F | NC |
| EA-1 / G | 20 | EA-3 / G | NC |
| 1/DOT | 31 | 3/DOT | NC |
| 2/A | NC | 4/A | 3 |
| 2/B | NC | 4/B | 10 |
| 2/C | NC | 4/C | 6 |
| 2/D | NC | 4/D | 43 |
| 2/E | NC | 4/E | 35 |
| 2/F | NC | 4/F | 42 |
| EA-2 / G | NC | EA-4 / G | 34 |
| 2/DOT | NC | 4/DOT | 11 |
| PLCC ea lintlha tse 44 | |||
| DSP/Karolo | Setšoantšo sa PLD | DSP/Karolo | Setšoantšo sa PLD |
| 1/A | 33 | 3/A | NC |
| 1/B | 39 | 3/B | NC |
| 1/C | 36 | 3/C | NC |
| 1/D | 27 | 3/D | NC |
| 1/E | 24 | 3/E | NC |
| 1/F | 29 | 3/F | NC |
| EA-1 / G | 26 | EA-3 / G | NC |
| 1/DOT | 37 | 3/DOT | NC |
| 2/A | NC | 4/A | 9 |
| 2/B | NC | 4/B | 16 |
| 2/C | NC | 4/C | 12 |
| 2/D | NC | 4/D | 5 |
| 2/E | NC | 4/E | 41 |
| 2/F | NC | 4/F | 4 |
| EA-2 / G | NC | EA-4 / G | 40 |
| 2/DOT | NC | 4/DOT | 17 |
Tafole 2.ATF15xx 84-pin le likhokahano tse 100 ho Lipontšo tsa likarolo tse 7
| PLCC ea lintlha tse 84 | |||
| DSP/Karolo | Setšoantšo sa PLD | DSP/Karolo | Setšoantšo sa PLD |
| 1/A | 68 | 3/A | 22 |
| 1/B | 74 | 3/B | 28 |
| 1/C | 70 | 3/C | 25 |
| 1/D | 63 | 3/D | 21 |
| 1/E | 58 | 3/E | 16 |
| 1/F | 65 | 3/F | 17 |
| EA-1 / G | 61 | EA-3 / G | 12 |
| 1/DOT | 73 | 3/DOT | 29 |
| 2/A | 52 | 4/A | 5 |
| 2/B | 57 | 4/B | 10 |
| 2/C | 55 | 4/C | 8 |
| 2/D | 48 | 4/D | 79 |
| 2/E | 41 | 4/E | 76 |
| 2/F | 50 | 4/F | 77 |
| EA-2 / G | 45 | EA-4 / G | 75 |
| 2/DOT | 50 | 4/DOT | 11 |
| 100-pin TQFP | |||
| DSP/Karolo | Setšoantšo sa PLD | DSP/Karolo | Setšoantšo sa PLD |
| 1/A | 67 | 3/A | 13 |
| 1/B | 71 | 3/B | 19 |
| 1/C | 69 | 3/C | 16 |
| 1/D | 61 | 3/D | 8 |
| 1/E | 57 | 3/E | 83 |
| 1/F | 64 | 3/F | 6 |
| EA-1 / G | 60 | EA-3 / G | 92 |
| 1/DOT | 75 | 3/DOT | 20 |
| 2/A | 52 | 4/A | 100 |
| 2/B | 54 | 4/B | 94 |
| 2/C | 47 | 4/C | 97 |
| 2/D | 41 | 4/D | 81 |
| 2/E | 46 | 4/E | 76 |
| 2/F | 40 | 4/F | 80 |
| EA-2 / G | 45 | EA-4 / G | 79 |
| 2/DOT | 56 | 4/DOT | 93 |
Li-LED tse nang le li-Jumpers tse Khethollang
Boto ea CPLD Development/Programmer e na le li-LED tse robeli, tse lumellang baqapi ho bonts'a matšoao a tsoang ho basebelisi ba I/O ba lisebelisoa tsa ATF15xx. Li-LED tsena tse robeli li ngotsoe LED1 ho LED8 ho CPLD Development/Programmer Board. Cathode ea LED e 'ngoe le e' ngoe e hokahane le Ground (GND) ka letoto la mohanyetsi, ha anode ea LED e 'ngoe le e 'ngoe e hokahane le pinana ea I/O ea CPLD ka JPL1/2/3/4/5/6/7 /8 jumper e kgethehang. Li-jumpers tsena li ka tlosoa ho thibela li-LED ka ho tlosa li-anode tsa li-LED ho li-pin tsa I / O tsa CPLD. Setšoantšo se ka tlase se bontša setšoantšo sa potoloho ea li-LED tse nang le li-jumpers tsa khetho.
