Atmel ATF15xx-DK3 CPLD Development/Programmer Kit
Nhanganyaya
Iyo Atmel® ATF15xx-DK3 Complex Programmable Logic Device (CPLD) Development/Programmer Kit igadziriro yakakwana yekuvandudza uye In-System Programming (ISP) programmer yeAtmel ATF15xx Mhuri yeindasitiri yakajairika pini inoenderana neCPLDs ine Logic Doubling® maficha. Iyi kit inopa vagadziri nzira inokurumidza uye iri nyore yekugadzira prototypes uye kuongorora magadzirirwo matsva neATF15xx ISP CPLD. Iyo ATF15xx Mhuri yeISP CPLDs inosanganisira iyo Atmel ATF15xxAS, ATF15xxASL, ATF15xxASV, uye ATF15xxASVL CPLDs. Nekuwanikwa kweakasiyana socket adapter board kutsigira mazhinji epasuru mhando (1) inopihwa muATF15xx Mhuri yeISP CPLDs, kit iyi inogona kushandiswa seISP programmer kuronga maATF15xx ISP CPLDs mune akawanda emhando dzepakeji dziripo. (1) kuburikidza neindasitiri chiyero JTAG interface (IEEE 1149.1).
Kit Zviri mukati
- Atmel CPLD Development/Programmer Board (P/N: ATF15xx-DK3)
- Atmel 44-pini TQFP Socket Adapter Board (P/N: ATF15xx-DK3-SAA44)(2)
- Atmel ATF15xx LPT-yakavakirwa JTAG ISP Dhaunirodha Cable (P/N: ATDH1150VPC)
- maviri Atmel 44-pini TQFP Sample Devices
Device Support
Iyo ATF15xx-DK3 CPLD Development/Programmer Kit inotsigira zvinotevera zvishandiso mune ese aripo parizvino Atmel kumhanya mamakisi uye mapakeji (kunze kwe100-PQFP):
- ATF1502AS/ASL
- ATF1504AS/ASL
- ATF1508ASV/ASVL
- ATF1502ASV
- ATF1504ASV/ASVL
- ATF1508AS/ASL
- Iyo socket adapter board haina kupihwa iyo 100-pini PQFP.
- Iyo chete 44-pini TQFP Socket Adapter Board inosanganisirwa mune iyi kit. Mamwe ma socket adapter board anotengeswa akasiyana. Ona Chikamu, "Hardware Tsanangudzo" kuti uwane rumwe ruzivo nezve socket adapter board macode ekuodha.i
Kit Features
CPLD Development/Programmer Board
- 10-pini JTAG-ISP Port
- Yakadzorwa Magetsi Ekupa Masekete e9VDC Power Source
- Inosarudzwa 5V, 3.3V, 2.5V, kana 1.8VI/O Voltage Kuwedzera
- Inosarudzwa 1.8V, 3.3V, kana 5.0V Core Voltage Kuwedzera
- 44-pini TQFP Socket Adapter Board
- Misoro yeI/O Pini dzeATF15xx Chishandiso
- 2MHz Crystal Oscillator
- Zvina 7-chikamu che LED Chiratidziro
- Eight Individual LEDs
- Eight Push-bhatani Shanduko
- Global Clear uye Output Gonesa Push-bhatani Kuchinja
- Iyezvino Measurement Jumpers
Logic Doubling CPLDs
ATF15xx ISP CPLD ine Logic Doubling Architecture
- ATF15xx ISP Download Cable
- 5V, 3.3V, 2.5V, kana 1.8V ISP Dhaunirodha Cable yePC Parallel Printer (LPT) Port
- PLD Development Software
- Iyo Atmel PLD yekuvandudza software maturusi anowanikwa online kuti PLD mugadziri ashandise iyo ATF15xx ISP CPLDs. Ndokumbira utarise iyo Overview gwaro, "PLD
- Dhizaina Software Pamusoroview” inowanika pa:
- http://www.atmel.com/images/atmel-3629-pld-design-software-overview.pdf
System Zvinodiwa
- Izvo zvishoma hardware uye software inodiwa kuronga ATF15xx ISP CPLD mudziyo wakagadzirwa uchishandisa Atmel ProChip Designer Software paCPLD Development/Programmer Board kuburikidza neAtmel ATMISP v6.x (ATF15xx CPLD ISP Software) ndeiyi:
- x86 Microprocessor-based Computer
- Windows XP®, Windows® 98, Windows NT® 4.0, kana Windows 2000
- 128-MByte RAM
- 500-MByte Yemahara Hard Disk Space
- Windows-inotsigirwa Mouse
- Inowanikwa Parallel Printer (LPT) Port
- 9VDC Power Supply ine 500mA yeSupply Current
- SVGA Monitor (800 x 600 Resolution)
Kuraira Ruzivo
| Atmel Chikamu Nhamba | Tsanangudzo |
| ATF15xx-DK3 | CPLD Development/Programmer Kit (inosanganisira iyo ATF15xxDK3-SAA44*) |
| ATF15xxDK3-SAA100 | 100-pini TQFP Socket Adapter Board yeDK3 Board |
| ATF15xxDK3-SAJ44 | 44-pini PLCC Socket Adapter Board yeDK3 Board |
| ATF15xxDK3-SAJ84 | 84-pini PLCC Socket Adapter Board yeDK3 Board |
| ATF15xxDK3-SAA44* | 44-pini TQFP Socket Adapter Board yeDK3 Board |
Hardware Tsanangudzo
CPLD Development/Programmer Board
- Iyo CPLD Development/Programmer uye Socket Adapter Boards inoratidzwa mumufananidzo uri pazasi ine zvinhu zvinobatsira pakugadzira, prototyping, kana kuongorora.
