Zviri mukati hide
1 Danfoss AK-CC 210 Controller Yekudzora Tembiricha
2 Nhanganyaya
3 Operation
4 Ongororo yemabasa
5 Operation
6 Ongororo yemenyu
7 FAQ
8 Zvinyorwa / Zvishandiso
8.1 References
9 Related Posts

Danfoss-logo

Danfoss AK-CC 210 Controller Yekudzora Tembiricha

Danfoss-AK-CC-210-Controller-For-Temperature-Control-chigadzirwa

Zvinotsanangurwa

  • Product: Controller yekudzora tembiricha AK-CC 210
  • Maximum yakabatana thermostat sensors: 2
  • Digital inputs: 2

Nhanganyaya

Application

  • Iyo controller inoshandiswa kudzora tembiricha yefiriji midziyo muzvitoro zvikuru
  • Nezvakawanda zvakafanotsanangurwa zvikumbiro imwe unit inokupa akawanda sarudzo. Flexibility yakarongwa zvese zvekuisa kutsva uye yekushandira mukutengeserana kwemafiriji

Danfoss-AK-CC-210-Controller-For-Temperature-Control- (1)

Principle
Iyo controller ine tembiricha yekudzora uko chiratidzo chinogona kugamuchirwa kubva kune imwe kana maviri tembiricha sensors.
Iyo thermostat sensors inogona kuiswa mumhepo inotonhora inoyerera mushure meevaporator, mumhepo inodziya inoyerera pamberi peevaporator, kana zvese zviri zviviri. Kugadzika kunozoratidza kuti masaini maviri anofanira kuva nesimba sei pakutonga.
Chiyero chekushisa kwe defrost chinogona kuwanikwa zvakananga kuburikidza nekushandiswa kweS5 sensor kana zvisina kunanga kuburikidza nekushandiswa kweS4 kuyerwa. Zvina zvinodzokororwa zvichacheka mabasa anodiwa mukati nekunze - iyo application inosarudza kuti ndeipi. Zvisarudzo ndezvizvi:

  • Refrigeration (compressor kana relay)
  • Fan
  • Defrost
  • Kupisa kwenjanji
  • Alarm
  • Chiedza
  • Mafeni ehotgas defrost
  • Refrigeration 2 (compressor 2 kana relay 2)

 

Danfoss-AK-CC-210-Controller-For-Temperature-Control- (2)

Zvikumbiro zvakasiyana-siyana zvinotsanangurwa papeji 6.

Advantages

  • Mazhinji maapplication ari mune imwecheteyo unit
  • Iyo controller yakabatanidza firiji-tekinoroji mabasa, kuitira kuti ikwanise kutsiva iyo yakazara muunganidzwa weiyo thermostats uye nguva.
  • Mabhatani uye chisimbiso zvakanyudzwa kumberi
  • Inogona kudzora compressors maviri
  • Nyore kukwidza data kutaurirana
  • Kurumidza kuseta
  • Mareferensi maviri etembiricha
  • Digital inputs kune akasiyana mabasa
  • Basa rewachi rine super cap backup
  • HACCP (Hazard Analysis uye Yakakosha Kudzora Mapoinzi)
    • Kutarisisa tembiricha uye kunyoreswa kwenguva ine tembiricha yakanyanya (onawo peji 19)
    • Fekitari calibration iyo inovimbisa kuyera kuri nani pane kutaurwa mune yakajairwa EN ISO 23953-2 isina kunotevera calibration (Pt 1000 ohm sensor)

Operation

Sensors
Anosvika maviri ethermostat sensors anogona kubatana kune controller. Iyo yakakodzera application inosarudza sei.

  • Sensor mumhepo pamberi peevaporator:
    Kubatana uku kunonyanya kushandiswa kana kutonga kwakavakirwa panzvimbo.
  • Sensor mumhepo mushure meiyo evaporator:
    Kubatana uku kunonyanya kushandiswa kana firiji ichidzorwa uye kune njodzi yekunyanya kuderera tembiricha pedyo nezvigadzirwa.
  • Sensor pamberi uye mushure me evaporator:
    Ichi chinongedzo chinokupa iwe mukana wekugadzirisa iyo thermostat, iyo alarm thermostat uye chiratidziro kune yakakodzera application. Chiratidzo kune thermostat, iyo alarm thermostat uye chiratidziro chakaiswa sehuremu hwehuremu pakati petembiricha mbiri, uye 50% ichave ex.ample ipai kukosha kwakafanana kubva kune ese ma sensor.
    Chiratidzo kune thermostat, iyo alarm thermostat uye chiratidziro chinogona kusetwa zvakazvimirira kubva kune mumwe.
  • Defrost sensor
    Chiratidzo chakanakisa chine chekuita nekupisa kweiyo evaporator inowanikwa kubva kune defrost sensor yakaiswa yakananga pane evaporator. Pano chiratidzo chinogona kushandiswa ne defrost function, kuitira kuti kupfupika uye kunonyanya kuchengetedza simba kunogona kuitika.
    Kana defrost sensor isingadikanwi, defrost inogona kumiswa zvichienderana nenguva, kana S4 inogona kusarudzwa.Danfoss-AK-CC-210-Controller-For-Temperature-Control- (3)

Kudzora kwema compressor maviri
Kudzora uku kunoshandiswa kudzora ma compressor maviri ehukuru hwakafanana. Nheyo yekudzora ndeyekuti imwe yemacompressor inobatanidza pa½ musiyano weiyo thermostat, uye imwe yacho pamusiyano uzere. Kana iyo thermostat ichicheka mucompressor nemaawa mashoma ekushanda inotangwa. Imwe compressor inongotanga mushure menguva yakatarwa kunonoka, kuitira kuti mutoro ugove wakaparadzaniswa pakati pavo. Kunonoka kwenguva kune zvakakosha kupfuura tembiricha.
Kana tembiricha yemhepo yadonha nehafu yemusiyano iyo compressor imwe inomira, imwe icharamba ichishanda uye isingamire kusvika tembiricha inodiwa yawanikwa.
Macompressor anoshandiswa anofanirwa kunge ari emhando inokwanisa kutanga kutarisana nekumanikidza kwakakwira.

Danfoss-AK-CC-210-Controller-For-Temperature-Control- (4)

  • Shanduko yereferensi yereferensi
    Muchishandiso chekukasira, semuenzanisoample, inoshandiswa kune akasiyana zvigadzirwa mapoka. Pano tembiricha referensi inoshandurwa zviri nyore nechiratidzo chekubata pane inopinza yedhijitari. Chiratidzo chinosimudza yakajairika thermostat kukosha nehuwandu hwakafanotsanangurwa. Panguva imwecheteyo miganhu yealarm ine kukosha kwakafanana inobviswa maererano.Danfoss-AK-CC-210-Controller-For-Temperature-Control- (5)

Digital inputs
Kune maviri edhijitari ekuisa ese ari maviri anogona kushandiswa kune anotevera mabasa:

  • Nyaya yekuchenesa
  • Door yekubata basa ine alarm
  • Kutanga defrost
  • Coordinated defrost
  • Shanduko-pamusoro pakati pemareferensi maviri ekushisa
  • Kutapuriranazve chinzvimbo cheanobatika kuburikidza nedata kutaurirana

Danfoss-AK-CC-210-Controller-For-Temperature-Control- (6)

Nyaya yekuchenesa basa
Iri basa rinoita kuti zvive nyore kutungamira mudziyo wefiriji kuburikidza nechikamu chekuchenesa. Kuburikidza nemapush matatu pane switch iwe unochinja kubva pane chimwe chikamu kuenda kune chinotevera chikamu.
Kusundidzira kwekutanga kunomisa firiji - mafeni anoramba achishanda

  • "Gare gare": Kusundidzira kunotevera kunomisa vateveri
  • "Zvichiri gare gare": Kusundidzira kunotevera kunotangazve firiji

Mamiriro akasiyana anogona kuteverwa pachiratidziro.
Pane network alarm yekuchenesa inotumirwa kune system unit. Iyi alarm inogona "logged" kuitira kuti humbowo hwekutevedzana kwezviitiko hupihwe.

Danfoss-AK-CC-210-Controller-For-Temperature-Control- (7)

Door contact basa
Mumakamuri anotonhora uye mumakamuri echando switch yemusuwo inogona kushandura mwenje nekudzima, tanga nekumisa firiji uye upe alarm kana gonhi rakaramba rakavhurika kwenguva yakareba.

Danfoss-AK-CC-210-Controller-For-Temperature-Control- (8)

Defrost
Zvichienderana nekushandiswa kwaungasarudza pakati peinotevera nzira dze defrost:

  • Zvisikwa: Pano mafeni anochengetwa achishanda panguva yechando
  • Magetsi: Chinhu chekudziya chinoitwa
  • Brine: Ivhavha inochengetwa yakashama kuitira kuti brine ikwanise kuyerera nemuevaporator
  • Hotgas: Pano solenoid mavharuvhu anodzorwa kuitira kuti hotgas kuyerera kuburikidza evaporator.

Danfoss-AK-CC-210-Controller-For-Temperature-Control-01

Kutanga kwe defrost

Defrost inogona kutanga nenzira dzakasiyana

  • Interval: Defrost inotangwa panguva yakatarwa, toti, awa yese yechisere
  • Nguva yefiriji:
    Defrost inotangwa panguva dzakatarwa dzenguva yefiriji, nemamwe mazwi, kushomeka kwakaderera kwefiriji "kuchamisa" defrost iri kuuya.
  • Purogiramu: Pano defrost inogona kutangwa panguva dzakatarwa dzemasikati neusiku. Zvisinei, max. 6 nguva
  • Kubata: Defrost inotangwa nechiratidzo chekubata pane inopinza yedhijitari
  • Network: Chiratidzo che defrost chinogamuchirwa kubva kune system unit kuburikidza neiyo data kutaurirana
  • S5 temp Muna 1: 1 masisitimu kushanda kweiyo evaporator kunogona kuteverwa. Icing-up inotanga defrost.
  • Manual: Iyo yakawedzera defrost inogona kuvhurwa kubva kune yakaderera-yakanyanya bhatani. (Kunyange zvisiri zvekushandisa 4).

Danfoss-AK-CC-210-Controller-For-Temperature-Control- (10)

Coordinated defrost
Pane nzira mbiri idzo coordinated defrost inogona kurongeka. Pamwe newaya yekubatanidza pakati pevanodzora kana kuburikidza nedata kutaurirana

Waya kubatana
Imwe yevatongi inotsanangurwa kuve iyo inodzora unit uye bhatiri module inogona kuiswa mairi kuitira kuti wachi ive nechokwadi chekuchengetedza. Kana defrost yatangwa mamwe ese ma controller anoteedzera uye zvakare otanga defrost. Mushure mekudzima dhizaini vatongi vega vanozoenda kunzvimbo yekumirira. Kana vese vange vakamirira panenge paine shanduko-pamusoro kune firiji.
(Kana mumwe chete muboka achida kuomeswa nechando, vamwe vanotevedzerawo).