Ho bulela LED e itseng, pinana e tsamaellanang ea ATF15xx I/O e hokahantsoeng le LED e tlameha ho ba boemong bo phahameng ba logic le sete e lumellanang ea jumper; ka hona, liphetho tsa sesebelisoa sa ATF15xx li tla hloka ho hlophisoa e le liphetho tse phahameng tse sebetsang. Li-LED li sebetsa hantle ho 2.5V VCCIO kapa ho feta.
Lisebelisoa tse tlase tsa ho bala lipini (44-pin) li na le li-I/O tse 'ne feela tse hokahaneng le LED1/2/3/4. Bakeng sa lisebelisoa tse phahameng tsa pin-count (100-pin le tse kholoanyane), li-LED tse robeli kaofela li hokahane le li-I/O tsa sesebelisoa. Letlapa la 3 le bonts'a likhokahano tse fapaneng tsa liphutheloana tsa CPLD I/Os ho li-LED.
Letlapa la 3.ATF15xx Lihokelo ho li-LED
| 44-pin TQFP | |
| LED | Setšoantšo sa PLD |
| LED1 | 28 |
| LED2 | 25 |
| LED3 | 22 |
| LED4 | 19 |
| PLCC ea lintlha tse 44 | |
| LED | Setšoantšo sa PLD |
| LED1 | 34 |
| LED2 | 31 |
| LED3 | 28 |
| LED4 | 25 |
| PLCC ea lintlha tse 84 | |
| LED | Setšoantšo sa PLD |
| LED1 | 69 |
| LED2 | 67 |
| LED3 | 64 |
| LED4 | 60 |
| LED5 | 27 |
| LED6 | 24 |
| LED7 | 18 |
| LED8 | 15 |
| 100-pin TQFP | |
| LED | Setšoantšo sa PLD |
| LED1 | 68 |
| LED2 | 65 |
| LED3 | 63 |
| LED4 | 58 |
| LED5 | 17 |
| LED6 | 14 |
| LED7 | 10 |
| LED8 | 9 |
Li-switches tsa Push-button tse nang le Li-Jumpers tse Kgethehang bakeng sa Lithakhisa tsa I/O
- Boto ea CPLD Development / Programmer e na le li-switches tse robeli tsa push-button, tse hokahaneng le lithapo tsa I/O tsa CPLD. Li-switch li romella matšoao a ho kenya letsoho ho li-pin tsa I/O tsa sesebelisoa sa ATF15xx. Liphetoho tsena li ngotsoe SW1 ho SW8 ho CPLD Development/Programmer
Boto. Qetello e le 'ngoe ea konopo e' ngoe le e 'ngoe ea ho sutumetsa e hokahane le VCCIO, ha pheletsong e' ngoe ea konopo e 'ngoe le e' ngoe e hokahane le mochini o hulang fatše ebe o hokahana le phini e khethehileng ea I/O ea CPLD ka JPS1/2. /3/4/5/6/7/8 jumper e kgethollang. - Haeba e 'ngoe ea li-switches tsena e hatelloa' me jumper e lumellanang e behiloe, pinana e khethehileng ea I / O ea sesebelisoa e tla khannoa sebakeng se phahameng sa logic ka tlhahiso ea potoloho ea switch. Kaha konopo e 'ngoe le e' ngoe ea push-button e boetse e hokahane le mohanyetsi oa ho hula fatše, ho kenya letsoho ho tla ba le boemo bo tlaase ba logic haeba sesebelisoa se sa hatelloa ka sete sa jumper se lumellanang. Haeba jumper ea push-button e sa behoa, pinana e lumellanang e tla tšoaroa e le phini e sa kopanngoa. Setšoantšo sa 4 ke setšoantšo sa potoloho sa konopo ea push-button le jumper e khethiloeng. Letlapa la 4 le bonts'a likhokahano tsa li-switches tsena tse robeli tsa li-push-button ho lithapo tsa CPLD I/O ka mefuta e fapaneng ea liphutheloana.
