Atmel ATF15xx-DK3 CPLD Mmepe/ Ngwa ihe mmemme
Okwu mmalite
Ngwa Atmel® ATF15xx-DK3 Complex Programmable Logic Device (CPLD) Development/Programmer Kit bụ usoro mmepe zuru oke yana mmemme In-System Programming (ISP) maka Atmel ATF15xx Ezinụlọ nke ụlọ ọrụ ọkọlọtọ pin dakọtara CPLDs nwere atụmatụ Logic Doubling®. Ngwa a na-enye ndị na-emepụta ụzọ ngwa ngwa na ụzọ dị mfe iji mepụta prototype na nyochaa atụmatụ ọhụrụ site na iji ATF15xx ISP CPLD. Ezinụlọ ATF15xx nke ISP CPLDs gụnyere Atmel ATF15xxAS, ATF15xxASL, ATF15xxASV, na ATF15xxASVL CPLDs. Site na ịnweta bọọdụ nkwụnye nkwụnye dị iche iche iji kwado ọtụtụ ụdị ngwugwu (1) enyere na ATF15xx Ezinụlọ nke ISP CPLDs, enwere ike iji ngwa a dị ka onye mmemme ISP iji hazie ATF15xx ISP CPLDs n'ọtụtụ ụdị ngwugwu dị. (1) site na ọkọlọtọ ụlọ ọrụ JTAG interface (IEEE 1149.1).
Ọdịnaya ngwa
- Atmel CPLD Development/Boọdụ mmemme (P/N: ATF15xx-DK3)
- Atmel 44-pin TQFP Socket Adapter Board (P/N: ATF15xx-DK3-SAA44)(2)
- Atmel ATF15xx LPT dabere na JTAG Igwe nbudata ISP (P/N: ATDH1150VPC)
- Abụọ Atmel 44-pin TQFP Sampna Ngwaọrụ
Nkwado ngwaọrụ
Ngwa ATF15xx-DK3 CPLD Development/Programmer Kit na-akwado ngwaọrụ ndị a na akararị ọsọ Atmel na ngwugwu niile dị ugbu a (ma ewezuga 100-PQFP):
- ATF1502AS/ASL
- ATF1504AS/ASL
- ATF1508ASV/ASVL
- ATF1502ASV
- ATF1504ASV/ASVL
- ATF1508AS/ASL
- A naghị enye bọọdụ nkwụnye nkwụnye maka 100-pin PQFP.
- Naanị 44-pin TQFP Socket Adapter Board esonye na ngwa a. A na-ere bọọdụ nkwụnye nkwụnye ndị ọzọ iche iche. Hụ Nkebi, “Nkọwa akụrụngwa” maka ozi ndị ọzọ na bọọdụ nkwụnye nkwụnye ịtụ koodu.i
Njirimara ngwa
Board Development/Programmer CPLD
- 10-pin JTAG-ISP Port
- Sekit Nnyefe Ike achịziri maka isi iyi ike 9VDC
- 5V, 3.3V, 2.5V, ma ọ bụ 1.8VI/O Voltage Tụkwasịnụ
- 1.8V, 3.3V, ma ọ bụ 5.0V Core Voltage Tụkwasịnụ
- 44-pin TQFP Socket Adapter Board
- Ntụnye isi maka ntụtụ I/O nke ngwaọrụ ATF15xx
- 2MHz Crystal oscillator
- Ngosipụta LED akụkụ anọ 7
- Igwe ọkụ nke mmadụ asatọ
- Mgbanwe bọtịnụ ịpị asatọ
- Kpọchapụta zuru ụwa ọnụ yana mpụta Kwado bọtịnụ Push
- Ndị na-atụ ihe ugbu a
Ihe mgbagha CPLDs na-eme okpukpu abụọ
ATF15xx ISP CPLD nwere Logic Doubling Architecture
- Igwe nbudata ATF15xx ISP
- 5V, 3.3V, 2.5V, ma ọ bụ 1.8V ISP Download Cable maka PC Parallel Printer (LPT) Port
- Ngwa mmepe PLD
- Ngwa ngwanrọ mmepe Atmel PLD dị na ntanetị maka ndị nrụpụta PLD ji ATF15xx ISP CPLDs. Biko rụtụ aka na Overview akwụkwọ, "PLD
- Design Software karịrịview” dị na:
- http://www.atmel.com/images/atmel-3629-pld-design-software-overview.pdf
Achọrọ Sistemụ
- Obere ngwaike na ngwanrọ achọrọ iji hazie ngwaọrụ ATF15xx ISP CPLD nke emebere site na iji Atmel ProChip Designer Software na CPLD Development/Programmer Board site na Atmel ATMISP v6.x (ATF15xx CPLD ISP Software) bụ:
- x86 Kọmputa dabere na Microprocessor
- Windows XP®, Windows® 98, Windows NT® 4.0, ma ọ bụ Windows 2000
- 128-MByte RAM
- Oghere diski ike 500 MByte efu
- Òké na-akwado Windows
- Ọdụ ụgbọ mmiri Parallel Printer (LPT) dị
- Ntinye ike 9VDC nwere 500mA nke ntinye ugbu a
- Nyochaa SVGA (Mkpebi 800 x 600)
Ozi ịtụ
| Nọmba akụkụ Atmel | Nkọwa |
| ATF15xx-DK3 | Ngwa Mmepe/Programmer CPLD (gụnyere ATF15xxDK3-SAA44*) |
| ATF15xxDK3-SAA100 | 100-pin TQFP Socket Adapter Board maka bọọdụ DK3 |
| ATF15xxDK3-SAJ44 | 44-pin PLCC Socket Adapter Board maka DK3 Board |
| ATF15xxDK3-SAJ84 | 84-pin PLCC Socket Adapter Board maka DK3 Board |
| ATF15xxDK3-SAA44* | 44-pin TQFP Socket Adapter Board maka bọọdụ DK3 |
Nkọwa ngwaike
Board Development/Programmer CPLD
- CPLD Development/Programmer na Socket Adapter Board nke egosiri n'ọnụọgụ dị n'okpuru nwere atụmatụ bara uru maka ịmepụta, imepụta ihe, ma ọ bụ nyocha.