- ATF15xx CPLD magadzirirwo. Zvimiro zvinoita kuti iyi ive ine hunyanzvi hwekutanga / yekuvandudza kit uye ISP programmer yemhuri yeATF15xx yaJ.TAG-ISP CPLDs dzinosanganisira:
- Push-bhatani Inochinja
- LEDs
- 7-chikamu Maonero
- 2MHz Crystal Oscillator
- 5V, 3.3V, 2.5V, kana 1.8V VCCIO Selector
- 1.8V, 3.3V, kana 5.0V VCCINT Selector
- JTAG ISP Port
- Socket Adapters
- 7-chikamu Inoratidza ine Selectable Jumpers
- Iyo CPLD Development/Programmer Board ine ina 7-segment inoratidza iyo inobvumira kutariswa kweiyo ATF15xx CPLD zvabuda. Aya maratidziro mana akanyorwa kuti DSP1, DSP2, DSP3, uye DSP4. Iwo 7-segment anoratidza ane akajairwa anode LEDs ane akajairika anode mitsara yakabatana neVCCIO (I/O supply vol.tage yeCPLD) kuburikidza nenhevedzano yezvidziviriro zvine zvinokwanisa kusvetuka svetuka zvakanzi JPDSP1, JPDSP2, JPDSP3, uye JPDSP4. Aya majumper anogona kubviswa kuti
dzima zviratidziro nekusunungura VCCIO kune zviratidziro. Mitsetse yekathodhi yega yega yakabatana neI/O pini dzeATF15xx CPLD paCPLD. - Development/Programmer Kit. Kuti ubatidze chimwe chikamu, kusanganisira iyo DOT yechiratidziro, iyo inoenderana neATF15xx I/O pini yakabatana nechikamu ichi che LED inofanira kunge iri mune yakaderera mamiriro ine inoenderana inosarudzwa jumper set; saka, zvinobuda zveATF15xx mudziyo zvinoda kumisikidzwa kune inoshanda-yakaderera zvinobuda mudhizaini. file. Zviratidziro zvinoshanda zvakanyanya pa2.5V VCCIO kana kupfuura.
- Chikamu chimwe nechimwe chechiratidziro chega chega chakaomeswa-waya kune imwe chaiyo I/O pini yeATF15xx mudziyo. Kumapini epamusoro ekuverenga mapini (100-pini uye yakakura), ese manomwe zvikamu uye zvikamu zveDOT zvezviratidziro zvina zvakabatana neI/O pini; zvisinei, kune yakaderera pini kuverenga zvishandiso, chete subset yezviratidziro, yekutanga neyechina kuratidza, yakabatana neiyo ATF15xx mudziyo weI/O pini. Matafura 1 uye 2 anoratidza 7-segment yekuratidzira pasuru yekubatanidza kune ATF15xx mudziyo. Iyo yedunhu schematic yezviratidziro uye jumpers inoratidzwa mumufananidzo uri pazasi.
Mufananidzo 2. Circuit Diagram ye7-segment Display uye Jumpers
Tafura 1.ATF15xx 44-pini Mabatanidza kune 7-segment Displays
| 44-pini TQFP | |||
| DSP/Segment | PLD Pin | DSP/Segment | PLD Pin |
| 1/A | 27 | 3/A | NC |
| 1/B | 33 | 3/B | NC |
| 1/C | 30 | 3/C | NC |
| 1/D | 21 | 3/D | NC |
| 1/E | 18 | 3/E | NC |
| 1 / F | 23 | 3 / F | NC |
| 1 G | 20 | 3 G | NC |
| 1/DOT | 31 | 3/DOT | NC |
| 2/A | NC | 4/A | 3 |
| 2/B | NC | 4/B | 10 |
| 2/C | NC | 4/C | 6 |
| 2/D | NC | 4/D | 43 |
| 2/E | NC | 4/E | 35 |
| 2 / F | NC | 4 / F | 42 |
| 2 G | NC | 4 G | 34 |
| 2/DOT | NC | 4/DOT | 11 |
| 44-pini PLCC | |||
| DSP/Segment | PLD Pin | DSP/Segment | PLD Pin |
| 1/A | 33 | 3/A | NC |
| 1/B | 39 | 3/B | NC |
| 1/C | 36 | 3/C | NC |
| 1/D | 27 | 3/D | NC |
| 1/E | 24 | 3/E | NC |
| 1 / F | 29 | 3 / F | NC |
| 1 G | 26 | 3 G | NC |
| 1/DOT | 37 | 3/DOT | NC |
| 2/A | NC | 4/A | 9 |
| 2/B | NC | 4/B | 16 |
| 2/C | NC | 4/C | 12 |
| 2/D | NC | 4/D | 5 |
| 2/E | NC | 4/E | 41 |
| 2 / F | NC | 4 / F | 4 |
| 2 G | NC | 4 G | 40 |
| 2/DOT | NC | 4/DOT | 17 |
Tafura 2.ATF15xx 84-pini uye 100-pini MaConnections kune 7-segment Displays
| 84-pini PLCC | |||
| DSP/Segment | PLD Pin | DSP/Segment | PLD Pin |
| 1/A | 68 | 3/A | 22 |
| 1/B | 74 | 3/B | 28 |
| 1/C | 70 | 3/C | 25 |
| 1/D | 63 | 3/D | 21 |
| 1/E | 58 | 3/E | 16 |
| 1 / F | 65 | 3 / F | 17 |
| 1 G | 61 | 3 G | 12 |
| 1/DOT | 73 | 3/DOT | 29 |
| 2/A | 52 | 4/A | 5 |
| 2/B | 57 | 4/B | 10 |
| 2/C | 55 | 4/C | 8 |
| 2/D | 48 | 4/D | 79 |
| 2/E | 41 | 4/E | 76 |
| 2 / F | 50 | 4 / F | 77 |
