ACTIVESHOP Sprint 48

Product Overview

The ACTIVESHOP Sprint 48 is a professional nail drill designed for cosmetic salons. It features high-quality construction, compact dimensions, and a modern design. The drill offers a clear and intuitive control panel, providing excellent operational capabilities for both experienced and beginner users. The milling head achieves speeds from 0 to 30,000 RPM. The cutting head is equipped with a TWIST-LOCK head lock, allowing for single-handed bit changes.

NOTE: Changing the voltage to 110V will cause permanent and irreversible damage to the machine.

Specifications

The drill's control panel and components are detailed below:

• [Item 1]: Speed control knob
• [Item 2]: Speed switch (for clockwise and counter-clockwise rotation)
• [Item 3]: Handpiece socket
• [Item 4]: On/Off switch
• [Item 5]: Foot pedal / manual switch
• [Item 6]: Foot pedal socket
• [Item 7]: Power cord
• [Item 8]: Voltage switch (110/220V)
• [Item 9]: Milling handpiece
• [Item 10]: TWIST-LOCK switch
• [Item 11]: Safety pin for the drill bit socket
• [Item 12]: Foot pedal

Operating the Drill

CAUTION: Unlocking the handle during operation will damage the machine. Changing bits while the motor is running will damage the clutch. This damage is not covered by warranty. Bits must be changed with the handle in the unlocked position, and the drill must be switched off during this time.

1. To prepare the drill, plug the appropriate adapter into an electrical socket.
2. Connect the handpiece to the 3-pin socket.
3. To change the bit:
   • A. Hold the handpiece in your hand to open the drill bit jaws. Turn the rotating ring clockwise until you hear a "click" and the indicator is aligned with the open lock symbol.
   • B. Remove the test rod.
   • C. Insert the desired bit.
   • D. Similar to step A, to close the drill bit jaws, turn the rotating ring counter-clockwise until you hear a "click" and the indicator is aligned with the closed lock symbol.
4. Turn on the drill and then use the start/pause button to gradually set the drilling speed.
5. Change rotation direction: forward/reverse.

NOTE!!! Do not soak the handpieces. Do not disinfect with excessive amounts of liquid. Water or disinfectant that gets inside the handpiece can damage it. Remove dust from the handpiece before any disinfection. It is recommended to maintain the handpiece with a suitable maintenance product.

CAUTION! The handpiece must be cleaned and protected from dust. Warranty claims will not be accepted due to improper use or dust damage to the handpiece.

ATTENTION!!! The jaw opening mechanism may offer greater resistance when the bit is not in the chuck. This is normal and is due to the head's construction.

Technical Data

• Power supply: 220-240 V, 50-60 Hz
• Ergonomic housing
• Right and left rotation capability
• On/Off switch and speed control located on the base
• Smooth speed adjustment
• Handle with a twist lock mechanism (for changing bits)
• Bit diameter: 2.32 mm
• Power output: 35W
• Base weight: 780g
• Handpiece weight: 160g
• The drill is available in white, black, and silver colors.

Dimensions

Basic Problems and Solutions

Drill Not Turning On

• Check if it is plugged into the mains - connect the drill to the power source.
• Check if the drill is switched on - turn on the drill ([Item 9] in the diagram).
• Check if the handpiece cable is damaged - replace the handpiece cable (available at Activeshop).
• Check if the power cord is damaged - contact the Activeshop service department.

Handpiece Overheating

• Check if the Twist-Lock is properly closed.

CAUTION!!! The bit must be changed when the drill is switched OFF using the switch ([Item 9] in the diagram). Reducing the speed ([Item 4] in the diagram) to minimum does not turn off the drill, but only reduces its speed to a level not visible to the naked eye. Changing the bit on a running drill at minimum speed can cause the handpiece to overheat and subsequently be damaged (for which warranty does not apply).

Safety Precautions

1. The appliance is a professional device intended for use in cosmetic salons. Operation of the device only by qualified cosmetic personnel will prevent undesirable consequences during treatment.
2. The appliance must not be disassembled or attempted to be used for purposes other than those stated in this manual. All service operations and repairs must be performed only by an authorized service technician (ACTIVESHOP Sp. z o.o.).
3. Do not install or use the appliance near liquids, in wet areas, or with wet hands to prevent liquids from entering the appliance.
4. In the following cases, immediately unplug the appliance from the socket and contact the authorized service center provided by ACTIVESHOP s.r.o:
   • a) liquid has entered the appliance,
   • b) the appliance emits an unusual smell, smoke, or makes unusual noises,
   • c) the power cord has been damaged,
   • d) the appliance has been tipped over or its casing has been damaged.
5. Do not place any objects on the cables. Do not install the appliance in places where someone might step on the power cord.
6. For safety reasons, always unplug the power cord from the socket when you finish working with the appliance.
7. Do not insert anything into the appliance's openings. If a foreign object enters an opening, unplug the cable and contact the distributor or manufacturer.
8. Do not place the appliance on an unstable trolley, shelf, or vehicle. The appliance may be damaged if it falls.
9. To ensure the appliance's long service life, it is recommended to wait one minute between pressing the power button (between turning on and off, and vice versa).
10. The power supply must comply with the specifications listed on the type plate. Otherwise, there is a risk of improper operation, damage, or even burns to the appliance.

WARNING:

1. In case of damage to the power cord or other faults, contact an authorized service center to prevent any danger.
2. This appliance may be used by children aged 8 years and older, and by persons with reduced physical and mental capabilities, and persons with insufficient experience and knowledge of the device, if supervision is provided or they have been instructed on how to use the device in a safe manner, so that they understand the associated risks.
3. The appliance is not intended for children to play with. Do not allow children to play with the appliance.
4. Do not leave the appliance unattended when children or persons without sufficient knowledge of the appliance's use are nearby.
5. This electrical appliance is not a toy. Improper use or contact with the electrical appliance can pose a risk to health or lead to death, therefore the appliance should be used and stored out of reach of children.

Disposal of the Device

Dispose of used electrical appliances, accessories, and packaging at recycling centers in accordance with environmental protection principles. Electrical appliances should not be disposed of in household waste bins. Follow the rules for the disposal of this type of equipment.

In order to protect the environment, in accordance with Directive 2012/19/ES on waste electrical and electronic equipment, used electrical appliances must be collected separately and handed over at collection points for waste electrical and electronic equipment.

Discarded and old appliances contain fully recyclable components and should therefore be handed over for recycling. They should be handed over at appropriate collection points, as well as to ACTIVESHOP s.r.o.

Storage and Transport

The appliance should be transported at temperatures ranging from -20°C to +50°C, only in its original packaging. The device should be stored in a well-ventilated room with a relative humidity of no more than 75%. Operating temperature is from +10°C to +40°C. During storage and transport processes, the device must not be thrown or dropped, and must not be exposed to mechanical shocks or atmospheric influences.