Defrost kuburikidza nedata communication
Ese ma controller akarongedzerwa nedata yekutaurirana module, uye kuburikidza neanopfuura basa kubva pagedhi defrost inogona kurongeka.

Defrost paunoda

  1. Kubva pane firiji nguva
    Kana nguva yefiriji yakasanganiswa yapfuura nguva yakatarwa, defrost inotanga.
  2. Danfoss-AK-CC-210-Controller-For-Temperature-Control- (11)Kubva pane tembiricha
    Iyo controller inogara ichitevera tembiricha paS5. Pakati pekupisa kuviri tembiricha yeS5 inodzikira zvakanyanya iyo evaporator ice kumusoro (compressor inoshanda kwenguva yakareba uye inodhonza tembiricha yeS5 zvichidzika pasi). Kana tembiricha ikapfuura seti inobvumidzwa mutsauko iyo defrost ichatangwa.
    Iri basa rinogona kushanda chete mu1: 1 masisitimu Danfoss-AK-CC-210-Controller-For-Temperature-Control- (12)

Extra module

  • Iyo controller inogona mushure mekugadzirisa iyo yekuisa module kana application ichichida.
    Iyo controller yakagadzirwa neplug, saka module inongofanira kusundirwa mukati
    • Bhatiri module
      Iyo module inovimbisa voltage kumutongi kana voltaganofanira kusiya kweanopfuura maawa mana. Basa rewachi rinogona kuchengetedzwa panguva yekutadza kwemagetsi.
    • Kukurukurirana kwemashoko
      Kana iwe uchida kuvhiyiwa kubva kuPC, data yekukurukurirana module inofanirwa kuiswa mu controller.
  • Kuratidzwa kwekunze
    Kana zvichidikanwa kuratidza tembiricha pamberi pemudziyo wefiriji, mhando yekuratidzira EKA 163A inogona kuiswa. Iyo yekuwedzera inoratidza icharatidza ruzivo rwakafanana neruratidziro rwemutongi, asi haisanganisi mabhatani ekushanda. Kana kushanda kubva kuchiratidziro chekunze kuchidikanwa mhando yekuratidzira EKA 164A inofanira kuiswa.

Danfoss-AK-CC-210-Controller-For-Temperature-Control- (13)

Applications
Heino ongororo yenzvimbo yemutongi yekushandisa.

  • Kurongeka kunotsanangura zvinoburitswa kuitira kuti iyo controller interface inonangwa kune yakasarudzwa application.
  • Papeji 20 iwe unogona kuona marongero akakodzera eiyo akateedzana wiring madhayagiramu.
  • S3 uye S4 ma sensor tembiricha. Iko kushandiswa kuchasarudza-mugodhi kuti ingave imwe kana imwe kana ese ma sensors achashandiswa. S3 inoiswa mukuyerera kwemhepo pamberi peevaporator. S4 mushure meiyo evaporator.
  • Percentage setting ichasarudza maererano nekutonga kunofanira kuvakirwa. S5 i sensor defrost uye inoiswa pane evaporator.
  • DI1 uye DI2 mabasa ekubatanidza anogona kushandiswa kune rimwe remabasa anotevera: basa remusuwo, alarm function, defrost start, yekunze main switch, husiku kushanda, shanduko ye thermostat referensi, kuchenesa mudziyo, kumanikidza firiji kana coordinated defrost. Ona mabasa muzvirongwa o02 uye o37.

Refrigeration control neimwe compressor
Iwo mabasa anochinjirwa kune madiki mafiriji masisitimu angave ari emidziyo yefiriji kana makamuri anotonhora.
Iwo matatu relay anogona kudzora firiji, defrost uye mafeni, uye yechina relay inogona kushandiswa kune chero alarm basa, mwenje kudzora kana njanji kupisa kupisa.

  • Iyo alarm basa rinogona kubatanidzwa pamwe nekubata basa kubva pamusuwo switch. Kana gonhi rikaramba rakavhurika kwenguva yakareba kupfuura rakaderedzwa pachava nearamu.
  • Iyo mwenje control inogona zvakare kubatanidzwa kumusoro neyekusangana basa kubva pamusuwo switch. Gonhi rakavhurika rinobatidza mwenje uye rinoramba rakabatidzwa kwemaminetsi maviri mushure mekunge musuwo wavharwa zvakare.
  • Iyo njanji inopisa basa inogona kushandiswa mufiriji kana midziyo yekuomesa nechando kana pamusuwo wekudziya wemukati wemakamuri echando.

Iwo mafeni anogona kumiswa panguva ye defrost uye ivo vanogona zvakare kutevera yakavhurika yemusuwo / yekuvhara mamiriro.
Kune akati wandei mamwe mabasa earamu basa pamwe nekudzora kwemwenje, njanji yekudzivirira kupisa uye mafeni. Ndokumbira utarise kune mamwe marongero.

Danfoss-AK-CC-210-Controller-For-Temperature-Control- (14) Kupisa gasi defrost
Rudzi urwu rwekubatanidza runogona kushandiswa pamasisitimu ane hotgas defrost, asi mudiki masisitimu mukati, toti, masupamaketi - iyo inoshanda yemukati haina kuchinjirwa kune masisitimu ane mhosva huru. Relay 1's shanduko-pamusoro basa inogona kushandiswa neiyo bypass valve uye / kana hotgas valve.
Relay 2 inoshandiswa kune firiji.

Danfoss-AK-CC-210-Controller-For-Temperature-Control- (15) Danfoss-AK-CC-210-Controller-For-Temperature-Control- (16) vDanfoss-AK-CC-210-Controller-For-Temperature-Control- (17) Danfoss-AK-CC-210-Controller-For-Temperature-Control- (18)

Ongororo yemabasa

Function Para- mita Parameter nekushanda kuburikidza nekukurukurirana kwedata
Zvakajairika kuratidza
Kazhinji kukosha kwekushisa kubva kune imwe yeaviri thermostat sensors S3 kana S4 kana musanganiswa wezviyero zviviri zvinoratidzwa.

Mu o17 chiyero chinotarirwa.

 Ratidza mhepo (u56)
Thermostat Thermostat control
Isa poindi

Regulation yakavakirwa pane yakatarwa kukosha pamwe nekutamiswa, kana zvichibvira. Kukosha kunoiswa kuburikidza nekudzvanya pane bhatani repakati.

Ukoshi hweseti hunogona kukiyiwa kana kuganhurirwa kune zvimiro zvine r02 uye r 03. Referensi chero nguva inogona kuonekwa mu "u28 Temp. ref"

 Cheka °C
Differential

Kana tembiricha yakakwira kupfuura referensi + iyo set differential, iyo compressor relay ichachekwa mukati. Inocheka zvakare kana tembiricha yadzika kune yakatarwa referensi.

Danfoss-AK-CC-210-Controller-For-Temperature-Control- (19)

 r01 Differential
Setpoint limitation

Iyo controller yekumisikidzwa kweiyo setpoint inogona kuderedzwa pasi, kuitira kuti yakawandisa kana yakanyanya kuderera kukosha haigadzirwe netsaona - nekukanganisa kunokonzeresa.
Kuti udzivise yakanyanyisa kugadzika kweiyo setpoint, iyo max. kukosha kwereferensi kunobvumidzwa kunofanirwa kudzikiswa. r02 Kunyanya kucheka °C
Kuti udzivise kudzika kwakanyanya kweiyo setpoint, iyo min. kukosha kwereferensi kunobvumidzwa kunofanirwa kuwedzerwa. r03 Min cutout °C
Kugadziriswa kwe tembiricha yekuratidzira

Kana tembiricha pane zvigadzirwa uye tembiricha inogamuchirwa nemutungamiriri haina kufanana, gadziriso yekumisa yeakaratidzwa tembiricha inogona kuitwa.

 r04 Disp. Adj. K
Tembiricha unit

Gara pano kana controller iri kuratidza kukosha kwekushisa mu °C kana mu °F.

 r05 Temp. unit

°C=0. / °F=1

(Chete °C paAKM, chero marongero)
Kugadziriswa kwechiratidzo kubva kuS4

Kubhadhara mukana kuburikidza netambo refu sensor

 r09 Gadzirisa S4
Kugadziriswa kwechiratidzo kubva kuS3

Kubhadhara mukana kuburikidza netambo refu sensor

 r10 Gadzirisa S3
Kutanga / kumira kwefiriji

Nekuseta iyi firiji inogona kutangwa, kumiswa kana kudhindwa kwechinyorwa kwezvinobuda kunogona kubvumidzwa.

Kutanga / kumira kwefiriji kunogonawo kuitwa neiyo yekunze switch switch yakabatana neDI yekuisa.

Firiji yakamiswa ichapa "Aramu yekumira".

 r12 Main Chinja

 

1: Tanga

0: Mira

-1: Manual kutonga kwezvinobuda zvinotenderwa
Kudzosa kukosha kwehusiku

Referensi ye thermostat ndiyo ichave iyo yekuseta uye kukosha uku kana mutongi achinja kuita basa rehusiku. (Sarudza kukosha kwakashata kana paine kutonhora kuunganidza.)

 r13 Night offset
Kusarudzwa kwe thermostat sensor

Pano iwe unotsanangura iyo sensor iyo thermostat ndeyekushandisa kwayo kutonga basa. S3, S4, kana musanganiswa wavo. Nekugadzika 0%, S3 chete ndiyo inoshandiswa (Chivi). Ne 100%, chete S4. (Kushandisa 9 S3 sensor inofanira kushandiswa)

 r15 Ther. S4 %
Kupisa basa

Basa rinoshandisa defrost function's heat element yekusimudza tembiricha. Basa rinopinda musimba madhigirii akati wandei (r36) pazasi pereferensi chaiyo uye inocheka zvakare nekusiyanisa kwe2 madhigirii. Regulation inoitwa ne100% chiratidzo kubva kuS3 sensor. Mafeni achange achishanda kana paine kudziyisa. Mafeni uye basa rekudziya rinomira kana basa remusuwo rasarudzwa uye musuwo wakavhurwa.

Ikoko basa iri rinoshandiswa kunze kwekuchengetedza kucheka kunofanirawo kuiswa, kuitira kuti kupisa kwakanyanya kwechinhu chekupisa hakugone kuitika.

Rangarira kuseta D01 kune magetsi defrosting.Danfoss-AK-CC-210-Controller-For-Temperature-Control- (20)

 r36 HeatStartRel
Activation of reference displacement

Kana basa racho richinge rashandurwa kuita ON thermostat referensi richabviswa nekukosha mu r40. Activation inogonawo kuitika kuburikidza nekuisa DI1 kana DI2 (inotsanangurwa muo02 kana o37).Danfoss-AK-CC-210-Controller-For-Temperature-Control- (21)

 r39 Th. offset
Value of reference displacement

Iyo thermostat referensi uye maalarm values ​​anochinjirwa nhamba inotevera yemadhigirii kana kutamiswa kwaitwa. Activation inogona kuitika kuburikidza ner39 kana kuisa DI

 r40 Th. kukanganisa K
Husiku setbck (kutanga kwechiratidzo chehusiku)
Kumanikidzwa kutonhorera.