| 2 G | 45 | 4 G | 75 |
| 2/DOT | 50 | 4/DOT | 11 |
| 100-pini TQFP | |||
| DSP/Segment | PLD Pin | DSP/Segment | PLD Pin |
| 1/A | 67 | 3/A | 13 |
| 1/B | 71 | 3/B | 19 |
| 1/C | 69 | 3/C | 16 |
| 1/D | 61 | 3/D | 8 |
| 1/E | 57 | 3/E | 83 |
| 1 / F | 64 | 3 / F | 6 |
| 1 G | 60 | 3 G | 92 |
| 1/DOT | 75 | 3/DOT | 20 |
| 2/A | 52 | 4/A | 100 |
| 2/B | 54 | 4/B | 94 |
| 2/C | 47 | 4/C | 97 |
| 2/D | 41 | 4/D | 81 |
| 2/E | 46 | 4/E | 76 |
| 2 / F | 40 | 4 / F | 80 |
| 2 G | 45 | 4 G | 79 |
| 2/DOT | 56 | 4/DOT | 93 |
Ma LED ane Selectable Jumpers
Iyo CPLD Development/Programmer Board ine masere emunhu maLED, ayo anobvumira vagadziri kuratidza zvinobuda masaini kubva kumushandisi I/Os yeATF15xx zvishandiso. Aya ma LED masere akanyorwa kuti LED1 kune LED8 paCPLD Development/Programmer Board. Iyo cathode ye LED yega yega yakabatana neGround (GND) kuburikidza neyakatevedzana resistor, nepo anode yega yega LED yakabatana nemushandisi I/O pini yeCPLD kuburikidza neJPL1/2/3/4/5/6/7 /8 inosarudzwa jumper. Aya majumper anogona kubviswa kuti avhare maLED nekusunungura anode e LED kune I/O pini dzeCPLD. Mufananidzo uri pasi apa unoratidza dhiyabhorosi yedhiyagiramu ye LED ine sarudzo yekusvetuka.
Kuti ubatidze imwe LED, iyo inoenderana neATF15xx I/O pini yakabatana ne LED inofanirwa kunge iri mune inonzwisisika yakakwira mamiriro ine inoenderana jumper set; saka, izvo zvinobuda zveATF15xx mudziyo zvinozoda kugadziridzwa sezvinoshanda zvakakwirira zvinobuda. Iwo maLED anoshanda zvakanyanya pa2.5V VCCIO kana kupfuura.
Iyo yepasi pini kuverenga zvishandiso (44-pini) inongova ina maI/Os akabatana neLED1/2/3/4. Kune epamusoro pini-kuverenga zvishandiso (100-pini uye yakakura), ese masere maLED akabatana neI/Os yemuchina. Tafura 3 inoratidza akasiyana mapakeji ekubatanidza eCPLD I/Os kune maLEDs.
Tafura 3.ATF15xx Kubatanidza kune LEDs
| 44-pini TQFP | |
| LED | PLD Pin |
| LED1 | 28 |
| LED2 | 25 |
| LED3 | 22 |
| LED4 | 19 |
| 44-pini PLCC | |
| LED | PLD Pin |
| LED1 | 34 |
| LED2 | 31 |
| LED3 | 28 |
| LED4 | 25 |
| 84-pini PLCC | |
| LED | PLD Pin |
| LED1 | 69 |
| LED2 | 67 |
| LED3 | 64 |
| LED4 | 60 |
| LED5 | 27 |
| LED6 | 24 |
| LED7 | 18 |
| LED8 | 15 |
| 100-pini TQFP | |
| LED | PLD Pin |
| LED1 | 68 |
| LED2 | 65 |
| LED3 | 63 |
| LED4 | 58 |
| LED5 | 17 |
| LED6 | 14 |
| LED7 | 10 |
| LED8 | 9 |
Push-bhatani Swichi neSelectable Jumpers yeI/O Pini
- Iyo CPLD Development/Programmer Board ine masere ekusundidzira-bhatani switch, ayo akabatana neI/O mapini eCPLD. Maswichi anotumira masiginecha ekupinza kune mushandisi I/O mapini eiyo ATF15xx mudziyo. Maswichi aya akanyorwa kuti SW1 kuenda kuSW8 paCPLD Development/Programmer
Board. Imwe magumo ega ega ekuisa push-bhatani switch yakabatana neVCCIO, nepo imwe magumo ega ega push-bhatani switch yakabatana kune yekudhonza-pasi resistor uye yobva yabatanidzwa kune chaiyo I/O pini yeCPLD kuburikidza neJPS1/2. /3/4/5/6/7/8 jumper inosarudzwa. - Kana chero imwe yeiyi switch yakatsikirirwa uye jumper inoenderana yaiswa, iyo chaiyo I/O pini yechishandiso inofambiswa kune ine logic yakakwirira mamiriro nekubuda kwe switch yedunhu. Sezvo yega yega-push-bhatani switch yakabatana zvakare kune yekudhonza-pasi resistor, iyo yekuisa ichave ine logic yakaderera mamiriro kana switch isina kudzvanywa neinowirirana jumper set. Kana iyo push-bhatani jumper isina kuiswa, pini inoenderana ichabatwa sepini isina kubatana. Mufananidzo 4 idhizaini yedunhu repush-bhatani switch uye inosarudzwa jumper. Tafura 4 inoratidza kubatanidzwa kweaya masere push-bhatani switch kune CPLD I/O mapini mumhando dzakasiyana dzepakeji.
