NXP FRDM-IMX93 Atina'e Komiti Fa'aaogā Tusi Taiala

Ia mautinoa o loʻo ola le laupapa ma faʻaogaina.
Mulimuli i faʻatonuga faʻatulagaina o loʻo tuʻuina atu i le tagata faʻaoga
tusi lesona mo faʻamatalaga auiliili.

2. Meafaigaluega Meafaigaluega I Lugaview:

O le laupapa FRDM-IMX93 o loʻo faʻaalia ai le tele o fesoʻotaʻiga ma
vaega, e aofia ai le USB C fesoʻotaʻiga, DRAM manatua, tele teuina
filifiliga, mea pueata ma fa'aaliga feso'ota'iga, feso'ota'iga Ethernet, ma
eseese I/O expanders. Fa'amasani oe ile fa'atulagaina o le laupapa
ma vaega a'o le'i fa'aogaina.

3. Fa'aoga Taiala:

O le taimi lava e fa'atulaga ai le laupapa ma fa'aola, e mafai ona e amata su'esu'e
le gafatia o le i.MX 93 processor e ala i le tamoe sample
talosaga po'o le atina'eina o au lava galuega. Vaai i le mea ua saunia
fa'amaumauga mo ta'iala polokalame ma examples.

Fesili e Fai soo (FAQ):

Q: O a uiga autu o le laupapa FRDM-IMX93?

A: O mea autu e aofia ai le lua Arm Cortex-A55 + Arm
Cortex-M33 core processor, fesoʻotaʻiga USB, DRAM manatua, masini
filifiliga teuina, mea pueata ma faʻaaliga faʻafesoʻotaʻi, Ethernet
feso'ota'iga, ma fa'alautele I/O eseese mo le fa'aleleia
galuega faatino.

Q: E mafai faapefea ona ou faʻafesoʻotaʻi peripherals i le laupapa FRDM-IMX93?

A: E mafai ona e faʻafesoʻotaʻi peripherals e ala i fesoʻotaʻiga avanoa
e pei o ports USB, HDMI mo faʻaaliga, Ethernet mo networking, ma
eseese I/O expanders mo galuega faaopoopo. Fa'asino i le
tusi fa'aoga mo fa'atonuga feso'ota'iga fa'apitoa.

“`

View Fullscreen

UM12181
FRDM-IMX93 Board Tusi Taiala
Rev. 1.0 — 9 Tesema 2024

Fa'aoga tusi lesona

Fa'amatalaga pepa

Fa'amatalaga

Anotusi

upu autu

i.MX 93, FRDM-IMX93, UM12181

Avanoa

O le FRDM i.MX 93 development board (FRDM-IMX93 board) o se faʻavae taugofie ua fuafuaina e faʻaalia ai foliga sili ona faʻaaogaina o le i.MX 93 talosaga faʻapipiʻi i totonu o se pusa laʻititi ma taugofie.

NXP Semiconductors

UM12181
FRDM-IMX93 Board Tusi Taiala

USB C SOSO'OGA

1 FRDM-IMX93 sili atuview

O le FRDM i.MX 93 development board (FRDM-IMX93 board) o se faʻavae taugofie ua fuafuaina e faʻaalia ai foliga sili ona faʻaaogaina o le i.MX 93 Applications Processor i totonu o se pusa laʻititi ma taugofie. O le FRDMIMX93 laupapa o se faʻalapotopotoga faʻapipiʻi tulaga ulufale, lea e fesoasoani i le au atinaʻe ia masani i le gaosiga aʻo leʻi faʻatupeina le tele o punaoa i ni mamanu faʻapitoa.
O lenei pepa o lo'o aofia ai le fa'atulagaina o faiga ma fa'aputuga, ma tu'uina atu fa'amatalaga au'ili'ili i le aotelega o le mamanu ma le fa'aogaina o le laupapa FRDM mai se va'aiga o masini komepiuta.

1.1 poloka ata
Ata 1 o loʻo faʻaalia ai le poloka poloka FRDM-IMX93.

MIPI DSI x4 laina

LVDS ile HDMI

USB C PD

SYS PWR

PMIC NXP PCA9451

MIPI DSI PWR

DRAM LPDDR4/X: 2 GB < x16 b >

x16 bits DRAM

LVDS TX SD3
UART5/SAI1
USB2

MAYA-W2 WIFI/BT/802.15.4 SW
M.2 NGFF KEY-E:WiFi/BT…
# NXP Wi-Fi/BT 1×1 WiFi 6 (802.11ax)

SW USB 2.0 DRP

USB 2.0 USB ITIGA-A

eMMC 5.1 32 GB HS400
Meapueata x1 MIPI CSI

x8 SDHC SD1
x2 LANE MIPI CSI

i.MX93
LIMA: x2 CORTEX-A55 (1.8 GHz) x1 CORTEX-M33 (250 MHz)
ML: 0.5 TOPs Ethos-U65 NPU (1 GHz)

USB 2.0 DRP USB1

USB 2.0 USB ITIGA-C

RGMII

Gigabit NET

x2 ENET

YT8521SH-CA

# AVB, 1588, ma le IEEE 802.3az

CANFD

E MAFAI NXP TJA1051T/3

HDR

M.2
RJ45

USB C

ADC: HDR CN

ADC x12 bit
RGB-LED PUTTON

ADC PWM GPIO

UART PDM

UART i le USB

CORTEX0-A55/CORTEX-M33 debug Lagolago mamao debug

MQS

OU laina i fafo

I2C SAI3 I2C

RTC

SENSOR

SD2 MicroSD
SD3.0 MicroSD
Ata 1.FRDM-IMX93 poloka poloka

SWD

I2C/SPI/UART…

SWD DEBUG
HDR

EXP CN UART/I2C/SPI.. # Audio HAT/RFID/PDM...
HDR

1.2 Fa'aaliga a le Komiti Fa'atonu
Lisi 1 o loʻo lisiina ai foliga o le FRDM-IMX93.

UM12181
Fa'aoga tusi lesona

O fa'amatalaga uma o lo'o tu'uina atu i totonu o lenei pepa e fa'atatau i fa'aletulafono fa'aletulafono.
Rev. 1.0 — 9 Tesema 2024

NXP Semiconductors

UM12181
FRDM-IMX93 Board Tusi Taiala

Laulau 1. FRDM-IMX93 foliga

Vaega o le Komiti

O lo'o fa'aogaina le fa'aogaina o le fa'aogaina

Fa'amatalaga

Fa'atonuga talosaga

O le i.MX 93 applications processor o loʻo faʻaalia ai le lua Arm Cortex-A55 + Arm Cortex-M33 autu e oʻo atu i le 1.7 GHz, o le neural processing unit (NPU) o le 0.5 TOPS Faʻamatalaga: Mo nisi faʻamatalaga i le i.MX 93 processor, tagaʻi i le i.MX 93 Applications Processor Reference Manual.

fa'aoga USB

USB 2.0 maualuga-saoasaoa talimalo ma · x1 USB 2.0 Ituaiga C connector

pulea masini

· x1 USB 2.0 Ituaiga A so'oga

DRAM manatua DRAM pule ma PHY 2 GB LPDDR4X (Micron MT53E1G16D1FW-046 AAT:A)

Teuga tele

uSDHC

· 32 GB eMMC5.1 (FEMDRM032G-A3A55) · MicroSD card connector (SD3.0 lagolago)

Fa'atonuga fa'avae

· Fa'aliga ta'avale ta'avale e tasi le ta'avale mai le masini eMMC · E lagolagoina fo'i e le Komiti Fa'atonu le ta'aloga SD card

Ata pu'eata MIPI CSI

Tasi le CSI (x2 data lane), feso'ota'iga uaea FPC (P6)

Fa'aali fa'aaliga MIPI DSI

x4 laina fa'amatalaga MIPI DSI, feso'ota'iga uaea FPC (P7)

HDMI

x4 laina fa'amatalaga LVDS i le HDMI converter chip (IT6263) feso'ota'i ile feso'ota'iga HDMI, P5

feso'ota'iga Ethernet Lua fa'atonu ENET

· 10/100/1000 Mbit/s RGMII Ethernet fa'atasi ai ma le tasi RJ45 feso'ota'iga ma le TSN lagolago (P3) feso'ota'i ma PHY fafo, YT8521
· 10/100/1000 Mbit/s RGMII Ethernet ma le tasi RJ45 so'oga (P4) feso'ota'i ma PHY fafo, YT8521

I/O fa'alautele

CAN, I2C/I3C, su'esu'e fa'aigoa-todigital (ADC)

E tasi le 10-pin 2×5 2.54 mm so'oga P12 e maua ai: · Tasi le saosaoa maualuga CAN transceiver TJA1051GT/3 feso'ota'iga · Ulutala 3-pin mo le fa'alauteleina o le I2C/I3C · Lagolago ADC e lua-ala.

O luga ole Wi-Fi SDIO, UART, SPI, SAI

I luga o le Wi-Fi 6 / Bluetooth 5.4 module

Wi-Fi/Bluetooth fa'aoga

USB, SDIO, SAI, UART, I2C, ma GPIO

Tasi le M.2/NGFF Key E mini card 75-pin connector, P8, USB supporting, SDIO, SAI, UART, I2C, and Vendor-defined SPI interfaces Fa'amatalaga: I le faaletonu, o nei faailo e fesoʻotaʻi ma le onboard Wi-Fi module, peitaʻi, e faʻaaoga lenei M.2 slot, e tatau ona e toe faʻaaogaina resistors (silasila i le Laulau 15).

Leo

MQS

MQS lagolago

Debug fa'aoga

· USB-i-UART masini, CH342F · E tasi le USB 2.0 Type-C connector (P16) o le CH342F e maua ai le lua COM
taulaga:
O le muamua COM port e fa'aoga mo Cortex A55 system debug O le lona lua COM port e fa'aoga mo Cortex M33 system debug · Serial Wire Debug (SWD), P14

Fa'alautele uafu

Tasi 40-pin ulu-lauipu pine mo le I2S, UART, I2C, ma le GPIO fa'alautele

Malosiaga

· Tasi le feso'ota'iga USB 2.0 Type-C mo na'o le tu'uina atu o le mana · PCA9451AHNY PMIC · Tu'ufa'atasi DCDC/LDO

PCB

FRDM-IMX93: 105 mm × 65 mm, 10-vaega

UM12181
Fa'aoga tusi lesona

O fa'amatalaga uma o lo'o tu'uina atu i totonu o lenei pepa e fa'atatau i fa'aletulafono fa'aletulafono.
Rev. 1.0 — 9 Tesema 2024

NXP Semiconductors

Laulau 1. FRDM-IMX93 fa'aaliga…fa'aauau

Vaega o le Komiti

O lo'o fa'aogaina le fa'aogaina o le fa'aogaina

Numera vaega e mafai ona oka

Fa'amatalaga FRDM-IMX93

1.3 Mea e aofia i le pusa laupapa
Laulau 2 o lo'o lisiina ai mea o lo'o aofia i le pusa laupapa FRDM-IMX93.
Laulau 2. Pusa o le laupapa fa'amatalaga mea fa'amatalaga FRDM-IMX93 laupapa USB 2.0 Type-C Male i Type-A Male fa'apotopotoga cable FRDM-IMX93 Ta'iala Fa'anatinati

1.4 Ata laupapa
Ata 2 o lo'o fa'aalia ai le pito i luga view o le laupapa FRDM-IMX93.

UM12181
FRDM-IMX93 Board Tusi Taiala
Aofaiga 1 2 1

Ata 2.FRDM-IMX93 pito i luga view Ata 3 o loʻo faʻaalia ai fesoʻotaʻiga o loʻo avanoa ile pito i luga ole laupapa FRDM-IMX93.

UM12181
Fa'aoga tusi lesona

O fa'amatalaga uma o lo'o tu'uina atu i totonu o lenei pepa e fa'atatau i fa'aletulafono fa'aletulafono.
Rev. 1.0 — 9 Tesema 2024

NXP Semiconductors
GbE RJ45 (P4, P3)

UM12181
FRDM-IMX93 Board Tusi Taiala

RTC PWR (P18)

USB Ituaiga A (P17)
Toe setiina (P19)

HDMI (P5)

MQS (P15)

USB Ituaiga C (P2)

NXP fa'aoga masani (P12)
SWD (P14)

USB Ituaiga C USB Ituaiga C

PWR fa'aoga

DBG

(P1)[1]

(P16)

MIPI-CSI (P6)
MIPI-DSI (P7)

FA'ATA'IGA (P11)

[1] - USB Type C PWR input (P1) o loʻo faʻaalia i le ata e naʻo le pau lea o le pusa eletise, ma e tatau ona tuʻuina atu mo le faʻaogaina o le polokalama.

Ata 3. FRDM-IMX93 fesoʻotaʻiga

Ata 4 o loʻo faʻaalia ai ki luga o le laupapa, faʻamau, ma LED o loʻo maua i luga o le laupapa FRDM-IMX93.

UM12181
Fa'aoga tusi lesona

O fa'amatalaga uma o lo'o tu'uina atu i totonu o lenei pepa e fa'atatau i fa'aletulafono fa'aletulafono.
Rev. 1.0 — 9 Tesema 2024

NXP Semiconductors

UM12181
FRDM-IMX93 Board Tusi Taiala

Su'e fa'atutu (SW1)

SW3 D614 D613

SW4

RGB LED (LED1) PWR
K1

Ata 4.FRDM-IMX93 i luga ole laupapa ki, faamau, ma LED

O le ata 5 o loʻo faʻaalia ai le pito i lalo view, ma faʻamaonia ai foʻi fesoʻotaʻiga o loʻo maua i le pito i lalo ole laupapa FRDM-IMX93.

UM12181
Fa'aoga tusi lesona

O fa'amatalaga uma o lo'o tu'uina atu i totonu o lenei pepa e fa'atatau i fa'aletulafono fa'aletulafono.
Rev. 1.0 — 9 Tesema 2024

NXP Semiconductors

UM12181
FRDM-IMX93 Board Tusi Taiala

Ata 5.FRDM-IMX93 pito i lalo view

M.2 Ki E (P8)

MicroSD (P13)

1.5 Feso'ota'i

Va'ai le Ata 3 ma le Ata 5 mo so'oga tulaga i luga o le laupapa. Laulau 3 o loʻo faʻamatalaina ai fesoʻotaʻiga laupapa FRDM-IMX93.