Letlapa la 4.ATF15xx Lihokelo ho Liphetoho tsa Pin tsa I / O
| 44-pin TQFP | |
| Tobetsa Konopo | Setšoantšo sa PLD |
| SW1 | 15 |
| SW2 | 14 |
| SW3 | 13 |
| SW4 | 12 |
| SW5 | 8 |
| SW6 | 5 |
| SW7 | 2 |
| SW8 | 44 |
| PLCC ea lintlha tse 44 | |
| Tobetsa Konopo | Setšoantšo sa PLD |
| SW1 | 21 |
| SW2 | 20 |
| SW3 | 19 |
| SW4 | 18 |
| SW5 | 14 |
| SW6 | 11 |
| SW7 | 8 |
| SW8 | 6 |
| PLCC ea lintlha tse 84 | |
| Tobetsa Konopo | Setšoantšo sa PLD |
| SW1 | 54 |
| SW2 | 51 |
| SW3 | 49 |
| SW4 | 44 |
| SW5 | 9 |
| SW6 | 6 |
| SW7 | 4 |
| SW8 | 80 |
| 100-pin TQFP | |
| Tobetsa Konopo | Setšoantšo sa PLD |
| SW1 | 48 |
| SW2 | 36 |
| SW3 | 44 |
| SW4 | 37 |
| SW5 | 96 |
| SW6 | 98 |
| SW7 | 84 |
| SW8 | 99 |
Li-Switch-button tse nang le Li-Jumpers tse Khethollang bakeng sa GCLR le OE1 Pins
Boto ea CPLD Development/Programmer e na le li-switches tse peli tsa li-push-button bakeng sa Global Clear (GCLR) le Output Enable (OE1) ea CPLD. Li-switch li laola maemo a matle a OE1 le GCLR ea lisebelisoa tsa ATF15xx. Li-switch tsena li ngotsoe SW-GCLR le SW-GOE1 botong. Qetello e 'ngoe ea switjha ea konopo ea SW-GCLR e hoketsoe ho GND. Qetello e 'ngoe ea
switch-button switch e hokahane le mochini o hulang holimo ho VCCIO ebe o hokahana le phini ea ho kenya e inehetseng ea GCLR ea sesebelisoa sa ATF15xx. E reretsoe ho sebelisoa e le lets'oao le sebetsang-tlase la ho seta bocha ho hlophisa bocha lirekoto ho sesebelisoa sa ATF15xx ka sete ea jumper e khethiloeng ea JPGCLR. Ka mokhoa o ts'oanang, pheletso e 'ngoe ea konopo ea SW-GOE1 e hokahane le GND. Qetello e 'ngoe ea konopo ea push-button
e hokahantsoe le mochini o hulang holimo ho VCCIO ebe e hokahana le phini ea ho kenya e inehetseng ea OE1 ea sesebelisoa sa ATF15xx. E reretsoe ho sebelisoa e le sehlahisoa se sebetsang-tlase se nolofalletsang lets'oao ho laola ho nolofalletsa / ho thibela li-buffers tsa tri-state ho ATF15xx ka sete ea jumper e khethiloeng ea JPGOE. Setšoantšo sa 5 ke setšoantšo sa potoloho ea li-switches tsa push-button le li-jumpers tsa GCLR le OE1 pins.
Haeba leha e le efe ea li-switches tsena tsa push-button e hatelloa 'me jumper e lumellanang e behiloe, I / O e khethehileng ea CPLD e tla khannoa ho ea boemong bo tlaase bo utloahalang. Kaha konopo e 'ngoe le e' ngoe ea push-up e boetse e hokahane le mohanyetsi oa ho hula, ho kenya letsoho ho CPLD ho tla ba le boemo bo phahameng ba logic haeba konopo ea push-button e sa hatisoe ka jumper e lumellanang e khethiloeng. Haeba jumper e khethiloeng e sa behoa, pini e lumellanang e inehetseng ea CPLD e ka nkoa e le phini ea No Connect (NC). Letlapa la 5 le bonts'a linomoro tsa phini tsa GCLR le OE1 tse inehetseng tse kenyang lisebelisoa tsa ATF15xx mefuteng eohle e fumanehang ea liphutheloana.
Setšoantšo sa 5. Setšoantšo sa Potoloho sa Liphetoho tsa Push-button le Li-Jumpers tse Khethollang bakeng sa GCLR le OE1
Lethathamo la 5.Pin Nomoro ea GCLR le OE1
| 44-pin TQFP | PLCC ea lintlha tse 44 | PLCC ea lintlha tse 84 | 100-pin TQFP | |
| GCLR | 39 | 1 | 1 | 89 |
| OE1 | 38 | 44 | 84 | 88 |
2MHz Oscillator le Clock Selection Jumper
Clock Selection Jumper e ngotsoeng JP-GCLK ho CPLD Development/Programmer Board ke jumper e nang le maemo a mabeli e lumellang basebelisi ho khetha hore na GCLK e inehetseng ea pin (ebang ke GCLK1 kapa GCLK2) ea sesebelisoa sa ATF15xx e lokela ho hokahanngoa le tlhahiso ea 2MHz oscillator. Ho phaella moo, jumper e ka tlosoa ho lumella mohloli oa oache o ka ntle hore o hokahane le GCLK1 le / kapa GCLK2 ea sesebelisoa sa ATF15xx. Setšoantšo sa 6 ke papiso ea setšoantšo sa potoloho ea oscillator le jumper ea khetho. Letlapa la 6 le bonts'a linomoro tsa phini bakeng sa GCLK1 le GCLK2 li-pin tse inehetseng tsa sesebelisoa sa ATF15xx mefuteng eohle e fapaneng e fumanehang ea liphutheloana.