Tafura 4.ATF15xx Kubatanidza kune I / O Pin Switches
| 44-pini TQFP | |
| Push Bhatani | PLD Pin |
| SW1 | 15 |
| SW2 | 14 |
| SW3 | 13 |
| SW4 | 12 |
| SW5 | 8 |
| SW6 | 5 |
| SW7 | 2 |
| SW8 | 44 |
| 44-pini PLCC | |
| Push Bhatani | PLD Pin |
| SW1 | 21 |
| SW2 | 20 |
| SW3 | 19 |
| SW4 | 18 |
| SW5 | 14 |
| SW6 | 11 |
| SW7 | 8 |
| SW8 | 6 |
| 84-pini PLCC | |
| Push Bhatani | PLD Pin |
| SW1 | 54 |
| SW2 | 51 |
| SW3 | 49 |
| SW4 | 44 |
| SW5 | 9 |
| SW6 | 6 |
| SW7 | 4 |
| SW8 | 80 |
| 100-pini TQFP | |
| Push Bhatani | PLD Pin |
| SW1 | 48 |
| SW2 | 36 |
| SW3 | 44 |
| SW4 | 37 |
| SW5 | 96 |
| SW6 | 98 |
| SW7 | 84 |
| SW8 | 99 |
Push-bhatani Swichi neSelectable Jumpers yeGCLR uye OE1 Pini
Iyo CPLD Development/Programmer Board ine maviri ekusundidzira-bhatani switch eiyo Global Clear (GCLR) uye Output Enable (OE1) mapini eCPLD. Iwo maswichi anodzora logic states yeOE1 neGCLR mapipu emidziyo yeATF15xx. Aya ma switch akanyorwa SW-GCLR uye SW-GOE1 pabhodhi. Imwe magumo eSW-GCLR yekuisa push-bhatani switch yakabatana neGND. Imwe magumo e
iyo push-bhatani switch yakabatana kune yekudhonza-up resistor kuVCCIO uye yobva yabatana neGCLR yakatsaurirwa pini yekupinza yeATF15xx mudziyo. Inoitirwa kushandiswa senge inoshingaira-yakaderera reset chiratidzo kuseta zvakare marejista muATF15xx mudziyo une JPGCLR inosarudzwa jumper set. Saizvozvo, imwe magumo eSW-GOE1 yekuisa push-bhatani switch yakabatana neGND. Imwe mugumo wepush-bhatani switch
yakabatana nekudhonza-kumusoro resistor kuVCCIO uye yobva yabatana neOE1 yakatsaurirwa pini yekupinza yeATF15xx mudziyo. Iyo inoitirwa kushandiswa seyakagwinya-yakaderera inoburitsa inogonesa chiratidzo chekudzora kugonesa / kuremara kweyetatu-nyika inobuda mabuffers muATF15xx neJPGOE inosarudzwa jumper set. Mufananidzo 5 ndiyo dhiyagiramu yedunhu repush-bhatani switch uye jumpers yeGCLR uye OE1 pini.
Kana chero ipi yeaya ma-push-bhatani switch akatsikirirwa uye jumper inoenderana yaiswa, iyo chaiyo I/O yeCPLD inofambiswa kune logic yakaderera mamiriro. Sezvo yega yega-push-bhatani yakabatanidzwawo kune yekudhonza-up resistor, iyo inoenderana CPLD yekuisa ichave ine logic yakakwirira mamiriro kana push-bhatani switch isina kudzvinyirirwa pamwe inoenderana inosarudzwa jumper set. Kana iyo inosarudzwa jumper isina kusetwa, inoenderana yakatsaurirwa pini yekuisa yeCPLD inogona kutorwa seNo Connect (NC) pini. Tafura 5 inoratidza nhamba dzepini dzeGCLR uye OE1 yakatsaurirwa mapini ekuisa emidziyo yeATF15xx mumhando dzese dziripo dzepasuru.
Mufananidzo 5. Circuit Diagram yePush-button Switches uye Selectable Jumpers yeGCLR uye OE1
Tafura 5.Pin Nhamba dzeGCLR neOE1
| 44-pini TQFP | 44-pini PLCC | 84-pini PLCC | 100-pini TQFP | |
| GCLR | 39 | 1 | 1 | 89 |
| OE1 | 38 | 44 | 84 | 88 |
2MHz Oscillator uye Clock Sarudzo Jumper
Iyo Clock Selection Jumper yakanyorwa kuti JP-GCLK paCPLD Development/Programmer Board is two-position jumper iyo inobvumira vashandisi kusarudza iyo GCLK yakatsaurirwa pini yekupinza (ingave GCLK1 kana GCLK2) yeATF15xx mudziyo unofanirwa kubatanidzwa kune inobuda 2MHz oscillator. Mukuwedzera, iyo jumper inogona kubviswa kuti ibvumire yekunze wachi sosi kuti ibatanidzwe neGCLK1 uye/kana GCLK2 yeATF15xx mudziyo. Mufananidzo 6 mufananidzo wedhiyagiramu yedunhu re oscillator uye kusarudzwa jumper. Tafura 6 inoratidza nhamba dzepini dzeGCLK1 uye GCLK2 yakatsaurirwa mapini ekuisa eiyo ATF15xx mudziyo mune ese akasiyana anowanikwa mapakeji marudzi.