- ATF15xx CPLD aghụghọ. Akụkụ ndị na-eme ka nke a bụrụ ngwa mmalite/mmepe ngwa ngwa yana ihe mmemme ISP maka ezinụlọ ATF15xx nke J.TAG-ISP CPLDs gụnyere:
- Mgbanwe bọtịnụ pịa
- Igwe ọkụ
- Ngosipụta akụkụ 7
- 2MHz Crystal oscillator
- 5V, 3.3V, 2.5V, ma ọ bụ 1.8V VCCIO Nhọrọ
- 1.8V, 3.3V, ma ọ bụ 5.0V VCINT Nhọrọ
- JTAG ISP Port
- Ihe nkwụnye nkwụnye
- Ihe ngosi 7-ngalaba nwere ndị na-akpụ akpụ nwere ike ịhọrọ
- Board Development/Programmer CPLD nwere ngosipụta akụkụ anọ nke na-enye ohere nlele nke ATF7xx CPLD. Ngosipụta anọ a ka akpọrọ DSP15, DSP1, DSP2, na DSP3. Ngosipụta akụkụ 4 nwere LED anode nkịtị nwere ahịrị anode nkịtị jikọtara na VCCIO (I/O ọkọnọ vol.tage maka CPLD) site na usoro nke resistors nwere jumpers a na-ahọrọ nke akpọrọ JPDSP1, JPDSP2, JPDSP3, na JPDSP4. Enwere ike iwepụ jumpers ndị a
gbanyụọ ngosi site na ịtọghe VCCIO na ngosipụta. Ejikọrọ ahịrị cathode n'otu n'otu na ntụtụ I/O nke ATF15xx CPLD na CPLD - Ngwa mmepe/ihe mmemme. Ka ịgbanwuo otu akụkụ, gụnyere DOT nke ngosi, ATF15xx I / O pin kwekọrọ na nke a LED ga-abụrịrị na ezi uche dị ala nke nwere usoro jumper nwere ike ịhọrọ; ya mere, ntinye nke ngwaọrụ ATF15xx ga-achọ nhazi maka ntinye ọrụ-dị ala na nhazi file. Ngosipụta na-arụ ọrụ kacha mma na 2.5V VCCIO ma ọ bụ karịa.
- Akụkụ nke ọ bụla nke ngosipụta ọ bụla bụ nke siri ike na-agbanye n'otu pin I/O kpọmkwem nke ngwaọrụ ATF15xx. Maka ngwaọrụ ọnụ ọgụgụ dị elu (100-pin na ibu), akụkụ asaa niile na akụkụ DOT nke ihe ngosi anọ jikọtara na pin I / O; Otú ọ dị, maka ngwaọrụ ọnụ ọgụgụ dị ala, ọ bụ naanị obere akụkụ nke ngosipụta, ngosipụta nke mbụ na nke anọ, ka ejikọrọ na ntụtụ I/O nke ngwaọrụ ATF15xx. Tebụlụ 1 na 2 na-egosi njikọ ngwungwu ihe ngosi 7 na ngwaọrụ ATF15xx. E gosipụtara atụmatụ sekit nke ihe ngosi na jumpers na foto dị n'okpuru.
Ọgụgụ 2. Ihe osise okirikiri nke Ngosipụta akụkụ 7 na jumpers
Tebụl 1.ATF15xx Njikọ 44-pin na ngosipụta akụkụ 7
| 44-pin TQFP | |||
| DSP/Ngalaba | PLD pin | DSP/Ngalaba | PLD pin |
| 1/A | 27 | 3/A | NC |
| 1/B | 33 | 3/B | NC |
| 1/C | 30 | 3/C | NC |
| 1/D | 21 | 3/D | NC |
| 1/E | 18 | 3/E | NC |
| 1/F | 23 | 3/F | NC |
| 1 G | 20 | 3 G | NC |
| 1/DOT | 31 | 3/DOT | NC |
| 2/A | NC | 4/A | 3 |
| 2/B | NC | 4/B | 10 |
| 2/C | NC | 4/C | 6 |
| 2/D | NC | 4/D | 43 |
| 2/E | NC | 4/E | 35 |
| 2/F | NC | 4/F | 42 |
| 2 G | NC | 4 G | 34 |
| 2/DOT | NC | 4/DOT | 11 |
| 44-pin PLCC | |||
| DSP/Ngalaba | PLD pin | DSP/Ngalaba | PLD pin |
| 1/A | 33 | 3/A | NC |
| 1/B | 39 | 3/B | NC |
| 1/C | 36 | 3/C | NC |
| 1/D | 27 | 3/D | NC |
| 1/E | 24 | 3/E | NC |
| 1/F | 29 | 3/F | NC |
| 1 G | 26 | 3 G | NC |
| 1/DOT | 37 | 3/DOT | NC |
| 2/A | NC | 4/A | 9 |
| 2/B | NC | 4/B | 16 |
| 2/C | NC | 4/C | 12 |
| 2/D | NC | 4/D | 5 |
| 2/E | NC | 4/E | 41 |
| 2/F | NC | 4/F | 4 |
| 2 G | NC | 4 G | 40 |
| 2/DOT | NC | 4/DOT | 17 |
Tebụl 2.ATF15xx 84-pin na 100-pin Njikọ na ngosipụta akụkụ 7
| 84-pin PLCC | |||
| DSP/Ngalaba | PLD pin | DSP/Ngalaba | PLD pin |
| 1/A | 68 | 3/A | 22 |
| 1/B | 74 | 3/B | 28 |
| 1/C | 70 | 3/C | 25 |
| 1/D | 63 | 3/D | 21 |
| 1/E | 58 | 3/E | 16 |
| 1/F | 65 | 3/F | 17 |
| 1 G | 61 | 3 G | 12 |
| 1/DOT | 73 | 3/DOT | 29 |
| 2/A | 52 | 4/A | 5 |
| 2/B | 57 | 4/B | 10 |
| 2/C | 55 | 4/C | 8 |
| 2/D | 48 | 4/D | 79 |
| 2/E | 41 | 4/E | 76 |
| 2/F | 50 | 4/F | 77 |
| 2 G | 45 | 4 G | 75 |
| 2/DOT | 50 | 4/DOT | 11 |
