Vera Dream Storage Bed Assembly Instructions

Product Overview

This document provides assembly instructions for the Vera Dream Storage Bed and the optional Vera Dream Wings. Please ensure all parts and hardware are present before beginning assembly.

Vera Dream Storage Bed Assembly

Parts List

Hardware

Hardware bag included in side rails and slat box with red ribbon.

Assembly Steps

Step 1: Attach Side Rails to Headboard

Attach the side rails (2) to the headboard (1) using Wrench (C), four Screws (A), and Washers (B).

Diagram Description: Shows the headboard upright, with side rails being attached to its sides using screws and washers.

Step 2: Attach Slats to Side Rails

Attach the "L" shape slats to the side rails using two Screws (A) and Washers (B) for each slat.

Diagram Description: Shows the bed frame with side rails attached to the headboard. Slats are being positioned and secured to the inner sides of the rails.

Step 3: Attach Support Legs to Center Slat

Attach the support legs with levelers to the center slat. Adjust the levelers on the bottom of the support legs as necessary for stability.

Diagram Description: Illustrates attaching adjustable legs to a central support beam, which will likely be the main center support for the slats.

Step 4: Position Center Support

Place the center support piece (with attached legs) into the U-shaped slot on the bed frame.

Diagram Description: Shows a component, likely the center support beam, being inserted into a designated U-shaped fitting on the bed frame.

Step 5: Secure Center Slat

Secure the center slat assembly using Wrench (C), one Screw (D), and Washer (B).

Diagram Description: Details the fastening of the center support beam to the bed frame using a specific screw and washer.

Step 6: Insert Footboard/Drawer Unit

Insert the footboard storage assembly (containing drawers) into the bed frame.

Diagram Description: Shows the footboard section, which houses the drawers, being slid into place at the foot of the bed frame.

Step 7: Unroll Slats

Unroll the remaining slats onto the center slat, starting from the footboard and ending at the headboard.

Diagram Description: Depicts unrolling a bundle of wooden slats across the width of the bed frame, from foot to head.

Step 8: Final Verification

Verify that the slats are installed properly and that the legs are perpendicular to the floor for full support.

Diagram Description: Shows the completed bed frame, with an emphasis on checking the alignment and stability of the slats and support legs.

Vera Dream Wings Assembly (Optional)

Parts List

Hardware

Hardware bag included with red ribbon.

Assembly Steps

Step 1: Attach Brackets to Wings (Left Side)

Attach brackets (A and B) facing the left side to the wing, at the end of the slot, using Wrench (E), Screw (C), and Flat Washers (D).

Diagram Description: Shows attaching metal brackets to the side of a wing component.

Step 2: Attach Brackets to Wings (Right Side)

Attach brackets (A and B) facing the right side to the wing, at the end of the slot, using Wrench (E), Screw (C), and Flat Washers (D).

Diagram Description: Shows attaching metal brackets to the other side of a wing component.

Step 3: Position Bed for Wing Attachment

Raise the bed and position it so the side rail fits inside the wing bracket.

Diagram Description: Illustrates aligning the bed frame's side rail with the bracket attached to the wing component.

Step 4: Attach Wings to Headboard

Attach bracket (A) to the headboard, using Wrench (E), four Screws (C), and Flat Washers (D).

Diagram Description: Shows attaching the wing assembly to the headboard of the bed using screws and washers.

Additional Information (Page 6)

This section lists components for the Storage Bed Vera Dream, specifically the footboard and drawers.

Diagram Description: Shows the footboard and drawers, along with hardware for assembly. Step 1 illustrates attaching a component with a screw and hex key.