Kana iyo GCLK1 jumper yakaiswa, iyo jumper ichave iri kudivi rebhodhi. Kune rimwe divi, kana iyo GCLK2 jumper yakaiswa, iyo jumper ichave iri pakati pebhodhi.
Tafura 6.Pin Nhamba dzeGCLK1 uye GCLK2
| 44-pini TQFP | 44-pini PLCC | 84-pini PLCC | 100-pini TQFP | |
| GCLK1 | 37 | 43 | 83 | 87 |
| GCLK2 | 40 | 2 | 2 | 90 |
VCCIO uye VCCINT Voltage Selection Jumpers uye LEDs
- Iyo VCCIO uye VCCINT Voltage Selection Jumpers, yakanyorwa VCCIO Selector uye VCCINT Selector zvakateerana paATF15xx-DK3 Development/Programming Kit, bvumira kusarudzwa kweiyo I/O
- voltage level (VCCIO) uye core supply voltage nhanho (VCCINT) iyo inoshandiswa kune inotarirwa CPLD pakiti. Kana aya majumper akaiswa nemazvo, ma LED (akanyorwa VCCINT LED uye VCCIO LED) anobatidza; zvisinei, pa low supply voltage mazinga (kureva 2.5V kana pasi), iwo maLED anogona kunge asina kujeka.
- Kune ATF15xxAS/ASL (5.0V) CPLDs, ese VCCIO Selector uye VCCINT Selector jumpers anofanirwa kusetwa ku5.0V.
- Kune ATF15xxASV/ASVL (3.3V) CPLDs, ese VCCIO Selector uye VCCINT Selector Jumpers anofanirwa kusetwa ku3.3V chete.
- Simba reCPLD Development/Programmer Kit rinofanira kudzimwa kana uchichinja chinzvimbo cheVCCIO kana VCCINT Vol.tage Selection Jumper (VCCIO Selector kana VCCINT Selector).
- ICCIO uye ICCINT Jumpers
- Iyo ICCIO uye ICCINT jumpers inogona kubviswa uye kushandiswa seICC kuyerwa mapoinzi. Kana majumper abviswa, mamita emazuva ano anogona kubatanidzwa kune zvitubu kuyera kushandiswa kwemazuva ano kwechinangwa cheCPLD. Kana vashandisi vasingashandisi aya majumper kuyera ikozvino, aya majuru anofanira kuiswa kuitira kuti kiti uye CPLD ishande.
- Voltage Regulators
- Two voltage regulators, akanyorwa VR1 uye VR2, anoshandiswa kuzvimiririra kugadzira uye kugadzirisa iyo
- VCCINT uye VCCIO voltages kubva ku9VDC magetsi. Kuti uwane rumwe ruzivo, ndapota ona iyo ATF15xx-DK3 kit schematic, Mufananidzo 12.
- Power Supply Switch uye Simba LED
- Iyo Power Supply Switch, yakanyorwa kuti POWER SWITCH, inogona kuchinjirwa kune yekubatidza kana kudzima chinzvimbo, iyo inoshandiswa kubatidza kana kudzima simba reiyo ATF15xx-DK3 bhodhi zvichiteerana. Inobvumira iyo 9VDC voltage paPower Supply Jack kuti apfuure kune voltage regulators kana iri panzvimbo. Kana iyo Power Supply Switch ikabatidzwa, iyo Power LED (yakanyorwa POWER LED) inovheneka kuratidza kuti ATF15xx-DK3 Kit inopihwa simba.
- Power Supply Jack uye Power Supply Header
- Iyo ATF15xx-DK3 bhodhi ine marudzi maviri akasiyana emagetsi ekubatanidza akanyorwa JPower uye JP Simba. Chero imwe yeaya magetsi ekubatanidza magetsi anogona kushandiswa kubatanidza 9VDC magetsi sosi kune kit. Yekutanga magetsi yekubatanidza yakanyorwa kuti JPower, idhiramu remagetsi jack ine 2.1mm dhayamita positi, uye inobatana ne2.1mm (yemukati dhayamita) x 5.5mm (yekunze dhayamita) plug yevakadzi. Yechipiri magetsi ekupa musoro wakanyorwa kuti JP Simba, ndeye 4-pini yechirume 0.100 ″ musoro une 0.025 ″ masikweya masheya. Kuvepo kweaya marudzi maviri emagetsi ekubatanidza anobvumira vashandisi kusarudza rudzi rwemagetsi ekushandisa ekushandisa kuATF15xx-DK3 Development/Programmer Kit.
- Imwe chete yeaya maviri magetsi ekubatanidza magetsi anofanirwa kuvezwa ne9VDC sosi asi kwete ese ari maviri panguva imwe chete.