| 100-pin TQFP | |||
| DSP/Ngalaba | PLD pin | DSP/Ngalaba | PLD pin |
| 1/A | 67 | 3/A | 13 |
| 1/B | 71 | 3/B | 19 |
| 1/C | 69 | 3/C | 16 |
| 1/D | 61 | 3/D | 8 |
| 1/E | 57 | 3/E | 83 |
| 1/F | 64 | 3/F | 6 |
| 1 G | 60 | 3 G | 92 |
| 1/DOT | 75 | 3/DOT | 20 |
| 2/A | 52 | 4/A | 100 |
| 2/B | 54 | 4/B | 94 |
| 2/C | 47 | 4/C | 97 |
| 2/D | 41 | 4/D | 81 |
| 2/E | 46 | 4/E | 76 |
| 2/F | 40 | 4/F | 80 |
| 2 G | 45 | 4 G | 79 |
| 2/DOT | 56 | 4/DOT | 93 |
LEDs nwere ndị jumpers a na-ahọrọ
CPLD Development/Programmer Board nwere LED asatọ n'otu n'otu, nke na-enye ndị na-emepụta ohere igosipụta akara mmepụta sitere na onye ọrụ I / Os nke ngwaọrụ ATF15xx. A na-akpọ ọkụ ọkụ asatọ a LED1 ruo LED8 na CPLD Development/Programmer Board. A na-ejikọta cathode nke LED ọ bụla na Ground (GND) site na usoro resistor, ebe anode nke LED ọ bụla jikọọ na onye ọrụ I / O pin nke CPLD site na JPL1/2/3/4/5/6/7 /8 jumper nwere ike ịhọrọ. Enwere ike iwepụ ndị a jumpers iji gbanyụọ LEDs site na-ejikọta anodes nke LED na pin I / O nke CPLD. Ọnụ ọgụgụ dị n'okpuru ebe a na-egosi eserese sekit nke LED na ndị jumpers nhọrọ.
Iji gbanye otu ọkụ ọkụ, pin ATF15xx I / O kwekọrọ na LED ga-adịrịrị n'ọnọdụ dị elu nke nwere usoro jumper kwekọrọ; ya mere, ihe nrụpụta nke ngwaọrụ ATF15xx ga-adị mkpa ka ahazi ya dị ka mmepụta dị elu na-arụ ọrụ. Igwe ọkụ na-arụ ọrụ kacha mma na 2.5V VCCIO ma ọ bụ karịa.
Ngwaọrụ ọnụ ntụtụ dị ala (44-pin) nwere naanị I/Os anọ ejikọrọ na LED1/2/3/4. Maka ngwaọrụ ọnụ ọgụgụ dị elu (100-pin na ibu), ọkụ asatọ niile jikọtara na I/O nke ngwaọrụ ahụ. Tebụl 3 na-egosi njikọ ngwugwu dị iche iche nke CPLD I/Os na LEDs.
Tebụl 3.ATF15xx Njikọ na LEDs
| 44-pin TQFP | |
| Ikanam | PLD pin |
| LED1 | 28 |
| LED2 | 25 |
| LED3 | 22 |
| LED4 | 19 |
| 44-pin PLCC | |
| Ikanam | PLD pin |
| LED1 | 34 |
| LED2 | 31 |
| LED3 | 28 |
| LED4 | 25 |
| 84-pin PLCC | |
| Ikanam | PLD pin |
| LED1 | 69 |
| LED2 | 67 |
| LED3 | 64 |
| LED4 | 60 |
| LED5 | 27 |
| LED6 | 24 |
| LED7 | 18 |
| LED8 | 15 |
| 100-pin TQFP | |
| Ikanam | PLD pin |
| LED1 | 68 |
| LED2 | 65 |
| LED3 | 63 |
| LED4 | 58 |
| LED5 | 17 |
| LED6 | 14 |
| LED7 | 10 |
| LED8 | 9 |
Mgbanwe bọtịnụ na-eji ihe ndị nwere ike ịhọrọ maka mkpọ I/O
- Board Development/Programmer CPLD nwere bọtịnụ push-bọtịnụ asatọ, nke ejikọrọ na ntụtụ I/O nke CPLD. Mgbanwe ndị ahụ na-eziga akara mgbanaka ntinye aka na ntụtụ I/O nke ngwaọrụ ATF15xx onye ọrụ. Akpọrọ mgba ọkụ ndị a SW1 gaa SW8 na CPLD Development/Programmer
bọọdụ. A na-ejikọta otu njedebe nke bọtịnụ ntinye ntinye ọ bụla na VCCIO, ebe njedebe nke ọzọ nke bọtịnụ ntinye ọ bụla na-ejikọta ya na ihe mgbochi mgbada wee jikọọ ya na pin I / O kpọmkwem nke CPLD site na JPS1/2. /3/4/5/6/7/8 jumper nwere ike họrọ. - Ọ bụrụ na a pịa nke ọ bụla n'ime mgba ọkụ ndị a ma tinye jumper kwekọrọ, a ga-ebuba pin I / O kpọmkwem nke ngwaọrụ ahụ gaa n'ọnọdụ dị elu nke mgbagha site na mmepụta nke sekit mgba ọkụ. Ebe ọ bụ na a na-ejikọkwa bọtịnụ push-button ọ bụla na resistor na-agbada, ntinye ahụ ga-enwe ọnọdụ mgbagha dị ala ma ọ bụrụ na agbanyeghi mgba ọkụ ahụ na ntọala jumper kwekọrọ. Ọ bụrụ na edobeghi bọtịnụ push-button, a ga-ewere ntụtụ kwekọrọ dị ka ntụtụ enweghị njikọ. Ọgụgụ 4 bụ eserese sekit nke ngbanwe bọtịnụ push na jumper a na-ahọrọ. Tebụl 4 na-egosi njikọ nke bọtịnụ ntinye asatọ a na-atụgharị na ntụtụ CPLD I/O na ụdị ngwugwu dị iche iche.