Laulau 3. FRDM-IMX93 feso'ota'iga Vaega fa'ailoaina Ituaiga Feso'ota'i

P1, P2, P16 USB 2.0 Ituaiga C

P3, P4

RJ45 jack

HDMI A so'oga

22-pin FPC so'oga

P9 (DNP)

U.FL so'oga

P10 (DNP)

U.FL so'oga

75-pine so'oga

P11

2×20-pine so'oga

P12

2×5-pine so'oga

Fa'amatalaga Feso'ota'iga USB Feso'ota'i Ethernet feso'ota'iga HDMI MIPI CSI FPC feso'ota'iga MIPI DSI FPC feso'ota'iga RF antenna so'oga feso'ota'iga RF M.2 socket KEY-E GPIO fa'alauteleina I/O so'oga

Vaega Faasino Vaega 2.19.2 Vaega 2.17 Vaega 2.16 Vaega 2.14 Vaega 2.15 Vaega 2.11 Vaega 2.11 Vaega 2.10 Vaega 2.18 Vaega 2.4

UM12181
Fa'aoga tusi lesona

O fa'amatalaga uma o lo'o tu'uina atu i totonu o lenei pepa e fa'atatau i fa'aletulafono fa'aletulafono.
Rev. 1.0 — 9 Tesema 2024

NXP Semiconductors

UM12181
FRDM-IMX93 Board Tusi Taiala

Laulau 3. FRDM-IMX93 feso'ota'iga...fa'aauau Vaega fa'ailoaina Ituaiga Feso'ota'i

P13

MicroSD tulei- tulei

so'oga

P14

1×3-pin 2.54 mm so'oga

P15

3.5mm jack headphone

P17

USB 2.0 Ituaiga A.

P18

JST_SH_2P

P19

1×2-pine so'oga

Fa'amatalaga MicroSD 3.0
Feso'ota'i SWD So'oga MQS So'oga USB So'oga maa RTC So'oga SYS_nRST

Fa'asinoga Vaega Vaega 2.8
Vaega 2.19.1 Vaega 2.6 Vaega 2.13 Mo auiliiliga, tagai i le ata o le laupapa Mo auiliiliga, tagai i le ata o le laupapa

1.6 Oomi faamau

O le ata 4 o loʻo faʻaalia ai faʻamau o loʻo avanoa i luga o le laupapa. Fuafuaga 4 o loʻo faʻamatalaina ai faʻamau o loʻo maua ile FRDM-IMX93.

Laulau 4.FRDM-IMX93 fa'amau fa'amau

Faailoga vaega

Sui igoa

Fa'amau mana

K2, K3

Fa'amau fa'aoga

Fa'amatalaga
O le i.MX 93 applications processor e lagolagoina le fa'aogaina o se fa'ailo fa'aulu fa'amau e talosagaina ai suiga autu o le malosiaga o le SoC (o lona uiga, ON pe OFF) mai le PMIC.
Ole fa'amau ON/OFF e feso'ota'i ile pine ONOFF ole i.MX 93 processor.
· I le setete ON: Afai o le ON/OFF button e umi atu nai lo le taimi o le debounce, o le power off interrupt e fa'atupuina Afai e umi le umi o le ki nai lo le fa'atulagaina o le taimi sili (pe tusa ma le 5 s), o le a alu le setete mai ON i OFF, ma auina atu le PMIC_ON_ REQ faailo e tape ai le mana o le PMIC
· I le tulaga OFF: Afai o le ON/OFF faamau e umi atu nai lo le OFF-toON taimi, o le a alu le setete mai OFF i ON, ma auina atu le PMIC_ON_REQ faailo e ki ai le mana o le PMIC
O fa'amau fa'aoga o lo'o teuina mo fa'aoga fa'apitoa.

1.7 DIP ki
O sui DIP o loʻo faʻaaogaina i luga o le laupapa FRDM-IMX93.
· 4-bit DIP ki SW1 · 2-bit DIP ki SW3 · 1-bit DIP ki SW4 Afai o le DIP sui pine o le:
· OFF pine value o le 0 · ON pine value o le 1 O le lisi o loʻo i lalo o loʻo faʻamatalaina ai le faʻamatalaga ma le faʻatulagaina o sui DIP o loʻo avanoa i luga o le laupapa.

UM12181
Fa'aoga tusi lesona

O fa'amatalaga uma o lo'o tu'uina atu i totonu o lenei pepa e fa'atatau i fa'aletulafono fa'aletulafono.
Rev. 1.0 — 9 Tesema 2024

NXP Semiconductors

UM12181
FRDM-IMX93 Board Tusi Taiala

· SW1 Tuuina atu le faʻatonuga mo le faʻatulagaina o le faʻaulu. Mo auiliiliga, tagai i le Vaega 2.5.
· SW3 Tuuina atu le faʻatonuga mo le faʻatagaina poʻo le tapeina o faailoilo faʻafesoʻotaʻi CAN, CAN_TXD (GPIO_IO25) ma CAN_RXD (GPIO_IO27), i luga o le laupapa.

Laulau 5. SW3 fa'atulagaina

Suiga

Fa'ailoga

Fa'amatalaga

SW3[1]

CAN_TXD (GPIO_IO25)

ON (fa'atonu le fa'ailoga): Fa'aaga le fa'ailoga CAN_TXD OFF: Fa'agata le fa'ailoga CAN_TXD

SW3[2]

CAN_RXD (GPIO_IO27)

ON (fa'atonuina): Fa'aagaoio le faailo CAN_RXD OFF: Ta'e le faailo CAN_RXD

· SW4 E tu'uina atu le fa'atonuga mo le fa'aagaoioia po'o le fa'amalo ole CAN split termination RC filter.

Laulau 6. SW3 fa'atulagaina

Suiga

Fa'ailoga

SW4[1]

Fa'amatalaga
ON (fa'atulagaina fa'aletonu): Fa'aagavaa le fa'amutaina o le RC (62 + 56 pF) ma fa'atulaga le pasi CAN mo galuega masani.
OFF: Fa'agata le fa'agata RC mo le faiga su'ega.

1.8 LED

O le laupapa FRDM-IMX93 o loʻo i ai moli-emitting diodes (LED) e mataʻituina ai galuega faʻaoga, e pei o le faʻaogaina o le eletise ma faʻaletonu laupapa. O faʻamatalaga e aoina mai LED e mafai ona faʻaaogaina mo faʻamoemoega faʻapipiʻi.
O le ata 4 o loʻo faʻaalia ai LED o loʻo avanoa i luga o le laupapa.
Laulau 7 o loʻo faʻamatalaina ai le FRDM-IMX93 LEDs.

Laulau 7. FRDM-IMX93 LEDs Vaega e iloagofie ai lanu LED

D601

Lanu mumu

LED igoa PWR LED

LED1

Mumu / lanumeamata / Blue RGB_LED

O613 D614

ORANGI MUNI

LALA_LALAI_ORANGE

Fa'amatalaga (Pe a SILA le LED)
Fa'ailoa 3.3 V le malosi-on tulaga. A maua le 3.3 V i luga o le va'a, o le D601 LED e ki.
Fa'aoga fa'aoga LED. O nei LED ta'itasi e mafai ona pulea e ala i se fa'aoga fa'aoga. · Uila mumu e feso'ota'i i le pine MPU GPIO_IO13 · O le LED lanumeamata e feso'ota'i i le pine MPU GPIO_IO04 · O le LED lanumoana e feso'ota'i i le pine MPU GPIO_IO12
· D613 ON WLAN tulaga fa'ailoga. A ON, fa'ailoa mai ua fa'atūina le feso'ota'iga WLAN.
· D614 I LE Bluetooth faʻailoga tulaga. A ON, fa'ailoa mai ua fa'atūina le feso'ota'iga Bluetooth.

2 FRDM-IMX93 faʻamatalaga galue

O lenei mataupu o loʻo faʻamatalaina foliga ma galuega a le FRDM-IMX93 laupapa. Manatua: Mo fa'amatalaga o le i.MX93 MPU, va'ai i.MX 93 Applications Processor Reference Manual. Ua vaevaeina le mataupu i vaega nei:
· Vaega “Processor” · Vaega “Power supply” · Vaega “Clocks” · Section “I2C interface”

UM12181
Fa'aoga tusi lesona

O fa'amatalaga uma o lo'o tu'uina atu i totonu o lenei pepa e fa'atatau i fa'aletulafono fa'aletulafono.
Rev. 1.0 — 9 Tesema 2024

NXP Semiconductors

UM12181
FRDM-IMX93 Board Tusi Taiala

· Vaega "Faiga faʻapipiʻi ma le faʻaogaina o masini faʻapipiʻi" · Vaega "PDM interface" · Vaega "LPDDR4x DRAM memory" · Vaega "SD card interface" · Vaega "eMMC memory" · Vaega "M.2 connector ma Wi-Fi / Bluetooth module" · Vaega "CAN interface" · Vaega "USB interface" · Vaega "Kamera interface" · Vaega "MIPI DSI" · Vaega "MIPI DSI" · Vaega "MIPI DSI" · Vaega "MIPI DSI" Vaega “Debug interface” · Vaega “Board errata”

2.1 Processor
O le i.MX 93 applications processor e aofia ai masini e lua Arm Cortex-A55 faʻatasi ma le saoasaoa e oʻo atu i le 1.7 GHz faʻatasi ma se NPU e faʻavaveina ai le aʻoaʻoina o masini. O le fa'amoemoe lautele Arm Cortex-M33 e o'o atu i le 250 MHz e mo le taimi moni ma le maualalo o le gaosiga. O feso'ota'iga fa'atonutonu malosi e mafai ona maua ile CAN-FD. E le gata i lea, lua 1 Gbit/s Ethernet controllers, tasi le lagolago taimi ma'ale'ale networking (TSN), ta'avale faitotoa faitotoa ma maualalo le taofiofia.
O le i.MX 93 e aoga mo talosaga e pei o:
· Fale atamai · Pulea fale · HMI e leai ni fa'afeso'ota'i · Fa'atauga · Soifua Maloloina · Fa'asalalauga IoT
O fa'agaioiga ta'itasi e tu'uina atu ai le 16-bit LPDDR4/LPDDR4X fa'aoga manatua ma isi feso'ota'iga mo feso'ota'iga fa'apitoa, e pei o le MIPI LCD, MIPI Camera, LVDS, WLAN, Bluetooth, USB2.0, uSDHC, Ethernet, FlexCAN, ma multisensors.
Mo nisi fa'amatalaga auiliili e uiga i le gaosiga, taga'i i le i.MX93 pepa fa'amaumauga ma le i.MX 93 Applications Processor Reference Manual ile https://www.nxp.com/imx93.

2.2 Sapalai eletise
O le eletise muamua i le laupapa FRDM-IMX93 o le VBUS_IN (12 V - 20 V) e ala i le USB Type-C PD connector (P1).
E fa DC buck fa'atonutonu suiga o lo'o fa'aogaina:
· MP8759GD (U702) sui VBUS_IN sapalai i le SYS_5V (5 V) sapalai eletise, lea o le sapalai o le eletise mo PCA9451AHNY PMIC (U701) ma isi masini tuufua i luga o le laupapa.
· MP1605C (U723) sui VDD_5V sapalai i DSI&CAM_3V3 (3.3 V / 2 A) mo MIPI CSI ma MIPI DSI. · MP2147GD (U726) sui VDD_5V sapalai i VPCIe_3V3 (3.3 V / 4 A) mo M.2 / NGFF module (P8). · MP1605C (U730) sui VPCIe_3V3 sapalai i VEXT_1V8 (3.3 V / 500 mA) mo luga o le laupapa Wi-Fi module
MAYA-W27x (U731).

UM12181
Fa'aoga tusi lesona

O fa'amatalaga uma o lo'o tu'uina atu i totonu o lenei pepa e fa'atatau i fa'aletulafono fa'aletulafono.
Rev. 1.0 — 9 Tesema 2024

NXP Semiconductors
O le ata 6 o loʻo faʻaalia ai le FRDM-IMX93 faʻapipiʻi eletise poloka poloka.

UM12181
FRDM-IMX93 Board Tusi Taiala

Ata 6. FRDM-IMX93 sapalai eletise Siata 8 o loʻo faʻamatalaina ai puna eletise eseese o loʻo maua i luga o le laupapa.

Laulau 8. FRDM-IMX93 masini faʻapipiʻi eletise

Vaega

Gaosimea

numera vaega e iloagofie ai

tofia

Vaega gaosi oloa

Paoa sapalai

U702

MP8759GD

Malosi Monolithic · DCDC_5V

Systems Inc.

· VSYS_5V

U726

MP2147GD

Monolithic Power VPCIe_3V3 Systems Inc.

Fa'amatalaga Fa'amatalaga

· 5 V i le 8 A 3.3 V i le 3 A

Tuuina atu le malosiaga i:
· PMIC PCA9451AHNY (U701) · NX20P3483UK USB PD ma
Ituaiga-C ki (U710)
· DC tupe MP2147GD (U726) mo VPCIe_3V3
· DC tupe MP1605C (U723) mo DSI&CAM_3V3
· Kisi uta SGM2526 (U733) mo VRPi_5V
· Kisi uta SGM2526 (U742) mo VBUS_USB2_5V
· Sapalai fa'aulu mo sui-faiga fa'aliliu MP1605C (U730)

UM12181
Fa'aoga tusi lesona

O fa'amatalaga uma o lo'o tu'uina atu i totonu o lenei pepa e fa'atatau i fa'aletulafono fa'aletulafono.
Rev. 1.0 — 9 Tesema 2024

NXP Semiconductors

UM12181
FRDM-IMX93 Board Tusi Taiala

Laulau 8. FRDM-IMX93 masini sapalai eletise…fa'aauau

Vaega

Gaosimea

numera vaega e iloagofie ai

tofia

Vaega gaosi oloa

Paoa sapalai

Fa'amatalaga Fa'amatalaga
· Tuuina atu mo le WLAN ma le Bluetooth tulaga faʻaalia LED (D613 ma D614)
· Sapalai mo luga ole Wi-Fi module u-blox MAYA-W27x (U731)

U723

MP1605C

Monolithic Power DSI&CAM_3V3 3.3 V ile 2 A Systems Inc.

