CORSTON ARCHITECTURAL DETAIL
Baylis Spotlights
INSTRUCTIONS
Single spotlight
Included
- Spotlight x1
- Anchor x2 [wall anchor]
- Screw x2 [screw]
- Hex key x1 [hex key]
Tools You'll Need
- Drill [drill]
- 6mm drill bit [drill bit]
- 20mm drill bit [drill bit]
- Crosshead screwdriver [screwdriver]
Important Notes
Before installation, the power supply should be isolated at the consumer unit circuit breaker. Check that the power is off.
These products must be installed by a qualified electrician in accordance with the latest building regulations.
We include 300mm of additional cable and a small terminal box to assist with installation. You'll need space, such as a void above the ceiling or behind the wall, to house these parts.
Installation Steps
Step 1: Drilling Holes
Drill the 20mm hole for the wires and the two 6mm holes for the plastic anchors. Refer to the template on page 5 for precise placement.
Diagram Description: Diagram shows drilling a 20mm hole for wires and two 6mm holes for anchors.
Step 2: Mounting Plate Installation
Use the screws and anchors provided to attach the mounting plate to the ceiling or wall.
Diagram Description: Diagram shows the mounting plate being attached to the ceiling or wall using screws and anchors.
Step 3: Wiring and Cover Attachment
Using the terminal box provided, connect the live (brown) and neutral (blue) wires. Tuck the wires and the terminal box into the void. Push the brass cover over the mounting plate.
Diagram Description: Diagram illustrates connecting live (brown) and neutral (blue) wires in a terminal box, tucking it into a void, and fitting the main spotlight body.
Step 4: Securing the Spotlight
When the cover is flush with the ceiling or wall, tighten the two grub screws to secure the spotlight.
Diagram Description: Diagram shows tightening two grub screws to secure the spotlight when the cover is flush.
Step 5: Bulb Installation and Testing
Insert a 50mm GU10 bulb (Arthur or Chester) or a 35mm bulb (Court) into the shade and test the light to make sure the wiring is correct.
Diagram Description: Diagram depicts inserting a bulb into the spotlight shade and testing the light.
Template for Drilling
Print this template on A4 paper for accurate hole placement.
Diagram Description: Drilling template with a 20mm hole and two 6mm holes, showing dimensions for spacing.
Double spotlight
Included
- Spotlight x1 (unit with two heads)
- Anchor x2 [wall anchor]
- Screw x2 [screw]
- Hex key x1 [hex key]
Tools You'll Need
- Drill [drill]
- 6mm drill bit [drill bit]
- 20mm drill bit [drill bit]
- Crosshead screwdriver [screwdriver]
Important Notes
Before installation, the power supply should be isolated at the consumer unit circuit breaker. Check that the power is off.
These products must be installed by a qualified electrician in accordance with the latest building regulations.
We include 300mm of additional cable and a small terminal box to assist with installation. You'll need space, such as a void above the ceiling or behind the wall, to house these parts.
Installation Steps
Step 1: Drilling Holes
Drill the 20mm hole for the wires and the four 6mm holes for the plastic anchors. Refer to the template on page 8 for precise placement.
Diagram Description: Diagram shows drilling a 20mm hole for wires and four 6mm holes for anchors.
Step 2: Mounting Plate Installation
Use the four screws and anchors provided to attach the mounting plate to the ceiling or wall.
Diagram Description: Diagram shows the mounting plate for the double spotlight being attached to the ceiling or wall using screws and anchors.
Step 3: Wiring and Cover Attachment
Using the terminal box provided, connect the live (brown) and neutral (blue) wires. Tuck the wires and the terminal box into the void. Push the brass cover over the mounting plate.
Diagram Description: Diagram illustrates connecting live (brown) and neutral (blue) wires in a terminal box, tucking it into a void, and fitting the main double spotlight body.
Step 4: Securing the Spotlight
When the cover is flush with the ceiling or wall, tighten the four grub screws to secure the spotlight.
Diagram Description: Diagram shows tightening four grub screws to secure the double spotlight when the cover is flush.
Step 5: Bulb Installation and Testing
Insert 50mm GU10 bulbs (Arthur or Chester) or 35mm bulbs (Court) into the shades and test the light to make sure the wiring is correct.
Diagram Description: Diagram depicts inserting bulbs into the double spotlight shades and testing the light.
Template for Drilling
Print this template on A4 paper for accurate hole placement.
Diagram Description: Drilling template with a 20mm hole and four 6mm holes, showing dimensions for spacing.
