ACTIVESHOP MARATHON N2 FREESPINK User Manual

Introduction

• The device must be used in a dry, enclosed space.
• Do not drop the milling machine, as it can damage the bearings, affecting the motor's lifespan.
• Do not allow liquids to enter the device.
• After changing the bit, ensure the handle is properly closed.
• Do not open the handle while the machine is running.
• When work is finished and the cutting bit is cleaned, place it back in the handle.
• Always unplug the device from the socket when you have finished working.
• For professional use only.
• The main cable plug must be connected to the front of the device.
• The foot switch cable plug must be securely connected to the rear of the machine's housing.
• Connect the router to the socket only after ensuring all cables are correctly and safely installed.

Before connecting the machine, check that the voltage selector switch is set to 220V. Setting the device to 110V will cause it to burn out.

Technical Specifications

Specifications and Component Description

The device features a main housing with various controls and connection ports. The main unit is white with pink accents.

• 1. Machine housing
• 2. Speed control knob
• 3. Mode switch: manual/foot
• 4. Direction switch: forward/reverse
• 5. On/off button
• 6. Indicator light
• 7. Overload indicator light
• 8. Motor connection port
• 9. Foot pedal connection port
• 10. Foot pedal switch: on/off
• 11. Power cable
• 12. Input voltage switch

Operation Modes

Manual Operation

1. Turn on the device.
2. Ensure the hand/foot pedal switch is set to the "Hand" position.
3. Set the desired bit speed using the selection dial.
4. Press the forward/reverse switch to change the bit's rotation direction.

Foot Operation

1. Turn on the device.
2. Ensure the hand/foot mode switch is set to the "Foot" position.
3. Use the selection dial to set the desired bit speed.
4. In foot control mode, the bit operates within the set speed range.

Inserting/Removing Cutting Tool

1. Turn off the router using the power button.
2. Turn the chuck clockwise until you hear a characteristic "click", then pull out the bit.
3. To secure the bit, turn the chuck counter-clockwise until you hear a "click".
4. Keep the chuck clean before changing bits.
5. Ensure the bit you intend to use is not bent, asymmetrical, or damaged. Always use standard bits.

Caution: Unlocking the workpiece during operation damages the machine. Changing bits while the motor is running damages the chuck. Such damage is not covered by warranty. Bits must be changed with the handle in the unlocked position, and the bit must be off at that time.

Safety System: Overload/Overheating Function

To protect the milling machine from overheating (due to bearing failure, large bit diameter, or overload), the temperature sensor will cut off power. The overload indicator light will turn red. The milling machine will automatically shut off after 5 seconds if overheated. Turn the device off and then on again after about 30 seconds.

Recommended Rotation Speeds by Bit Type

Attention! The head must be cleaned and protected from dust. Claims will not be accepted for damage to the head due to improper use or dust.

Troubleshooting

Milling machine does not turn on:

• Check connection: Connect the mill to the power outlet.
• Check if the mill is turned on: Use the on/off switch (item 5).
• Check if the hand/foot switch (item 3) is set to "Hand".
• Check if the main cable is damaged: Replace the main cable (available from Activeshop).
• Check if the power cord is damaged: Contact Activeshop service.
• Check if the voltage selector switch (item 12) is set to 220V. If not, and the router is connected, the router is damaged. Contact Activeshop service for paid repair.

Head has overheated:

• Check if the Twist-Lock is properly closed.

Caution: Bits must be replaced after the mill is turned off using the switch (item 5). Turning the speed control potentiometer (item 2) to minimum does not turn off the mill, only reduces speed. Changing bits at minimum speed while the mill is running can cause the bit head to overheat, resulting in damage (not covered by warranty).

Caution!!! Do not soak the head. Do not disinfect with excessive liquid. Water or disinfectant entering the head can damage it. Remove dust before possible disinfection. It is recommended to maintain the head with special care products.

Safety Measures

1. This is a professional device intended for use in beauty salons. Use by qualified personnel avoids adverse effects during treatment.
2. Do not disassemble the device or attempt to use it for purposes other than those specified in this user manual. All maintenance and repair work must be performed only by an authorized service technician (ACTIVESHOP Sp. z o.o.).
3. Do not install or use the device near liquids, wet areas, or with wet hands to prevent liquid ingress into the device.
4. Immediately unplug the device from the socket and contact an authorized service company (ACTIVESHOP Sp. z o.o.) in the following cases: a) liquid has entered the device, b) the device emits a strange odor, smoke, or makes unusual noise, c) the power cord is damaged, d) the device has fallen over or its housing is damaged.
5. Do not place any objects on the cords. Do not install the device in a location where someone might step on the power cord.
6. For safety, unplug the power cord from the socket every time you finish working with the device.
7. Do not insert anything into the device openings. If foreign objects enter an opening, unplug the cord and contact the dealer or manufacturer.
8. Do not place the device on an unstable trolley, shelf, or vehicle. The device may be damaged if it falls.
9. To ensure the device's longevity, it is recommended to wait one minute between turning the power button on and off (and vice versa).
10. The power supply must meet the specifications on the data plate. Otherwise, there is a risk that the device will not work correctly, get damaged, or even burn out.

Caution:

1. In case of power cord damage or other faults, contact an authorized service center to avoid any danger.
2. This device can be used by children aged 8 and above, and persons with reduced physical and mental capabilities or lack of experience and knowledge, provided they receive supervision or instructions for safe use and understand the associated risks.
3. Devices are not toys. Do not allow children to play with the device.
4. Do not leave the device unattended if children or persons unfamiliar with its use are nearby.
5. This electrical device is not a toy. Improper use or contact with the electrical device can endanger health or cause death, therefore the device must be used and stored out of reach of children.

Device Disposal

Dispose of used electrical equipment, accessories, and packaging at recycling centers in accordance with environmental protection principles. Electrical devices must not be disposed of in household waste containers. Follow the regulations for this type of equipment disposal. To protect the environment according to Directive 2012/19/EU on waste electrical and electronic equipment, used electrical equipment must be collected separately and handed over to collection points for waste electrical and electronic equipment. Discarded and old devices contain fully recyclable components and should therefore be sent for recycling. Thus, they should be handed over to appropriate collection points and also ACTIVESHOP Ltd.

Storage and Transport

The device must be transported at temperatures from (-) 20°C to (+) 40°C only in original packaging. The device must be stored in a well-ventilated room where the relative humidity does not exceed 90%. The operating temperature is between (+) 10°C and (+) 40°C. During storage and transport, the device must not be dropped or thrown down, and must not come into contact with mechanical shocks or weather conditions.