Tuuina atu le malosiaga i le MIPI CSI (P6) ma le MIPI DSI (P7) fa'aoga

U730

MP1605C

Monolithic Power VEXT_1V8 Systems Inc.

1.8 V i le 500 mA Tuuina atu le mana i luga ole Wi-Fi u-blox MAYA-W27x module

U701

PCA9451AHNY

NXP

BUCK2: LPD4/

Semiconductors x_VDDQ_0V6

· 0.6 V i le 2000 Tuuina atu le mana i le VDDQ_DDR

sapalai eletise mo CPU DRAM

PHY I/O (LPDDR4/X)

BUCK1/3: VDD_ · VOL (V): 0.8 VDD_SOC, sapalai eletise mo SoC SOC_0V8[1][2] · Ituaiga VOL (V): manatu ma le lima autu
Dynamic voltagu scaling (DVS) Fa'aaliga: Va'ai ile SoC pepa fa'amaumauga.

BUCK4: · VDD_3V3

3.3 V i le 3000 mA

Tuuina atu le malosiaga i:
· MIPI DSI/LVDS · NVCC_GPIO, sapalai eletise mo
GPIO pe a iai ile 3.3 V mode
· VDD_USB_3P3 pine mo USB PHY mana
· eMMC 5.1 masini · MicroSD · EEPROM · Ethernet ports (P3 ma P4) · LVDS i le HDMI converter · I2C IO expander PCAL6524
HEAZ (U725, tuatusi I2C: 0x22)
Punavai mo:
· ENET1_DVDD3 ma ENET1_ AVDD3 sapalai
· OVDD_3V3 mo sapalai AVCC_3V3

BUCK5: · VDD_1V8

1.8 V i le 2000 mA

Sapalai mo:
· LPD4/x_VDD1 · eMMC 5.1 masini · LVDS i le HDMI converter · VDD_ANA_1P8, analog core
sapalai voltage
· NVCC_WAKEUP, numera I/O sapalai

UM12181
Fa'aoga tusi lesona

O fa'amatalaga uma o lo'o tu'uina atu i totonu o lenei pepa e fa'atatau i fa'aletulafono fa'aletulafono.
Rev. 1.0 — 9 Tesema 2024

NXP Semiconductors

UM12181
FRDM-IMX93 Board Tusi Taiala

Laulau 8. FRDM-IMX93 masini sapalai eletise…fa'aauau

Vaega

Gaosimea

numera vaega e iloagofie ai

tofia

Vaega gaosi oloa

Paoa sapalai

BUCK6:
· LPD4/x_ VDD2_1V1

LDO1: NVCC_ BBSM_ 1V8

LDO4: VDD_ ANA_0 P8

LDO5: NVCC_SD

Suiga Uta: VSDs_3V3

U703

FDS4435 (Power SG MICRO Trench MOSFET) CORP

VDD_5V

U732 U733 U737
U742

SGM2525 (Sui uta)
SGM2525 (Sui uta)
TLV76033DBZR (Voltage fa'atonu)

SG MICRO CORP
SG MICRO CORP
Texas Meafaigaluega

SGM2526 (Sui uta)

SG MICRO CORP

VRPi_3V3
VRPi_5V
VCC_3V3_ DEBUG
VBUS_USB2_5 V

Fa'amatalaga Fa'amatalaga

1.1 V i le 2000 mA

Sapalai i: · VDD2_DDR, DDR PHY sapalai voltage

1.8 V i le 10 mA NVCC BBSM I/O sapalai

0.8 V i le 200 mA Analog core sapalai voltage

1.8 V / 3.3 V kata MicroSD

3.3 V

kata MicroSD

5 V / 2.5 A
3.3 V i le 2.5 A 5 V i le 2.5 A 3.3 V 5 V / 2.5 A

Sapalai i: · 10-pin ulu laina lua (P12) · CAN transceiver e ala ile CAN_
VDD_5V · RGB LED Punavai mo: · HDMI_5V · DSI&CAM_3V3 · VPCIe_3V3 · VRPi_5V · VBUS_USB2_5V
· 40-pin ulu laina lua pine (P11)
· 40-pin ulu laina lua pine (P11)
Sapalai i le 4-bit voltagfa'aliliu-tulaga fa'aliliu fa'aoga mo le USB-i-dual UART debug interface
Sapalai ile USB2.0 Type-A Host

[1] BUCK1 ma le BUCK3 o loʻo faʻapipiʻiina e avea ma vaega lua. [2] PCA9451 BUCK1/3 lua vaega fa'aletonu galuega faatino voltage 0.8 V. Polokalama suia i le 0.95 V mo le overdrive mode.
Mo nisi fa'amatalaga i le fa'asologa o le eletise e mana'omia e le i.MX 93, va'ai le vaega "Power sequence" i le i.MX 93 Reference Manual.

2.3 Uati
FRDM-IMX93 e maua uma uati manaʻomia mo le faʻaogaina ma fesoʻotaʻiga lautele. O le laulau 9 o lo'o aoteleina ai fa'amatalaga o uati ta'itasi ma le vaega o lo'o maua ai.

Laulau 9. FRDM-IMX93 uati Vaega e iloagofie Uati generator

Y401

Oscillator tioata

Uati XTALI_24M

Fa'amatalaga Fa'asologa: 24 MHz

Fa'asinomaga Fa'atonuga

UM12181
Fa'aoga tusi lesona

O fa'amatalaga uma o lo'o tu'uina atu i totonu o lenei pepa e fa'atatau i fa'aletulafono fa'aletulafono.
Rev. 1.0 — 9 Tesema 2024

NXP Semiconductors

UM12181
FRDM-IMX93 Board Tusi Taiala

Laulau 9. FRDM-IMX93 uati...fa'aauau Vaega fa'ailoa Uati generator

QZ401

Oscillator tioata

QZ701

Oscillator tioata

Y402

Oscillator tioata

Y403

Oscillator tioata

Y404

Oscillator tioata

Uati XTALO_24M
XTALI_32K XTALO_32K
XIN_32K XOUT_32K
PHY1_XTAL_I PHY1_XTAL_O
PHY2_XTAL_I PHY2_XTAL_O
HDMI_XTALIN HDMI_XTALOUT

Fa'amatalaga

Tulaga

Fa'atele: 32.768 kHz NVCC_BBSM poloka o le fa'atonuga
Auala: 32.768 kHz PCA9451AHNY PMIC

Auala: 25 MHz Ethernet RMII PHY1

Auala: 25 MHz Ethernet RMII PHY2

Faafia: 27 MHz

I luga ole laiga LVDS i le HDMI converter module IT6263 (U719)

2.4 I2C fa'aoga

O le i.MX 93 processor e lagolagoina se laʻititi-malosi inter-integrated circuit (I2C) module e lagolagoina ai se atinaʻe lelei i se I2C-pasi o se matai. O le I2C e tuʻuina atu se auala o fesoʻotaʻiga i le va o le tele o masini o loʻo maua i luga o le laupapa FRDM-IMX93.
E tasi le 10-pin 2 × 5 2.54 mm connector P12 o loʻo tuʻuina atu i luga o le laupapa e lagolago ai fesoʻotaʻiga I2C, CAN, ma ADC. E mafai e le au atiaʻe ona faʻaogaina le taulaga mo nisi faʻaoga faʻapitoa.
Laulau 10 o loʻo faʻamatalaina ai le I2C, CAN, ma le ADC ulutala, P12, pinout.

Laulau 10.10-pin 2×5 2.54mm I2C, CAN, ma ADC ulutala (P12) pine

Igoa faailo

Fa'amatalaga

VDD_3V3

3.3 V eletise sapalai

VDD_5V

5 V eletise sapalai

ADC_IN0

Auala fa'aoga ADC 0

ADC_IN1

Auala fa'aoga ADC 1

I3C_INT

I2C/I3C fa'alavelave fa'ailoga

GND

eleele

I3C_SCL

I2C/I3C SCL faailoilo

CAN_H

E MAFAI e transceiver faailo maualuga

I3C_SDA

I2C/I3C SDA faailoilo

CAN_L

E MAFAI le transceiver maualalo faailoilo

Laulau 11 o loʻo faʻamatalaina ai masini I2C ma latou tuatusi I2C (7-bit) i luga o le laupapa.

Laulau 11.I2C masini

Faailoga vaega

Meafaigaluega

U719

IT6263

U748

PCAL6408AHK

tuatusi I2C (7-bit) Taulaga

Saosaoa

0x4C (0b’1001100x) MX-I2C1 0x20 (0b’0100000x) MX-I2C1

1 MHz Fm+ 1 MHz Fm+

Voltagu Fa'amatalaga

3.3 V 3.3 V

LVDS i le HDMI liliu
I/O fa'alautele mo IRQ / OUTPUT

UM12181
Fa'aoga tusi lesona

O fa'amatalaga uma o lo'o tu'uina atu i totonu o lenei pepa e fa'atatau i fa'aletulafono fa'aletulafono.
Rev. 1.0 — 9 Tesema 2024

NXP Semiconductors

UM12181
FRDM-IMX93 Board Tusi Taiala

Laulau 11.I2C masini…fa'aauau

Faailoga vaega

Meafaigaluega

U701

PCA9451AHNY

U725

PCAL6524HEAZ

U10 U705

AT24C256D PTN5110NHQZ

U712

PTN5110NHQZ

U710

NX20P3483UK

U740

PCF2131

tuatusi I2C (7-bit) Taulaga

0x25 (0b’0100101x) MX-I2C2

0x22 (0b’01000[10]x)

MX-I2C2

0x50 (0b’1010000x) MX-I2C2

0x52 (0b’10100[10]x)

MX-I2C3

0x50 (0b’10100[00]x)

MX-I2C3

0x71 (0b’11100[01]x)

MX-I2C3

0x 53 (0b’110101[0]x)

MX-I2C3

Saosaoa 1 MHz Fm+ 1 MHz Fm+ 1 MHz Fm+ 1 MHz Fm+ 1 MHz Fm+ 1 MHz Fm+ 1 MHz Fm+

Voltagu Fa'amatalaga

3.3 V 3.3 V
3.3 V 3.3 V
3.3 V
3.3 V

PMIC
IO fa'alautele mo IRQ/ OUTPUT
EEPROM
USB Type-C La'uina Malosiaga PHY
USB Type-C La'uina Malosiaga PHY
Suia uta USB

3.3 V RTC fafo

2.5 Faiga fa'aa'e ma le fa'atūina o masini fa'apipi'i
O le i.MX 93 processor e ofoina atu le tele o faʻamaufaʻailoga taʻavale, lea e mafai ona filifilia e SW1 i luga o le laupapa FRDM-IMX93 poʻo mai le faʻapipiʻi faʻaputu o loʻo teuina i luga o le eFUSE i totonu o le processor. E le gata i lea, e mafai e le i.MX 93 ona siiina se ata o le polokalama mai se fesoʻotaʻiga USB pe a faʻapipiʻiina i le faasologa o le download. O pine fa'apitoa e fa o le BOOT MODE e fa'aaogaina e filifili ai ituaiga fa'a ta'avale eseese.
O le ata 7 o lo'o fa'aalia ai le suiga o le filifiliga o le boot mode.

UM12181
Fa'aoga tusi lesona

O fa'amatalaga uma o lo'o tu'uina atu i totonu o lenei pepa e fa'atatau i fa'aletulafono fa'aletulafono.
Rev. 1.0 — 9 Tesema 2024

NXP Semiconductors

UM12181
FRDM-IMX93 Board Tusi Taiala

Ata 7. Su'e filifiliga faiga fa'a-fa'aa'e O le laulau 12 o lo'o fa'amatalaina ai le tau o le SW1 o lo'o fa'aogaina i ituaiga ta'avale eseese.

Fuafuaga 12. Fa'atonu faiga fa'avae

SW1 [3:0]

BOOT_MODE[3:0]

0001

0010

0011

Fa'aautu o le ta'avale Cortex-A

Meafaigaluega fa'atūina La'u fa'asologa (USB) uSDHC1 8-bit eMMC 5.1 uSDHC2 4-bit SD3.0

I luga o le laupapa FRDM-IMX93, o le faʻaogaina o le taʻavale e mai le masini eMMC. O le isi masini taʻavale o le microSD connector. Seti le SW1[3:0] e pei o le 0010 e filifili ai le uSDHC1 (eMMC) e fai ma masini taʻavale, seti le 0011 e filifili ai le uSDHC2 (SD), ma seti le 0001 e ulufale ai i le USB serial download.
Fa'aaliga: Mo nisi fa'amatalaga e uiga i faiga ta'avale ma le fa'atulagaina o masini ta'avale, va'ai le mataupu "System Boot" i le i.MX 93 Applications Processor Reference Manual.
Ata 8 o loʻo faʻaalia ai le fesoʻotaʻiga o le SW1 ma le i.MX 93 faʻailoga faʻailoga faʻailoga.

UM12181
Fa'aoga tusi lesona

O fa'amatalaga uma o lo'o tu'uina atu i totonu o lenei pepa e fa'atatau i fa'aletulafono fa'aletulafono.
Rev. 1.0 — 9 Tesema 2024

NXP Semiconductors

UM12181
FRDM-IMX93 Board Tusi Taiala

Ata 8. Boot configuration schematic

2.6 PDM fa'aoga

O le fa'aogaina o masini faaleotele leo (PDM) e maua ai le lagolago a le PDM/MQS i le FRDM-IMX93, ma e feso'ota'i atu i le 3.5 mm leo leo (P15).

Laulau 13.Leo leo Faailoga Vaega
P15

Numera vaega ole gaosiga PJ_3536X

Fa'amatalaga 3.5 mm leo leo mo luga o le MQS analog fa'aoga / gaioiga

2.7 LPDDR4x DRAM manatua
O le laupapa FRDM-IMX93 o loʻo iai le 1 Gig × 16 (1 channel × 16 I / O × 1 rank) LPDDR4X SDRAM chip (MT53E1G16D1FW-046 AAT: A) mo le aofaʻi o le 2 GB o le RAM manatua. O le LPDDR4x DRAM manatua e fesoʻotaʻi i le i.MX 93 DRAM pule.
O le ZQ calibration resistors (R209 ma R2941) faʻaaogaina e le LPDDR4x chip e 240 1% i le LPD4 / x_VDDQ ma le ZQ calibration resistor DRAM_ZQ faʻaaogaina i i.MX93 SoC itu o le 120 1% i le GND.
I le faʻatulagaina o le tino, o loʻo tuʻuina le pu LPDDR4X i le pito i luga o le laupapa. O faʻamaumauga faʻamaumauga e le o fesoʻotaʻi ma le LPDDR4x meataalo i le faʻasologa faʻasolosolo. Ae, o fa'amaumauga o fa'amaumauga e feso'ota'i e pei ona fa'amoemoeina e ala i le fa'atulagaina ma isi fa'ailoga taua mo le fa'afaigofieina o auala.

