DPT-Ctrl AIR HANDLING CONTROLLER
Mirayiridzo

NHUNGAMIDZO

Ndatenda nekusarudza HK Instruments DPT-Ctrl yakatevedzana mhepo inobata controller ine mutsauko kumanikidzwa kana kuyerera kwemhepo. Iyo DPT-Ctrl yakatevedzana PID controllers akagadzirirwa kuvaka otomatiki muHVAC/R indasitiri. Iine yakavakirwa-mukati controller yeDPTCtrl, zvinokwanisika kudzora kunogara kudzvanyirira kana kuyerera kwevateveri, VAV masisitimu kana d.ampers. Paunenge uchidzora mafambiro emhepo, zvinokwanisika kusarudza mugadziri wefeni kana yakajairika yekuyera probe ine K-kukosha.

APPLICATIONS

DPT-Ctrl akatevedzana maturusi anowanzo shandiswa muHVAC/R masisitimu e:

• Kudzora kusiyanisa kudzvanywa kana kuyerera kwemhepo mumhepo inobata masisitimu
• VAV zvikumbiro
• Kudzora kupaka garaji kunopedza mafeni

YAMBIRO

• VERENGA MIRAIRO IYI ZVAKANAKA USATI WAEDZA KUISA, KUSHANDA KANA KUSHANDISA MUCHITI UYU.
• Kutadza kucherekedza ruzivo rwekuchengetedza uye kutevedzera mirairo kunogona kuguma mukukuvadzwa KWAKO, RUFU, UYE / KANA KUPARADZIKA KWEZVINHU.
• Kuti udzivise kuvhunduka kwemagetsi kana kukuvadzwa kwemidziyo, bvisa magetsi usati waisa kana kusevhisi uye shandisa waya chete ine insulation yakayerwa kuti izere mudziyo unoshanda vol.tage.
• Kuti udzivise moto unogona kuitika uye/kana kuputika usashandise mumhepo inogona kupfuta kana kuputika.
• Chengetedza iyi mirairo kuitira ramangwana.
• Ichi chigadzirwa, kana chaiswa, chichava chikamu cheinjiniya sisitimu ine maratidziro uye maitiro ekuita zvisina kugadzirwa kana kudzorwa neHK Instruments. Review maapplication uye makodhi emunyika neemunharaunda kuti ave nechokwadi chekuti kuisirwa kuchave kushanda uye kwakachengeteka. Shandisa chete vane ruzivo uye ruzivo matekiniki kuisa mudziyo uyu.

SECIFICATIONS

Performance
Kururama (kubva kumanikidziro akaiswa):
Muenzaniso 2500:
Pressure <125 Pa = 1% + ±2 Pa
Pressure> 125 Pa = 1% + ±1 Pa
Muenzaniso 7000:
Pressure <125 Pa = 1.5% + ±2 Pa
Kudzvinyirira> 125 Pa = 1.5 % + ± 1 Pa (Kunyatsotsanangurwa kunosanganisira: kunyatsojeka, mutsara, hysteresis, kugadzikana kwenguva refu, uye kukanganisa kwekudzokorora)
Kudzvinyirira:
Uchapupu hwekumanikidza: 25 kPa
Kuputika kwemhepo: 30 kPa
Zero point calibration:
Otomatiki otomatiki kana bhatani remanyorero
Nguva yekupindura: 1.0-20 s, inosarudzwa kuburikidza nemenyu

Zvinotaurwa Nezvehunyanzvi

Media inoenderana:
Mhepo yakaoma kana magasi asina hutsinye
Controller parameter (inosarudzwa kuburikidza nemenyu):
Pa, kPa, bar, inWC, mmWC, psi
Flow units (sarudza kuburikidza nemenyu):
Vhoriyamu: m3 /s, m3 /hr,cfm,l/s
Velocity: m/s, ft/min
Chiyereso:
MEMS, hapana kuyerera-kuburikidza
Environment:
Kushanda tembiricha: -20…50 °C, -40C modhi: -40…50 °C
Models ine autozero calibration -5…50 °C
Tembiricha-inotsiviwa siyana 0…50 °C
Kuchengetedza tembiricha: -40…70 °C
Humidity: 0 kusvika 95 % RH, kwete condensing