(kutanga kwekumanikidzwa kutonhora)
Alarm Alarm settings
Mutongi anogona kupa alarm mumamiriro akasiyana. Kana paine alarm ese malight-emitting diodes (LED) anopenya pane controller pamberi, uye alarm relay inocheka mukati. Nekutaurirana kwedata kukosha kwemaalarm ega ega kunogona kutsanangurwa. Kugadzika kunoitwa mu "Alarm destinations" menyu.
Alarm kunonoka (kunonoka alarm kunonoka)

Kana imwe yezvikamu zviviri zvemuganhu ikapfuudzwa, basa renguva richatanga. Iyo alarm haizoshanda kusvika nguva yakatarwa yapera. Nguva inononoka inoiswa mumaminitsi.

 A03 Alarm kunonoka
Nguva inononoka yearamu yemusuwo

Nguva inononoka inoiswa mumaminitsi.

Basa racho rinotsanangurwa mu o02 kana mu o37.

 A04 DoorOpen del
Nguva inononoka yekutonhodza (kunonoka alarm kwenguva refu)

Iyi nguva inononoka inoshandiswa panguva yekutanga-up, panguva yekudzivirira, pakarepo mushure mekugadzirisa. Pachave neshanduko-pamusoro kune yakajairwa nguva kunonoka (A03) kana tembiricha yadzikira pazasi peyepamusoro alarm yakatarwa.

Nguva inononoka inoiswa mumaminitsi.

 A12 Pulldown del
Upper alarm limit

Pano iwe unoseta apo alarm yekushisa kwepamusoro ichatanga. Muganho kukosha wakaiswa mu °C (absolute value). Iko kukosha kwekugumira kuchasimudzwa panguva yekushanda kwehusiku. Hukoshi hwakafanana nehwekudzoserwa husiku, asi huchasimudzwa chete kana kukosha kuri kuita.

Iko kukosha kwemuganho kuchasimudzwawo maererano nereferensi yekubvisa r39.

 A13 HighLim Air
Lower alarm limit

Pano iwe unoseta apo alarm yekudziya yakaderera ichatanga. Muganho kukosha wakaiswa mu °C (absolute value).

Iko kukosha kwemuganho kuchasimudzwawo maererano nereferensi yekubvisa r39.

 A14 LowLim Air
Kunonoka kwe DI1 alarm

Iyo yekucheka-kunze / yekucheka-mukati inozokonzera alarm kana nguva yekunonoka yapfuura. Basa racho rinotsanangurwa mu o02.

 A27 AI.Kunonoka DI1
Kunonoka kwe DI2 alarm

Iyo yekucheka-kunze / yekucheka-mukati inozokonzera alarm kana nguva yekunonoka yapfuura. Basa racho rinotsanangurwa mu o37

 A28 AI.Kunonoka DI2
Chiratidzo kune alarm thermostat

Pano iwe unofanirwa kutsanangura chiyero pakati pema sensors ayo alarm thermostat inofanirwa kushandisa. S3, S4 kana musanganiswa weaya maviri.

Nekugadzika 0% chete S3 ndiyo inoshandiswa. Ne 100% chete S4 inoshandiswa

 A36 Alamu S4%
Reset alarm
EKC kukanganisa
Compressor Compressor control
Iyo compressor relay inoshanda pamwe chete neiyo thermostat. Kana iyo thermostat ichidaidza firiji iyo compressor relay ichashandiswa.
Nguva dzekumhanya

Kuti udzivise kushanda kusingaite, hunhu hunogona kusetwa kwenguva iyo compressor ichamhanya kana yatangwa. Uye kwenguva yakareba sei iyo inofanirwa kumiswa.

Nguva dzekumhanya hadzionekwe kana defrosts inotanga.
Min. ON-nguva (mumaminitsi) c01 Min. Nenguva
Min. OFF-nguva (mumaminitsi) c02 Min. Off time
Nguva inononoka yekubatanidza kwema compressor maviri

Zvirongwa zvinoratidza nguva inofanirwa kupfuura kubva kune yekutanga relay kuchekwa mukati uye kusvika iyo inotevera relay inofanirwa kucheka mukati.

 c05 Nhanho kunonoka
Yakadzoserwa relay basa reD01

0: Yakajairika basa uko relay inocheka mukati kana firiji ichidiwa

1: Kudzoserwa basa uko relay inocheka kunze kana firiji ichidiwa (iyi wiring inoburitsa mhedzisiro yekuti pachave nefiriji kana iyo yekugovera vol.tage kune mutongi akundikana).

 c30 Cmp relay NC
Iyo LED kumberi kwemutongi icharatidza kana firiji iri kuitika. Comp Relay

Pano iwe unogona kuverenga mamiriro eiyo compressor relay, kana iwe unogona kumanikidza- kudzora relay mu "Manual control" modhi.
Defrost Defrost control
  • Iyo controller ine timer basa iri zeroset mushure mega ega defrost kutanga. Iyo timer basa ichatanga defrost kana / kana nguva yepakati yapfuura.
  • Basa renguva rinotanga kana voltage yakabatana nemutongi, asi inoraswa kekutanga nekumisikidza mu d05.
  • Kana pane kutadza kwemagetsi kukosha kwenguva kuchachengetwa uye kuenderera kubva pano kana simba radzoka.
  • Iri basa renguva rinogona kushandiswa senzira iri nyore yekutanga defrosts, asi inogara ichiita sekuchengetedza defrost kana imwe yeinotevera defrost inotanga isina kugamuchirwa.
  • Iyo controller inewo chaiyo-nguva wachi. Kuburikidza nemagadzirirwo ewachi ino uye nguva dzenguva dzinodiwa dzechando, defrost inogona kutangwa panguva dzakatarwa dzezuva. Kana paine njodzi yekukundikana kwesimba kwenguva yakareba kupfuura maawa mana, bhatiri module inofanirwa kuiswa mu controller.
  • Defrost kutanga inogonawo kuitwa kuburikidza nedata kutaurirana, kuburikidza nemasaini ekusangana kana bhuku rekutanga-up.
  • Nzira dzese dzekutanga dzichashanda mu controller. Iwo akasiyana mabasa anofanirwa kuiswa, kuitira kuti defrosts "irege "kudonha" imwe mushure meimwe.
  • Defrost inogona kuitwa nemagetsi, hotgas kana brine.
  • Iyo chaiyo defrost ichamiswa zvichienderana nenguva kana tembiricha ine chiratidzo kubva kune tembiricha sensor.
Defrost nzira
  • Pano unoisa kuti defrost inofanira kuitwa nemagetsi, gasi, brine kana "kwete".
  • Munguva ye defrost iyo defrost relay inochekwa mukati.
  • (Ne brine iyo "firiji yekudzora valve" ichachengetwa yakavhurika panguva yekudonha)
 d01 Def. nzira 0 = kwete

1 = El

2 = Gasi

3= Mvura
Defrost stop tembiricha

Iyo defrost inomiswa pane imwe tembiricha inoyerwa ne sensor (sensor inotsanangurwa mu d10).

Kukosha kwekushisa kwakaiswa.

 d02 Def. Stop Temp
Kupindirana pakati pe defrost kunotanga
  • Basa iri zero set uye richatanga iyo timer basa pane yega defrost kutanga. Kana nguva yapera basa rinotanga defrost.
  • Iro basa rinoshandiswa seyakareruka defrost kutanga, kana rinogona kushandiswa sechidziviriro kana yakajairika chiratidzo chikatadza kuoneka.
  • Kana tenzi / muranda defrost pasina wachi kana pasina kutaurirana data inoshandiswa, nguva yepakati ichashandiswa semax. nguva pakati pe defrosts.
  • Kana defrost inotanga kuburikidza nedata kutaurirana ikasaitika, nguva yepakati ichashandiswa semax. nguva pakati pe defrosts.
  • Kana paine defrost nebasa rewachi kana kutaurirana kwedata, nguva yekupindirana inofanirwa kuisirwa imwe nguva yakati rebei kupfuura yakarongwa, sezvo nguva yepakati ichizotanga defrost iyo gare gare inoteverwa neyakarongwa.
  • Mukubatana nekukundikana kwesimba nguva yepakati ichachengetwa, uye kana simba richidzoka nguva yepakati ichaenderera mberi kubva kune yakachengetedzwa kukosha.
  • Nguva yepakati haisi kushanda kana yaiswa ku0.
 d03 Def Interval (0=off)
Max. defrost duration

Kugadzika uku inguva yekuchengetedza kuitira kuti defrost imiswe kana pasati pave nekumira zvichienderana netembiricha kana kuburikidza necoordinated defrost.

 d04 Max Def. nguva
Nguva staggering ye defrost cut ins panguva yekutanga-up
  • Basa racho rinongoenderana chete kana uine akati wandei mafiriji midziyo kana mapoka kwaunoda kuti defrost ive s.tagzvakabatanidzwa kune mumwe nemumwe. Basa racho rinonyanya kushanda chete kana wakasarudza defrost ne interval start (d03).
  • Basa racho rinononoka nguva yenguva d03 nehuwandu hwemaminetsi, asi inongozviita kamwe chete, uye izvi panguva yekutanga defrost inoitika kana vol.tage yakabatanidzwa kune controller.
  • Basa racho richave rinoshanda mushure mekutadza kwega kwega kwesimba.
 d05 Nguva Stagg.
Nguva yekuzorora

Pano iwe unoseta iyo nguva yekupfuura kubva ku defrost uye kusvika iyo compressor ichitanga zvakare. (Nguva iyo mvura inodonha kubva pa evaporator).

 d06 DripOff nguva
Kunonoka kwe fan kunotanga mushure mekudzima

Pano iwe unoisa iyo nguva yekupfuura kubva compressor kutanga mushure me defrost uye kusvika fan yatanga zvakare. (Nguva iyo mvura "yakasungirirwa" kune evaporator).

 d07 FanStartDel
Fani inotanga tembiricha

Iyo fan inogona zvakare kutangwa zvishoma zvisati zvambotaurwa pasi pe "Kunonoka kwe fan kutanga mushure mekunyungudika", kana iyo defrost sensor S5 inonyoresa kukosha kwakaderera pane iyo yakaiswa pano.

 d08 FanStartTemp
Fani inocheka mukati panguva yekudzima

Pano iwe unogona kuseta kana fan ichashanda panguva ye defrost. 0: Yakamiswa (Inomhanya panguva yepombi pasi)

  1. Kumhanya (kunomiswa panguva ye "fan kunonoka")
  2. Kumhanya panguva yepombi pasi uye defrost. Mushure mezvo zvakamira
 d09 FanDuringDef
Defrost sensor

Pano iwe unotsanangura iyo defrost sensor. 0: Hapana, defrost inoenderana nenguva 1: S5 2: S4

 d10 DefStopSens.
Kunonoka kwepombi

Isa nguva iyo evaporator inodururwa mufiriji isati yasvika.

 d16 Pombi dwn del.
Kunonoka kwemvura (chete maererano nehotgas)

Seta nguva iyo evaporator inodururwa mufiriji yakanyungudutswa mushure meiyo defrost.

 d17 Drin del
Defrost pane zvinodiwa - aggregate firiji nguva

Set pano ndiyo nguva yefiriji inobvumirwa pasina defrosts. Kana nguva yapera, defrost inotanga.