UM12181
Fa'aoga tusi lesona

O fa'amatalaga uma o lo'o tu'uina atu i totonu o lenei pepa e fa'atatau i fa'aletulafono fa'aletulafono.
Rev. 1.0 — 9 Tesema 2024

NXP Semiconductors

UM12181
FRDM-IMX93 Board Tusi Taiala

2.7.1 LPDDR4X i le LPDDR4 femalagaiga
O le vaega FRDM-IMX93 DRAM o le MT53E1G16D1FW-046 AAT: A e lagolagoina uma auala LPDDR4X ma LPDDR4, peitaʻi, ua filifilia le LPDDR4X e fai ma filifiliga le lelei i luga o le laupapa. Ina ia faʻamaonia le LPDDR4, o auala e lua e faʻapea:
· Toe fai le DRAM VDDQ mana i le 1.1 V e lagolago ai le LPDDR4 e ala i le faia o laasaga nei: 1. Aveese R704 2. Faʻapipiʻi R702 3. Ia mautinoa o loʻo fetaui le DRAM ma le LPDDR4 manaʻomia.

Ata 9.LPDDR4 toe fa'aleleia · Leai se meafaigaluega toe fa'aleleia e mana'omia. Suia le DRAM VDDQ mana i le 1.1 V e ala ile polokalama e faʻapipiʻi ai le PMIC
e le I2C ina ua uma le malosiaga o le faiga.
2.8 SD card interface
O le fa'atonuga fa'atatau e tolu fa'amautu fa'akomepiuta fa'atonu (uSDHC) modules mo le SD/eMMC feso'ota'iga lagolago. O le uSDHC2 interface o le i.MX 93 processor e fesoʻotaʻi ma le MicroSD card slot (P13) i luga o le laupapa FRDM-IMX93. E lagolagoina e lenei so'o se tasi 4-bit SD3.0 MicroSD card. Ina ia filifilia e avea ma masini ta'avale o le laupapa, tagai i le Vaega 2.5.
2.9 eMMC manatua
O le eMMC memory (i le SOM board) e fesoʻotaʻi atu i le uSDHC1 interface o le i.MX 93 processor, lea e mafai ona lagolagoina eMMC 5.1 masini. O le masini fa'ato'a fa'aletonu o le laupapa. O le laulau 12 o lo'o fa'amatalaina ai le fa'atulagaina o ta'avale. Laulau 14 o loʻo faʻamatalaina ai le masini manatua eMMC o loʻo lagolagoina e le uSDHC1 interface.

UM12181
Fa'aoga tusi lesona

O fa'amatalaga uma o lo'o tu'uina atu i totonu o lenei pepa e fa'atatau i fa'aletulafono fa'aletulafono.
Rev. 1.0 — 9 Tesema 2024

NXP Semiconductors

UM12181
FRDM-IMX93 Board Tusi Taiala

Laulau 14. Lagolago eMMC masini Fa'ailoa vaega Numera vaega

U501

FEMDRM032G-A3A55

Fa'atonuga 256 Gb x1

FBGA TFBGA-153

FA'AALIGA FAAVAE

Tele le manatua 32 GB

2.10 M.2 so'oga ma Wi-Fi/Bluetooth module

O le laupapa FRDM-IMX93 e lagolagoina le M.2/NGFF Key E mini card 75-pin connector, P8. O le M.2 mini card connector e lagolagoina le USB, SDIO, SAI, UART, I2C, ma le fesoʻotaʻiga GPIO. Ona o le le mafai, o nei faailo e fesoʻotaʻi ma le Wi-Fi module i luga o le laupapa, peitaʻi, e faʻaaoga lenei M.2 slot, e tatau ona toe faʻaleleia mea nei tetee.

Fuafuaga 15. Toe fa'aleleia mo le fa'aogaina o le slot M.2 Resistors DNP R2808, R2809, R2812, R2819, R2820, R2821 R3023, R3024, R2958, R3028 R2854, R2855 R3038, R2870 R2871, R2796 R2798 R2800, R2802, R2797 R2799, R2801, R2805, R2832 R2834, R2836, R2838, RXNUMX

Resistors faʻapipiʻi R2824, R2825, R2826, R2827, R2828, R2829 R2960, R2860 R2851, R2853 R3037, R2866, R2867 R2788, R2791, R2792, R2794, R2789, R2790, R2793 R2795, R2833 R2835, R2837, R2839, RXNUMX

E mafai ona fa'aogaina le feso'ota'iga M.2 mo kata Wi-Fi / Bluetooth, IEEE802.15.4 Leitio, po'o kata 3G / 4G. Siata 16 o loʻo faʻamatalaina ai le pine o le M.2 mini card connector (P8).

Laulau 16.M.2 laititi kata so'oga (P8) pinout

M.2 mini card connector pine Fa'amatalaga feso'ota'iga

numera

2, 4, 72, 3V3_1, 3V3_2, 3V3_3, 3V3_4 Fesoʻotaʻi i le VPCIe_3V3 sapalai eletise 74

LED1

Faʻafesoʻotaʻi i le M.2 Green LED, D613

I2S_SCK

Feso'ota'i i le pine fa'apipi'i SAI1_TXC pe a fa'atumuina le R2788

I2S_WS

Feso'ota'i i le pine fa'apipi'i SAI1_TXFS pe a fa'atumuina le R2791

I2S_SD_IN

Feso'ota'i i le pine fa'apipi'i SAI1_RXD pe a fa'atumuina le R2794

I2S_SD_OUT

Feso'ota'i i le pine fa'apipi'i SAI1_TXD pe a fa'atumuina le R2792

LED2

Faʻafesoʻotaʻi i le M.2 Orange LED, D614

UART_WAKE

M2_UART_nWAKE fa'aoga mo le fa'alautele I/O (PCAL6524HEAZ, P0_3, tuatusi I2C: 0x22) pe a fa'atumuina le R2853

UART_RXD

Fa'afeso'ota'i i le UART5_RXD pe a fa'atumuina le R2835

UART_TXD

Feso'ota'i ile UART5_TXD pe'ā fa'anofoina le R2833

UART_CTS

Feso'ota'i i le UART5_CTSI pe a fa'anofoina le R2839

UART_RTS

Feso'ota'i ile UART5_RTSO pe'a fa'anofoina R2837

VEN_DEF1

Feso'ota'i ile SPI3_MOSI pe a fa'anofoina le R2790

VEN_DEF2

Feso'ota'i i le SPI3_MISO pe a fa'anofoina le R2795

VEN_DEF3

Feso'ota'i i le SPI3_CLK pe a fa'aola R2793

UM12181
Fa'aoga tusi lesona

O fa'amatalaga uma o lo'o tu'uina atu i totonu o lenei pepa e fa'atatau i fa'aletulafono fa'aletulafono.
Rev. 1.0 — 9 Tesema 2024

NXP Semiconductors

UM12181
FRDM-IMX93 Board Tusi Taiala

Laulau 16.M.2 tama'i kata feso'ota'i (P8) pinout…fa'aauau

M.2 mini card connector pine Fa'amatalaga feso'ota'iga

numera

SUSCLK

Feso'ota'i ile PMIC_32K_OUT, fa'atupu e le PCA9451AHNY PMIC

PERST0

M2_nRST fa'aoga mo le fa'alautele I/O (PCAL6524HEAZ, P2_2, tuatusi I2C: 0x22)

W_FAGA2

M2_nDIS2 fa'aoga mo le fa'alautele I/O (PCAL6524HEAZ, P2_3, tuatusi I2C: 0x22) pe a fa'atumuina le R2867

W_FAGA1

M2_nDIS1 fa'aoga mo le fa'alautele I/O (PCAL6524HEAZ, P2_4, tuatusi I2C: 0x22) pe a fa'atumuina le R2866

I2C_DATA

Feso'ota'i ile pine SDAL ole PCA9451AHNY PMIC

I2C_CLK

Feso'ota'i ile pine SCLL ole PCA9451AHNY PMIC

ALERT

M2_nALERT fa'aoga mo le fa'alautele I/O (PCAL6524HEAZ, P1_2, tuatusi I2C: 0x22) pe a fa'atumuina le R2860

USB_D +

Feso'ota'i i le USB2_D_P fa'apipi'i fa'apipi'i pe a fa'atumuina le R2806

USB_D-

Feso'ota'i i le USB2_D_N pe a fa'atumuina le R2807

SDIO_CLK

Feso'ota'i i le SD3_CLK processor pine ma le processor interface SDHC3 pe afai o R2824 o lo'o nofoia

SDIO_CMD

Feso'ota'i i le SD3_CMD processor pine ma le processor interface SDHC3 pe afai o R2825 o lo'o nofoia

SDIO_DATA0

Feso'ota'i i le SD3_DATA0 fa'apipi'i pine ma le fa'aogaina o feso'ota'iga SDHC3 pe a fa'atumuina le R2826

SDIO_DATA1

Feso'ota'i i le SD3_DATA1 fa'apipi'i pine ma le fa'aogaina o feso'ota'iga SDHC3 pe a fa'atumuina le R2827

SDIO_DATA2

Feso'ota'i i le SD3_DATA2 fa'apipi'i pine ma le fa'aogaina o feso'ota'iga SDHC3 pe a fa'atumuina le R2828

SDIO_DATA3

Feso'ota'i i le SD3_DATA3 fa'apipi'i pine ma le fa'aogaina o feso'ota'iga SDHC3 pe a fa'atumuina le R2829

SDIO_WAKE

Feso'ota'i i le CCM_CLKO1 fa'apipi'i fa'apipi'i o le NVCC_WAKEUP module pe a fa'atumuina R2851

SDIO_RST

SD3_nRST sau mai le I/O fa'alautele (PCAL6524HEAZ, P1_4, tuatusi I2C: 0x22) pe a fa'atumuina le R3037

PEWAKE0

PCIE_nWAKE fa'aoga mo le fa'alautele I/O (PCAL6524HEAZ, P0_2, tuatusi I2C: 0x22) pe a fa'atumuina le R2868

Mo nisi fa'amatalaga e uiga i feso'ota'iga i.MX 93, va'ai i.MX 93 Applications Processor Reference Manual.

2.11 Fa'aoga tolu-leitio module

O le laupapa FRDM-IMX93 o loʻo faʻaalia ai le Tri-radio (Wi-Fi 6, Bluetooth 5.4, ma le 802.15.4) module e fesoʻotaʻi ma le SD2, UART5, SAI1, ma le SPI3 pule o le faʻatonuga faʻatulagaina.

Laulau 17. Tri-leitio module

Faailoga vaega

Numera vaega ole gaosiga

U731

MAYA-W27x (u-blox)

Fa'amatalaga
Wi-Fi 6, Bluetooth 5.4, ma le 802.15.4 fa'aoga mo le IoT talosaga

UM12181
Fa'aoga tusi lesona

O fa'amatalaga uma o lo'o tu'uina atu i totonu o lenei pepa e fa'atatau i fa'aletulafono fa'aletulafono.
Rev. 1.0 — 9 Tesema 2024

NXP Semiconductors

UM12181
FRDM-IMX93 Board Tusi Taiala

O pine antenna e lua (RF_ANT0 ma le RF_ANT1) o le module e fesoʻotaʻi i fesoʻotaʻiga U.FL P9 ma P10 (DNP e le mafai). O lo'o tu'uina atu le module i le VPCIe_3V3, VEXT_1V8, ma le VDD_1V8.
O le MAYA-W27x module ma le M.2 fesoʻotaʻiga faʻasoa ni laina faʻafesoʻotaʻi i luga o le laupapa FRDM-IMX93. Zeroohm resistors e mafai ai ona filifili faailo i le va o nei vaega.
SD3 Fa'aoga
O laina fesoʻotaʻiga SD3 o loʻo faʻasoa i le va o le MAYA-W27x module ma le M.2 connector. Zero-ohm resistors filifili pe o le MAYA-W27x module (faʻatulagaina tulaga) poʻo le fesoʻotaʻiga M.2.
UART5 Fa'aoga
E faʻapea foʻi, o laina fesoʻotaʻiga UART5 e faʻasoa i le va o le MAYA-W27x module ma le M.2 connector. Zeroohm tete'e filifili pe o le MAYA-W27x module (fa'atulagaina tulaga) po o le M.2 connector.
SAI1 Fesootaiga
O laina fesoʻotaʻiga SAI1 o loʻo faʻasoa i le va o le MAYA-W27x module ma le M.2 connector. Zero-ohm tete'e filifili a le MAYA-W27x module (fa'atulagaina fa'aletonu) po'o le M.2 connector mo 1.8 V fa'aliliu fa'ailoga, fa'atupuina e fa'aaoga ai le 74AVC4T3144 bidirectional voltage faaliliu (U728).
SPI3 Feso'ota'iga
O faʻailoga SPI3 (CLK, MOSI, MISO, ma CS0) e faʻateleina faʻatasi ma faʻailoga GPIO_IO [08, 09, 10, 11], i le faasologa. O nei faailo SPI3 o loʻo faʻasoa i le va o le MAYA-W27x module ma le M.2 connector. Zeroohm tete'e filifili a le MAYA-W27x module (fa'atulagaina tulaga) po o le M.2 connector mo 1.8 V fa'aliliu faailoilo, fa'atupuina e fa'aaoga ai le 74AVC4T3144 bidirectional voltage faaliliu (U729).