Tebụl 4.ATF15xx Njikọ na I/O Pin Switches
| 44-pin TQFP | |
| Pịa bọtịnụ | PLD pin |
| SW1 | 15 |
| SW2 | 14 |
| SW3 | 13 |
| SW4 | 12 |
| SW5 | 8 |
| SW6 | 5 |
| SW7 | 2 |
| SW8 | 44 |
| 44-pin PLCC | |
| Pịa bọtịnụ | PLD pin |
| SW1 | 21 |
| SW2 | 20 |
| SW3 | 19 |
| SW4 | 18 |
| SW5 | 14 |
| SW6 | 11 |
| SW7 | 8 |
| SW8 | 6 |
| 84-pin PLCC | |
| Pịa bọtịnụ | PLD pin |
| SW1 | 54 |
| SW2 | 51 |
| SW3 | 49 |
| SW4 | 44 |
| SW5 | 9 |
| SW6 | 6 |
| SW7 | 4 |
| SW8 | 80 |
| 100-pin TQFP | |
| Pịa bọtịnụ | PLD pin |
| SW1 | 48 |
| SW2 | 36 |
| SW3 | 44 |
| SW4 | 37 |
| SW5 | 96 |
| SW6 | 98 |
| SW7 | 84 |
| SW8 | 99 |
Mgbanwe bọtịnụ na-eji ihe ndị nwere ike ịhọrọ maka GCLR na OE1 Pin
CPLD Development/Programmer Board nwere bọtịnụ push-bọtịnụ abụọ maka ntụtụ Global Clear (GCLR) na mmepụta Enable (OE1) nke CPLD. Mgbanwe ndị ahụ na-achịkwa steeti mgbagha nke ntinye OE1 na GCLR nke ngwaọrụ ATF15xx. A na-akpọ ọkụ ọkụ ndị a SW-GCLR na SW-GOE1 na bọọdụ. Otu njedebe nke mgba ọkụ ntinye ntinye SW-GCLR ka ejikọrọ na GND. Ọgwụgwụ nke ọzọ
ejikọrọ ngbanwe bọtịnụ push-up resistor na VCCIO wee jikọọ ya na pin ntinye ntinye raara onwe ya nye GCLR nke ngwaọrụ ATF15xx. Ezubere ya ka ejiri ya dị ka mgbaama nrụpụta nrụpụta dị ala na-arụ ọrụ iji tọgharịa ndebanye aha na ngwaọrụ ATF15xx yana usoro jumper nhọrọ nke JPGCLR. N'otu aka ahụ, otu njedebe nke SW-GOE1 ntinye bọtịnụ ntinye ntinye na GND. Nkwụsị nke ọzọ nke ngbanwe bọtịnụ ntinye
ejikọrọ na resistor ndọpụ na VCCIO wee jikọọ na OE1 ntinye ntinye raara onwe ya nye nke ngwaọrụ ATF15xx. Ezubere ya ka ejiri ya dị ka ihe nrụpụta dị ala na-arụ ọrụ na-enye ohere iji chịkwaa ikike/ịgbanyụọ ihe nrụpụta steeti atọ dị na ATF15xx yana JPGOE họrọ jumper set. Onyonyo 5 bụ eserese sekit nke ngbanwe bọtịnụ push-button na jumpers maka ntụtụ GCLR na OE1.
Ọ bụrụ na agbanye nke ọ bụla n'ime bọtịnụ push-bọtịnụ ndị a ma hazie jumper kwekọrọ, a ga-ebuba I/O nke CPLD gaa na steeti dị ala. Ebe ọ bụ na a na-ejikọkwa bọtịnụ push-elu na resistor na-adọta, ntinye CPLD kwekọrọ ga-enwe ọnọdụ dị elu dị elu ma ọ bụrụ na agbanyeghi bọtịnụ push-bọtịnụ ya na setịpụ jumper nhọrọ dabara adaba. Ọ bụrụ na edobeghi jumper nke nwere ike họrọ, pin ntinye raara onwe ya nye kwekọrọ nke CPLD nwere ike were ya dị ka pin No Connect (NC). Tebụl 5 na-egosi ntụtụ pin nke GCLR na OE1 ntinye ntinye nke ngwaọrụ ATF15xx n'ụdị ngwugwu niile dị.
Onyonyo 5. Ihe onyonyo sekit nke mgbanwe bọtịnụ Push na ihe ndị a na-ahọrọ maka GCLR na OE1
Tebụl 5.Pin Ọnụọgụ GCLR na OE1
| 44-pin TQFP | 44-pin PLCC | 84-pin PLCC | 100-pin TQFP | |
| GCLR | 39 | 1 | 1 | 89 |
| OE1 | 38 | 44 | 84 | 88 |
2MHz Oscillator na Nhọrọ elekere
The Clock Selection Jumper nke akpọrọ JP-GCLK na CPLD Development/Programmer Board bụ jumper ọnọdụ abụọ na-enye ndị ọrụ ohere ịhọrọ pin ntinye GCLK raara onwe ya nye (ma GCLK1 ma ọ bụ GCLK2) nke ATF15xx ngwaọrụ kwesịrị jikọọ na mmepụta nke 2MHz oscillator. Na mgbakwunye, enwere ike iwepụ jumper ka ikwe ka ejikọta isi iyi elekere mpụga na GCLK1 na/ma ọ bụ GCLK2 nke ngwaọrụ ATF15xx. Ọgụgụ 6 bụ ihe atụ nke eserese sekit nke oscillator na jumper nhọrọ. Tebụl 6 na-egosi ọnụọgụ pin maka GCLK1 na GCLK2 ntinye ntinye nke ngwaọrụ ATF15xx n'ụdị ngwugwu dị iche iche dị.