Nekugadzika = 0 basa rinotemwa.

 d18 MaxTherRunT
Defrost pakudiwa - S5 tembiricha

Iyo controller ichatevera kushanda kweiyo evaporator, uye kuburikidza nemukati maverengero uye zviyero zveS5 tembiricha inozokwanisa kutanga defrost kana shanduko yeS5 tembiricha yakura kupfuura zvinodiwa.

Pano iwe unoisa kuti yakakura sei slide yeS5 tembiricha inogona kubvumidzwa. Kana kukosha kwapfuura, defrost inotanga.

Iro basa rinogona kushandiswa chete mu1: 1 masisitimu kana tembiricha inoputika ichidzika kuti ive nechokwadi chekuti tembiricha yemhepo inochengetedzwa. Mukati megadziriro basa rinofanira kutemwa.

Nekugadzika = 20 basa rinotemwa

 d19 CucutS5Dif.
Kunonoka kwejekiseni rinopisa gasi

Inogona kushandiswa kana mavheti emhando yePMLX neGPLX ashandiswa. Nguva yakagadzirirwa kuitira kuti valve ivhare zvachose musati gasi rinopisa risati ravhurwa.

 d23 —
Kana iwe uchida kuona tembiricha pane defrost sensor, pusha bhatani remutongi rakaderera- rakawanda. Defrost temp.
Kana uchida kutanga imwe defrost, pusher's lowermost bhatani kwemasekonzi mana.

Iwe unogona kumisa defrost inoenderera nenzira imwechete

 Def Start

Pano unogona kutanga defrost yemanyorero
Iyo LED kumberi kwemutongi inoratidza kana defrost iri kuitika. Defrost Relay

Pano iwe unogona kuverenga iyo defrost relay mamiriro kana iwe unogona kumanikidza-kudzora relay mu "Manual control" maitiro.
Bata Mushure meDef

Inoratidza ON kana controller iri kushanda necoordinated defrost.
Defrost State Status pane defrost

1= kupomba pasi / defrost
Fan Fan control
Fani yakamira pa cut-out compressor

Pano iwe unogona kusarudza kana fan ichizomiswa kana compressor yachekwa

 F01 Fan stop CO

(Hongu = Fani yakamira)
Kunonoka kwe fan kumira kana compressor yachekwa

Kana iwe wasarudza kumisa fan kana compressor yagurwa, unogona kunonoka kumira fan kana compressor yamira.

Pano unogona kuseta nguva yekunonoka.

 F02 Fan del. CO
Fani kumira tembiricha

Basa racho rinomisa mafeni mumamiriro ekukanganisa, kuitira kuti varege kupa simba kune mudziyo. Kana iyo defrost sensor ikanyoresa tembiricha yakakwira kupfuura iyo yakaiswa pano, mafani anomiswa. Pachave nekutanga-kutanga pa2 K pazasi peseti.

Basa racho harisi kushanda panguva ye defrost kana kutanga-up mushure me defrost. Nekugadzirisa +50 ° C basa racho rinokanganiswa.

 F04 FanStopTemp.
Iyo LED kumberi kwemutongi inoratidza kana fan iri kumhanya. Fan ataure

Pano iwe unogona kuverenga iyo fan relay mamiriro, kana kumanikidza-kudzora relay mu "Manual control" maitiro.
HACCP HACCP
HACCP tembiricha

Pano iwe unogona kuona kuyerwa kwekushisa kunotumira chiratidzo kune basa

 h01 HACCP temp.
Yekupedzisira yakanyanya kukwirisa HACCP tembiricha yakanyoreswa ine chekuita ne: (Kukosha kunogona kuverengerwa kunze).

H01: Tembiricha inodarika panguva yakajairika mutemo.

H02: Tembiricha inodarika panguva yekutadza kwemagetsi. Battery backup inodzora nguva. H03: Tembiricha inodarika panguva yekutadza kwemagetsi. Hapana kudzora nguva.

 h02 –
Nguva yekupedzisira tembiricha yeHACCP yakapfuudzwa: Gore h03 –
Nguva yekupedzisira tembiricha yeHACCP yakapfuurwa: Mwedzi h04 –
Nguva yekupedzisira tembiricha yeHACCP yakapfuudzwa: Zuva h05 –
Nguva yekupedzisira tembiricha yeHACCP yakapfuudzwa: Awa h06 –
Nguva yekupedzisira tembiricha yeHACCP yakapfuurwa: Minute h07 –
Yekupedzisira kudarika: Nguva mumaawa h08 –
Kupfuura kudarika: Nguva mumaminetsi h09 –
Peak tembiricha

Iyo yakanyanya kuyerwa tembiricha inoramba ichichengetwa kana tembiricha yadarika kukosha kwemuganho muh12. Iko kukosha kunogona kuverengerwa kusvika nguva inotevera iyo tembiricha inodarika kukosha kwemuganhu. Mushure mezvo inonyorwa pamusoro pezviyero zvitsva.

 h10 Max.temp.
Kusarudzwa kwebasa 0: Hapana HACCP basa

1: S3 uye / kana S4 inoshandiswa se sensor. Tsanangudzo inoitika muh14. 2: S5 inoshandiswa se sensor.

 h11 HACCP sensor
Alarm limit

Pano iwe unoisa kukosha kwekushisa uko HACCP basa rekupinda musimba. Kana kukosha kwave kwakakwirira kudarika yakatarwa, nguva inononoka inotanga.

 h12 HACCP muganhu
Kunonoka kwenguva kwearamu (chete panguva yemutemo wakajairwa). Kana nguva yekunonoka yapfuura alarm inovhurwa. h13 HACCP kunonoka
Kusarudzwa kwema sensors ekuyera

Kana iyo S4 sensor uye / kana iyo S3 sensor inoshandiswa, chiyero pakati pavo chinofanira kuiswa. Pakugadzika 100% chete S4 ndiyo inoshandiswa. Pakugadzika 0% chete S3 ndiyo inoshandiswa.

 h14 HACCP S4%
Yemukati defrosting hurongwa / wachi basa
(Haisi kushandiswa kana chirongwa chekunze chekudzikisa chikashandiswa kuburikidza nekukurukurirana kwemashoko.) Kusvikira kune imwe nguva nhanhatu inogona kugadzirirwa kuti defrost itange zuva rose.
Defrost kutanga, kugadzika kweawa t01-t06
Defrost start, minute setting (1 na 11 vari pamwechete, zvichingodaro) Kana zvese t01 kusvika t16 zvakaenzana 0 wachi haizotanga kuparara. t11-t16
Chaiyo-nguva wachi

Kuisa wachi kunongodiwa chete kana pasina data kutaurirana.

Muchiitiko chekukundikana kwesimba kwemaawa asingasviki mana, basa rewachi richaponeswa. Paunenge uchiisa bhatiri module basa rewachi rinogona kuchengetedza kwenguva refu.

Pane zvakare zuva rinoratidza rinoshandiswa kunyoresa kuyerwa kwekushisa.
Wachi: Kuronga kweawa t07
Clock: Minute setting t08
Clock: Date setting t45
Wachi: Mwedzi kurongwa t46
Clock: Year setting t47
Miscellaneous Miscellaneous
Kunonoka kwechiratidzo chekubuda mushure mekutanga-up

Kutanga-kumusoro mushure mekutadza kwemagetsi mabasa emutongi anogona kunonoka kuitira kuti kuwedzeredza kweiyo magetsi ekupa network kudziviswa.

Pano unogona kuseta nguva yekunonoka.

 o01 DelayOfOutp.
Digital yekupinza chiratidzo - DI1

Iyo controller ine yedhijitari yekupinda 1 iyo inogona kushandiswa kune imwe yeanotevera mabasa:

Kudzimwa: Kuiswa hakushandiswe

  1. Status kuratidza yekubata basa
  2. Basa remukova. Kana chinopinza chavhurwa chinoratidza kuti gonhi rakavhurika. Firiji nemafeni zvinomiswa. Kana nguva yekumisikidza mu "A4" yapfuura, alarm ichapihwa uye firiji ichatangwazve.
  3. Door alarm. Kana chinopinza chavhurwa chinoratidza kuti gonhi rakavhurika. Kana nguva yekumisikidza mu "A4" yapfuura, pachave ne alarm.
  4. Defrost. Basa rinotangwa nechiratidzo chepulse. Iyo controller inonyoresa kana iyo DI inoiswa. Mutongi anobva atanga defrost cycle. Kana iyo chiratidzo ichizogamuchirwa nevatongi vakati wandei zvakakosha kuti ZVINHU zvinongedzo zvigadzirwe nenzira imwechete (DI kuenda kuDI uye GND kuGND).
  5. Main switch. Mutemo unoitwa kana iyo yekuisa ipfupi-yakatenderedzwa, uye mutemo unomiswa kana iyo inopinza yakaiswa mu pos. DZIMA.
  6. Kuvhiya kweusiku. Kana iyo yekupinza ipfupi-inotenderera, pachava nemutemo wekushanda kwehusiku.
  7. Reference displacement kana DI1 iri pfupi-yakatenderedzwa. Kubviswa ne "r40".
  8. Separate alarm function. Alarm ichapihwa kana mapindiro acho akapfupikiswa.
  9. Separate alarm function. Alarm ichapihwa kana mapindiro avhurwa. (Kune 8 ne9 nguva inononoka yakaiswa muA27)
  10. Nyaya yekuchenesa. Basa rinotangwa nechiratidzo chepulse. Cf. zvakare tsananguro iri papeji 4.
  11. Kumanikidzirwa firiji pahotgas defrost kana kupinza kuri kupfupi-kutenderera.
 o02 DI 1 Config.

Tsanangudzo inoitika nehukoshi hwenhamba hunoratidzwa kuruboshwe.

 

(0 = kure)

 

 

 

DI mamiriro (Chiyero)

Iyo DI yekupinda mamiriro iripo inoratidzwa pano. ON or OFF.
  • Kana mutongi akavakirwa mumambure ane data kutaurirana, inofanira kunge iine kero, uye tenzi gedhi rekutaurirana kwedata rinofanirwa kuziva kero iyi.
  • Aya marongero anogona chete kuitwa kana data data module yakaiswa mu controller uye kuiswa kweiyo data yekutaurirana tambo kwapera.
  • Kuiswa uku kunotaurwa mune imwe gwaro "RC8AC".
  • Kero inoiswa pakati pe1 ne60 (119), gedhi rakatemwa
  • Kero inotumirwa kugedhi kana menyu yaiswa mu pos. ON
  • ZVINOKOSHA: Usati waisa o04, UNOFANIRA kuseta o61. Zvikasadaro unenge uchitumira- data isiriyo.
 Mushure mekugadzwa kweiyo data yekukurukurirana module mutongi anogona kushanda zvakaenzana nevamwe vanodzora muADAP-KOOL® mafiriji ekudzora.
o03
o04
Kupinda kodhi 1 (Kuwana kune ese magadzirirwo)

Kana zvigadziriso zviri mucontroller zvichifanira kuchengetedzwa nekodhi yekuwana iwe unogona kuseta nhamba yenhamba pakati pe0 ne100. Kana zvisina kudaro, unogona kukanzura basa racho nekuisa 0.