UM12181
Fa'aoga tusi lesona

O fa'amatalaga uma o lo'o tu'uina atu i totonu o lenei pepa e fa'atatau i fa'aletulafono fa'aletulafono.
Rev. 1.0 — 9 Tesema 2024

NXP Semiconductors

UM12181
FRDM-IMX93 Board Tusi Taiala

Ata 10. Fa'atonuga o mea fa'asaga mo SD3

UM12181
Fa'aoga tusi lesona

O fa'amatalaga uma o lo'o tu'uina atu i totonu o lenei pepa e fa'atatau i fa'aletulafono fa'aletulafono.
Rev. 1.0 — 9 Tesema 2024

NXP Semiconductors

UM12181
FRDM-IMX93 Board Tusi Taiala

Ata 11. Fa'atonuga fa'atutu mo SAI1, UART5, ma SPI3
2.12 CAN interface
O le i.MX93 processor e lagolagoina le faʻaogaina o fesoʻotaʻiga eria (CAN) module o se faʻatautaia fesoʻotaʻiga o loʻo faʻatinoina le CAN protocol e tusa ai ma le CAN faʻatasi ai ma le fetuutuunai o faʻamaumauga faʻamaumauga (CAN FD) ma le CAN 2.0B protocol specification. E lagolagoina e le processor le CAN FD controllers e lua.
I luga o le laupapa FRDM-IMX93, o se tasi o pule e fesoʻotaʻi atu i le televave CAN transceiver TJA1051T/3. O le CAN transceiver maualuga-saosaoa e ave ai faailo CAN i le va o le faʻaogaina o le gaosiga ma le 10-pin 2 × 5 2.54 mm ulutala (P12) i lana pasi CAN e lua-uaea faaletino.
O faailo CAN_TXD ma CAN_RXD o loʻo faʻateleina ile GPIO_IO25 ma le GPIO_IO27. I luga o le laupapa, o le 2-bit DIP switch (SW3) o loʻo faʻaaogaina e pulea ai faailo CAN. Mo fa'amatalaga SW3, va'ai le Vaega 1.7. O le faailo CAN_STBY mai le IO expander PCAL6524HEAZ (U725, P2_7, I2C tuatusi: 22) e mafai ai / fa'agata le CAN standby mode.

UM12181
Fa'aoga tusi lesona

O fa'amatalaga uma o lo'o tu'uina atu i totonu o lenei pepa e fa'atatau i fa'aletulafono fa'aletulafono.
Rev. 1.0 — 9 Tesema 2024

NXP Semiconductors

UM12181
FRDM-IMX93 Board Tusi Taiala

O le CAN interface circuit e aofia ai le vaeluaga fa'amuta RC faamama (62 + 56pF) mo le leo teena ma fa'ailoga amio sa'o. O le ki SW4 o lo'o tu'uina atu mo le fa'aagaoioiga/fa'aletonu le fa'amama RC. Mo fa'amatalaga SW4, va'ai le Vaega 1.7.
O le HS-CAN transceiver ma le ulutala o loʻo faʻamatalaina i le Laulau 18.

Laulau 18. High-speed CAN transceiver ma ulutala

Faailoga vaega

Numera vaega ole gaosiga

Fa'amatalaga

U741

TJA1051T/3

Tele saosaoa CAN transceiver. Tuuina atu se feso'ota'iga i le va o le CAN protocol controller ma le tino e lua-uaea CAN pasi.

P12

E le agavaa ai

10-pin 2×5 2.54 mm so'oga (P12). E feso'ota'i i le pasi CAN ma

fa'atagaina feso'ota'iga i fafo ma le pasi.

Fa'aaliga: O lo'o fa'amatala mai e le Laulau 10 le pine mo le feso'ota'iga 10-pin 2×5 2.54 mm P12.

Fa'aaliga: Mo fa'amatalaga e uiga i TJA1051, va'ai TJA1051 pepa fa'amaumauga ile nxp.com.

2.13 fa'aoga USB

O le i.MX 93 applications processor e lua USB 2.0 controllers, faatasi ai ma le lua USB PHYs fa'atasi. I luga o le laupapa FRDM-IMX93, o le tasi e faʻaaogaina mo le USB2.0 Type-C Port (P2) ma le isi e faʻaaogaina mo le USB2.0 Type-A Port (P17).
Siata 19 o loʻo faʻamatalaina ai pusa USB o loʻo maua i luga o le laupapa.

Laulau 19. Uafu USB Vaega e iloagofie ai Ituaiga Taulaga USB

USB2.0 Ituaiga-C

P17

USB2.0 Ituaiga-A

USB Ituaiga-C PD

P16

USB Ituaiga-C

Fa'amatalaga
Feso'ota'i i le USB host ma le fa'atonu masini (USB 1) o le fa'atonuga. E mafai ona galue o se masini poʻo se talimalo. O le USBC_VBUS faailo e pulea le VBUS drive mo le USB port.
Feso'ota'i i le USB host ma le fa'atonu masini (USB 2) o le fa'atonuga. E mafai ona galue o se masini poʻo se talimalo. O le USB2_VBUS faailo e pulea le VBUS drive mo le USB port. O faailo USB2_DP ma USB2_DN mai le USB2 controller o le faʻaogaina o le faʻaogaina e fesoʻotaʻi i le USB2 Type A port (P17) ona o le faaletonu. O nei faailo e mafai ona fesootai i M.2 card connecter (P6) e solder/DNP R2803, R2804, R2806, R2807.
E fa'aaogaina mo na'o le mana. E le lagolagoina le fa'aliliuina o fa'amatalaga USB. E na'o le pau lea o le uafu sapalai eletise o lea e tatau lava ona tu'uina atu mo le eletise.
O lo'o fa'aaogaina mo le fa'amoemoe o le debug system. Mo fa'amatalaga, va'ai le vaega debug system.

2.14 Ata pu'eata
O le i.MX 93 processor e aofia ai le telefoni feavea'i fa'agaioiga fa'agaoioiga atina'e (MIPI) mea pu'eata fa'asologa fa'asologa 2 (CSI-2) e fa'afoeina fa'amaumauga o fa'amaumauga mai mea pu'eata ma lagolagoina e o'o atu i le 2 laina fa'amaumauga. O faʻailoga MIPI CSI-2 e fesoʻotaʻi atu i se fesoʻotaʻiga FPC lea e mafai ona faʻapipiʻi ai le RPI-CAM-MIPI (Numera Agile: 53206). O le faʻamatalaga o le fesoʻotaʻiga FPC e pei o lalo
· Fa'ailoga vaega: P6 · Laulau 20 o lo'o fa'amatalaina ai le pine fa'afeso'ota'i FPC

UM12181
Fa'aoga tusi lesona

O fa'amatalaga uma o lo'o tu'uina atu i totonu o lenei pepa e fa'atatau i fa'aletulafono fa'aletulafono.
Rev. 1.0 — 9 Tesema 2024

NXP Semiconductors

UM12181
FRDM-IMX93 Board Tusi Taiala

Laulau 20. MIPI CSI connector (P6) pinout

Numera pine

Fa'ailoga

1, 4, 7, 10, 13, 16, 19 GND

MIPI_CSI1_D0_N

MIPI_CSI1_D0_P

MIPI_CSI1_D1_N

MIPI_CSI1_D1_P

MIPI_CSI1_CLK_N

MIPI_CSI1_CLK_P

CSI_nRST

CAM_MCLK

USB_I2C_SCL

USB_I2C_SDA

DSI&CAM_3V3

Fa'amatalaga Ground MIPI CSI alavai fa'amaumauga 0
MIPI CSI alavai fa'amaumauga 1
MIPI CSI uati faailoilo
Toe seti le faailo mai le I/O expander U725 (PCAL6524HEAZ, P2_6, tuatusi I2C: 0x22) 3.3 V voltage fa'aliliu fa'aoga mai CCM_CLKO3 pine (CSI_MCLK) o le fa'atonuga fa'atonu 3.3 V I2C3 SCL fa'ailo 3.3 V I2C3 SDA fa'ailoga 3.3 V sapalai eletise

2.15 MIPI DSI

O le i.MX 93 processor e lagolagoina le MIPI faʻaalia faʻasalalauga faʻasalalau (DSI) e lagolagoina e oʻo atu i le fa ala ma le iugafono e mafai ona oʻo atu i le 1080p60 poʻo le 1920x1200p60.
O fa'amaumauga a le MIPI DSI ma fa'ailo o le uati mai le fa'atonuga fa'atatau e feso'ota'i atu i le feso'ota'iga FPC 22-pin (P7).
Siata 21 o lo'o fa'amatalaina ai le pinout o feso'ota'iga DSI.

Laulau 21. MIPI DSI connector (P7) pinout

Numera pine

Fa'ailoga

1, 4, 7, 10, 13, 16, 19

GND

DSI_DN0

DSI_DP0

DSI_DN1

DSI_DP1

DSI_CN

DSI_CP

DSI_DN2

DSI_DP2

DSI_DN3

DSI_DP3

CTP_RST

DSI_CTP_nINT

Fa'amatalaga Ground MIPI DSI alavai fa'amaumauga 0
MIPI DSI alavai fa'amaumauga 1
MIPI DSI uati faailoilo
MIPI DSI alavai fa'amaumauga 2
MIPI DSI alavai fa'amaumauga 3
Toe seti le faailo mai le I/O expander U725 (PCAL6524HEAZ, P2_1, tuatusi I2C: 0x22) Fa'alavelave fa'ailo ile I/O expander U725 (PCAL6524HEAZ, P0_7, tuatusi I2C: 0x22)

UM12181
Fa'aoga tusi lesona

O fa'amatalaga uma o lo'o tu'uina atu i totonu o lenei pepa e fa'atatau i fa'aletulafono fa'aletulafono.
Rev. 1.0 — 9 Tesema 2024

NXP Semiconductors

UM12181
FRDM-IMX93 Board Tusi Taiala

Laulau 21. MIPI DSI connector (P7) pinout…fa'aauau

Numera pine

Fa'ailoga

USB_I2C_SCL

USB_I2C_SDA

DSI&CAM_3V3

Fa'amatalaga 3.3 V I2C3 SCL fa'ailoga 3.3 V I2C3 SDA fa'ailoga 3.3 V sapalai eletise

2.16 HDMI fa'aoga
O le i.MX 93 processor e lagolagoina se faʻamatalaga faʻamatalaga LVDS TX faʻamatalaga, o le iugafono e mafai ona oʻo atu i le 1366x768p60 poʻo le 1280x800p60. O nei faʻailoga e fesoʻotaʻi atu i le tasi-malaga taʻitasi De-SSC LVDS i le HDMI converter IT6263. O le gaosiga o le IT6263 e feso'ota'i ile feso'ota'iga HDMI P5. O le so'oga e pei ona fa'aalia i le Ata 3.

2.17 Ethernet
O le i.MX 93 processor e lagolagoina le lua Gigabit Ethernet controllers (mafai ona fa'agaioi fa'atasi) fa'atasi ai ma le lagolago mo Energy-Efficient Ethernet (EEE), Ethernet AVB, ma le IEEE 1588.
O le Ethernet subsystem o le laupapa e tuʻuina atu e le Motorcomm YT8521SH-CA Ethernet transceivers (U713, U716) lea e lagolagoina RGMII ma faʻafesoʻotaʻi i fesoʻotaʻiga RJ45 (P3, P4). O le Ethernet transceivers (poʻo PHYs) maua faʻailoga masani RGMII Ethernet mai i.MX 93. O fesoʻotaʻiga RJ45 faʻapipiʻi le Magnetic transformer i totonu, ina ia mafai ona fesoʻotaʻi saʻo i Ethernet transceivers (poʻo PHYs).
O taulaga Ethernet taʻitasi e iai se tuatusi MAC tulaga ese, lea e tuʻufaʻatasia i le i.MX 93. O fesoʻotaʻiga Ethernet o loʻo faʻamaonia manino i luga o le laupapa.

2.18 Fa'alautele feso'ota'iga

E tasi le 40-pin lua-laina pine connector (P11) o loʻo tuʻuina atu i luga o le laupapa FRDM-IMX93 e lagolago ai fesoʻotaʻiga I2S, UART, I2C, ma GPIO. O le ulutala e mafai ona faʻaoga e maua ai pine eseese pe faʻapipiʻi i kata faʻaoga, e pei o le LCD faʻaaliga TM050RDH03, 8MIC-RPI-MX8 kata, MX93AUD-HAT.
O loʻo faʻaalia le fesoʻotaʻiga i le Ata 3.

Laulau 22.P11 fa'amatalaga pine

Numera pine

igoa Net

VRPi_3V3

GPIO_IO02

GPIO_IO03

GPIO_IO04

GND

GPIO_IO17

GPIO_IO27

GPIO_IO22

VRPi_3V3

GPIO_IO10

GPIO_IO09

GPIO_IO11

Numera pine 2 4 6 8 10 12 14 16 18 20 22 24

igoa ole VRPi_5V VRPi_5V GND GPIO_IO14 GPIO_IO15 GPIO_IO18 GND GPIO_IO23 GPIO_IO24 GND GPIO_IO25 GPIO_IO08

UM12181
Fa'aoga tusi lesona

O fa'amatalaga uma o lo'o tu'uina atu i totonu o lenei pepa e fa'atatau i fa'aletulafono fa'aletulafono.
Rev. 1.0 — 9 Tesema 2024

NXP Semiconductors

UM12181
FRDM-IMX93 Board Tusi Taiala

Laulau 22.P11 fa'auiga pine...fa'aauau

Numera pine

igoa Net

GND

GPIO_IO00

GPIO_IO05

GPIO_IO06

GPIO_IO13

GPIO_IO19

GPIO_IO26

GND

Numera pine 26 28 30 32 34 36 38 40

Igoa upega GPIO_IO07 GPIO_IO01 GND GPIO_IO12 GND GPIO_IO16 GPIO_IO20 GPIO_IO21

2.19 Debug atina'e
O le laupapa FRDM-IMX93 o loʻo iai ni fesoʻotaʻiga tutoʻatasi e lua.
· Fa'aulu fa'aulu uaea (SWD) (Vaega 2.19.1) · USB-i-Dual UART debug port (Vaega 2.19.2)
2.19.1 SWD fa'aoga
O le i.MX 93 applications processor e lua fa'ailoga uaea debug (SWD) fa'ailoga i pine tu'ufa'atasi, ma o na fa'ailoga e feso'ota'i sa'o i le tulaga masani 3-pin 2.54 mm connector P14. O faailo SWD e lua o loʻo faʻaaogaina e le gaosiga o:
· SWCLK (Serial wire clock) · SWDIO (Serial wire data input / output) O le SWD connector P14 o loʻo faʻaalia i le Ata 3.
2.19.2 USB debug fa'aoga
O le i.MX 93 applications processor e ono tuto'atasi ports UART (UART1 UART6). I luga o le laupapa FRDM-IMX93, UART1 o loʻo faʻaaogaina mo Cortex-A55 autu, ma UART2 faʻaaogaina mo Cortex-M33 autu. O le USB pu e tasi i le UART lua e faʻaaogaina mo le faʻamoemoega debug. Ole numera ole vaega ole CH342F. E mafai ona e siiina mai le avetaavale mai le WCH Webnofoaga.
A maeʻa ona faʻapipiʻi le avetaʻavale CH342F, e faʻamatala e le PC / USB ports e lua COM e fesoʻotaʻi ma le P16 fesoʻotaʻiga e ala i le USB cable:
· COM Port 1: Cortex-A55 system debugging · COM Port 2: Cortex-M33 system debugging E mafai ona e fa'aogaina meafaigaluega fa'aoga nei mo le fa'aogaina o fa'amoemoega:
· Putty · Tera Term · Xshell · Minicom>=2.9 Ina ia debug i lalo o Linux, ia mautinoa o loʻo faʻapipiʻi le avetaavale CH342F Linux.
O le laulau 23 o loʻo faʻamatalaina ai tulaga manaʻomia.