Haeba jumper ea GCLK1 e behiloe, jumper e tla be e le ka lehlakoreng la boto. Ka lehlakoreng le leng, haeba jumper ea GCLK2 e behiloe, jumper e tla be e le bohareng ba boto.
Lethathamo la 6.Pin Nomoro ea GCLK1 le GCLK2
| 44-pin TQFP | PLCC ea lintlha tse 44 | PLCC ea lintlha tse 84 | 100-pin TQFP | |
| GCLK1 | 37 | 43 | 83 | 87 |
| GCLK2 | 40 | 2 | 2 | 90 |
VCCIO le VCCINT Moqtage Selection Jumpers le LEDs
- The VCCIO le VCCINT Moqtage Selection Jumpers, e ngotsoeng VCCIO Selector le VCCINT Selector ka ho latellana ho ATF15xx-DK3 Development/Programming Kit, lumella khetho ea phepelo ea I/O
- voltage level (VCCIO) le core supply voltage level (VCCINT) tse sebelisetsoang sepheo sa CPLD ho kit. Hang ha li-jumpers tsena li behiloe ka nepo, li-LED (tse ngotsoeng VCCINT LED le VCCIO LED) li tla bulela; leha ho le joalo, ka phepelo e tlase ea voltage (ke hore 2.5V kapa tlase), li-LED li ka ba lerootho haholo.
- Bakeng sa ATF15xxAS/ASL (5.0V) CPLDs, VCCIO Selector le VCCINT Selector jumpers li tlameha ho hlophisoa ho 5.0V.
- Bakeng sa ATF15xxASV/ASVL (3.3V) CPLDs, VCCIO Selector le VCCINT Selector Jumpers li tlameha ho hlophisoa ho 3.3V feela.
- Matla a CPLD Development/Programmer Kit a tlameha ho tima ha o fetola boemo ba VCCIO kapa VCCINT Vol.tage Selection Jumper (VCCIO Selector kapa VCCINT Selector).
- ICCIO le ICCINT Jumpers
- Li-jumpers tsa ICCIO le ICCINT li ka tlosoa 'me tsa sebelisoa e le lintlha tsa tekanyo ea ICC. Ha li-jumpers li tlosoa, limithara tsa hona joale li ka kopanngoa le li-post ho lekanya tšebeliso ea hona joale ea sepheo sa CPLD. Ha basebelisi ba sa sebelise li-jumpers tsena ho lekanya hona joale, li-jumpers tsena li tlameha ho behoa e le hore kit le CPLD li sebetse.
- Moqtage Balaoli
- Li-voltagbalaoli ba e, ba ngotsoeng VR1 le VR2, ba sebelisetsoa ho iketsetsa le ho laola
- VCCINT le VCCIO voltage tsoa ho phepelo ea motlakase ea 9VDC. Bakeng sa lintlha, ka kopo bona moralo oa ATF15xx-DK3 kit, Setšoantšo sa 12.
- Phetoho ea Phepelo ea Matla le LED ea Matla
- Power Supply Switch, e ngotsoeng POWER SWITCH, e ka fetisetsoa sebakeng sa ho tima kapa ho tima, se sebelisetsoang ho bulela kapa ho tima matla a boto ea ATF15xx-DK3 ka ho latellana. E lumella 9VDC voltage ho Power Supply Jack ho fetela ho voltage balaoli ha e le boemong ba. Ha Power Supply Switch e buletsoe, Power LED (e ngotsoeng POWER LED) e tla khantša ho bontša hore ATF15xx-DK3 Kit e fanoa ka matla.
- Jack Supply Jack le Sehlooho sa Phepelo ea Matla
- Boto ea ATF15xx-DK3 e na le mefuta e 'meli e fapaneng ea likhokahanyo tsa phepelo ea motlakase tse ngotsoeng JPower le JP Power. E 'ngoe ea likhokahano tsena tsa phepelo ea motlakase e ka sebelisoa ho hokela mohloli oa matla oa 9VDC ho kit. Sehokelo sa pele sa matla se ngotsoeng JPower, ke jeke ea matla a barrel e nang le poso ea bophara ba 2.1mm, 'me e kopana le plug ea basali ea 2.1mm (ka hare) x 5.5mm (bophahamo ba ka ntle). Sehlooho sa bobeli sa phepelo ea motlakase se ngotsoeng JP Power, ke hlooho ea 4-pin e tona ea 0.100 ″ e nang le lipalo tsa lisekoere tsa 0.025 ″. Ho fumaneha ha mefuta ena e 'meli ea likhokahanyo tsa motlakase ho lumella basebelisi ho khetha mofuta oa lisebelisoa tsa phepelo ea motlakase tseo ba ka li sebelisang bakeng sa ATF15xx-DK3 Development/Programmer Kit.