(99 inogara ichikupa iwe kupinda).

 o05 –
Sensor type

Kazhinji sensor yePt 1000 ine chiratidzo chikuru chechokwadi inoshandiswa. Asi iwe unogona zvakare kushandisa sensor neimwe chiratidzo chechokwadi. Iyo inogona kunge iri PTC 1000 sensor (1000 ohm) kana NTC sensor (5000 Ohm pa25°C).

Ese ma sensors akaiswa anofanirwa kunge ari emhando imwe chete.

 o06 SensorConfig Pt = 0

PTC = 1

NTC = 2
Ratidza nhanho

Hongu: Inopa matanho e0.5 ° Kwete: Inopa matanho e0.1 °

 o15 Disp. Nhanho = 0.5
Max. standby nguva mushure coordinated defrost

Kana controller yapedza defrost inomirira chiratidzo chinotaurira kuti firiji inogona kutangwazve. Kana chiratidzo ichi chikatadza kuoneka nechikonzero chimwe kana chimwe, controller inozotanga iyo firiji kana nguva yekumira iyi yapera.

 o16 Max HoldTime
Sarudza chiratidzo chekuratidzira S4%

Pano iwe unotsanangura chiratidzo chinoratidzwa nechiratidziro. S3, S4, kana musanganiswa weaya maviri.

Nekugadzika 0% chete S3 ndiyo inoshandiswa. Ne 100% chete S4.

 o17 Disp. S4%
Dhijitari yekuisa chiratidzo - D2

Iyo controller ine yedhijitari yekupinda 2 iyo inogona kushandiswa kune imwe yeanotevera mabasa:

Kudzimwa: Kupinza hakushandiswe.

  1. Status kuratidza yekubata basa
  2. Basa remukova. Kana chinopinza chavhurwa chinoratidza kuti gonhi rakavhurika. Firiji nemafeni zvinomiswa. Kana nguva yekumisikidza mu "A4" yapfuura, alarm ichapihwa uye firiji inotangazve.
  3. Door alarm. Kana chinopinza chavhurwa chinoratidza kuti gonhi rakavhurika. Kana nguva yekuseta mu "A4" yapfuura alarm ichapihwa.
  4. Defrost. Basa rinotangwa nechiratidzo chepulse. Iyo controller inonyoresa kana iyo DI inoiswa. Mutongi anobva atanga defrost cycle. Kana iyo chiratidzo ichizogamuchirwa nevatongi vakati wandei zvakakosha kuti ZVINHU zvinongedzo zvigadzirwe nenzira imwechete (DI kuenda kuDI uye GND kuGND).
  5. Main switch. Mutemo unoitwa kana iyo yekuisa ipfupi-yakatenderedzwa, uye mutemo unomiswa kana iyo inopinza yakaiswa mu pos. DZIMA.
  6. Kuvhiya kweusiku. Kana iyo yekupinza ipfupi-inotenderera, pachava nemutemo wekushanda kwehusiku.
  7. Reference displacement kana DI2 iri pfupi-yakatenderedzwa. Kubviswa ne "r40".
  8. Separate alarm function. Alarm ichapihwa kana mapindiro acho akapfupikiswa.
  9. Separate alarm function. Alarm ichapihwa kana mapindiro avhurwa.
  10. Nyaya yekuchenesa. Basa rinotangwa nechiratidzo chepulse. Cf. zvakare tsananguro iri papeji 4.
  11. Kumanikidzirwa firiji pahotgas defrost kana kupinza kuri kupfupi-kutenderera.
  12. Iko kupinza kunoshandiswa pakubatanidza defrost pamwe chete nemamwe ma controller emhando imwe chete
 o37 DI2 config.
Kugadziriswa kwebasa rechiedza (relay 4 muzvishandiso 2 ne6)
  1. Iyo relay inocheka mukati mukati mezuva rekushanda
  2. Iyo relay inofanirwa kudzorwa kuburikidza nedata kutaurirana
  3. The relay inofanira kudzorwa negonhi switch inotsanangurwa mune imwe o02 kana o37 apo kuiswa kunosarudzwa kune 2 kana 3. Kana gonhi razarurwa relay ichacheka mukati. Kana gonhi ravharwa zvakare pachava nenguva inononoka yemaminitsi maviri chiedza chisati chadzimwa.
 o38 Chiedza config
Activation yechiedza relay

Iyo mwenje relay inogona kuvhurwa pano, asi chete kana yakatsanangurwa mu o38 ine kuseta 2.

 o39 Remote chiedza
Kupisa kwenjanji panguva yekushanda kwezuva

Iyo ON nguva yakatarwa sechikamutage yenguva

 o41 Railh.ON zuva%
Kupisa kwenjanji panguva yekushanda kweusiku

Iyo ON nguva yakatarwa sechikamutage yenguva

 o42 Railh.ON ngt%
Rail kupisa kutenderera

Iyo nguva yenguva yeaggregate ON nguva + OFF nguva inoiswa mumaminetsi

 o43 Railh. cycle
Nyaya yekuchenesa
  • Mamiriro ebasa anogona kuteverwa pano kana basa rinogona kutangwa nemaoko.
  • 0 = Kushanda kwakajairika (hapana kuchenesa)
  • 1 = Kuchenesa nemafeni anoshanda. Mamwe mabudiro ese ari Off. 2 = Kuchenesa nemafeni akamira. Zvese zvinobuda zviri Off.

Kana basa racho richidzorwa nechiratidzo paDI1 kana DI2 yekuisa, chimiro chakakodzera chinogona kuoneka pano mumenyu.

 o46 Nyaya yakachena
Kusarudzwa kwekushandisa

Mutongi anogona kutsanangurwa nenzira dzakasiyana. Pano iwe unoseta kuti ndeipi pagumi maapplication anodiwa. Papeji 10 unogona kuona ongororo yezvikumbiro.

Iyi menyu inogona kuiswa chete kana mutemo wamiswa, kureva "r12" yakaiswa ku0.

 o61 — Appl. Mode (inongobuda muDanfoss chete)
Chinja seti yepresetting kune controller

Zvinokwanisika kusarudza kukurumidza kugadzirisa kwehuwandu hwema parameters. Zvinoenderana nekuti application kana kamuri inofanirwa kudzorwa uye kuti defrost ichamiswa zvichienderana nenguva kana zvichienderana nekushisa. Ongororo yacho inowanikwa papeji 22. Iyi menyu inogona kuiswa chete kana mutemo wamiswa, kureva "r12" yakaiswa ku0.

 

Mushure mekugadzirisa kukosha kuchadzokera ku 0. Chero chipi nechipi chinotevera kugadziriswa / kuiswa kwemaitiro kunogona kuitwa, sezvinodiwa.

 o62 –
Kuwana kodhi 2 (Kuwana zvigadziriso)

Pane mukana wekugadzirisa kwehukoshi, asi kwete kune zvigadziriso zvekugadzirisa. Kana zvigadziriso zviri mucontroller zvichizochengetedzwa nekodhi yekupinda unogona kuseta kukosha kwenhamba pakati pe0 ne100. Kana zvisina kudaro, unogona kukanzura basa racho nekuseta 0. Kana basa racho richishandiswa, pinda kodhi 1 (o05) anofanirawo kushandiswa.

 o64 –
Kopa marongero ezvino emutongi

Nebasa iri marongero emutongi anogona kuendeswa kune kiyi yekuronga. Kiyi inogona kuve neanosvika makumi maviri neshanu seti dzakasiyana. Sarudza nhamba. Zvese zvigadziriso kunze kweKushandisa (o25) uye Kero (o61) zvichakopwa. Kana kukopa kwatanga chiratidziro chinodzokera kuO03. Mushure memasekonzi maviri unogona kuenda mumenyu zvakare uye wotarisa kana kukopa kwacho kwaigutsa.

Kuratidza chimiro chisina kunaka kunoreva matambudziko. Ona kukosha muchikamu cheFault Message.

 o65 –
Kopa kubva pakiyi yepurogiramu

Iri basa rinodhawunirodha seti yezvigadziriso zvakambochengetwa mu controller. Sarudza nhamba yakakodzera.

Zvese zvigadziriso kunze kweKushandisa (o61) uye Kero (o03) zvichakopwa. Kana kukopa kwatanga chiratidziro chinodzokera kuO66. Mushure memasekonzi maviri iwe unogona kudzokera kumashure mumenyu zvakare uye tarisa kana kukopa kwacho kwaigutsa. Kuratidza chimiro chisina kunaka kunoreva matambudziko. Ona kukosha muchikamu cheMharidzo yeMharidzo.

 o66 –
Sevha segadziriro yepafekitari

Nekuseta uku unochengetedza marongero chaiwo emutongi seyokutanga kuseta (iyo yekutanga fekitori marongero akanyorwa pamusoro).

 o67 –
– – – Manheru Kudzora 0=Zuva

1=Husiku
Service Service
Tembiricha yakayerwa neS5 sensor u09 S5 temp.
Status pane DI1 kuisa. pa/1=yakavharwa u10 DI1 chimiro
Tembiricha yakayerwa neS3 sensor u12 S3 mhepo tembiricha
Mamiriro ekushanda kwehusiku (kubatidzwa kana kudzima) 1=yakavharwa u13 Night Cond.
Tembiricha yakayerwa neS4 sensor u16 S4 mhepo tembiricha
Thermostat tembiricha u17 Ther. mhepo
Verenga ikozvino regulation reference u28 Temp. ref.
Status pane DI2 inobuda. pa/1=yakavharwa u37 DI2 chimiro
Tembiricha inoratidzwa pachiratidziro u56 Ratidza mweya
Yakayerwa tembiricha yealarm thermostat u57 Mhepo yealarm
** Chimiro pane relay yekutonhodza u58 Comp1/LLSV
** Chimiro pane relay ye fan u59 Fan relay
** Chimiro pane relay ye defrost u60 Def. relay
** Chimiro pane relay yechitima u61 Railh. relay
** Chimiro pane relay yearamu u62 Alarm relay
** Chimiro pane relay yechiedza u63 Chiedza relay
** Chimiro pane relay yevharuvhu mumutsetse wekusveta u64 SuctionValve
** Chimiro pane relay ye compressor 2 u67 Comp2 relay
*) Hazvisi zvese zvinhu zvicharatidzwa. Chete basa rebasa rakasarudzwa rinoonekwa.
Mharidzo yemhosva Alarms
Mumamiriro ezvinhu ekukanganisa ma LED ari kumberi anopenya uye alarm relay inozoitwa. Kana iwe ukadzvanya bhatani repamusoro mune ino mamiriro iwe unogona kuona iyo alarm report muchiratidziro. Kana pane vakawanda ramba uchisunda kuti uvaone.

Kune marudzi maviri emaremo ekukanganisa - inogona kunge iri alarm inoitika panguva yekushanda kwemazuva ese, kana panogona kunge paine chakakanganisika mukuiswa.