UM12181
Fa'aoga tusi lesona

O fa'amatalaga uma o lo'o tu'uina atu i totonu o lenei pepa e fa'atatau i fa'aletulafono fa'aletulafono.
Rev. 1.0 — 9 Tesema 2024

NXP Semiconductors

UM12181
FRDM-IMX93 Board Tusi Taiala

Fuafuaga 23. Fa'amaufa'ailoga fa'amaufa'ailoga Fa'amaumauga Fa'amaumauga Fa'amaumauga Fa'amaumauga Parity Stop bits

115,200 Baud 8 Leai 1

O le USB debug connector P16 o loʻo faʻaalia i le Ata 3.

2.20 Fa'atonu sese
Leai se laupapa sese.

3 Galulue ma mea fa'aoga
O lenei vaega o loʻo faʻamatalaina pe faʻafefea ona faʻavaeina se fesoʻotaʻiga i le va o le laupapa FRDM-IMX93 ma laupapa faʻaoga talafeagai.

3.1 7-inisi Waveshare LCD
O lenei vaega o loʻo faʻamatalaina pe faʻafefea ona faʻafesoʻotaʻi le laupapa FRDM-IMX93 ma le 7-inisi Waveshare LCD e faʻaaoga ai le MIPI DSI interface ma le I2C. O lo'o fa'ama'oti mai ai fo'i suiga e mana'omia ile fa'atulagaina o polokalame e lagolago ai le Waveshare LCD.

3.1.1 So'oga ole MIPI DSI fa'aoga
Ina ia faia se fesoʻotaʻiga i le va o le 7-inisi Waveshare LCD ma le FRDM-IMX93 laupapa e ala i le MIPI DSI interface, faʻamautinoa mea nei:
I le itu LCD:
· FPC cable orientation: Conductive side up and stiffener side down · Faaofi le FPC cable i le LCD's FPC connector I FRDM-IMX93 laupapa itu:
· Fa'atonuga uaea FPC: Itu taumatau ma le itu agavale agavale · Fa'aofi le uaea FPC i le feso'ota'iga FPC o le laupapa (P7)

UM12181
Fa'aoga tusi lesona

O fa'amatalaga uma o lo'o tu'uina atu i totonu o lenei pepa e fa'atatau i fa'aletulafono fa'aletulafono.
Rev. 1.0 — 9 Tesema 2024

NXP Semiconductors

UM12181
FRDM-IMX93 Board Tusi Taiala

Ata 12.FPC uaea feso'ota'iga i le va o le 7-Inch Waveshare LCD ma le FRDM-IMX93
3.1.2 So'oga o le I2C Ata 13 o lo'o fa'aalia ai le feso'ota'iga uaea fa'ailo I2C i le va o le 7-Inch Waveshare LCD ma le FRDM-IMX93.

Ata 13.I2C feso'ota'iga i le va o le 7-Inch Waveshare LCD ma le FRDM-IMX93
3.1.3 Fa'afouina le fa'atulagaina o polokalame
O laasaga nei o loʻo faʻamaoti mai ai pe faʻafefea ona sui le dtb faaletonu i le masani dtb (imx93-11 × 11-frdm-dsi.dtb) e lagolagoina Waveshare LCD.
1. Taofi i le U-Boot 2. Fa'aoga tulafono o lo'o i lalo e sui ai le dtb faaletonu:
$setenv fdtfile imx93-11×11-frdm-dsi.dtb $saveenv $boot

UM12181
Fa'aoga tusi lesona

O fa'amatalaga uma o lo'o tu'uina atu i totonu o lenei pepa e fa'atatau i fa'aletulafono fa'aletulafono.
Rev. 1.0 — 9 Tesema 2024

NXP Semiconductors

UM12181
FRDM-IMX93 Board Tusi Taiala

3.2 5-inisi Tianma LCD
TM050RDH03-41 o se 5 "TFT LCD faʻaaliga ma 800x480 iugafono. O lenei fa'aaliga fa'ale-aganu'u e fa'aogaina se fa'aoga RGB e aunoa ma se pa'i pa'i. O lenei faʻaaliga module e fesoʻotaʻi i le FRDM-IMX93 e ala i le EXPI 40-pin connector (P11).
3.2.1 So'oga i le va o Tianma panel ma adapter board
Ata 14 o loʻo faʻaalia ai le fesoʻotaʻiga FPC i le va o le 5-inch Tianma LCD panel ma le adapter board. Fa'aofi le feso'ota'iga FPC fa'atasi ai ma le itu fa'ata'ita'i i luga (fa'amalo i lalo).

Ata 14.FPC fesoʻotaʻiga i le va o le 5-inisi Tianma LCD panel ma le laupapa faʻapipiʻi
3.2.2 Fesoʻotaʻiga i le va o le laupapa faʻapipiʻi ma le FRDM-IMX93 Plug 5 "Tianma LCD i le FRDM-MIX93 e ala i le EXPI 40-pin connector (P11) e pei ona faʻaalia i le Ata 15

Ata 15.5-inisi Tianma LCD feso'ota'iga ma FRDM-MIX93 e ala ile 40-pin feso'ota'iga

UM12181
Fa'aoga tusi lesona

O fa'amatalaga uma o lo'o tu'uina atu i totonu o lenei pepa e fa'atatau i fa'aletulafono fa'aletulafono.
Rev. 1.0 — 9 Tesema 2024

NXP Semiconductors

UM12181
FRDM-IMX93 Board Tusi Taiala

3.2.3 Fa'afouina le fa'atulagaina o polokalame
O laasaga nei o loʻo faʻamaonia ai pe faʻafefea ona sui le dtb faaletonu i le dtb masani (imx93-11 × 11-frdm-tianma-wvgapanel.dtb) e lagolagoina Tianma LCD.
1. Taofi i le U-Boot 2. Fa'aoga tulafono o lo'o i lalo e sui ai le dtb faaletonu:
$setenv fdtfile imx93-11×11-frdm-tianma-wvga-panel.dtb $saveenv $boot

3.3 meapueata (RPI-CAM-MIPI)
O le RPI-CAM-MIPI faʻapipiʻi faʻapipiʻi o se MIPI-CSI mea pueata module adapter. O le mea fa'apipi'i e fa'avae i luga o le AR0144 CMOS image sensor ma ONSEMI IAS interface e ala i le fa'aletonu, lea e fa'aalia ai le 1/4-inisi 1.0 Mp fa'atasi ai ma le fa'aogaina-pixel array o le 1280 (H) x 800 (V). Ole va'a ole ISP i luga ole va'a e mafai ai ona fa'aoga i le tele o SoCs. O lenei laupapa fesoasoani e feso'ota'i i le laupapa FRDM-IMX93 e ala i le 22-pin / 0.5 mm pitch FPC cable.
3.3.1 So'oga i le va o le RPI-CAM-MIPI ma le FRDM-IMX93
Ata 16 o loʻo faʻaalia ai le fesoʻotaʻiga uaea FPC i le va o le RPI-CAM-MIPI ma le FRDM-IMX93.
I le itu RPI-CAM-MIPI:
· Fa'asinomaga FPC cable: Fa'amalo le itu i luga ma le itu fa'ata'ita'i i lalo · Fa'aofi FPC cable i le RPI-CAM-MIPI FPC so'oga I le itu o le laupapa FRDM-IMX93:
· FPC cable orientation: Conductive itu taumatau ma malo malo itu tauagavale · Faaofi le FPC cable i le FPC connector (P7) o le laupapa

Ata 16.FPC feso'ota'iga i le va o le RPI-CAM-MIPI ma le FRDM-IMX93

UM12181
Fa'aoga tusi lesona

O fa'amatalaga uma o lo'o tu'uina atu i totonu o lenei pepa e fa'atatau i fa'aletulafono fa'aletulafono.
Rev. 1.0 — 9 Tesema 2024

NXP Semiconductors

UM12181
FRDM-IMX93 Board Tusi Taiala

3.3.2 Fa'afouina le fa'atulagaina o polokalame
Ile faaletonu BSP, FRDM-IMX93 lagolago ap1302 + ar0144.
Mo le taimi muamua faʻaaoga, mulimuli i laasaga nei:
· Download ap1302 firmware mai le ONSEMI github, ma toe faaigoa o le ap1302.fw · Kopi le ap1302.fw i le laupapa taulaʻi i lalo o le ala /lib/firmware/imx/camera/ (afai e lē o iai le faila, fai)
a'a@imx93frdm:~# dmesg | grep ap1302 [2.565423]ap1302 mipi2-003c:AP1302 Chip ID o le 0x265 [2.577072]ap1302 mipi 2-003c: AP1302 ua maua [7.477363]mx8-img1302 subdevice: Mx2-img-md003 ua resitalaina: 1-7.513503c (8) [1302]mx2-img-md: faia so'oga [ap003 mipi 2.0-7.988932c] => [mxc-mipi-csi1302]2]ap003 mipi XNUMX-XNUMXc: Uta
firmware manuia.

3.4 Isi laupapa faaopoopo
O loʻo i ai isi laupapa faʻapipiʻi e mafai foi ona galulue ma FRDM-IMX93 e ala i le EXPI 40-pin interface, pei ole MX93AUD-HAT ma le 8MIC-RPI-MX8. Mo le faʻaaogaina o soʻo se laupapa, siaki le faʻasologa ma le faʻatulagaina e fuafua ai le itu o le fesoʻotaʻiga i le va o le FRDM-IMX93 ma le laupapa faʻapipiʻi i luma atu. E le gata i lea, filifili le dtb sa'o file i le U-Boot stage.

Ata 17. laupapa fa'aoga
3.5 Fa'afouina le fa'atulagaina o polokalame
· Ina ia fa'aoga le laupapa MX93AUD-HAT ma le 8MIC-RPI-MX8 fa'atasi pe fa'aoga le laupapa MX93AUD-HAT na'o ia, fa'agasolo tulafono nei ile U-Boot e sui ai le dtb faaletonu: $setenv fdtfile imx93-11×11-frdm-aud-hat.dtb $saveenv $boot
· Mo le fa'aogaina o le laupapa 8MIC-RPI-MX8 na'o ia, fa'atonu tulafono nei ile U-Boot e sui ai le dtb faaletonu: $setenv fdtfile imx93-11×11-frdm-8mic.dtb $saveenv

UM12181
Fa'aoga tusi lesona

O fa'amatalaga uma o lo'o tu'uina atu i totonu o lenei pepa e fa'atatau i fa'aletulafono fa'aletulafono.
Rev. 1.0 — 9 Tesema 2024

NXP Semiconductors

UM12181
FRDM-IMX93 Board Tusi Taiala

$fa'a

4 faʻamatalaga PCB

O le FRDM-IMX93 o loʻo faia faʻatasi ma le 10-layer technology. Ole mea ole FR-4, ma o faʻamatalaga faʻapipiʻi PCB o loʻo faʻamatalaina ile Laulau 24.

Laulau 24. FRDM-IMX93 laupapa fa'aputuina fa'amatalaga

Fa'amatalaga Fa'avae

Kopa (mil)

LUGA

0.7+ Fa'apalapala

–

Dielectric

–

GND02

1.4

–

Dielectric

–

ART03

1.4

–

Dielectric

–

PWR04

1.4

–

Dielectric

–

PWR05

1.4

–

Dielectric

–

ART06

1.4

–

Dielectric

–

GND07

1.4

–

Dielectric

–

ART08

1.4

–

Dielectric

–

GND09

1.4

–

Dielectric

–

LALO

0.7+ Fa'apalapala

Maea: 1.6 mm

Fuafuaina: 71.304 mil

Mea: FR-4

General –

mafiafia dielectric (mil)

–

1.3

2.61

–

8.8

–

8.8

–

8.8

–

2.61

–

1.3

1.811 mm

5 Acronyms

Laulau 25 o lo'o lisi ma fa'amatala ai fa'apuupuu ma fa'apuupuuga o lo'o fa'aogaina i lenei pepa.

