Vera Dream Bed and Wings Assembly Instructions
Vendor: Living Spaces
Vendor Code: V-005852
Vendor Collection: VERA DREAM NON STORAGE / VERA DREAM
Vera Dream Bed Assembly (Non Storage)
Parts List
| Item | Description | Quantity |
|---|---|---|
| 1 | VERA DREAM HEADBOARD | (Qty: 1) |
| 2 | VERA DREAM RAILS/SLATS | (Qty: 1) |
| 3 | VERA DREAM FOOTBOARD | (Qty: 1) |
Hardware Included
Hardware bag included in side rails and slat box with red ribbon to be located.
| ID | Description | Quantity |
|---|---|---|
| A | 5/16-18X1" SCREW BUTTON HEAD CAP | (Qty: 8) |
| B | WASHER 5/16 PLAIN | (Qty: 8) |
| C | 3/16 SHORT ARM HEX KEY | (Qty: 2) |
| D | 5/16-18X1 1/2" SCREW BUTTON HEAD CAP | (Qty: 2) |
Assembly Steps
Step 1: Attach Side Rails to Headboard
Attach the side rails (Item 2) to the headboard (Item 1) using the provided Hex Key (C), 4 Screws (A), and 4 Washers (B).
Diagram Description: Shows the headboard (Item 1) standing upright. Side rails (Item 2) are positioned to attach to the sides of the headboard. Fasteners indicated are Screws (A) and Washers (B), secured with a Hex Key (C). A hardware bag is also depicted. Estimated assembly time: (Est. Time: 30 mins).
Step 2: Attach Footboard to Side Rails
Attach the footboard (Item 3) to the side rails (Item 2) using the provided Hex Key (C), 4 Screws (A), and 4 Washers (B).
Diagram Description: Illustrates the footboard (Item 3) being attached to the lower ends of the side rails (Item 2). Fasteners shown are Screws (A) and Washers (B), secured with a Hex Key (C).
Step 3: Attach Support Legs to Center Slat
Attach the support legs, which include levelers, to the center slat. Adjust the levers on the bottom of the support legs as necessary for stability.
Note on Support Legs Quantity:
- CENTER QUEEN BED: 1 Quantity (5 Support legs)
- CENTER CK BED: 1 Quantity (5 Support legs)
- CENTER EK BED: 2 Quantity (10 Support legs)
Diagram Description: Depicts support legs, each with a leveler at the bottom, being attached to a central slat. Arrows indicate the direction of attachment. A 'TURN RIGHT' instruction is shown, likely for adjusting the leveler.
Step 4: Place U-shaped Panel
Place the U-shaped panel piece from top to bottom into the corresponding slot on the bed frame.
Diagram Description: Shows a U-shaped panel being inserted vertically into a slot on the bed frame structure.
Step 5: Unroll Slats
Unroll the slats onto the center slat, starting at the footboard and ending at the headboard.
Diagram Description: Illustrates a series of wooden slats being unrolled and laid across the bed frame, starting from the footboard end and extending towards the headboard end.
Step 6: Verify Slat Installation
Verify that the slats are installed properly and that the legs are perpendicular to the floor for full support.
Diagram Description: A final view of the assembled bed frame, showing the slats in place and the support legs resting on the floor, indicating perpendicularity for stability.
Vera Dream Wings Assembly
Parts List
| Item | Description | Quantity |
|---|---|---|
| 1 | VERA DREAM WINGS | (Qty: 2) |
Hardware Included
Hardware bag included below with red ribbon to be located.
| ID | Description | Quantity |
|---|---|---|
| A | SLOT BRACKET | (Qty: 4) |
| B | CORNER BRACKET | (Qty: 2) |
| C | 5/16-18X1-1/4" SCREW BUTTON HEAD CAP | (Qty: 10) |
| D | WASHER 5/16 PLAIN | (Qty: 10) |
| E | 3/16 SHORT ARM HEX KEY | (Qty: 2) |
Assembly Steps
Step 1: Attach Brackets (Left Side)
Attach brackets (A & B) facing the left side to the wing, at the end of the slot. Use the provided Hex Key (E), Screws (C), and Washers (D).
Diagram Description: Shows a wing component. Brackets labeled 'A' (Slot Bracket) and 'B' (Corner Bracket) are being attached to the left side of the wing using Screws (C) and Washers (D), secured with a Hex Key (E).
Step 2: Attach Brackets (Right Side)
Attach brackets (A & B) facing the right side to the wing, at the end of the slot. Use the provided Hex Key (E), Screws (C), and Washers (D).
Diagram Description: Similar to Step 1, but shows Brackets 'A' and 'B' being attached to the right side of the wing using Screws (C) and Washers (D), secured with a Hex Key (E).
Step 3: Position Bed for Wing Attachment
Raise the bed frame to position it inside the side rail of the wing bracket.
Diagram Description: Illustrates the main bed frame being raised slightly to align with the wing bracket attached to the side rail. The wing bracket is shown on the floor.
Step 4: Attach Bracket to Headboard
Attach bracket (A) to the headboard using the provided Hex Key (E), 4 Screws (C), and Washers (D).
Diagram Description: Depicts a Bracket (A) being attached to the headboard of the bed frame using Screws (C) and Washers (D), secured with a Hex Key (E).
