Corston Picture Lights

Included Parts

The following components are included with the Harrow Picture Light:

• Harrow picture light x1
• Fixing bracket x1
• Wall mount x1
• Screw x2
• Driver x1
• Cable tie x1
• Foam raiser x2
• Grub screw x2
• Wall screw x2
• Anchor x2
• Hex key x1

Tools You'll Need

The following tools are recommended for installation:

• Drill
• 6mm drill bit
• Flathead screwdriver
• Crosshead screwdriver

Specifications

*Unless used with a compatible third-party dimmable driver.

Warning: Never plug a picture light into the mains electricity without a driver. Doing so could cause irreparable damage to your product.

Installation Steps

1. Loosen the lower grub screw to release the inner cable.

   [Diagram: Shows loosening a grub screw on the picture light stem to allow cable movement.]

2. Attach the shade to the stem and insert the upper grub screws to fix in place. Tighten all grub screws.

   [Diagram: Shows attaching the light shade to the stem and securing it with grub screws.]

3. Use the cable tie to attach the driver to the wall mount and connect the driver.

   [Diagram: Shows a cable tie securing the driver unit to the wall mount bracket, with driver connections visible.]

4. Attach the picture light to the wall mount using the fixing bracket.

   [Diagram: Shows the picture light assembly being connected to the wall mount via the fixing bracket.]

5. Use the screws and anchors provided to fix the light to the wall.

   [Diagram: Shows screws and wall anchors being used to secure the wall mount to the wall.]

6. Connect power to the driver.

   [Diagram: Shows the power cable being connected to the driver unit.]

7. Loosen the fixing bracket screws to adjust the light's height.

   [Diagram: Shows adjusting the vertical position of the light by loosening screws on the fixing bracket.]

8. Optional: add foam raisers to the rear bottom corners of the frame.

   [Diagram: Shows foam pads being attached to the back of a picture frame.]

9. Hang your chosen frame on the built-in hook on the wall mount.

   [Diagram: Shows a picture frame being hung on a hook attached to the wall mount.]

Included Parts

The following components are included with the Taylor Picture Light:

• Taylor picture light x1
• Hex key x1
• Back box x1
• Back plate x1
• Driver x1
• Grub screw x2
• Flathead screw x2

Tools You'll Need

The following tools are recommended for installation:

• Drill
• 71mm hole saw (bespoke)
• Flathead screwdriver
• Crosshead screwdriver

Specifications

*Unless used with a compatible third-party dimmable driver.

Warning: Never plug a picture light into the mains electricity without a driver. Doing so could cause irreparable damage to your product.

Installation Steps

1. Drill a 71mm hole using the provided hole saw.

   [Diagram: Shows drilling a hole in the wall with a drill and hole saw.]

2. Before installing, rotate the back box 90 degrees anticlockwise so that the logo is sideways.

   [Diagram: Shows rotating a circular back box 90 degrees so the 'Corston' logo is horizontal.]

3. Fit the back box into your wall, ensuring it is still rotated 90 degrees. The back box should be flush with the wall. Screw in place.

   [Diagram: Shows inserting the rotated back box into the drilled hole and securing it with screws.]

4. Attach the plate to the back box.

   [Diagram: Shows a mounting plate being attached to the installed back box.]

5. Attach the shade to the stem using the grub screws.

   [Diagram: Shows the light shade being connected to the stem and secured with grub screws.]

6. Connect the driver to the power supply.

   [Diagram: Shows the driver unit connected to the power source.]

7. Mount the light onto the back plate.

   [Diagram: Shows the assembled light fixture being attached to the wall plate.]