A-aramu haizoonekwe kusvika nguva yakatarwa yapera.

E-alarm, kune rumwe rutivi, inozoonekwa nguva iyo kukanganisa kunoitika. (Alarm haizoonekwe chero paine inoshanda E alarm).

Heano mameseji anogona kuoneka:

  

 

 

 

 

 

 

1 = alarm
A1: Kupisa kwepamusoro alarm High t. alarm
A2: Aramu yekushisa yakaderera Low t. alarm
A4: Aramu yemusuwo Door Alarm
A5: Mashoko. Parameter o16 yapera Max Bata Nguva
A15: Aramu. Signal kubva DI1 kuisa DI1 alarm
A16: Aramu. Signal kubva DI2 kuisa DI2 alarm
A45: Chinzvimbo chekumira (yakamisa firiji kuburikidza ner12 kana DI yekuisa) (Alarm relay haizoitwa) Standby mode
A59: Nyaya yekuchenesa. Signal kubva DI1 kana DI2 kuisa Nyaya yekuchenesa
A60: Yepamusoro-tembiricha alarm yeHACCP basa HACCP alarm
Max. def nguva
E1: Mhosho mune controller EKC kukanganisa
E6: Kukanganisa mune chaiyo-nguva wachi. Tarisa bhatiri / reset wachi. –
E25: Sensor kukanganisa paS3 S3 kukanganisa
E26: Sensor kukanganisa paS4 S4 kukanganisa
E27: Sensor kukanganisa paS5 S5 kukanganisa
Pakukopa marongero kuenda kana kubva kukiyi yekukopa ine mabasa o65 kana o66, iyo inotevera ruzivo inogona kuoneka:
  • 0: Kukopa kwakapera uye OK
  • 4: Kiyi yekukopa isina kukwidzwa zvakanaka
  • 5: Kukopa kwakanga kusina kururama. Dzokorora kukopa 6: Kukopa kuEKC kwakashata. Dzokorora kukopa
  • 7: Kukopa kukiyi yekukopa kwakashata. Dzokorora kukopa
  • 8: Kukopa hakugoneki. Nhamba yekuraira kana SW vhezheni haienderane ne9: Kukanganisa kwekutaurirana uye nguva yekupera
  • 10: Kukopa kuchiri kuenderera mberi

(Ruzivo runogona kuwanikwa mu o65 kana o66 masekonzi mashoma mushure mekukopa kwatangwa).
Nzvimbo dzealarm
Kukosha kwemaaramu ega ega kunogona kutsanangurwa nekumisikidza (0, 1, 2 kana 3)
Mamiriro ekushanda (Chiyero)
Iyo controller inopinda mune mamwe mamiriro ekudzora mamiriro ayo ari kungomirira iyo inotevera poindi yemutemo. Kuita izvi "nei pasina chiri kuitika" mamiriro

zvinoonekwa, unogona kuona mamiriro ekushanda pachiratidziro. Sunda zvishoma (1s) bhatani repamusoro. Kana paine kodhi yemamiriro, icharatidzwa pachiratidziro.

Makodhi emamiriro emunhu ane zvirevo zvinotevera:

 EKC State:

(Inoratidzwa mune zvese menyu zviratidziro)
S0: Kudzora 0
S1: Kumirira kupera kweiyo yakarongeka defrost 1
S2: Kana iyo compressor iri kushanda inofanirwa kumhanya kweinenge x maminetsi. 2
S3: Kana iyo compressor yamiswa, inofanira kuramba yakamira kweinenge x maminetsi. 3
S4: Evaporator inodonha uye inomirira kuti nguva ipere 4
S10: Firiji yakamira ne main switch. Pamwe ner12 kana DI-input 10
S11: Firiji yakamiswa ne thermostat 11
S14: Defrost kutevedzana. Defrost iri kuitika 14
S15: Defrost kutevedzana. Kunonoka kweFan - mvura inonamatira kune evaporator 15
S17: Mukova wakazaruka. DI yekupinda yakavhurika 17
S20: Emergency kutonhora *) 20
S25: Manual kutonga kwezvinobuda 25
S29: Kucheneswa kwenyaya 29
S30: Kutonhodza kumanikidzirwa 30
S32: Kunonoka pane zvinobuda panguva yekutanga-up 32
S33: Kupisa basa r36 kuri kushanda 33
Zvimwe zvinoratidzwa:
kwete: Defrost tembiricha haigone kuratidzwa. Pane kumira kunoenderana nenguva
-d-: Defrost iri kuenderera mberi / Kutanga kutonhora mushure mekunyungudika
PS: Password inodiwa. Seta password

*) Emergency kutonhora kuchaita kana paine kushomeka kwechiratidzo kubva kune yakatsanangurwa S3 kana S4 sensor. Iwo mutemo unoenderera mberi neakanyoreswa avhareji cutin frequency. Pane maitiro maviri akanyoreswa - imwe yekushanda kwezuva uye imwe yekushanda kwehusiku.

Yambiro ! Kutanga kwakananga kwema compressor *
Kudzivirira compressor kuputsika parameter c01 uye c02 inofanira kuiswa maererano nevanogovera zvinodiwa kana kazhinji : Hermetic Compressors c02 min. 5 maminitsi
Semihermetic Compressors c02 min. 8 maminetsi uye c01 min. 2 kusvika 5 maminetsi (Motor kubva 5 kusvika 15 KW)
*) Yakananga activating ye solenoid mavharuvhu haidi marongero akasiyana nefekitori (0)

Operation

Display
Hukoshi hucharatidzwa nemanhamba matatu, uye nesetting unogona kuona kana tembiricha ichizoratidzwa mu °C kana mu °F.

Danfoss-AK-CC-210-Controller-For-Temperature-Control- (22)

Chiedza-emitting diodes (LED) pane yepamberi
HACCP = HACCP basa riri kushanda
Mamwe ma LED ari papanera yekumberi achavhenekera kana iyo ye-ing relay ikamiswa.

Danfoss-AK-CC-210-Controller-For-Temperature-Control- (23)

Iwo malight-emitting diode anopenya kana paine alarm.
Mune ino mamiriro iwe unogona kudhawunirodha kodhi yekukanganisa kuchiratidziro uye kudzima / kusaina alarm nekupa iyo yepamusoro knob kusundidzira kupfupi.

Defrost
Panguva ye defrost a -d- inoratidzwa muchiratidziro. Izvi view ichaenderera mberi kusvika 15 min. mushure mekunge kutonhora kwatangazve.
Zvisinei the view ye -d- ichamiswa kana:

  • Kupisa kwakakodzera mukati memaminitsi gumi nemashanu
  • Mutemo unomiswa ne "Main Switch"
  • Alarm yetembiricha yepamusoro inooneka

Mabhatani
Paunenge uchida kushandura marongero, mabhatani ekumusoro neepasi anokupa kukosha kwepamusoro kana kuderera zvichienderana nebhatani rauri kudzvanya. Asi usati wachinja kukosha, unofanirwa kuwana menyu. Iwe unowana izvi nekudzvanya bhatani repamusoro kwemasekonzi akati wandei - iwe unozoisa iyo col-umn ine parameter macode. Tsvaga iyo parameter kodhi yaunoda kuchinja uye sunda mabhatani epakati kusvika kukosha kweparameter kwaratidzwa. Paunenge wachinja kukosha, chengetedza kukosha kutsva nekudzvanya bhatani repakati.

Examples

Set menyu

  1. Batanidza bhatani repamusoro kusvika parameter r01 yaratidzwa
  2. Sunda bhatani repamusoro kana rezasi uye tsvaga iyo parameter yaunoda kuchinja
  3. Dzvanya bhatani repakati kusvika kukosha kweparameter kwaratidzwa
  4. Sunda bhatani repamusoro kana rezasi uye sarudza kukosha kutsva
  5. Dzvanya bhatani repakati zvakare kuomesa kukosha.

Cutout alarm relay / receipt alarm / ona alarm kodhi

  • Batanidza bhatani repamusoro
    Kana paine akati wandei alarm macode anowanikwa mune rolling stack. Dzvanya bhatani repamusoro-soro kana repasi kuti utarise stack inotenderera.

Seta tembiricha

  1. Batanidza bhatani repakati kusvika kukosha kwekushisa kwaratidzwa
  2. Sunda bhatani repamusoro kana rezasi uye sarudza kukosha kutsva
  3. Batanidza bhatani repakati zvakare kupedzisa kuseta.

Kuverenga tembiricha pane defrost sensor
Batanidza bhatani rezasi

Manuel anotanga kana kumisa defrost
Batanidza bhatani rezasi kwemasekonzi mana.(Kunyangwe zvisiri zvekushandisa 4).

Ona HACCP kunyoresa

  1. Ipa bhatani repakati kuti ribude kusvika h01 yaonekwa
  2. Sarudza inodiwa h01-h10
  3. Ona kukosha nekupa bhatani repakati kapfupi

Tanga zvakanaka
Nekutevera maitiro iwe unogona kutanga mutemo nekukurumidza-nekukurumidza:

  1. Vhura parameter r12 uye misa mutemo (mune itsva uye isina kumbosetwa unit, r12 ichave yatoiswa ku0 zvinoreva kumira mutemo.)
  2. Sarudza kubatanidza magetsi zvichienderana nemifananidzo iri papeji 6
  3. Vhura parameter o61 uye isa nhamba yekubatanidza yemagetsi mairi
  4. Zvino sarudza imwe yemasetirwo epamberi kubva patafura iri papeji 22.
  5. Vhura parameter o62 uye isa nhamba yezvirongwa zvepreset. Iwo mashoma akasarudzwa marongero achazoendeswa kumenyu.
  6. Vhura parameter r12 uye tanga mutemo
  7. Enda kuburikidza neongororo yezvigadziriso zvefekitori. Hukoshi mumasero egrey anoshandurwa zvinoenderana nesarudzo yako yezvirongwa. Ita chero shanduko inodiwa muzvikamu zvinoenderana.
  8. Zvenetiweki. Seta kero mu o03 wozoitumira kune gedhi / system unit ine kuseta o04.

HACCP
Iri basa rinotevera tembiricha yemudziyo uye kuridza alarm kana yakatarwa tembiricha yadarika. Iyo alarm ichauya kana nguva yekunonoka yapera.
Kana tembiricha yadarika kukosha kwemuganho inoramba ichinyoreswa uye kukosha kwepamusoro kuchachengetwa kusvika pakazodzokororwa. Kuchengetwa pamwe chete nekukosha kuchava nguva uye nguva yekushisa kudarika.

Exampkupisa kwakanyanya kudarika:

Kupfuura panguva yemutemo wakajairika

 

Danfoss-AK-CC-210-Controller-For-Temperature-Control- (24)

Kupfuura maererano nekukundikana kwemagetsi uko mutongi anogona kuramba achinyora nguva yekuita.

Danfoss-AK-CC-210-Controller-For-Temperature-Control- (25)

Kupfuura maererano nekutadza kwemagetsi kana controller yarasikirwa newachi yayo uye nekudaro kuita kwayo nguva.