- Ke e le 'ngoe feela ea likhokahano tsena tse peli tsa phepelo ea motlakase e lokelang ho tsamaisoa ka mohloli oa 9VDC empa eseng ka bobeli ka nako e le ngoe.
- JTAG ISP Connector le TDO Selection Jumper
- Leano la JTAG ISP Connector e ngotsoeng JTAG-IN, e sebelisetsoa ho hokahanya ATF15xx JTAG port pins (TCK, TDI, TMS, le TDO) ka thapo ea khoaso ea ISP ho ea ho parallel printer (LPT) koung ea PC bakeng sa J.TAG Lenaneo la ISP la sesebelisoa sa ATF15xx. Lihokelo tsa polarized li sebelisoa ho ATF15xx-DK3 le ISP Download Cable ho fokotsa mathata a khokahano. Leibole ea PIN1 e tlase ho JTAG Sehokedi sa ISP se bontsha sebaka sa phini 1 sa hlooho ya diphini tse 10 mme se fokotsa monyetla wa ho hokela ISP Download Cable ka phoso.
- Ka ho le letšehali la JTAG-IN sehokelo, ho na le litšiea tse peli tsa vias, 'me li ngotsoe JTAG- TSOA. Li etselitsoe ho lumella basebelisi ho theha JTAG Daisy chain ho etsa JTAG ts'ebetso ho lisebelisoa tse ngata. Basebelisi ba tla hloka ho rekisa sehokelo sa mofuta o tšoanang le o sebelisitsoeng bakeng sa JTAG- Ho kena ho JTAG-OUT boemo ba ho sebelisa tšobotsi ena e fumanehang.
- Ho theha JTAG ketane ea daisy e sebelisang liboto tse ngata tsa ATF15xx-DK3, TDO Selection Jumper, e ngotsoeng JP-TDO, e tlameha ho behoa sebakeng se loketseng. Bakeng sa lisebelisoa tsohle tse ka har'a ketane ea daisy ntle le sesebelisoa sa ho qetela, jumper ena e tlameha ho hlongoa sebakeng sa TO NEXT DEVICE. Bakeng sa sesebelisoa sa ho qetela sa ketane, jumper ena e tlameha ho hlophisoa ho TO ISP CABLE boemo. Ha jumper ena e le maemong a TO NEXT DEVICE, TDO ea JTAG sesebelisoa se tla hokahana le TDI ea se latelang
- JTAG sesebelisoa ka ketane. Ha jumper ena e le maemong a TO ISP CABLE, TDO ea sesebelisoa seo e tla hokahanngoa le TDO ea J.TAG Sehokelo sa 10-pin, se tla lumella lets'oao la TDO la sesebelisoa se ka har'a ketane hore le fetisetsoe ho PC e amohelang ka software ea ISP. Setšoantšo se ka tlase ke setšoantšo sa potoloho ea
- JTAG lihokelo le jumper ea JP-TDO. Tafole e ka tlase e thathamisa linomoro tsa phini tsa JTAG lithapo tsa sesebelisoa sa ATF15xx lipaketeng tsohle tse fumanehang.
Bakeng sa ho seta sesebelisoa se le seng, boemo ba jumper ea JP-TDO bo tlameha ho hlophisoa ho TO ISP CABLE.
Setšoantšo sa 7. Setšoantšo sa Potoloho sa JTAG Lihokelo tsa ISP le TDO Jumper
- Lethathamo la 7.Pin Nomoro ea JTAG Lipontšo tsa Boema-kepe
| 44-pin TQFP | PLCC ea lintlha tse 44 | PLCC ea lintlha tse 84 | 100-pin TQFP | |
| TDI | 1 | 7 | 14 | 4 |
| TDO | 32 | 38 | 71 | 73 |
| TMS | 7 | 13 | 23 | 15 |
| TCK | 26 | 32 | 62 | 62 |
Algorithm ea ISP e laoloa ke software ea ATMISP, e sebetsang ho PC. Ba bane JTAG matšoao a hlahisoa ke boema-kepe ba LPT, 'me a ts'oaroa ke thapo ea download ea ISP pele a kena sesebelisoa sa ATF15xx ho boto ea CPLD Development/Programmer. Lipini tse 10 JTAG Pinaut ea Port Header ho boto ea CPLD Development/Programmer e bonts'itsoe ho Setšoantšo sa 8, le litekanyo tsa monna enoa ea 10-pin.TAG lihlooho li bontšitsoe setšoantšong sa 9.