Ọ bụrụ na edobere jumper GCLK1, jumper ga-adị n'akụkụ akụkụ osisi ahụ. N'aka nke ọzọ, ọ bụrụ na edobere GCLK2 jumper, jumper ga-adị n'etiti etiti ahụ.
Tebụl 6.Pin Ọnụọgụ nke GCLK1 na GCLK2
| 44-pin TQFP | 44-pin PLCC | 84-pin PLCC | 100-pin TQFP | |
| GCLK1 | 37 | 43 | 83 | 87 |
| GCLK2 | 40 | 2 | 2 | 90 |
VCCIO na VCINT Voltage Nhọrọ jumpers na LEDs
- VCCIO na VCINT Voltage Nhọrọ Jumpers, nke akpọrọ VCCIO Selector na VCCINT Selector n'otu n'otu na ATF15xx-DK3 Development/Programming Kit, kwe ka nhọrọ nke ọkọnọ I/O.
- voltage larịị (VCCIO) na isi ọkọnọ voltage larịị (VCCINT) nke a na-eji maka CPLD ebumnuche na ngwa. Ozugbo edobere jumpers ndị a nke ọma, LEDs (akpọrọ VCCINT LED na VCCIO LED) ga-agbanye; Otú ọ dị, na obere ọkọnọ voltage ọkwa (ya bụ 2.5V ma ọ bụ nke dị ala), LEDs nwere ike ịdị ntakịrị.
- Maka ATF15xxAS/ASL (5.0V) CPLDs, ma VCCIO Selector na VCCINT Selector jumpers ga-edozirịrị ka 5.0V.
- Maka ATF15xxASV/ASVL (3.3V) CPLDs, ma VCCIO Selector na VCCIN Selector Jumpers ga-edozirịrị ka ọ bụrụ naanị 3.3V.
- A ghaghị gbanyụọ ike nke CPLD Development/Programmer Kit mgbe ị na-agbanwe ọnọdụ nke VCCIO ma ọ bụ VCCINT Vol.tage Nhọrọ Jumper (VCCIO Selector ma ọ bụ VCINT Selector).
- ICCIO na ICCNT jumpers
- Enwere ike iwepụ ICCIO na ICCNT jumpers ma jiri ya mee ihe dị ka ihe nleba anya ICC. Mgbe ewepụrụ jumpers, mita dị ugbu a nwere ike jikọọ na posts iji tụọ oriri ugbu a nke CPLD lekwasịrị anya. Mgbe ndị ọrụ anaghị eji jumpers a tụọ ihe dị ugbu a, a ga-edozirịrị jumpers ndị a ka ngwa na CPLD rụọ ọrụ.
- Voltage Regulators
- Abụọ voltage regulators, nke akpọrọ VR1 na VR2, ka a na-eji na-ewepụta onwe ya ma na-ahazi
- VCCINT na VCCIO voltages si na 9VDC ike ọkọnọ. Maka nkọwapụta, biko hụ ATF15xx-DK3 kit schematic, eserese 12.
- Ọkụ na-enye ọkụ na ọkụ LED
- Enwere ike ịgbanye ọkụ na-enye ọkụ, nke akpọrọ POWER SWITCH, gaa na ịgbanwuo ma ọ bụ gbanyụọ, nke a na-eji gbanye ma ọ bụ gbanyụọ ike nke bọọdụ ATF15xx-DK3 n'otu n'otu. Ọ na-enye ohere 9VDC voltage na Jack na-enye ike ịgafe na voltage regulators mgbe ọ nọ na ọnọdụ. Mgbe agbanwuru ọkụ na-enye ọkụ, ọkụ ọkụ (akpọrọ POWER LED) ga-enwupụta iji gosi na a na-enye ngwa ATF15xx-DK3 na ike.
- Jack na-enye ike na isi ihe na-enye ike
- Bọdụ ATF15xx-DK3 nwere ụdị njikọ ọkọnọ ike abụọ dị iche iche nke akpọrọ JPower na JP Power. Enwere ike iji nke ọ bụla n'ime njikọ ọkọnọ ike a jikọọ isi iyi ike 9VDC na ngwa ahụ. Njikọ ike nke mbụ akpọrọ JPower, bụ jakị ike gbọmgbọm nwere post dayameta 2.1mm, ọ jikọtara ya na plọg nwanyị 2.1mm (dayameta dị n'ime) x 5.5mm (dayameta mpụta). Igwe ọkụ ọkụ nke abụọ akpọrọ JP Power, bụ nkụnye eji isi mee 4-pin nwoke 0.100 ″ nwere oghere 0.025 ″ square. Ịnweta ụdị njikọ ọkụ abụọ a na-enye ndị ọrụ ohere ịhọrọ ụdị akụrụngwa ọkụ ọkụ ga-eji maka ATF15xx-DK3 Development/Programmer Kit.
- Naanị otu n'ime njikọ ọkụ abụọ a kwesịrị iji isi iyi 9VDC kwadoro mana ọ bụghị ha abụọ n'otu oge.