Danfoss-AK-CC-210-Controller-For-Temperature-Control- (26)

Kuverenga kweakasiyana siyana muHACCP basa kunogona kuitika nekudzvanya kwenguva refu pabhatani repakati.
Zvidzidzo izvi, sezvinotevera:

  • h01: Tembiricha
  • h02: Kuverenga kwechimiro chemutongi kana tembiricha yadarika:
    • H1 = mutemo wakajairika.
    • H2 = kukundikana kwesimba. Nguva dzakachengetwa.
    • H3 = kukundikana kwesimba. Nguva hadzina kuchengetwa.
    • h03: nguva. Gore
    • h04: nguva. Mwedzi
    • h05: Nguva: Zuva
    • h06: nguva. Awa
    • h07: nguva. Mineti
    • h08: Nguva mumaawa
    • h09: Nguva mumaminitsi
    • h10: Iyo yakanyoreswa tembiricha yepamusoro
      (Kugadzika kwebasa kunoitika sezvakangoita mamwe maseti. Ona ongororo yemenyu papeji rinotevera).

Ongororo yemenyu

Parameters EL-dhayagiramu nhamba (peji 6) Min.-

value

 Max.-

value

 Factory

setting

 Actual

setting
Function Codes 1 2 3 4 5 6 7 8 9 10
Normal kushanda
Tembiricha (set point) — -50.0°C 50.0°C 2.0°C
Thermostat
Differential *** r01 0.1 K 20.0K 2.0 K
Max. muganhu we setpoint setting *** r02 -49.0°C 50°C 50.0°C
Min. muganhu we setpoint setting *** r03 -50.0°C 49.0°C -50.0°C
Kugadziriswa kwechiratidzo chekushisa r04 -20.0 K 20.0 K 0.0 K
Tembiricha unit (°C/°F) r05 °C °F °C
Kugadziriswa kwechiratidzo kubva kuS4 r09 -10.0 K +10.0 K 0.0 K
Kugadziriswa kwechiratidzo kubva kuS3 r10 -10.0 K +10.0 K 0.0 K
Sevhisi yemaoko, kumisa mutemo, kutanga mutemo (-1, 0, 1) r12 -1 1 0
Displacement yereferensi panguva yekushanda kwehusiku r13 -10.0 K 10.0 K 0.0 K
Tsanangudzo uye uremu, kana zvichibvira, zvema sensors e thermostat

– S4% (100%=S4, 0%=S3)

 r15 0% 100% 100%
Iyo yekudziya basa inotangwa akati wandei madhigirii pazasi

thermostats cutout tembiricha

 r36 -15.0 K -3.0 K -15.0 K
Activation of reference displacement r40 r39 DZIMA ON DZIMA
Kukosha kwereferensi yekutamisa (activate kuburikidza neR39 kana DI) r40 -50.0 K 50.0 K 0.0 K
Alarm
Kunonoka kwearamu yekushisa A03 0 min 240 min 30 min
Kunonoka kuridza alarm *** A04 0 min 240 min 60 min
Kunonoka kwearamu yekushisa mushure mekudzikisa A12 0 min 240 min 90 min
High alarm limit *** A13 -50.0°C 50.0°C 8.0°C
Low alarm limit *** A14 -50.0°C 50.0°C -30.0°C
Alarm inonoke DI1 A27 0 min 240 min 30 min
Alarm inonoke DI2 A28 0 min 240 min 30 min
Chiratidzo chealarm thermostat. S4% (100%=S4, 0%=S3) A36 0% 100% 100%
Compressor
Min. Nenguva c01 0 min 30 min 0 min
Min. OFF-nguva c02 0 min 30 min 0 min
Nguva inononoka ye cutin of comp.2 c05 0 sec 999 sec 0 sec
Compressor relay 1 inofanira kucheka uye kubuda inversely

(NC-basa)

 c30 0

DZIMA

 1

ON

 0

DZIMA
Defrost
Defrost nzira (hapana/EL/GAS/BRINE) d01 Aihwa bri EL
Defrost stop tembiricha d02 0.0°C 25.0°C 6.0°C
Kupindirana pakati pe defrost kunotanga d03 0 maawa 240

maawa

 8 maawa
Max. defrost duration d04 0 min 180 min 45 min
Displacement yenguva pane cutin ye defrost pakutanga-up d05 0 min 240 min 0 min
Kutora nguva d06 0 min 60 min 0 min
Kunonoka kwe fan kunotanga mushure mekudzima d07 0 min 60 min 0 min
Fani inotanga tembiricha d08 -15.0°C 0.0°C -5.0°C
Fan cutin panguva ye defrost

0: Yakamira

1: Kumhanya

2: Kumhanya panguva yepombi pasi uye defrost

 d09 0 2 1
Defrost sensor (0=nguva, 1=S5, 2=S4) d10 0 2 0
Pombi pasi kunonoka d16 0 min 60 min 0 min
Kunonoka kwemvura d17 0 min 60 min 0 min
Max. aggregate firiji nguva pakati pema defrosts maviri d18 0 maawa 48 maawa 0 maawa
Defrost pakudiwa - S5 tembiricha inotenderwa kusiyanisa panguva-

kuwedzera kwechando. Pachirimwa chepakati sarudza 20 K (= kure)

 d19 0.0 K 20.0 k 20.0 K
Kunonoka kwekupisa gasi defrost d23 0 min 60 min 0 min
Fan
Fani inomira pa cutout compressor F01 Aihwa Ehe Aihwa
Kunonoka kwe fan kumira F02 0 min 30 min 0 min
Tembiricha yekumisa fan (S5) F04 -50.0°C 50.0°C 50.0°C
HACCP
Chaiyo tembiricha kuyerwa kweiyo HACCP basa h01
Tembiricha yekupedzisira yakanyoreswa h10
Kusarudzwa kwebasa uye sensor yeHACCP basa. 0 = kwete

HACCP basa. 1 = S4 yakashandiswa (pamwe zvakare S3). 2 = S5 yakashandiswa

 h11 0 2 0
Alarm muganho weiyo HACCP basa h12 -50.0°C 50.0°C 8.0°C
Nguva inononoka yeHACCP alarm h13 0 min. 240 min. 30 min.
Sarudza chiratidzo cheiyo HACCP basa. S4% (100% = S4, 0% = S3) h14 0% 100% 100%
Yechokwadi nguva wachi
Nguva nhanhatu dzekutanga dze defrost. Kugadzwa kwemaawa.

0 = YAKADZWA

 t01-t06 0 maawa 23 maawa 0 maawa
Nguva nhanhatu dzekutanga dze defrost. Kugadzwa kwemaminetsi.

0 = YAKADZWA

 t11-t16 0 min 59 min 0 min
Clock - Kuronga maawa *** t07 0 maawa 23 maawa 0 maawa
Clock - Kugadzika kweminiti *** t08 0 min 59 min 0 min
Clock - Kuronga zuva *** t45 1 31 1
Wachi - Kugadzika kwemwedzi *** t46 1 12 1
Wachi - Kugadzika kwegore *** t47 0 99 0
Miscellaneous
Kunonoka kwekubuda kwezviratidzo mushure mekupera simba o01 0 p 600 p 5 p
1 2 3 4 5 6 7 8 9 10
Nyora chiratidzo paDI1. Basa:

0=isina kushandiswa. 1=chimiro paDI1. 2=basa regonhi rine alarm kana rakavhurika. 3= alarm yedoor kana yakavhurwa. 4=defrost kutanga (pulse-signal). 5=ext.main switch. 6=kushanda kwehusiku 7=chinja chirevo (activate r40). 8=alarm function kana yakavharwa. 9=alarm function kana yakavhurwa. 10=kucheneswa kwekesi (pulse signal). 11=kumanikidzira kutonhodza pagasi rinopisa.

 o02 1 11 0
Network address o03 0 240 0
On/Off switch (Service Pin message)

ZVINOKOSHA! o61 anofanira kuiswa pamberi peo04

 o04 DZIMA ON DZIMA
Kupinda kodhi 1 (ese magadzirirwo) o05 0 100 0
Yakashandiswa sensor mhando (Pt / PTC/NTC) o06 Pt ntc Pt
Ratidza nhanho = 0.5 (yakajairika 0.1 paPt sensor) o15 Aihwa Ehe Aihwa
Max kubata nguva mushure mekubatanidza defrost o16 0 min 60 min 20
Sarudza chiratidzo chekuratidzira view. S4% (100%=S4, 0%=S3) o17 0% 100% 100%
Nyora chiratidzo paDI2. Basa:

(0=haina kushandiswa. 1=status paDI2. 2=basa remusuwo nearamu kana rakavhurika. 3=alarm yegonhi kana yakavhurika. 4=defrost start (pulse-signal). 5=ext. main switch 6=night operation 7=change reference (activate r40). 8=alarm function kana yakavharwa. 9=alarm function when open. 10=t pulse cleaning (11= pulse cleaning). gasi defrost.). 12 = yakabatana defrost)

 o37 0 12 0
Kugadziriswa kwebasa rechiedza (relay 4)

1=ON panguva yekushanda kwezuva. 2= ​​ON / DZIMA kuburikidza nedata communication. 3 = ON inotevera DI-basa, kana DI yasarudzwa kune basa remusuwo kana kumusuwo alarm

 o38 1 3 1
Kuitwa kwechiedza relay (chete kana o38=2) o39 DZIMA ON DZIMA
Kupisa kwenjanji Panguva panguva yekushanda kwezuva o41 0% 100% 100
Kupisa kwenjanji Panguva panguva yekushanda kwehusiku o42 0% 100% 100
Nguva yekupisa njanji (Panguva + Nguva yekusashanda) o43 6 min 60 min 10 min
Nyaya yekuchenesa. 0=hapana kuchenesa kesi. 1=Mafeni chete. 2=Zvose zvabuda

Off.

 *** o46 0 2 0
Kusarudzwa kwe EL diagram. Ona pamusoroview peji 6 * o61 1 10 1
Dhaunirodha seti yezvirongwa zvakafanotemerwa. Ona pamusoroview inotevera

peji.

 * o62 0 6 0
Kupinda kodhi 2 (chikamu kuwana) *** o64 0 100 0
Sevha zvigadziriso zviripo kune kiyi yekuronga.