Setšoantšo sa 8. 10-pin JTAG Port Header Pinout
- Lipini tse 10 JTAG Port Header pinout e tsamaisana le thapo e thehiloeng koung ea ATDH1150PC/VPC LPT le thapo e thehiloeng ho koung ea USB ea ATDH1150USB, hammoho le Altera.
- Lithapo tse thehiloeng boema-kepeng tsa ByteBlaster/MV/II LPT. Ntle le moo, software ea ATMISP v6.7 e lumella tšebeliso ea Atmel
- ATDH1150PC/VPC/USB cable kapa mohala oa ByteBlaster/MV/II ho kenya tšebetsong ISP.
- ATMISP v7.0 e ts'ehetsa thapo ea ATDH1150USB feela.
- Socket Adapter Board
- ATF15xx-DK3 CPLD Development/Programmer Socket Adapter Boards (ATF15xx-DK3-XXXXX) ke liboto tsa potoloho tse hokahanyang le ATF15xx-DK3 CPLD Development/Programme Board. Li sebelisoa 'moho le ATF15xx-DK3 CPLD Development/Programme Board ho lekola kapa ho hlophisa lisebelisoa tsa ATF15xx ISP CPLD ka mefuta e fapaneng ea liphutheloana. Ho na le Liboto tse 'ne tsa Socket Adapter tse fumanehang bakeng sa ATF15xx-DK3 tse koahelang 44-TQFP, 44-PLCC, 84-PLCC, le 100-
- Mefuta ea liphutheloana tsa TQFP lelapeng la ATF15xx la CPLDs.
- Boto e 'ngoe le e' ngoe ea socket adapter e na le sokete ea sesebelisoa sa ATF15xx 'me e na le lihlooho tsa banna ka tlase, tse ngotsoeng JP1 le JP2. Lihlooho tse lehlakoreng le ka tlase li kopane le lihlooho tsa basali holim'a boto ea ATF15xx-DK3, e ngotsoeng JP4 le JP3. Lipontšo tse 'ne tsa likarolo tse 7, li-switches tsa push-button,
- JTAG matšoao a koung, oscillator, VCCINT, VCCIO, le GND ho CPLD Development/Programmer Board li hokahane le sesebelisoa sa ATF15xx ho Socket Adapter Board ka lihlopha tsena tse peli tsa likhokahanyo.
- Ka holim'a adaptara ea socket ea 44-TQFP, ho na le likhokahano tse 'ne tsa 10-pin tse nang le litekanyo tse tšoanang le tsa J.TAG Sehokelo sa ISP. Lithakhisa tsa lihokelo tsena tse 'ne li hokahane le li-input le li-I/O (ntle le tse 'ne tsa JTAG pins) ea sesebelisoa sa CPLD se shebiloeng. Li ka sebelisoa ho hokahanya le oscilloscope kapa logic analyzer ho tšoara mesebetsi ea ho kenya letsoho le I / O pins ea CPLD. Li ka boela tsa sebelisoa ho hokahanya li-input le I/O pins tsa CPLD ho liboto tse ling tsa kantle kapa lisebelisoa bakeng sa tlhahlobo ea boemo ba sistimi kapa tlhahlobo.
- Atmel ATF15xx ISP Download Cable
- ATF15xx ISP Download Cable (P/N: ATDH1150VPC) e hokela kou ea LPT ea PC ho 10-pin J.TAG hlooho ho CPLD Development/Programmer Board kapa boto ea potoloho e tloaelehileng. Sena se bonts'itsoe ho Setšoantšo sa 10. Cable ena ea ISP e sebetsa e le buffer ho thibela JTAG matšoao pakeng tsa koung ea LPT ea PC le ATF15xx boto ea potoloho. The Power-On LED e ka morao ea ntlo ea sehokelo sa banna ba 25-pin e bontša hore thapo e hokahane hantle.
- Etsa bonnete ba hore LED ena e buletsoe pele u sebelisa Atmel CPLD ISP Software (ATMISP).
- Thapo ena ea ISP e na le sehokelo sa banna ba 25-pin (DB25), se hoketsoeng boema-kepeng ba LPT ba komporo. Polaka e tšehali ea lipini tse 10 e hokela ho 10-pin e tona JTAG hlooho ho boto ea potoloho ea ISP. Mothalo o mofubelu o holim'a thapo ea ribone o bontša moo pin 1 e leng teng ea polaka e tšehali. Monna ea lipini tse 10 JTAG hlooho ho CPLD
- Boto ea Ntlafatso / Lenaneo e arotsoe ho thibela basebelisi ho kenya polaka ea basali sebakeng se fosahetseng.