Laulau 25.Acronyms Term BGA CAN CSI-2

Fa'amatalaga Fa'asologa o polo Fa'atonu feso'ota'iga a le eria Meapueata fa'asologa fa'asologa 2

UM12181
Fa'aoga tusi lesona

O fa'amatalaga uma o lo'o tu'uina atu i totonu o lenei pepa e fa'atatau i fa'aletulafono fa'aletulafono.
Rev. 1.0 — 9 Tesema 2024

NXP Semiconductors

UM12181
FRDM-IMX93 Board Tusi Taiala

Laulau 25.Acronyms…fa'aauau Terimi DNP DSI eMMC EXPI FD GPIO HS I2C I2S I3C LDO LED MIPI MISO MOSI NGFF PDM PMIC PWM UART USB uSDHC

Fa'amatalaga Aua ne'i fa'atumuina Fa'aali fa'asologa fa'asologa Fa'apipi'i kata multimedia fa'alautele Fa'amatalaga Fa'amatalaga fetuutuunai Fuafuaga fa'atatau lautele Ulufale/fa'aulufale maualuga Saosaoa Feso'ota'i feso'ota'i leo Inter-IC Fa'alelei feso'ota'iga feso'ota'iga va'ava'a fa'amalo maualalo le fa'amalo moli-emitting diode Fe'avea'i atina'e atina'e feso'ota'iga masini fa'aoga pologa Ulufale matai fa'aulufale pologa Fa'aoga o le isi augatupulaga Fa'afuafua fa'asolo Fa'asolo-density Fa'atonuga Fa'asolo-matelega Pulea fa'ateletelega Pulea fa'atasi le va'ava'a. pasi Ultra fa'amautu fa'atonu fa'atekinolosi fa'atonu

6 Fa'amaumauga fa'atatau

Lisi 26 lisi ma fa'amatalaina pepa fa'aopoopo ma punaoa e mafai ona e va'ai i ai mo nisi fa'amatalaga ile laupapa FRDM-IMX93. O nisi o pepa o lo'o lisiina i lalo e mafai ona maua i lalo o se maliega e le fa'ailoaina (NDA). Ina ia talosagaina le avanoa i nei pepa, faʻafesoʻotaʻi lau enisinia talosaga i le lotoifale (FAE) poʻo le sui faʻatau.

Laulau 26. Fa'amaumauga fa'atatau

Pepa

Fa'amatalaga

So'oga / fa'afefea ona maua

i.MX 93 Applications Processor Reference Manual

Fa'amoemoe mo polokalama faakomepiuta ma meafaigaluega

IMX93RM

tagata atiaʻe ma tagata fai polokalame o loʻo manaʻomia

e atiina ae oloa ma i.MX 93 MPU

i.MX 93 Alamanuia Talosaga Processors Pepa Faamatalaga

Tuuina atu faʻamatalaga e uiga i uiga eletise, iloiloga faʻatulagaina meafaigaluega, ma faʻamatalaga oka

IMX93IEC

i.MX93 Taiala Fuafuaga Meafaigaluega

O lenei pepa e fa'amoemoe e fesoasoani i masini inisinia IMX93HDG mamanu ma fa'ata'ita'i a latou i.MX 93 mamanu fa'avae. E maua ai fa'amatalaga e uiga i le fa'atulagaina o laupapa

UM12181
Fa'aoga tusi lesona

O fa'amatalaga uma o lo'o tu'uina atu i totonu o lenei pepa e fa'atatau i fa'aletulafono fa'aletulafono.
Rev. 1.0 — 9 Tesema 2024

NXP Semiconductors

UM12181
FRDM-IMX93 Board Tusi Taiala

Laulau 26. Fa'amaumauga fa'atatau...fa'aauau

Pepa

Fa'amatalaga

fautuaga ma lisi siaki mamanu ina ia mautinoa le pasi muamua manuia ma aloese mai faafitauli o le aumaia o le komiti.

So'oga / fa'afefea ona maua

UM12181
Fa'aoga tusi lesona

O fa'amatalaga uma o lo'o tu'uina atu i totonu o lenei pepa e fa'atatau i fa'aletulafono fa'aletulafono.
Rev. 1.0 — 9 Tesema 2024

NXP Semiconductors

UM12181
FRDM-IMX93 Board Tusi Taiala

7 Fa'amatalaga e uiga i le fa'ailoga puna i totonu o le pepa

O le exampO le code o lo'o fa'aalia i lenei pepa o lo'o i ai le puletaofia ma le laisene BSD-3-Clause:
Puletaofia 2024 NXP Toe tufaina ma fa'aoga ile puna ma fomu fa'alua, fa'atasi pe leai fo'i se suiga, e fa'atagaina pe a fa'amalieina tulaga nei:
1. O le tufatufaina o faʻavae tulafono e tatau ona taofia le faʻasilasilaga i luga o le puletaofia, o le lisi o aiaiga ma le itu ua teʻena.
2. O tufatufaina atu i le binary form e tatau ona toe gaosia le faʻasilasilaga i luga o le puletaofia, lenei lisi o aiaiga ma le itu lea ua teʻena i le pepa ma / poʻo isi mea na saunia ma le tufatufaina.
3. E le mafai ona fa'aogaina le igoa ole tagata e umia le puletaofia po'o le igoa o ana tagata fai sao e fa'amaonia pe fa'alauiloa oloa e maua mai i lenei polokalame e aunoa ma se fa'atagaga tusitusia fa'apitoa.
O LENEI SOFTWARE E TUUINA E LE AU PULE MA FAIGA FAAVAE “PEA UA IAI” MA SOO SE FAAMANATU FAAMANATU POO FAAMANATU, E AOFIA AI, AE LE FAATAATAA I, FAASOLOGA FAAVAE O FAIGA FAAVAE MA FAIGA FAʻAVAE MO SE FAʻAMATALAGA FAʻAALIGA. E LEAI SE MEA E TATAU AI LE UA PUEINA PEA POO IA FAI SAO, MO SO'O SE TU'U, FA'A'O'O'O, FA'AMATALAGA, FA'AMATALAGA, FA'A'OA'OGA, POO FA'A'OA'OGA FA'A'OA'O (E A'OA'O AI, AE LE FAATA'A I, FA'AIGA O Oloa E suitulaga ai, AUAUNAGA; POO FA'AALAAUINA PISINISI) PE'O Ē AE ONA FA'AUGA MA I SO'O SE FA'AMATALAGA O NOFOAIGA, PE I KOKOMETAITA'I, NOFOAIGA FA'AMATALAGA, PO'O LE FA'ASA'OGA (E A'OA'O AI LE FA'AALAPO'O PO'O SE ISI) E ALA MAI I SO'O SE AUALA MAI LE FA'A'OGA O LENEI SOFTWARE, E TU'U I LE FAATUATUA.

8 Toe iloilo talaʻaga

O le Siata 27 o lo'o aoteleina ai suiga i lenei pepa.

Fuafuaga 27. Toe iloiloga tala'aga

ID pepa

Aso fa'amalolo

UM12181 v.1.0

9 Tesema 2024

Fa'amatalaga Fa'asalalauga muamua.

UM12181
Fa'aoga tusi lesona

O fa'amatalaga uma o lo'o tu'uina atu i totonu o lenei pepa e fa'atatau i fa'aletulafono fa'aletulafono.
Rev. 1.0 — 9 Tesema 2024

NXP Semiconductors

UM12181
FRDM-IMX93 Board Tusi Taiala

Fa'amatalaga faaletulafono
Uiga
Fa'ata'ita'iga - O se ata fa'ata'ita'i i luga o se pepa e fa'ailoa mai ai o lo'o i lalo o le toe fa'alotoifale le meaview ma i lalo o le fa'atagaga aloa'ia, e ono i'u ai i suiga po'o fa'aopoopo. NXP Semiconductors e le tuʻuina atu soʻo se faʻamatalaga poʻo se faʻamaonia e uiga i le saʻo poʻo le atoatoa o faʻamatalaga o loʻo aofia i totonu o se ata faataitai o se pepa ma e le tatau ona i ai se noataga mo taunuuga o le faʻaaogaina o ia faʻamatalaga.
Fa'ailoga
Fa'asa'o fa'atapula'aina ma noataga - O fa'amatalaga i totonu o lenei pepa e talitonuina e sa'o ma fa'atuatuaina. Ae ui i lea, e le tuʻuina atu e le NXP Semiconductors soʻo se faʻamatalaga poʻo se faʻamaonia, faʻaalia pe faʻaalia, e uiga i le saʻo poʻo le atoatoa o ia faʻamatalaga ma e leai se noataga mo taunuuga o le faʻaaogaina o ia faʻamatalaga. E leai se matafaioi a le NXP Semiconductors mo mea o loʻo i totonu o lenei pepa pe a tuʻuina atu e se faʻamatalaga faʻamatalaga i fafo atu o le NXP Semiconductors. I se tulaga e le tatau ona noatia le NXP Semiconductors mo soʻo se faʻalavelave faʻafuaseʻi, faʻafuaseʻi, faʻasalaga, faʻapitoa poʻo faʻalavelave faʻaleagaina (e aofia ai - e aunoa ma le faʻatapulaʻaina o tupe mama leiloa, tupe leiloa, faʻalavelave pisinisi, tau e fesoʻotaʻi ma le aveeseina poʻo le suia o soʻo se oloa poʻo tau toe faʻaaogaina) pe e le o ia fa'aleagaina e fa'avae i luga o le tort (e aofia ai le fa'atamala), fa'amaonia, soli o konekarate po'o so'o se isi lava talitonuga fa'aletulafono. E ui lava i so'o se fa'aleagaina e ono fa'atupuina e tagata fa'atau mo so'o se mafua'aga, o le aofa'iga atoa ma le fa'aputuga o noataga a le NXP Semiconductors i tagata fa'atau mo oloa o lo'o fa'amatalaina i totonu e tatau ona fa'atapula'aina e tusa ai ma Tuutuuga ma aiaiga o fa'atauga fa'apisinisi a NXP Semiconductors.
Aia tatau e fai ai suiga - NXP Semiconductors e iai le aia tatau e fai ai suiga i faʻamatalaga o loʻo lomia i totonu o lenei pepa, e aofia ai le faʻatapulaʻaina o faʻamatalaga ma faʻamatalaga o oloa, i soo se taimi ma e aunoa ma se faʻaaliga. O lenei pepa e suitulaga ma suia uma faʻamatalaga na tuʻuina atu aʻo leʻi faʻasalalauina.
Talafeagai mo le faʻaaogaina - NXP Semiconductors oloa e leʻo mamanuina, faʻatagaina pe faʻamaonia ina ia talafeagai mo le faʻaogaina o le ola, faʻalavelave ola poʻo le saogalemu-faigaluega poʻo mea faigaluega, poʻo totonu o talosaga pe a le manuia poʻo le faaletonu o se oloa NXP Semiconductors e mafai ona faʻamoemoeina. e i'u ai i manu'a a le tagata lava ia, maliu po'o meatotino tuga po'o le fa'aleagaina o le si'osi'omaga. NXP Semiconductors ma ana tagata fa'atau oloa e le taliaina se noataga mo le fa'aofiina ma/po'o le fa'aogaina o oloa NXP Semiconductors i ia meafaigaluega po'o talosaga ma o lea fa'aaofia ma/po'o le fa'aogaina e i ai le tagata fa'atau.
Talosaga — Talosaga o lo'o fa'amatalaina ii mo so'o se tasi o nei oloa e mo na'o fa'ata'ita'iga. NXP Semiconductors e leai se fa'amatalaga po'o se fa'amaonia e fa'apea o ia tusi talosaga o le a talafeagai mo le fa'aoga fa'apitoa e aunoa ma se toe su'ega po'o se suiga. O tagata fa'atau e nafa ma le mamanu ma le fa'agaioiga o a latou talosaga ma oloa e fa'aaoga ai NXP Semiconductors oloa, ma NXP Semiconductors e le taliaina se noataga mo so'o se fesoasoani i talosaga po'o tagata fa'atau oloa mamanu. E na'o le tagata fa'atau le matafaioi e fa'amautinoa pe talafeagai ma fetaui le oloa NXP Semiconductors mo talosaga a le tagata fa'atau ma oloa ua fuafuaina, fa'apea fo'i ma le fa'atonuga ma le fa'aoga a le tagata fa'atau lona tolu. E tatau i tagata fa'atau ona tu'uina atu le mamanu talafeagai ma le fa'aogaina o puipuiga e fa'aitiitia ai a'afiaga e feso'ota'i ma a latou talosaga ma oloa. E le talia e le NXP Semiconductors so'o se noataga e feso'ota'i ma so'o se faaletonu, fa'aleagaina, tau po'o fa'afitauli e fa'avae i luga o so'o se vaivaiga po'o fa'aletonu i talosaga po'o oloa a le tagata fa'atau, po'o le talosaga po'o le fa'aogaina e le tagata fa'atau lona tolu. E nafa le tagata fa'atau ma le faia o su'ega talafeagai uma mo talosaga a le tagata fa'atau ma oloa e fa'aaoga ai oloa NXP Semiconductors ina ia 'alofia ai le faaletonu o talosaga ma oloa po'o le talosaga po'o le fa'aogaina e le tagata fa'atau lona tolu. E le talia e le NXP so'o se noataga i lea tulaga.