- JTAG ISP Connector uye TDO Selection Jumper
- Iye JTAG ISP Connector yakanyorwa kuti JTAG-IN, inoshandiswa kubatanidza iyo ATF15xx JTAG mapini echiteshi (TCK, TDI, TMS, uye TDO) kuburikidza neISP yekurodha tambo kuenda kune parallel printer (LPT) port yePC yeJ.TAG ISP chirongwa cheATF15xx mudziyo. Polarized connectors anoshandiswa paATF15xx-DK3 uye ISP Download Cable kuderedza matambudziko ekubatanidza. Iyo PIN1 label pazasi peJTAG ISP connector inoratidza pini 1 chinzvimbo chemusoro wepini gumi uyezve inoderedza mukana wekubatanidza ISP Dhawunirodha Cable zvisizvo.
- Kuruboshwe kweJTAG-IN chinongedzo, kune makoramu maviri evias, uye akanyorwa kuti JTAG-OUT. Izvo zvakagadzirirwa kubvumira vashandisi kugadzira JTAG daisy cheni kuita JTAG kushanda kune akawanda madivayiri. Vashandisi vanozoda kutengesa mhando imwechete yekubatanidza neiyo inoshandiswa kuJTAG- IN mune JTAG-OUT chinzvimbo kuti ushandise ichi chiripo chimiro.
- Kugadzira JTAG daisy cheni uchishandisa akawanda ATF15xx-DK3 mabhodhi, iyo TDO Selection Jumper, yakanyorwa JP-TDO, inofanira kuiswa panzvimbo yakakodzera. Kune ese maturusi ari mu daisy cheni kunze kweyekupedzisira mudziyo, jumper iyi inofanirwa kusetwa kune TO NEXT DEVICE chinzvimbo. Pamudziyo wekupedzisira mucheni, jumper iyi inofanirwa kuiswa kune TO ISP CABLE chinzvimbo. Kana jumper iyi iri mu TO NEXT DEVICE chinzvimbo, iyo TDO yeiyo chaiyo JTAG mudziyo uchabatanidzwa kune TDI yeinotevera
- JTAG mudziyo mucheni. Kana iyi jumper iri mu TO ISP CABLE chinzvimbo, iyo TDO yechishandiso ichocho ichabatanidzwa neTDO yeJ.TAG 10-pini yekubatanidza, iyo inobvumira iyo TDO chiratidzo cheiyo mudziyo mucheni kuti ifambiswe ichidzoserwa kuPC inotambira neISP software. Mufananidzo uri pasi apa dhiyagiramu yedunhu re
- JTAG zvibatanidza uye JP-TDO jumper. Tafura iri pazasi inoronga nhamba dzepini dzevana JTAG mapini eiyo ATF15xx mudziyo mumapakeji ese aripo.
Kune imwe chete yekuseta mudziyo, chinzvimbo cheJP-TDO jumper chinofanira kusetwa ku TO ISP CABLE.
Mufananidzo 7. Digiramu yedunhu reJTAG ISP Connectors uye TDO Jumper
- Tafura 7.Pini Nhamba dzaJTAG Port Signals
| 44-pini TQFP | 44-pini PLCC | 84-pini PLCC | 100-pini TQFP | |
| TDI | 1 | 7 | 14 | 4 |
| TDO | 32 | 38 | 71 | 73 |
| TMS | 7 | 13 | 23 | 15 |
| TCK | 26 | 32 | 62 | 62 |
Iyo ISP algorithm inodzorwa neATMISP software, iri kushanda paPC. Ivo vana JTAG masaini anogadzirwa neLPT chiteshi, uye anovharirwa neISP yekurodha tambo isati yapinda muATF15xx mudziyo paCPLD Development/Programmer board. Iyo 10-pini JTAG Port Header pinout pane CPLD Development/Programmer board inoratidzwa muMufananidzo 8, uye zviyero zveiyi gumi-pini murume J.TAG musoro unoratidzwa mufananidzo 9.
Mufananidzo 8. 10-pini JTAG Port Header Pinout
- Iyo 10-pini JTAG Port Header pinout inowirirana neATDH1150PC/VPC LPT port-based cable uye ATDH1150USB USB port based cable, pamwe neAltera.
- ByteBlaster/MV/II LPT chiteshi chakavakirwa tambo. Mukuwedzera, iyo ATMISP v6.7 software inobvumira kushandiswa kweiyo Atmel
- ATDH1150PC/VPC/USB tambo kana iyo ByteBlaster/MV/II tambo yekushandisa ISP.
- ATMISP v7.0 inotsigira tambo yeATDH1150USB chete.
- Socket Adapter Board
- Iyo ATF15xx-DK3 CPLD Development/Programmer Socket Adapter Boards (ATF15xx-DK3-XXXXX) mabhodhi edunhu anodyidzana neATF15xx-DK3 CPLD Development/Programmer Board. Iwo anoshandiswa pamwe chete neATF15xx-DK3 CPLD Development/Programmer Board kuongorora kana kuronga ATF15xx ISP CPLD zvishandiso mumhando dzakasiyana dzepakeji. Kune mana Socket Adapter Boards iripo yeATF15xx-DK3 inovhara iyo 44-TQFP, 44-PLCC, 84-PLCC, uye zana-
- TQFP mapakeji marudzi mumhuri yeATF15xx yeCPLDs.
- Imwe neimwe socket adapter board ine socket yeATF15xx mudziyo uye ine misoro yechirume padivi rezasi, yakanyorwa JP1 uye JP2. Misoro iri pazasi side mate ine misoro yechikadzi paATF15xx-DK3 board, yakanyorwa JP4 uye JP3. Iwo mana 7-chikamu anoratidza, push-bhatani switch,
- JTAG masaini echiteshi, oscillator, VCCINT, VCCIO, uye GND paCPLD Development/Programmer Board zvakabatana neATF15xx mudziyo paSocket Adapter Board kuburikidza neaya maseti maviri ezvekubatanidza.