- Lisebelisoa tsa CPLD Development/Programmer li kenyelletsa Cable ea ATF15xx ISP Download
(ATDH1150VPC); leha ho le joalo, lithapo tse ling tse tšehelitsoeng tsa ISP le tsona li ka sebelisoa. Lithapo tsa ATDH1150VPC, ATDH1150USB, ByteBlasterMV, le ByteBlasterII li ka sebelisoa bakeng sa lisebelisoa tsa ATF15xx/ASL (5V) le ATF15xxASV/ASVL (3.3V), ha lithapo tsa khale tsa ATDH1150PC le ByteBlaster li ka sebelisoa bakeng sa lisebelisoa tsa ATF15x/TF5X (XNUMXx) feela.
- Setšoantšo sa 11 se bonts'a pinout ea lihlooho tsa basali tse 10 bakeng sa ATF15xx ISP Download Cable. Pinaut ea lihlooho tse 10 tsa banna ho PC board (haeba e sebelisoa bakeng sa ISP) e tlameha ho ts'oana le pinout ena.
- Hlokomela: Boto ea potoloho e tlameha ho fana ka VCC le GND ho CPLD ISP Cable ka hlooho ea banna ba 10-pin.
Litšoantšo tsa Schematic
Litšupiso le Tšehetso
Bakeng sa litšupiso tse eketsehileng tsa software ea moralo oa PLD le tšehetso, litokomane tse kang thuso files, tutorials, application notes/briefs, and user guides are available at www.atmel.com.
Atmel ProChip Designer Software
Letlapa la 8.ProChip Designer References le Tšehetso
| Moqapi oa ProChip | Ho tsoa ho menu e kholo ea fensetere ea ProChip… |
| Thusa | Khetha Thusa > Thuso ea Moqapi oa Prochip. |
| Lithupelo | Khetha Thusa > Lithupelo. |
| Mathata a tsejoang le tharollo | Khetha Thusa > Review KPS. |
Atmel WinCUPL Software
Letlapa la 9. Litšupiso tsa WinCUPL le Tšehetso
| WinCUPL | Ho tsoa ho menu ea WinCUPL ea mantlha… |
| Thusa | Khetha Thusa > Litaba. |
| CUPL Programmers Reference Guide | Khetha Thusa > CUPL Programmers Reference. |
| Lithupelo | Khetha Thusa > Atmel Info > Thupelo1.pdf. |
| Mathata a tsejoang le tharollo | Khetha Thusa > Atmel Info > CUPL_BUG.pdf. |
Atmel ATMISP Software
Lethathamo la 10. Litlhahiso le Tšehetso ea ATMISP
| ATMISP | Ho tsoa ho menu e kholo ea fensetere ea ATMISP… |
| Thusa Files | Khetha Thusa > Thuso ea ISP. |
| Lithupelo | Khetha Thusa > ATMISP Thuto. |
| Mathata a tsejoang le tharollo | U sebelisa sebatli sa Windows Explorer, fumana foldara ea ATMISP 'me u e bule balame.txt file ka mohlophisi oa mongolo oa ASCII. |
Atmel POF2JED Phetoho Software
Letlapa la 11. Litlhahiso le Tšehetso ea POF2JED
| POF2JED | Ho tsoa ho menu e kholo ea fensetere ea POF2JED… |
| Kakaretso ea Kopo ea Phetoho ea ATF15xx | Khetha Thusa > Likhetho tsa ho sokoloha. |
Tšehetso ea tekheniki
- Bakeng sa tšehetso ea tekheniki litabeng life kapa life tse amanang le Atmel PLD, ikopanye le Sehlopha sa Likopo sa Atmel PLD ho:
- Email pld@atmel.com
- Mohala (+1)408-436-4333
- Foromo ea Tšehetso ea Inthaneteng http://support.atmel.com/bin/customer.exe
Nalane ea Phetoho
| Khatiso | Letsatsi | Tlhaloso |
| 3605C | 06/2014 | Ntlafatsa meralo, template, li-logo, le leqephe la boithomelo. Kenya karolo ea Histori ea Phetoho. |
| 3605B | 05/2008 |
- Atmel Corporation 1600 Technology Drive, San Jose, CA 95110 USA T: (+1)(408) 441.0311 F: (+1)(408) 436.4200 | www.atmel.com
- © 2014 Atmel Corporation. / Rev.: Atmel-3605C-CPLD-ATF15xx-DK3-Development-Kit-UserGuide_062014.