Zvenyama

Dimensions:
Nyaya: 90.0 x 95.0 x 36.0 mm
Kurema: 150 g
Kukwirisa: 2 imwe neimwe 4.3 mm screw maburi, imwe yakatsvetwa
Zvekushandisa:
Nyaya: ABS Lid: PC
Muyero wekudzivirira: IP54 Ratidza 2-mutsara kuratidza (12 mavara / mutsara)
Mutsara 1: Nhungamiro yekudzora kubuda
Mutsara 2: Kumanikidza kana kuyerera kwemhepo kuyerwa, inosarudzwa kuburikidza nemenyu
Saizi: 46.0 x 14.5 mm Kubatana kwemagetsi: 4-screw terminal block
Waya: 0.2 mm1.5 (2 AWG)
Cable entry:
Kusununguka kwekutambudzika: M16
Knockout: 16 mm
Pressure fittings 5.2 mm barbed brass + High pressure - Low pressure

Zvemagetsi

Voltage:
Denderedzwa: 3-waya (V Kunze, 24 V, GND)
Kupinza: 24 VAC kana VDC, ± 10%
Kubuda: 0 V, inosarudzwa kuburikidza nejumper
Simba rekushandisa: <1.0 W, -40C
modhi: <4.0 W apo <0 °C
Kuramba kushoma: 1 k Iyezvino:
Denderedzwa: 3-waya (mA Kunze, 24 V, GND)
Kupinza: 24 VAC kana VDC, ± 10%
Kubuda: 4 mA, inosarudzwa kuburikidza nejumper
Simba rekushandisa: <1.2 W -40C
modhi: <4.2 W apo <0 °C
Maximum mutoro: 500 Minimum mutoro: 20

Conformance

Inosangana nezvinodiwa zve:

…………………………..CE:…………………………UKCA
EMC: 2014/30/EU…………………………………..SI 2016/1091
RoHS: 2011/65/EU…………………………………. SI 2012/3032
SVONDO: 2012/19/EU…………………………………….. SI 2013/3113

SCHEMATICS

DIMENSIONAL ZVINHU

INSTALLATION

1. Isa mudziyo munzvimbo yaunoda (ona nhanho 1).
2. Vhura chivharo uye fambisa tambo kuburikidza nekurerutsira uye batanidza waya kune terminal block (s) (ona danho 2).
3. Chishandiso chave kugadzirira kugadzirisa.

YAMBIRO! Isa simba chete mushure mekunge mudziyo waiswa waya zvakanaka.

KUKWEDZWA MUCHINA KUENDERERA

Mufananidzo 1 - Mounting orientation 

CHECHI 2: WIRING DIAGRAMS
Kuti CE itevedzere, tambo yekudzivirira yakadzikwa zvakanaka inodiwa.

1. Bvisa kusununguka kwekutambudzika uye fambisa tambo.
2. Batanidza waya sezvakaratidzwa mumufananidzo 2.
3. Simbisa kusununguka kwekunetseka.

Mufananidzo 2a - Wiring diagram
Mufananidzo 2b - Kusarudzwa kwemaitiro ekubuda: Sarudzo yakasarudzika 0 V kune ese ari maviri

Ctrl kubuda Pressure
Jumper yakaiswa kune maviri mapini ezasi kuruboshwe: 0 V inobuda yakasarudzwa kuti idzore kubuda
Jumper yakaiswa kune maviri mapini ekumusoro kuruboshwe: 4 mA inobuda yakasarudzwa yekudzora kubuda
Jumper yakaiswa kune maviri mapini ezasi kudivi rekurudyi: 0 V inobuda yakasarudzirwa kudzvanywa
Jumper yakaiswa kune maviri mapini ekumusoro kudivi rekurudyi: 4 mA inobuda yakasarudzirwa kudzvanywa
Danho rechitatu: KUGADZIRA

1. Shandisa Menyu yemudziyo nekudzvanya bhatani rekusarudza kwemasekonzi maviri.
2. Sarudza maitiro ekushanda emutongi: PRESSURE kana FLOW.
   Sarudza PRESSURE kana uchidzora mutsauko wekumanikidza.
   
3. Sarudza kumanikidza unit yekuratidzira uye kubuda: Pa, kPa, bar, WC kana WC.
   
4. Pressure output scale (P OUT). Sarudza kumanikidza kubuda chiyero kuti uvandudze sarudzo yekubuda.
   
5. Nguva yekupindura: Sarudza nguva yekupindura pakati pe1.0-20 s.
   
6. Sarudza iyo setpoint yemutongi.
7. Sarudza proportional bhendi zvinoenderana nezvinodiwa zvekushandisa kwako.
   
8. Sarudza yakakosha kuwana zvinoenderana neako mashandisirwo ekushandisa.
   
9. Sarudza nguva yekutora zvinoenderana nezvinodiwa zvekushandisa.
   
10. Dzvanya bhatani rekusarudza kubuda mumenyu uye kuchengetedza shanduko.
    

Sarudza FLOW paunenge uchidzora mafambiro emhepo.