Sarudza nhamba yako.

 o65 0 25 0
Rodha seti yezvigadziriso kubva kukiyi yepurogiramu (kare

yakachengetedzwa kuburikidza neo65 basa)

 o66 0 25 0
Tsiva marongero efekitori yevatongi neazvino set-

tings

 o67 DZIMA On DZIMA
Service
Status codes inoratidzwa papeji 17 S0-S33
Tembiricha yakayerwa neS5 sensor *** u09
Status pane DI1 kuisa. pa/1=yakavharwa u10
Tembiricha yakayerwa neS3 sensor *** u12
Mamiriro ekushanda kwehusiku (kubatidzwa kana kudzima) 1=yakavharwa *** u13
Tembiricha yakayerwa neS4 sensor *** u16
Thermostat tembiricha u17
Verenga ikozvino regulation reference u28
Status pane DI2 inobuda. pa/1=yakavharwa u37
Tembiricha inoratidzwa pachiratidziro u56
Yakayerwa tembiricha yealarm thermostat u57
Status pane relay yekutonhodza ** u58
Status pane relay ye fan ** u59
Status pane relay ye defrost ** u60
Status pane relay yerailheat ** u61
Status pane relay yealarm ** u62
Chimiro pane relay yechiedza ** u63
Chimiro pane relay yevharuvhu mumutsetse wekusveta ** u64
Chimiro pane relay ye compressor 2 ** u67

*) Inogona kuiswa chete kana mutemo wamiswa (r12=0)
**) Inogona kudzorwa nemaoko, asi chete kana r12=-1
***) Nekusvika kodhi 2 kuwana kune aya menyu kuchave kushoma

Kuiswa kwefekitari
Kana iwe uchida kudzoka kune fekitori-set kukosha, inogona kuitwa neiyi nzira:

  • Cheka voltage kune controller
  • Chengetedza mabhatani ese ari maviri akaora mwoyo panguva imwe chete apo iwe uchidzokorora nect iyo yekugovera voltage
Tafura yekubatsira yezvigadziriso (nekukurumidza-seta) Nyaya Room
Defrost kumira nenguva Defrost kumira paS5 Defrost kumira nenguva Defrost kumira paS5
Preset marongero (o62) 1 2 3 4 5 6
Tembiricha (SP) 4°C 2°C -24°C 6°C 3°C -22°C
Max. temp. kuisa (r02) 6°C 4°C -22°C 8°C 5°C -20°C
Min. temp. kuisa (r03) 2°C 0°C -26°C 4°C 1°C -24°C
Sensor chiratidzo che thermostat. S4% (r15) 100% 0%
Alarm limit yakakwira (A13) 10°C 8°C -15°C 10°C 8°C -15°C
Alarm limit yadzikira (A14) -5°C -5°C -30°C 0°C 0°C -30°C
Sensor chiratidzo chearamu inoshanda.S4% (A36) 100% 0%
Nguva pakati pe defrost (d03) 6 h 6h 12h 8h 8h 12h
Defrost sensor: 0=nguva, 1=S5, 2=S4 (d10) 0 1 1 0 1 1
DI1 config. (o02) Kucheneswa kwenyaya (=10) Basa remusuwo (=3)
Sensor chiratidzo chekuratidzira view S4% (017) 100% 0%

Override
Iyo controller ine akati wandei mabasa anogona kushandiswa-pamwe chete neanopfuura basa mune master gedhi / System Manager.

 

Basa kuburikidza nedata communication

  

Zvishandiso zvinofanirwa kushandiswa mumasuwo override function

  

Inoshandiswa parameter muAK-CC 210
Kutanga kwe defrosting Defrost control Nguva yakatarwa – – – Def.start
 

Coordinated defrost

  

Defrost control

  

– – – HoldAfterDef u60 Def.relay
 

Husiku kudzoka

  

Zuva/husiku kudzora Nguva yakatarwa

  

– – – Night setbck
Chiedza chekudzora Zuva/husiku kudzora Nguva yakatarwa o39 Chiedza Remote

Kuraira

Danfoss-AK-CC-210-Controller-For-Temperature-Control- (27)

Connections

Danfoss-AK-CC-210-Controller-For-Temperature-Control- (28)

Magetsi
230 V ac

Sensors
S3 uye S4 ndiwo ma sensors e thermostat.
Kuseta kunotara kuti S3 kana S4 kana ese ari maviri achashandiswa.
S5 is a defrost sensor uye inoshandiswa kana defrost ichifanira kumira zvichienderana nekupisa.

Digital On/Off masaini
Iyo yekucheka-mukati inopinza ichamutsa basa. Izvo zvinogoneka mabasa zvinotsanangurwa mumamenyu o02 uye o37.

Kuratidzwa kwekunze
Kubatana kwemhando yekuratidzira EKA 163A (EKA 164A).

Relays
Kushandiswa kwese kunotaurwa pano. Onawo peji 6 panoratidzwa maitiro akasiyana.

  • DO1: Firiji. Iyo relay inocheka mukati kana controller ichikumbira firiji
  • DO2: Defrost. Iyo relay ichacheka mukati kana defrost iri kuitika
  • DO3: Kune mafeni kana firiji 2
    Mafeni: Iyo relay ichacheka mukati kana mafeni achifanira kushanda Firiji 2: Iyo relay ichacheka mukati kana firiji nhanho yechipiri inofanirwa kutemwa mukati.
  • DO4: Kune aramu, kupisa kwenjanji, mwenje kana hotgas defrost Alamu: Cf. diagram. Iyo relay inochekwa mukati panguva yakajairika opera-tion uye inocheka kunze mune alarm mamiriro uye kana controller afa (de-energized)
    Kupisa kwenjanji: Iyo relay inocheka mukati kana kupisa kwenjanji kuchizoshanda
    Chiedza: Iyo relay inocheka mukati kana mwenje uchifanira kubatidzwa paHotgas defrost: Ona dhizaini. Iyo relay ichacheka kana defrost ichifanira kuitwa

Kukurukurirana kwemashoko
Iyo controller inowanikwa mune akati wandei shanduro uko data com-munication inogona kuitwa neimwe yeanotevera masisitimu: MOD-bhazi kana LON-RS485.
Kana kutaurirana kwedata kuchishandiswa, zvakakosha kuti kuiswa kwetambo yekutaurirana data kuitwe nemazvo.
Ona zvinyorwa zvakasiyana Nha. RC8AC...

Mheremhere yemagetsi
Matambo emasensa, DI ekuisa uye kutaurirana kwedata kunofanirwa kuchengetedzwa kwakaparadzaniswa kubva kune mamwe tambo dzemagetsi:

  • Shandisa matireyi etambo akasiyana
  • Chengeta chinhambwe pakati petambo dzinenge 10 cm
  • Tambo refu paDI inopinza inofanirwa kudzivirirwa

Coordinated defrost kuburikidza netambo dzekubatanidza

Danfoss-AK-CC-210-Controller-For-Temperature-Control- (29)

Aya anotevera controller anogona kubatanidzwa kumusoro nenzira iyi:

  • AK-CC 210, AK-CC 250, AK-CC 450,
    AK-CC 550
  • Max. 10.

Firiji inotangwazve kana vatongi vese "vakaburitsa" chiratidzo chekudzikisa.

Coordinated defrost kuburikidza nedata communication

Danfoss-AK-CC-210-Controller-For-Temperature-Control- (30)

Data

Mugove voltage 230 V ac +10/-15 %. 2.5 VA, 50/60 Hz
Sensors 3 pcs kure kana Pt 1000 kana

PTC 1000 kana

NTC-M2020 (5000 ohm / 25°C)
 

 

 

Kururama

 Kuyera chiyero -60 kusvika +99°C
 

Controller

 ±1 K pazasi -35°C

± 0.5 K pakati -35 kusvika +25°C

±1 K pamusoro +25°C
Pt 1000 sensor ±0.3 K pa 0°C

± 0.005 K pagiredhi
Display LED, 3-manhamba
Kuratidzwa kwekunze EKA 163A
 

Digital inputs

 Signal kubva kumabasa ekusangana Zvinodiwa kune vanobatika: Goridhe yekuisa Cable kureba kunofanirwa kunge kuri max. 15 m

Shandisa ebetsero relay kana tambo yakareba
Magetsi ekubatanidza tambo Max.1,5 mm2 multi-core cable
 

 

 

 

 

 

 

Relays*

 CE

(250 V ac)

 UL *** (240 V ac)
DO1.

Firiji

 8 (6) A 10 A Resistive 5FLA, 30LRA
DO2. Defrost 8 (6) A 10 A Resistive 5FLA, 30LRA
 

DO3. Fan

  

6 (3) A

 6 A Resistive 3FLA, 18LRA

131 VA Mutyairi

basa
 

DO4. Alarm

 4 (1) A

Min. 100 mA**

 4 Anoramba

131 VA Pilot basa
 

 

Environments

 0 kusvika +55 ° C, Panguva yekushanda

-40 kusvika +70 ° C, Panguva yekufambisa
20 - 80% Rh, kwete condensed
Hapana kuvhundutsa simba / vibrations
Density IP65 kubva mberi.

Mabhatani uye kurongedza zvakamisikidzwa kumberi.
Escapement reserve yewachi  

4 maawa
Zvibvumirano

Danfoss-AK-CC-210-Controller-For-Temperature-Control- (32)

 EU Low Voltage Directive uye EMC inoda kuti kucherechedzwa kweEC kuteedzerwe

LVD yakaedzwa acc. EN 60730-1 uye EN 60730-2-9, A1, A2

EMC yakaedzwa acc. EN61000-6-3 uye EN 61000-6-2

Danfoss-AK-CC-210-Controller-For-Temperature-Control- (31)

  • * DO1 uye DO2 vane gumi nematanhatu A relay. Iyo yataurwa 16 A inogona kuwedzerwa kusvika ku8 A, kana ambient tembiricha inochengetwa iri pasi pe10°C. DO50 uye DO3 vane 4 A relay. Max. mutoro unofanira kuchengetedzwa.
  • ** Kuiswa kwegoridhe kunovimbisa kuita basa nematoro madiki ekusangana
  • *** UL-mvumo yakavakirwa pa30000 couplings.

Danfoss haigamuchire mutoro wezvikanganiso zvinogona kuitika mumakatalog, mabhurocha uye zvimwe zvakadhindwa. Danfoss inochengetedza kodzero yekushandura zvigadzirwa zvayo pasina chiziviso. Izvi zvinoshandawo kune zvigadzirwa zvagara zvakarongeka zvakapa kuti shanduko dzakadaro dzinogona kuitwa pasina shanduko dzinotevera dziri kudikanwa mune zvakatemerwa kare.
Ese maratidziro mune ino chinyorwa zvinhu zvemakambani anotarisisa. Danfoss uye Danfoss logotype zviratidzo zveDanfoss A/S. Kodzero dzese dzakachengetwa.

User Guide RS8EP602 © Danfoss 2018-11

FAQ

  • Mubvunzo: Mangani ma sensors ethermostat anogona kubatanidzwa kune AK-CC 210 controller?
    A: Kusvika maviri ethermostat sensors anogona kubatana.
  • Mubvunzo: Ndeapi mabasa anogona kushandiswa nedhijitari?
    A: Iwo edhijitari ekuisa anogona kushandiswa kuchenesa kesi, kubatwa kwegonhi nealarm, kutanga kutenderera kwe defrost, yakarongeka defrost, shanduko-pamusoro pakati pemareferensi maviri etembiricha, uye kuendesazve kwenzvimbo yekubatana kuburikidza nedata kutaurirana.

Zvinyorwa / Zvishandiso

Danfoss AK-CC 210 Controller Yekudzora Tembiricha [pdf] Bhuku reMushandisi
AK-CC 210 Controller Yekudzora Temperature, AK-CC 210, Controller Yekudzora Tembiricha, Yekudzora Tembiricha, Kudzora Kudzora.

References

Related Posts

Siya mhinduro

Yako email kero haizoburitswa. Nzvimbo dzinodiwa dzakamakwa *