- Atmel®, logo ea Atmel le metsoako ea eona, Ho nolofalletsa menyetla e sa lekanyetsoang, le tse ling ke matšoao a ngolisitsoeng kapa matšoao a khoebo a Atmel Corporation naheng ea Amerika.
linaha tse ling. Mabitso a mang le mabitso a lihlahisoa e kanna ea ba matšoao a ba bang. - TLHOKOMELO: Lintlha tse tokomaneng ena li fanoe mabapi le lihlahisoa tsa Atmel. Ha ho laesense, e hlalositsoeng kapa e boletsoeng, ka estoppel kapa ka tsela e 'ngoe, ho tokelo efe kapa efe ea thepa ea mahlale e fanoeng ke tokomane ena kapa mabapi le thekiso ea lihlahisoa tsa Atmel.
- NTLE JOALOKAHA HO BEHILE MELAO LE MAEMO A ATMEL TSA THEKISO E FUMANEHANG HO ATMEL. WEBSEBAKA, ATMEL HA E NKA MOTHO EFE LE EFE HONA E HLOKOMELA KA HO BONAHALA, HO FINYELLANG, KAPA TIISETSO E MOLAO E MABAPI LE LIHLAHISO TSA LONA, EMPA E SA LEKELETSO, TIISETSO E FUMANETSOENG EA THEKISO, HO TŠOANELEHA, HO SEBELISA MOSEBETSI OA SEBAKA. IN
- HA HO KETSAHALO E TLA IKOLA MOLATO O MONG O MONG O MONG O MANG KA MONG O MONG O MONG O MONG O MONG O MONG O MANG, O A HLAHANG, OA KOTSO, O KHETHEHILENG, KAPA OA TSHOANELO (Ho kenyeletsoa, Ntle le Meedi, Tšenyo BAKENG SA TAHLEHELO LE PHAELE, TŠITISO EA LIKHOEBO, KAPA TAHLEHO EA TŠEBELETSO) TOKOMANE ENA, LE HA ATMEL E NE E ELETSWA KA MOKGWA OA TSAMAISO E JALO.
- Atmel ha e etse tlhahiso kapa litiisetso mabapi le ho nepahala kapa botlalo ba litaba tsa sena
tokomane mme o na le tokelo ea ho etsa liphetoho ho litlhaloso le litlhaloso tsa sehlahisoa ka nako efe kapa efe ntle le tsebiso. Atmel ha e etse boitlamo bofe kapa bofe ba ho nchafatsa tlhahisoleseling e fanoeng mona. Ntle le ha ho fanoe ka mokhoa o mong, lihlahisoa tsa Atmel ha li tšoanelehe, 'me li ke ke tsa sebelisoa, lits'ebetsong tsa likoloi. Lihlahisoa tsa Atmel ha lia rereloa, ha lia lumelloa, kapa ha lia fuoa tumello ea ho sebelisoa e le likarolo tsa lits'ebetso tse reretsoeng ho tšehetsa kapa ho boloka bophelo. - TLHOKOMELISO EA TŠEBELETSO, EA SESOLE, LE EA MOSEBETSI OA MOSEBETSI: Lihlahisoa tsa Atmel ha lia etsetsoa ebile li ke ke tsa sebelisoa mabapi le lits'ebetso leha e le life moo ho hlōleha ha lihlahisoa tse joalo ho ka lebelloang ho baka kotsi e kholo ea botho kapa lefu ("Safety-Critical Applications") ntle le lengolo le tobileng la ofisiri ea Atmel.
- tumello. Polokeho-Bohlokoa Likopo li kenyelletsa, ntle le meeli, lisebelisoa tsa ts'ehetso ea bophelo, le litsamaiso, lisebelisoa kapa litsamaiso tsa ts'ebetso ea meaho ea nyutlelie le litsamaiso tsa libetsa.
- Lihlahisoa tsa Atmel ha lia etsetsoa kapa hona ho rereloa ho sebelisoa lits'ebetsong tsa sesole kapa tsa sefofane kapa tikoloho ntle le haeba Atmel e khethiloe ka ho khetheha e le boemo ba sesole. Lihlahisoa tsa Atmel ha lia etsetsoa kapa hona ho rereloa ho sebelisoa lits'ebetsong tsa likoloi ntle le haeba li khethiloe ke Atmel joalo ka boemo ba likoloi.
- E jarollotsoe ho: Arrow.com.
Litokomane / Lisebelisoa
 |
Atmel ATF15xx-DK3 CPLD Ntshetsopele / Setsi sa Lenaneo [pdf] Bukana ea Mosebelisi ATF15xx-DK3 CPLD Development Programmer Kit, ATF15xx-DK3, CPLD Development Programmer Kit, Development Programmer Kit, Programmer Kit |