- Pamusoro peiyo 44-TQFP socket adapter, pane ina 10-pini yekubatanidza ine zviyero zvakafanana neJ.TAG ISP connector. Mapini eaya mana anobatanidza akabatana kune yekupinza uye I/O pini (kunze kweina JTAG pini) yechinangwa cheCPLD mudziyo. Inogona kushandiswa kubatanidza kune oscilloscope kana logic analyzer kutora zviitiko zvekupinza uye I/O mapini eCPLD. Iwo zvakare anogona kushandiswa kubatanidza iyo yekupinza uye I/O mapini eCPLD kune mamwe ekunze mabhodhi kana zvishandiso zvehurongwa hwekuongorora kana kuyedza.
- Atmel ATF15xx ISP Download Cable
- Iyo ATF15xx ISP Yekurodha Cable (P/N: ATDH1150VPC) inobatanidza LPT chiteshi chePC kune gumi-pini J.TAG musoro paCPLD Development/Programmer Board kana tsika yedunhu bhodhi. Izvi zvinoratidzwa mumufananidzo 10. Iyi ISP cable inoshanda sebuffer kuvharira JTAG masaini pakati pePC's LPT port uye iyo ATF15xx pabhodhi redunhu. Iyo Power-On LED kuseri kwe25-pini yechirume yekubatanidza imba inoratidza kuti tambo yakabatana nemazvo.
- Ita shuwa kuti LED iyi yakavhurwa usati washandisa Atmel CPLD ISP Software (ATMISP).
- Iyi ISP tambo ine 25-pini (DB25) yechirume yekubatanidza, iyo yakabatana neLPT port yePC. Iyo 10-pini yechikadzi plug inobatanidza kune gumi-pini murume JTAG musoro pane ISP wedunhu bhodhi. Mutsetse mutsvuku uri patambo yeribhoni unoratidza kutaridzika kwepini 1 yeplug yechikadzi. Iyo 10-pini murume JTAG musoro paCPLD
- Budiriro/Purogiramu Bhodhi inoiswa polarized kudzivirira vashandisi kubva kuisa iyo plug yevakadzi munzira isiriyo.
- Iyo CPLD Development/Programmer kits inosanganisira iyo ATF15xx ISP Yekurodha Cable
(ATDH1150VPC); zvisinei, mamwe anotsigirwa ISP netambo anogonawo kushandiswa. Iyo ATDH1150VPC, ATDH1150USB, ByteBlasterMV, uye ByteBlasterII tambo dzinogona kushandiswa kuATF15xx/ASL (5V) uye ATF15xxASV/ASVL (3.3V) zvishandiso, nepo ATDH1150PC netambo dzeByteBlaster dzichigona kushandiswa (15x) chete.
- Mufananidzo 11 unoratidza 10-pini yemusoro wemukadzi piniout yeATF15xx ISP Dhawunirodha Cable. Iyo 10-pini yechirume musoro pinout paPC board (kana yakashandiswa ISP) inofanira kuenderana nepiniti iyi.
- Cherechedza: Bhodhi redunhu rinofanira kupa VCC neGND kuCPLD ISP Cable kuburikidza negumi-pini musoro wechirume.
Schematic Diagrams
References uye Tsigiro
Kuti uwane mamwe PLD dhizaini software mareferensi uye rutsigiro, zvinyorwa zvakaita serubatsiro files, tutorials, zvinyorwa zvekushandisa / pfupiso, uye madhairekitori evashandisi anowanikwa pa www.atmel.com.
Atmel ProChip Mugadziri Software
Tafura 8.ProChip Designer References uye Tsigiro
| ProChip Designer | Kubva pane huru ProChip hwindo menyu… |
| Help | Sarudza Help > Prochip Mugadziri Rubatsiro. |
| Tutorials | Sarudza Help > Tutorials. |
| Anozivikanwa Matambudziko uye Mhinduro | Sarudza Help > Review KPS. |
Atmel WinCUPL Software
Tafura 9. WinCUPL References uye Tsigiro
| WinCUPL | Kubva pane huru WinCUPL hwindo menyu… |
| Help | Sarudza Help > Zviri mukati. |
| CUPL Programmers Reference Guide | Sarudza Help > CUPL Programmers Reference. |
| Tutorials | Sarudza Help > Atmel Info > Tutorial1.pdf. |
| Anozivikanwa Matambudziko uye Mhinduro | Sarudza Help > Atmel Info > CUPL_BUG.pdf. |
Atmel ATMISP Software
Tafura 10. ATMISP References uye Tsigiro
| ATMISP | Kubva pane yakakura ATMISP hwindo menyu… |
| Help Files | Sarudza Help > ISP Rubatsiro. |
| Tutorials | Sarudza Help > ATMISP Tutorial. |
| Anozivikanwa Matambudziko uye Mhinduro | Uchishandisa Windows Explorer browser, tsvaga ATMISP folda uye vhura iyo readme.txt file ine ASCII text editor. |
Atmel POF2JED Shanduko Software
Tafura 11. POF2JED References uye Tsigiro
| POF2JED | Kubva pane yakakura POF2JED hwindo menyu… |
| ATF15xx Shanduko Yechikumbiro Pfupi | Sarudza Help > Sarudzo dzekushandura. |
Technical Support
- Kuti uwane rutsigiro rwehunyanzvi pane chero nyaya dzine chekuita neAtmel PLD, bata Atmel PLD Applications Group pa:
- Email pld@atmel.com
- Nharembozha (+1)408-436-4333
- Online Support Form http://support.atmel.com/bin/customer.exe
Revision History
| Kudzokorora | Date | Tsanangudzo |
| 3605C | 06/2014 | Gadziridza schematics, template, logos, uye disclaimer peji. Wedzera chikamu cheRevision History. |
| 3605B | 05/2008 |
- Atmel Corporation 1600 Technology Drive, San Jose, CA 95110 USA T: (+1)(408) 441.0311 F: (+1)(408) 436.4200 | www.atmel.com
- © 2014 Atmel Corporation. / Rev.: Atmel-3605C-CPLD-ATF15xx-DK3-Development-Kit-UserGuide_062014.