Tuutuuga ma aiaiga o faʻatauga faʻapisinisi - NXP Semiconductors oloa o loʻo faʻatau atu i lalo o tuutuuga ma aiaiga lautele o faʻatauga faʻatau, e pei ona lomia i le https://www.nxp.com/profile/tuuga, sei vagana ua malilie i se isi itu i se maliega tusitusia aloaia a le tagata lava ia. Afai e fa'ai'uina se maliliega ta'ito'atasi na'o aiaiga ma aiaiga o le maliliega ta'itasi e fa'aaoga. O le NXP Semiconductors o loʻo faʻaalia manino i le faʻaaogaina o tuutuuga ma aiaiga lautele a le tagata faʻatau e tusa ai ma le faʻatauga o oloa NXP Semiconductors e le tagata faʻatau.
Puleaina o oloa auina atu i fafo - O lenei pepa faʻapea foʻi ma mea (s) o loʻo faʻamatalaina iinei e mafai ona noatia i tulafono faatonutonu faʻatau atu. O le auina atu i fafo e ono mana'omia se faatagaga muamua mai pulega agavaa.
Talafeagai mo le fa'aoga i oloa e le o ni ta'avale fa'amaonia - Vagana ua fa'ailoa manino mai i lenei pepa o lenei NXP Semiconductors oloa fa'apitoa o ta'avale agava'a, o le oloa e le talafeagai mo le fa'aogaina o ta'avale. E le agavaa pe fa'ata'ita'iina e tusa ai ma su'ega ta'avale po'o mana'oga fa'aoga. E le talia e le NXP Semiconductors se noataga mo le fa'aofiina ma/po'o le fa'aogaina o oloa fa'apitoa e le o ni ta'avale i masini ta'avale po'o talosaga.
I le tulaga e faʻaaogaina e le tagata faʻatau le oloa mo le faʻatulagaina ma faʻaoga i totonu o taʻavale taʻavale i faʻamatalaga ma tulaga faʻapitoa, e tatau i le tagata faʻatau (a) ona faʻaogaina le oloa e aunoa ma le NXP Semiconductors' warranty o le oloa mo ia taʻavale, faʻaoga ma faʻamatalaga, ma ( e) so'o se taimi lava e fa'aaoga ai e le tagata fa'atau oloa mo talosaga tau ta'avale i tua atu o fa'amatalaga a le NXP Semiconductors, o lea fa'aoga e tatau ona na'o le fa'alavelave a le tagata fa'atau, ma (c) e fa'asala atoatoa e le tagata fa'atau le NXP Semiconductors mo so'o se noataga, fa'aleagaina po'o fa'atauga o oloa e mafua mai i le mamanu ma le fa'aogaina e tagata fa'atau. le oloa mo mea tau taavale i tua atu o le NXP Semiconductors' standard warranty ma NXP Semiconductors' fa'amatalaga o oloa.
Fuafuaga Iloiloga - O lenei oloa iloiloga ua faʻamoemoeina mo naʻo tagata tomai faʻapitoa faʻapitoa, faʻapitoa mo le faʻaogaina i suʻesuʻega ma atinaʻe siosiomaga e faʻafaigofie ai le iloiloga. E le o se oloa ua mae'a, e le o faamoemoe foi e avea ma se vaega o se oloa ua mae'a. So'o se polokalame fa'akomepiuta po'o mea faigaluega fa'akomepiuta e tu'uina atu ma se oloa e iloilo ai e fa'atatau i aiaiga fa'atatau o laisene e fa'atasi ma ia polokalame po'o meafaigaluega fa'akomepiuta.
O lenei oloa iloiloga o lo'o tu'uina atu i luga o se fa'avae "e pei ona i ai" ma "fa'atasi ai ma fa'aletonu uma" mo na'o fa'amoemoega o iloiloga ma e le tatau ona fa'aogaina mo le fa'ailoga oloa po'o le gaosiga. Afai e te filifili e faʻaoga nei oloa suʻesuʻe, e te faia i lou tulaga lamatia ma o lea ua e malie e faʻasaʻo, puipuia ma faʻamaonia le NXP (ma ana paaga uma) mo soʻo se tagi poʻo mea leaga e mafua mai i lou faʻaogaina. O le NXP, o ana paaga ma a latou kamupani faʻatau oloa o loʻo faʻaalia manino le teenaina o tusi saisai uma, pe faʻaalia, faʻamaonia pe faʻatulafonoina, e aofia ai ae le faʻatapulaʻaina i faʻamaoniga faʻamaonia o le leai o se soliga, faʻatauga ma le talafeagai mo se faʻamoemoega faapitoa. O le tulaga lamatia atoa e uiga i le lelei, poʻo le tulaʻi mai i le faʻaaogaina poʻo le faʻatinoga, o lenei oloa iloiloga e tumau pea i le tagata faʻaoga.
E leai se mea e tatau ona noatia le NXP, ana paaga poʻo a latou faʻatau oloa i tagata faʻaoga mo soʻo se faʻapitoa, faʻapitoa, faʻalavelave, faʻasalaga poʻo faʻalavelave faʻafuaseʻi (e aofia ai e aunoa ma le faʻatapulaʻaina o mea faʻaleagaina mo le leiloa o pisinisi, faʻalavelave pisinisi, leiloa o le faʻaaogaina, leiloa o faʻamatalaga poʻo faʻamatalaga, ma mea faapena) e afua mai i le faʻaaogaina poʻo le le mafai ona faʻaaogaina le oloa suʻesuʻe, tusa lava pe faʻavae i luga o le faʻamaonia, faʻamaonia pe leai), fa'amaonia po'o so'o se isi manatu, tusa lava pe fa'ailoa mai i le ono tupu o ia fa'aleagaina.
E ui lava i soʻo se faʻaleagaina e ono faʻatupuina e le tagata faʻaoga mo soʻo se mafuaʻaga (e aofia ai e aunoa ma se faʻatapulaʻaina, faʻaleagaina uma o loʻo taʻua i luga ma faʻaleagaina tuʻusaʻo uma pe lautele), o le noataga atoa a le NXP, o ana paaga ma a latou faʻatau ma le tagata faʻaoga fofo mo mea uma o loʻo taʻua i luga e tatau ona faʻatapulaʻa i mea faʻaleagaina na faʻatupulaia e le tagata faʻaaoga e faʻavae i luga o le faʻalagolagoina o le tagata faʻaaoga e oʻo atu i le tau sili atu o le tagata faʻaoga e faʻatatau i le tau faʻatatauina o le faʻatauga sili atu. (US$5.00). O tapula'a o lo'o ta'ua muamua, fa'ate'aina ma fa'ate'aina e tatau ona fa'aoga i le maualuga maualuga e fa'atagaina e le tulafono fa'atatau, e tusa lava pe fa'aletonu so'o se fofo o lona fa'amoemoe taua ma e le tatau ona fa'aaogaina pe a o'o i le fa'atinoina o le amio le pulea.
HTML lomiga - O se HTML version, pe a maua, o lenei pepa o loʻo tuʻuina atu o se faʻaaloalo. O fa'amatalaga mautinoa o lo'o i totonu o le pepa fa'atatau ile PDF format. Afai ei ai se eseesega i le va o le HTML pepa ma le PDF pepa, o le PDF pepa e ave i ai le faamuamua.

UM12181
Fa'aoga tusi lesona

O fa'amatalaga uma o lo'o tu'uina atu i totonu o lenei pepa e fa'atatau i fa'aletulafono fa'aletulafono.
Rev. 1.0 — 9 Tesema 2024

NXP Semiconductors

UM12181
FRDM-IMX93 Board Tusi Taiala

Fa'aliliuga - O se fa'aliliuga e le fa'aPeretania (fa'aliliuina) o se pepa, e aofia ai fa'amatalaga fa'aletulafono i totonu o lena pepa, e mo na'o fa'amatalaga. O le fa'aliliuga fa'a-Peretania e fa'amalo pe a iai so'o se 'ese'esega i le va o fa'aliliuga ma fa'aliliuga fa'aperetania.
Saogalemu - E malamalama le tagata fa'atau o oloa uma a le NXP e ono a'afia i fa'aletonu e le'i fa'ailoaina pe mafai fo'i ona lagolagoina tulaga fa'amautu po'o fa'amatalaga fa'atasi ma fa'agata iloa. O le tagata fa'atau e nafa ma le mamanu ma le fa'agaioiga o ana talosaga ma oloa i le gasologa o latou olaga e fa'aitiitia ai le a'afiaga o nei fa'aletonu i talosaga ma oloa a tagata fa'atau. O le matafaioi a le tagata fa'atau e fa'alautele atu fo'i i isi tekonolosi matala ma/po'o fa'apitoa e lagolagoina e oloa NXP mo le fa'aoga i talosaga a tagata fa'atau. E le taliaina e le NXP se noataga mo soʻo se faʻafitauli. E tatau i le tagata fa'atau ona siaki e le aunoa ia fa'afouga saogalemu mai le NXP ma tulitatao lelei.
E tatau i le tagata fa'atau oloa ona filifili oloa e iai vaega saogalemu e sili ona fetaui ma tulafono, tulafono faatonutonu, ma tulaga faatonuina o le talosaga fuafuaina ma faia faaiuga sili o le mamanu e uiga i ana oloa ma e na'o ia e nafa ma le tausisia o tulafono uma, tulafono faatonutonu, ma tulaga saogalemu e faatatau i ana oloa, tusa lava pe o soʻo se faʻamatalaga poʻo se lagolago e mafai ona tuʻuina atu e le NXP.
O le NXP o loʻo i ai le Vaega o le Tali atu i le Puipuiga o oloa (PSIRT) (e mafai ona oʻo i le PSIRT@nxp.com) e faʻatautaia le suʻesuʻega, lipoti, ma le faʻamalolo o vaifofo i faʻafitauli o le saogalemu o oloa NXP.

NXP BV - NXP BV e le o se kamupani fa'agaoioia ma e le tufatufaina pe fa'atau atu oloa.
Fa'ailoga Fa'ailoga
Fa'aaliga: O fa'ailoga uma fa'asino, igoa o oloa, igoa tautua, ma fa'ailoga fa'ailoga o mea ia a latou tagata.
NXP - upu fa'ailoga ma logo o fa'ailoga fa'ailoga a NXP BV AMBA, Arm, Arm7, Arm7TDMI, Arm9, Arm11, Artisan, big.LITTLE, Cordio, CoreLink, CoreSight, Cortex, DesignStart, DynamIQ, Jazelle, Keil, Mali, Mbed, Mbed Enabled, NEON, POP, RealView, SecurCore, Socrates, Thumb, TrustZone, ULINK, ULINK2, ULINK-ME, ULINKPLUS, ULINKpro, Vision, Versatile - o fa'ailoga fa'atau ma/po'o fa'ailoga fa'amaufa'ailoga a Arm Limited (po'o ona lala po'o fa'atasi) i le US ma/po'o se isi mea. O tekinolosi fa'afesoota'i e mafai ona puipuia e so'o se pateni po'o pateni uma, puletaofia, mamanu ma mealilo tau fefa'ataua'iga. Ua taofia aia tatau uma.
Bluetooth — o le upu Bluetooth ma logos o fa'ailoga fa'amaufa'ailoga e umia e le Bluetooth SIG, Inc. ma so'o se fa'aogaina o ia fa'ailoga e le NXP Semiconductors o lo'o i lalo ole laisene.

UM12181
Fa'aoga tusi lesona

O fa'amatalaga uma o lo'o tu'uina atu i totonu o lenei pepa e fa'atatau i fa'aletulafono fa'aletulafono.
Rev. 1.0 — 9 Tesema 2024

NXP Semiconductors

UM12181
FRDM-IMX93 Board Tusi Taiala

Mataupu

1 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 2 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.7.1 2.8 2.9 2.10 2.11 2.12 2.13 2.14 2.15 2.16 2.17 2.18 2.19 2.19.1 2.19.2 2.20 3 3.1 3.1.1
3.2.2
3.2.3 3.3 3.3.1
3.3.2 3.4 3.5 4 5 6

FRDM-IMX93 ua sili atuview ………………………………… 2 7 Ata poloka …………………………………………….2 Faiga o le laupapa …………………………………………… 2 8 Mea e aofia ai le pusa o le laupapa …………………………………………….4 Ata o le laupapa …………………………………………… 4 Feso'ota'i ………………………………………………………7 Oomi faamau …………………………………………8 DIP ki …………………………………………….8 LED …………………………………………………… MX9 FRDM-I. Fa'amatalaga o galuega ………………………………………………………93 Sapalai eletise …………………………………………… 9 Uati …………………………………………………….. 10 I10C fa'aoga ……………………………………………. . 13 LPDDR2X i le LPDDR14 femalagaiga ………………… 15 SD card interface ……………………………………………17 eMMC memory ………………………………………… 4 M.17 connector ma Wi-Fi/Bluetooth module ….. 4 Tri-radio module interface ………………………………..4 CAN interface …………………………………………….. 18 SI USB interface …………………………………………………………………………18. ………………………………………………………. 18 Feso'ota'iga HDMI ………………………………………….2 Ethernet …………………………………………………….. 19 Feso'ota'i fa'alautele ………………………………… 20 Fa'amatagofieina …………………………………………….. 23 Feso'ota'iga SWD …………………………………………. 24 USB debug interface ………………………………… 24 Board errata ……………………………………………..25 Galulue ma mea faaopoopo ………………………..26 26-inisi Waveshare LCD ………………………………26 So'oga o le MIPI DSI interface ………….. 27 So'oga I27C …………………………………………..27 Fa'afouina le fa'atulagaina o polokalame ……………………. 28 Tianma LCD 28-inisi …………………………………………7 So'oga i le va o Tianma panel ma adapter board ………………………………………….. 28 So'oga i le va o adapter board ma le FRDM-IMX28 …………………………………………… 2 Fa'afouina le fa'atulagaina o polokalame ……………………. 29 Meapueata module (RPI-CAM-MIPI) …………….. 29 So'oga i le va o le RPI-CAM-MIPI ma le FRDM-IMX5 …………………………………………… 30 Fa'afouina le fa'atulagaina o polokalame ……………………. 30 O isi laupapa faaopoopo …………………………………. 93 Fa'afouga fa'afou le fa'atulagaina o polokalama ……………………. 30 Fa'amatalaga PCB ………………………………….. 31 Acronyms ……………………………………………. 31 Pepa fa'atatau ………………………………… 93

Fa'amatalaga e uiga i le fa'ailoga fa'apogai i totonu o le pepa ……………………………………………………..36 Toe iloilo tala'aga …………………………………………36 Fa'amatalaga faaletulafono ………………………………………….37

Fa'amolemole ia nofouta o fa'asilasilaga taua e uiga i lenei pepa ma oloa (s) o lo'o fa'amatalaina iinei, ua aofia i le vaega 'Fa'amatalaga Fa'aletulafono'.

Ua taofia aia tatau uma.

Mo nisi fa'amatalaga, fa'amolemole asiasi: https://www.nxp.com

Fa'amatalaga fa'amatalaga

Aso fa'amatu'u: 9 Tesema 2024 Fa'amatalaga Fa'amatalaga: UM12181

Pepa / Punaoa

NXP FRDM-IMX93 Komiti Atina'e [pdf] Tusi Taiala
i.MX 93, FRDM-IMX93, UM12181, FRDM-IMX93 Atina'e Komiti, FRDM-IMX93, Komiti Fa'atino, Komiti Fa'atonu

Fa'asinomaga

Tusi Taiala

NXP FRDM-IMX93 Atina'e Komiti Fa'aaogā Tusi Taiala

FRDM-IMX93 Komiti Atina'e

Fa'amatalaga o oloa

Fa'amatalaga:

Fa'atonuga o le Fa'aaogāina o Mea:

1. Fa'atonuga ma Fa'atonuga:

2. Meafaigaluega Meafaigaluega I Lugaview:

3. Fa'aoga Taiala:

Fesili e Fai soo (FAQ):

Q: O a uiga autu o le laupapa FRDM-IMX93?

Q: E mafai faapefea ona ou faʻafesoʻotaʻi peripherals i le laupapa FRDM-IMX93?

Pepa / Punaoa

Fa'asinomaga

Tuu se faamatalaga

Fa'aleaogaina le tali