- JTAG Njikọ ISP na TDO Nhọrọ Jumper
- Ihe JTAG Njikọ ISP aha JTAG-IN, eji jikọọ ATF15xx JTAG ntụtụ ọdụ ụgbọ mmiri (TCK, TDI, TMS, na TDO) site na eriri nbudata ISP gaa n'ọdụ ụgbọ mmiri PC maka J.TAG Mmemme ISP nke ngwaọrụ ATF15xx. A na-eji njikọ ndị nwere polarized na ATF15xx-DK3 na ISP Download Cable iji belata nsogbu njikọ. Ihe akara PIN1 dị na ala nke JTAG Njikọ ISP na-egosi ọnọdụ pin 1 nke nkụnye eji isi mee 10-pin wee belata ohere nke ijikọ ISP Download Cable na-ezighi ezi.
- N'aka ekpe nke JTAG-IN njikọ, enwere ogidi abụọ nke vias, a na-akpọkwa ha JTAG-Apụọ. E bu n'obi ka ha mee ka ndị ọrụ mepụta JTAG daisy chain ime JTAG arụmọrụ ka otutu ngwaọrụ. Ndị ọrụ ga-achọ ire otu ụdị njikọ dị ka nke ejiri maka JTAG-N'ime JTAG-OUT ọnọdụ iji jiri atụmatụ a dị.
- Iji mepụta JTAG yinye daisy na-eji ọtụtụ bọọdụ ATF15xx-DK3, TDO Nhọrọ Jumper, nke akpọrọ JP-TDO, ga-edozirịrị n'ọnọdụ kwesịrị ekwesị. Maka ngwaọrụ niile dị na yinye daisy ma e wezụga ngwaọrụ ikpeazụ, a ga-edobe jumper a na ọnọdụ ngwaọrụ ọzọ. Maka ngwaọrụ ikpeazụ dị n'agbụ a, a ga-edozi jumper a na ọnọdụ TO ISP CABLE. Mgbe jumper a nọ na ọnọdụ ngwaọrụ ọzọ, TDO nke otu JTAG a ga-ejikọta ngwaọrụ na TDI nke ọzọ
- JTAG ngwaọrụ na yinye. Mgbe jumper a nọ na ọnọdụ TO ISP CABLE, TDO nke ngwaọrụ ahụ ga-ejikọta na TDO nke J.TAG Njikọ 10-pin, nke ga-eme ka akara TDO nke ngwaọrụ ahụ dị n'agbụ ahụ laghachi na PC na-akwado ya na ngwa ISP. Ọnụ ọgụgụ dị n'okpuru bụ eserese sekit nke
- JTAG njikọ na JP-TDO jumper. Tebụlụ dị n'okpuru na-edepụta nọmba pin nke anọ JTAG atụdo maka ngwaọrụ ATF15xx na ngwugwu niile dị.
Maka otu ntọlite ngwaọrụ, ọnọdụ JP-TDO jumper ga-edorịrị na TO ISP CABLE.
Onyonyo 7. Ihe osise sekit nke JTAG Njikọ ISP na TDO Jumper
- Tebụl 7. Onu ogugu nke JTAG Mgbama ọdụ ụgbọ mmiri
| 44-pin TQFP | 44-pin PLCC | 84-pin PLCC | 100-pin TQFP | |
| TDI | 1 | 7 | 14 | 4 |
| TDO | 32 | 38 | 71 | 73 |
| TMS | 7 | 13 | 23 | 15 |
| TCK | 26 | 32 | 62 | 62 |
Akụrụngwa ATMISP na-achịkwa ISP algọridim, nke na-arụ ọrụ na PC. Ndị anọ JTAG Ọdụ ụgbọ mmiri LPT na-emepụta akara, ma eriri nbudata ISP na-echekwa ha tupu ịbanye na ngwaọrụ ATF15xx na bọọdụ Mmepe/Programmer CPLD. Ihe 10-pin JTAG E gosipụtara pinout isi Port na bọọdụ Mmepe/Programmer CPLD na eserese 8, yana akụkụ nke nwoke J 10-pin a.TAG nkụnye eji isi mee ka egosiri na foto 9.
Ọgụgụ 8. 10-pin JTAG Isi Port Pinout
- Ihe 10-pin JTAG Port Header pinout dakọtara na eriri ọdụ ụgbọ mmiri ATDH1150PC/VPC na eriri USB ATDH1150USB, yana Altera.
- ByteBlaster/MV/II eriri dabeere n'ọdụ ụgbọ mmiri. Na mgbakwunye, ngwa ATMISP v6.7 na-enye ohere iji ma Atmel
- ATDH1150PC/VPC/USB cable ma ọ bụ eriri ByteBlaster/MV/II iji mejuputa ISP.
- ATMISP v7.0 na-akwado naanị eriri ATDH1150USB.
- bọọdụ nkwụnye nkwụnye
- ATF15xx-DK3 CPLD Development/Programmer Socket Adapter Boards (ATF15xx-DK3-XXXX) bụ bọọdụ sekit nwere njikọ na ATF15xx-DK3 CPLD Development/Programmer Board. A na-eji ha na njikọ ATF15xx-DK3 CPLD Development/Programmer Board iji nyochaa ma ọ bụ mmemme ATF15xx ISP CPLD ngwaọrụ n'ụdị ngwugwu dị iche iche. Enwere bọọdụ nkwụnye nkwụnye anọ dị maka ATF15xx-DK3 na-ekpuchi 44-TQFP, 44-PLCC, 84-PLCC, na 100-
- Ụdị ngwugwu TQFP na ezinụlọ ATF15xx nke CPLDs.