- Atmel®, Atmel logo uye musanganiswa wayo, Kugonesa Unlimited Mikana, uye zvimwe zvikwangwani zvakanyoreswa kana zviratidzo zveAtmel Corporation muUS uye
dzimwe nyika. Mamwe mazwi uye mazita echigadzirwa anogona kunge ari zviratidzo zvevamwe. - ZVINOTAURWA: Ruzivo rwuri mugwaro iri rwunopihwa maererano neAtmel zvigadzirwa. Hapana rezinesi, kutaura kana kurehwa, ne estoppel kana neimwe nzira, kune chero kodzero yepfuma inopihwa negwaro iri kana zvine chekuita nekutengeswa kwezvigadzirwa zveAtmel.
- KUNZE SEZVAKATAURWA MUMITEMO YEATMEL NEZVINHU ZVINHU ZVINOITWA PAATMEL. WEBSITI, ATMEL HAItore ZVINHU ZVINHU ZVOSE UYE HAIZVI ZVINHU ZVINOTAURWA, ZVINOITWA, KANA ZVINHU ZVAKAITWA NEZVINHU ZVAKAITWA NEZVINHU ZVINO zvinosanganisira, ASI ZVISI ZVINOGWARWA, ZVINOITWA WARANTY YEKUTENGWA, KUKONZERA, KUBATSIRWA NEBATIZO. IN
- HAPANA CHIITIKO CHINOGONA KUTI ATMEL INE MHOSVA YEKUNHU CHETE, ZVINODA, ZVINOTEVERA, chirango, CHAKATAURWA, KANA ZVINOITIKA KUKABASWA (kusanganisira, PASINA ZVINOGONESA, KUNYANYA KUKURASIKA UYE MUNHU, KUKANGANISWA KWEBHAZINISI, KANA KUSHANDISA RUZVO) CHINYORWA ICHI, KUNYANGE KANA ATMEL YAKANGA RACHIPIRWA ZVINOGONA KUKABVA KWAKADA.
- Atmel haiite zvinomiririra kana waranti zvine chekuita nekurongeka kana kukwana kwezviri mukati meizvi
gwaro uye inochengetedza kodzero yekuita shanduko kune zvakatemwa uye kutsanangurwa kwechigadzirwa chero nguva pasina chiziviso. Atmel haiite chero kuzvipira kugadzirisa ruzivo rwurimo. Kunze kwekunge zvakapihwa neimwe nzira, zvigadzirwa zveAtmel hazvina kukodzera, uye hazvizo shandiswe mukati, mota dzekushandisa. Zvigadzirwa zveAtmel hazvina kuitirwa, kupihwa mvumo, kana kupihwa mvumo yekushandisa sezvikamu mumashandisirwo anoitirwa kutsigira kana kuchengetedza hupenyu. - KUDZIVIRIRA-CHINOKOSHA, MUKURU, UYE ZVINHU ZVINHU ZVINHU ZVINHU ZVINHU ZVINHU ZVINHU ZVINHU ZVINHU ZVINHU ZVINOKOSHA: Zvigadzirwa zveAtmel hazvina kugadzirirwa uye hazvizoshandiswe zvine chekuita nechero zvikumbiro apo kutadza kwezvigadzirwa zvakadaro zvinotarisirwa kukonzeresa kukuvara kwakanyanya kana kufa ("Safety-Critical Applications") pasina kunyorwa kwakanyorwa nemukuru weAtmel.
- mvumo. Chengetedzo-Yakakosha Zvishandiso zvinosanganisira, pasina muganho, midziyo yekutsigira hupenyu, uye masisitimu, zvishandiso kana masisitimu ekushanda kwezvivakwa zvenyukireya uye masisitimu ezvombo.
- Zvigadzirwa zveAtmel hazvina kugadzirwa kana kuitirwa kushandiswa mumauto kana aerospace application kana nharaunda kunze kwekunge yakanyatso kusarudzwa naAtmel segiredhi remauto. Zvigadzirwa zveAtmel hazvina kugadzirwa kana kuitirwa kuti zvishandiswe mumotokari kunyorera kunze kwekunge zvakanyatso tsanangurwa neAtmel segiredhi remotokari.
- Yakatorwa kubva: Arrow.com.
Zvinyorwa / Zvishandiso
 |
Atmel ATF15xx-DK3 CPLD Development/Programmer Kit [pdf] Bhuku reMushandisi ATF15xx-DK3 CPLD Development Programmer Kit, ATF15xx-DK3, CPLD Development Programmer Kit, Development Programmer Kit, Programmer Kit |