KUGADZIRIRA KUENDERERA

1) Sarudza maitiro ekushanda emutongi
-Sarudza Mugadziri kana uchibatanidza DPT-Ctrl kune feni ine dzvinyiriro yekuyera matepi
-Sarudza Yakajairika probe kana uchishandisa DPT-Ctrl ine yakajairika kuyerwa probe inoteedzera fomula: q = k P (kureva FloXact)

2) Kana Common probe yakasarudzwa: sarudza zviyero zvekuyera zvinoshandiswa mufomula (aka Formula unit) (kureva l/s)

3) Sarudza K-kukosha a. Kana mugadziri akasarudzwa mudanho
1: Imwe neimwe fan ine chaiyo K-kukosha. Sarudza kukosha kweK kubva pane zvakatemwa nemugadziri we fan.
b. Kana iyo Common probe yakasarudzwa mudanho rekutanga: Yese yakajairika probe ine chaiyo K-kukosha.
Sarudza iyo K-kukosha kubva kune yakajairwa probe mugadziri anotsanangurwa.
Inowanikwa K-kukosha huwandu: 0.001…9999.000
4) Sarudza inoyerera unit yekuratidzira uye inobuda:
Kuyerera kwevhoriyamu: m3/s, m3/h, cfm, l/s
Velocity: m/s, f/min
5) Kuyerera kunobuda chiyero (V OUT): Sarudza iyo inoyerera inobuda chiyero kuti uvandudze kubuda kwekugadzirisa.

6) Nguva yekupindura: Sarudza nguva yekupindura pakati pe1.0 s.
7) Sarudza setpoint yemutongi.
8) Sarudza bhendi rakaenzana zvinoenderana nezvinodiwa zvekushandisa kwako.

9) Sarudza yakakosha kuwana zvinoenderana neako maratidziro ekushandisa.

10) Sarudza nguva yekutora zvinoenderana nezvinodiwa zvekushandisa.

11) Dzvanya bhatani rekusarudza kuti ubude mumenyu.
CHECHINA: ZEROING THE DEVICE

CHERECHEDZA! Nguva dzose zero mudziyo usati washandisa.
Kuti zero mudziyo sarudzo mbiri dziripo:

1. Manual Pushbutton zero-point calibration
2. Autozero calibration

Ko transmitter yangu ine autozero calibration? Ona iyo chigadzirwa label. Kana ikaratidza -AZ mune nhamba yemuenzaniso, saka une autozero calibration.

1. Manual Pushbutton zero-point calibration
   CHERECHEDZA: Mugove voltage inofanirwa kunge yakabatana ingangoita awa imwe isati yasvika zero poindi kugadzirisa.
   a) Bvisa machubhu ese ari maviri ekumanikidza kubva kumachiteshi akanyorwa + uye .
   b) Dzvanya pasi bhatani re zero kudzamara mwenje we LED (tsvuku) wabatidzwa uye chiratidziro chaverenga "zeroing" (inoratidza sarudzo chete). (ona mufananidzo 4)
   c) Iyo zeroing yechishandiso ichaenderera otomatiki. Zeroing inopera kana LED yadzima, uye chiratidziro chinoverenga 0 (chiratidziro sarudzo chete).
   d) Isazve machubhu ekumanikidza kuona kuti iyo Yepamusoro-kudzvanywa chubhu yakabatana nechiteshi chakanyorwa +, uye iyo Low-pressure chubhu yakabatana nechiteshi chakanyorwa -.