- bọọdụ nkwụnye nkwụnye ọ bụla nwere oghere maka ngwaọrụ ATF15xx ma nwee nkụnye eji isi mee nwoke n'akụkụ ala, nke akpọrọ JP1 na JP2. Ndị nkụnye eji isi mee n'akụkụ ala na ndị isi nwanyị na bọọdụ ATF15xx-DK3, akpọrọ JP4 na JP3. Ngosipụta akụkụ anọ nke 7, mgbanaka bọtịnụ,
- JTAG akara ọdụ ụgbọ mmiri, oscillator, VCCINT, VCCIO, na GND na CPLD Development/Programmer Board jikọtara ya na ngwaọrụ ATF15xx dị na Socket Adapter Board site na njikọ abụọ a.
- N'elu ihe nkwụnye nkwụnye 44-TQFP, enwere njikọ 10-pin anọ nwere otu akụkụ dịka J.TAG Njikọ ISP. Ejikọrọ ntụtụ nke njikọ anọ ndị a na ntinye na ntụtụ I/O (belụsọ anọ JTAG atụdo) nke ebumnuche CPLD ngwaọrụ. Enwere ike iji ha jikọọ na oscilloscope ma ọ bụ onye nyocha mgbagha iji weghara ọrụ ntinye yana ntụtụ I/O nke CPLD. Enwere ike iji ha jikọọ ntinye na ntụtụ I/O nke CPLD na bọọdụ mpụga ma ọ bụ ngwaọrụ ndị ọzọ maka nleba anya ma ọ bụ nyocha ọkwa sistemụ.
- Cable nbudata nke Atmel ATF15xx ISP
- The ATF15xx ISP Download Cable (P/N: ATDH1150VPC) jikọọ ọdụ ụgbọ mmiri LPT nke PC na 10-pin J.TAG nkụnye eji isi mee na CPLD Development/Programmer Board ma ọ bụ bọọdụ sekit omenala. Egosiri nke a na eserese 10. Igwe ISP a na-arụ ọrụ dị ka ihe nchekwa iji chekwaa JTAG akara n'etiti ọdụ ụgbọ mmiri LPT PC na ATF15xx na bọọdụ sekit. Igwe ọkụ ọkụ ọkụ dị n'azụ ụlọ njikọ nwoke 25-pin na-egosi na ejikọrọ eriri ahụ nke ọma.
- Jide n'aka na agbanyere ọkụ ọkụ a tupu iji Atmel CPLD ISP Software (ATMISP).
- Igwe ISP a nwere njikọ nwoke 25-pin (DB25), nke ejikọrọ na ọdụ ụgbọ mmiri LPT nke PC. Ngwongwo nwanyị 10-pin na-ejikọta na nwoke 10-pin JTAG nkụnye eji isi mee na bọọdụ sekit ISP. Ụkwụ na-acha uhie uhie na eriri rịbọn na-egosi nghazi nke pin 1 nke nkwụnye nwanyị. Nwoke 10-pin JTAG Isi okwu na CPLD
- Board Development/Programmer bụ polarized iji gbochie ndị ọrụ ịtinye plọg ụmụ nwanyị na nghazi na-ezighi ezi.
- Ngwa mmepe/Programmer CPLD gụnyere ATF15xx ISP Download Cable
(ATDH1150VPC); Agbanyeghị, enwere ike iji eriri ISP ndị ọzọ akwadoro. Enwere ike iji eriri ATDH1150VPC, ATDH1150USB, ByteBlasterMV, na ByteBlasterII maka ngwaọrụ ATF15xx/ASL (5V) na ATF15xxASV/ASVL (3.3V), ebe ATDH1150PC ochie na ByteBlaster15 ATF/SLAS nwere ike iji ya naanị.
- Ọgụgụ 11 na-egosi pinout isi isi nwanyị 10 maka ATF15xx ISP Download Cable. Isi mkpịsị isi nwoke 10-pin dị na bọọdụ PC (ọ bụrụ na ejiri ya maka ISP) ga-adakọrịrị na pinout a.
- Mara: bọọdụ sekit ga-ebunye VCC na GND na eriri CPLD ISP site na isi isi nwoke nwere pin iri.
Eserese atụmatụ
Ntụaka na nkwado
Maka ntụnye aka na nkwado ngwanrọ PLD ndị ọzọ, akwụkwọ dịka enyemaka files, nkuzi, ndetu ngwa/nkenke, na ntuziaka onye ọrụ dị na www.atmel.com.
Ngwa ngwa Atmel ProChip Designer
Isiokwu 8.ProChip Ntụaka na Nkwado
| Onye nrụpụta ProChip | Site na isi menu ProChip… |
| Enyemaka | Họrọ Enyemaka > Enyemaka Onye nrụpụta Prochip. |
| Nkuzi | Họrọ Enyemaka > Nkuzi. |
| Nsogbu na ngwọta mara | Họrọ Enyemaka > Review KPS. |
Ngwa ngwa Atmel WinCUPL
Isiokwu 9. Ntuziaka na nkwado WinCUPL
| WinCUPL | Site na isi menu WinCUPL… |
| Enyemaka | Họrọ Enyemaka > ọdịnaya. |
| Ntuziaka ntụaka ndị mmemme CUPL | Họrọ Enyemaka > Ntuziaka CUPL Programmers. |
| Nkuzi | Họrọ Enyemaka > Ozi Atmel > nkuzi1.pdf. |
| Nsogbu na ngwọta mara | Họrọ Enyemaka > Ozi Atmel > CUPL_BUG.pdf. |
Ngwa Atmel ATMISP
Tebụl 10. Ntuziaka na nkwado ATMISP
| ATMISP | Site na isi mpio ATMISP menu… |
| Enyemaka Files | Họrọ Enyemaka > Enyemaka ISP. |
| Nkuzi | Họrọ Enyemaka > Nkuzi ATMISP. |
| Nsogbu na ngwọta mara | Iji ihe nchọgharị Windows Explorer, chọta ebe nchekwa ATMISP wee mepee ya gụọ.txt file ya na onye editọ ederede ASCII. |
Ngwa Ntụgharị Atmel POF2JED
Isiokwu 11. Ntuziaka na nkwado POF2JED
| POF2JED | Site na isi menu POF2JED… |
| Mpempe akwụkwọ ntụgharị ATF15xx | Họrọ Enyemaka > Nhọrọ ntụgharị. |
Nkwado ndị teknuzu
- Maka nkwado teknụzụ na okwu metụtara Atmel PLD, kpọtụrụ Atmel PLD Application Group na:
- Email pld@atmel.com
- Igwe ọkụ (+1)408-436-4333
- Ụdị Nkwado Ọnlaịnụ http://support.atmel.com/bin/customer.exe
Akụkọ ngbanwe
| Ndozigharị | Ụbọchị | Nkọwa |
| 3605C | 06/2014 | Melite schematics, ndebiri, akara ngosi na ibe nkwuputa. Tinye ngalaba akụkọ ndegharị. |
| 3605B | 05/2008 |
- Ụlọ ọrụ Atmel 1600 Technology Drive, San Jose, CA 95110 USA T: (+1) (408) 441.0311 F: (+1) (408) 436.4200 | www.atmel.com
- © 2014 Atmel Corporation. / Mkpu.: Atmel-3605C-CPLD-ATF15xx-DK3-mmepe-Kit-UserGuide_062014.
