Product Overview
The ACTIVESHOP JD700 is a high-quality, compact, and modernly designed milling machine. It features a clear and readable control panel, intuitive operation, offering excellent working possibilities for both experienced users and beginners. The drill bit head is equipped with a TWIST-LOCK bit holder, allowing for single-step bit changes. Control is available via manual operation or foot pedal.
Technical Data
- Power: 35 W
- Power Supply: 220-230 V, 50-60 Hz
- Design: Ergonomic
- Rotation: Clockwise and Counter-clockwise
- Controls: On/Off switch and speed regulation located on the power unit/base.
- Speed: Infinitely adjustable from 0-30,000 RPM.
- Handpiece: TWIST-LOCK handle (single-step bit change).
- Warranty: 12 months.
- Available Colors: White, Black, Violet.
Important Note on Usage
This equipment may be used by children aged 8 years and above, and by persons with reduced physical or mental capabilities, or with insufficient experience and knowledge of the equipment, provided that supervision or instruction is given for safe use of the equipment to understand the associated risks. Children must not perform cleaning or maintenance of the equipment without supervision.
Drill Bit Installation
Follow these steps to install a drill bit:
- Ensure the milling machine is not connected to the power supply.
- Connect the drill bit head to the selected milling machine.
- To change the bit, ensure the head is not operating.
- Turn the collar counter-clockwise until you hear the characteristic "click" sound.
- Insert the desired drill bit into the head.
- To secure the collet, simply turn the collar clockwise until the aforementioned "click" is heard.
Diagrams show the handpiece, the collet being opened, a bit being inserted, and the collet being closed to secure the bit.
Caution: To remove the drill bit, follow the same procedure as when changing the bit.
Attention: Do not operate the milling machine motor if the bit holder is in the open position and there is no bit in the head (this can damage or burn the machine). Remember that after finishing work, the bit holder must always be clamped or secured with a stopper.
Machine Setup
- Set up the device in a work area that is not excessively humid, hot, or dirty.
- Connect the head cable connector to the front of the machine.
- Install the correct drill bit according to the instructions described in the drill bit installation guide.
- After changing the bit, ensure the collet clamps are securely closed with the bit.
- Connect the power plug, then turn on the milling machine.
- After finishing the milling and cleaning, it is recommended that the bit always be placed in the handpiece (drill bit head).
- When you have finished your work, always unplug the power cord from the socket or interrupt the power supply; reducing the speed to 0 does not mean the drill is turned off.
Starting the Milling Machine
- Connect the drill to the power supply.
- Turn on the milling machine using the appropriate button.
- Select the rotation direction (left or right).
- Increase the revolutions to start the head.
Maintenance
Metal, stone, and diamond bits can be sterilized in a sterilizer. Felt bits and brushes should be cleaned with disinfectant.
Recommendations
- Remember that you must never drop the drill or handpiece, as this will damage the ball bearings and affect the motor's lifespan.
- Do not allow water or other liquids to enter the device.
- Each time you change the bit, turn off the router.
- Never change bits while the milling machine is running; the milling machine must be turned off to change bits.
- Connect the drill to the socket only after ensuring all cables are installed correctly and safely.
- We recommend using the machine only for professional purposes.
- The foot pedal switch cable connector must be securely connected to the back of the machine.
- Ensure that the bit you wish to use is not bent, asymmetrical, or damaged. Always use standard bits.
Note: Unlocking the handle during operation will damage the machine. Changing bits while the motor is running damages the clutch. These damages are not covered by warranty. Bits must be changed in the open collet position (unlocked), and the milling machine must be turned off during this time.
Troubleshooting
Milling machine does not turn on:
- Check if it is plugged in - connect the milling machine to the power supply.
- Check if the milling machine is switched on - turn on the milling machine.
- Check if the hand/foot switch is in the "Hand" position.
- Check if the handpiece cable is damaged - replace the handpiece cable (available from Activeshop).
- Check if the power cable is damaged - contact Activeshop service.
- Check if the voltage selector switch is set to 220 V. If not, and the router is connected, the router is damaged - contact Activeshop service for paid repair.
Handpiece is overheating:
- Check if the Twist-Lock is properly closed.
Attention
Do not lubricate the handpieces. Do not disinfect with excessive amounts of liquid. Water or disinfectant entering the handpiece can damage it. Clean dust from the handpiece before possible disinfection. It is recommended to maintain the handpiece using dedicated care products.
Safety Precautions
- The device is professional equipment intended for use in beauty salons. Use of the device only by qualified cosmetic personnel allows for avoidance of adverse effects during the procedure.
- The device must not be disassembled or attempted to be used for purposes other than those specified in this manual. All maintenance and repairs must be performed only by an authorized service technician (ACTIVESHOP Ltd. company).
- Do not install or use the device near liquids, in wet places, or with wet hands to prevent liquids from entering the device.
- Immediately disconnect the device from the socket and contact the authorized service provided by ACTIVESHOP Sp. z o.o. in the following cases:
- A. Liquid has entered the device.
- B. The device emits an unusual smell, smoke, or produces unusual noises.
- C. The power cable is damaged.
- D. The device has tipped over or its casing is damaged.
- Do not place any objects on the cables. Do not place the device in locations where someone might step on the power cable.
- For safety reasons, unplug the power cord from the socket every time you finish working with the device.
- Do not insert anything into the device openings. If a foreign object enters an opening, unplug the cable and contact the distributor or manufacturer.
- Do not place the device on an unstable trolley, shelf, or vehicle. The device may be damaged if it falls.
- To ensure the fixed service life of the device, it is recommended to observe a one-minute interval between switching it on and off repeatedly.
- The power supply must comply with the specifications indicated on the nameplate. Otherwise, there is a risk that the device may not function correctly, be damaged, or burn out.
Caution
- If the power cord is damaged or other operational malfunctions occur, contact an authorized service center to avoid hazards.
- This device may be used by children aged 8 years and above, and persons with reduced physical and mental abilities, or with insufficient experience and knowledge of the equipment, provided that supervision or instructions on the safe use of the equipment are provided, so that the associated risks are understood.
- The equipment is not intended for play by children. Do not allow children to play with the device.
- Do not leave the device unattended if children or persons unfamiliar with the use of the device are nearby.
- This electrical device is not a toy. Incorrect use or contact with the electrical device can endanger health or cause death, therefore the device must be used and stored in a place inaccessible to children.
Device Disposal
Dispose of used electrical devices, accessories, and packaging at recycling centers in accordance with environmental protection principles. Electrical devices must not be disposed of in household waste containers. Comply with regulations for the disposal of such equipment. To protect the environment, in accordance with Directive 2012/19/EU on waste electrical and electronic equipment, used electrical and electronic equipment should be collected separately and then handed over to collection points for used electrical equipment.
Used and old devices contain fully recyclable components, so they must be handed over for recycling. Therefore, they must be handed over to appropriate collection points, or can be handed over to ACTIVESHOP Ltd.
Storage and Transport
The device must be transported at temperatures from (-)20°C to (+)40°C only in its original packaging. The device should be stored in a well-ventilated room where the relative humidity does not exceed 90%. Operating temperature is from (+)10°C to (+)40°C. During storage and transport, the device must not be thrown or dropped, subjected to mechanical shocks, or atmospheric influences.