KUSVIRA MUCHINA KUENDERERA

2) Auto zero calibration
Kana mudziyo uchisanganisira sarudzo autozero wedunhu, hapana chiito chinodiwa.
Autozero calibration (-AZ) ibasa re autozero muchimiro che otomatiki zeroing wedunhu rakavakirwa muPCB board. Iyo autozero calibration yemagetsi inogadzirisa iyo transmitter zero panguva dzakafanotemerwa nguva (maminetsi gumi ega ega). Iro basa rinobvisa zvese zvinobuda chiratidzo chekudonha nekuda kwekupisa, zvemagetsi, kana zvemagetsi mhedzisiro, pamwe nekudiwa kwenyanzvi kubvisa yakakwira uye yakaderera-kudzvanywa machubhu kana ichiita yekutanga kana periodic transmitter zero point calibration. Iyo autozero gadziriso inotora 10 masekonzi mushure meiyo mudziyo unodzokera kune yayo yakajairika yekuyera maitiro. Munguva ye4-sekondi yekugadziridza nguva, iyo inobuda uye inoratidza kukosha ichaomesa kune yazvino kuyerwa kukosha. Matransmitters ane autozero calibration anenge asina kugadzirisa.

-40C MUFANANIDZO: KUSHANDA MUMUNHU INOtonhora

Chivharo chemudziyo chinofanira kuvharwa kana tembiricha yekushanda iri pasi pe0 °C. Chiratidziro chinoda maminetsi gumi nemashanu kuti chidziye kana chishandiso chatangwa mukupisa kuri pasi pe15 ° C.
CHERECHEDZA! Iko kushandiswa kwesimba kunokwira uye panogona kuve nekumwe kukanganisa kwe0,015 volts kana tembiricha yekushanda iri pasi pe0 ° C.

RECYCLING/KURASA

Zvikamu zvasara kubva pakuiswa zvinofanirwa kudzokororwa zvinoenderana nemirairo yenzvimbo yako. Zvishandiso zvakabviswa zvinofanirwa kuendeswa kunzvimbo yekudzokorodza iyo inonyanya kushandisa tsvina yemagetsi.

WARRANTY POLICY

Mutengesi anosungirwa kupa waranti yemakore mashanu yezvinhu zvinounzwa zvine chekuita nekugadzira uye kugadzira. Nguva yewaranti inofungidzirwa kutanga pazuva rekutumira rechigadzirwa. Kana kukanganisa kwezvinhu zvakasvibiswa kana kukanganisa kwekugadzirwa kunowanikwa, mutengesi anosungirwa, kana chigadzirwa chacho chichitumirwa kune mutengesi pasina kunonoka kana kuti nguva isati yapera waranti, kugadzirisa kukanganisa pakufunga kwake kana nekugadzirisa kukanganisa. chigadzirwa kana nekuendesa mahara kune mutengi chigadzirwa chitsva uye nekuchitumira kune mutengi. Mari yekuendesa kwekugadzirisa pasi pewaranti ichabhadharwa nemutengi uye mari yekudzorera nemutengesi. Iyo waranti haisanganisi kukuvadzwa kwakakonzerwa netsaona, mheni, mafashama kana chimwe chiitiko chechisikigo, kupfeka kwakajairwa uye kubvaruka, kubata zvisina kunaka kana kusava nehanya, kushandiswa zvisina kufanira, kuwandisa, kuchengetedza kwakashata, kutarisirwa kusirizvo kana kuvaka patsva, kana shanduko uye basa rekuisa risina kuitwa ne mutengesi. Kusarudzwa kwezvinhu zvezvishandiso zviri kuita ngura ibasa remutengi kunze kwekunge zvabvumiranwa zviri pamutemo. Kana mugadziri akachinja chimiro chemudziyo, mutengesi haasungirwe kuita shanduko dzakafanana nemidziyo yakatotengwa. Kukwidza nyaya yewaranti kunoda kuti mutengi aite nemazvo mabasa ake kubva pakuunza uye kutaurwa muchibvumirano. Mutengesi achapa waranti itsva yezvinhu zvakatsiviwa kana kugadziriswa mukati mewaranti, zvisinei chete nekupera kwenguva yewaranti yechigadzirwa chekutanga. Warranti inosanganisira kugadziriswa kwechikamu chakaremara kana mudziyo, kana kana zvichidikanwa, chikamu chitsva kana mudziyo, asi kwete kuisirwa kana kuchinjana mari. Pasina mamiriro ezvinhu mutengesi ane mhosva yekukuvadza muripo wekukuvara kusiri kwakananga.

Copyright HK Instruments 2022
www.hkinstruments.fi
Kuisa shanduro 11.0 2022

Zvinyorwa / Zvishandiso

HK Zviridzwa DPT-Ctrl AIR HANDLING CONTROLLER [pdf] Mirayiridzo DPT-Ctrl AIR HANDLING CONTROLLER, AIR HANDLING CONTROLLER, KUBATA MUTAURI.

References

• User Manual