- Atmel®, Atmel logo na ngwakọta ya, na-enyere ohere na-akparaghị ókè, na ndị ọzọ bụ ụghalaahịa ma ọ bụ ụghalaahịa edenyere n'akwụkwọ ikikere nke Ụlọ ọrụ Atmel na US na
obodo ndị ọzọ. Usoro ndị ọzọ na aha ngwaahịa nwere ike ịbụ ụghalaahịa nke ndị ọzọ. - NKWUKWU: Enyere ozi dị n'akwụkwọ a n'ihe metụtara ngwaahịa Atmel. Enweghị ikike, nke egosipụtara ma ọ bụ nke egosipụtara, site na estoppel ma ọ bụ n'ụzọ ọzọ, enyere ikike ikike ọgụgụ isi site na akwụkwọ a ma ọ bụ n'ihe metụtara ire ngwaahịa Atmel.
- Ewezuga DỊ KA E EKWESỊRỊ N'ỤRỤ ATMEL NA ỌNỌDỤ NKE ỊERE N'ỤRỤ ATMEL. WEBSaịtị, ATMEL na-eche na ọ nweghị ụgwọ ọ bụla ma na-ekwupụta nkwupụta, akọwapụtara, ma ọ bụ ikike iwu metụtara ngwa ahịa ya gụnyere, mana ọnweghị oke na, ikike akwadoro nke achụmnta ego nwere ike ime, ENWEGHỊ MMAPỤTA. N'ime
- Ọ BỤGHỊ ihe omume ATMEL ga-akwụ ụgwọ maka ihe ọ bụla kpọmkwem, nke na-ezighi ezi, nke na-esi na ya pụta, ntaramahụhụ, nke pụrụ iche, ma ọ bụ nke na-emebu ihe (gụnyere, na-enweghị oke, mmebi nke mfu na uru, mmekpa ahụ nke azụmahịa) Enweghị ike iji akwụkwọ a, ọbụlagodi na ATMEL KWESỊRỊ NTỤRỤ MGBE IKE MMIRI dị otú ahụ.
- Atmel anaghị eme ihe nnọchi anya ma ọ bụ akwụkwọ ikike gbasara izi ezi ma ọ bụ izu oke nke ọdịnaya nke a
akwụkwọ ma chekwaa ikike ime mgbanwe na nkọwapụta na nkọwa ngwaahịa n'oge ọ bụla na-enweghị ọkwa. Atmel anaghị ekwe nkwa imelite ozi dị n'ime ya. Ọ gwụla ma enyereghị ya nke ọma, ngwaahịa Atmel adabaghị, na agaghị eji ya, ngwa ụgbọ ala. Ebubeghị ngwaahịa Atmel, ikike, ma ọ bụ kwadoro maka ojiji dị ka akụrụngwa na ngwa ezubere iji kwado ma ọ bụ kwado ndụ. - Nchekwa-dị oke egwu, ndị agha, na ngwa ngwa ngwa nkwuputa: Emebere ngwaahịa Atmel maka na agaghị eji ya mee ihe n'ihe metụtara ngwa ọ bụla ebe ọdịda nke ngwaahịa ndị a ga-atụ anya na ọ ga-ebute mmerụ ahụ ma ọ bụ ọnwụ dị ukwuu nke onwe ("Ngwa Nchekwa-Critical") na-enweghị ederede kpọmkwem nke onye ọrụ Atmel.
- nkwenye. Ngwa nchekwa-dị oke mkpa gụnyere, na-enweghị oke, ngwaọrụ nkwado ndụ, yana sistemu, akụrụngwa ma ọ bụ sistemu maka ịrụ ọrụ nke akụrụngwa nuklia na sistemu ngwa ọgụ.
- Emebeghị ngwaahịa Atmel ma ọ bụ bu n'obi maka ojiji na ngwa agha ma ọ bụ ikuku ikuku ma ọ bụ gburugburu ma ọ bụrụ na Atmel họpụtara kpọmkwem ka ọ bụrụ ọkwa agha. Emebeghị ngwaahịa Atmel ma ọ bụ bu n'obi maka ojiji na ngwa ụgbọ ala ma ọ bụrụ na Atmel họpụtara ya ka ọ bụrụ ọkwa ụgbọ ala.
- E si na: Arrow.com.
Akwụkwọ / akụrụngwa
 |
Atmel ATF15xx-DK3 CPLD Mmepe/ Ngwa ihe mmemme [pdf] Ntuziaka onye ọrụ ATF15xx-DK3 CPLD Development Programmer Kit, ATF15xx-DK3, CPLD Development Programmer Kit, ngwa mmemme mmemme, ngwa mmemme |
