LIVING SPACES VERA DREAM STORAGE BED ASSEMBLY INSTRUCTION

Step 1: Attach Side Rails to Headboard

Attach the side rails (labeled '2') to the headboard (labeled '1') using the provided wrench (C), four screws (A), and washers (B). Ensure the rails are securely fastened to the headboard.

[Diagram: Illustrates connecting side rail '2' to headboard '1' using screw 'A' and washer 'B', with wrench 'C' nearby.]

Step 2: Attach Slats to Side Rails

Attach the 'L' shape slat (labeled '2') to the side rails using two screws (A) and one washer (B) per slat. The diagram shows the slat resting on the side rail's support ledge.

[Diagram: Shows attaching slat '2' to side rail '2' with screw 'A' and washer 'B'. Multiple slats are shown being installed.]

[Estimated time: ⏱️ 0:45]

Step 3: Attach Support Legs to Center Slat

Attach the support legs, each equipped with a leveler, to the center slat. Adjust the levers on the bottom of the support legs as needed for stability. The center slat may be U-shaped.

[Diagram: Shows support legs with levelers being attached to the underside of the center slat. Arrows indicate adjustment direction.]

Step 4: Position Center Slat Assembly

Place the assembled center slat (with support legs) from top to bottom into the designated U-shaped slot on the bed frame.

[Diagram: Illustrates lowering the center slat assembly into a U-shaped slot on the bed frame.]

Step 5: Secure Center Slat

Secure the center slat using the provided wrench (C), one screw (D), and one washer (B). The diagram shows a close-up of the connection point.

[Diagram: Close-up view showing screw 'D' and washer 'B' being used to secure the center slat with wrench 'C'.]

Step 6: Insert Footboard Storage Assembly

Insert the footboard storage assembly, which contains the drawers, into the main bed assembly. Refer to the drawer box for specific assembly instructions if needed.

[Diagram: Shows the footboard with drawers being slid into the assembled bed frame.]

Step 7: Install Slats

Unroll the bundle of slats (labeled '2') onto the bed frame, starting from the footboard end and extending to the headboard. Ensure they are evenly spaced.

[Diagram: Shows a bundle of slats '2' being unrolled and laid across the bed frame from footboard to headboard.]

Step 8: Verify Installation

Verify that the slats are installed correctly and that the support legs are perpendicular to the floor to ensure full support for the mattress.

[Diagram: Shows a side profile of the bed, highlighting the perpendicularity of the support legs to the floor for stability.]

Step 1: Attach Brackets to Left Wing Side

Attach the slot bracket (A) and corner bracket (B) to the left side of the wing. Use wrench (E), screws (C), and flat washers (D) for attachment. The brackets should be positioned at the end of the slot.

[Diagram: Shows brackets 'A' and 'B' being attached to the left edge of the wing using screws 'C' and washers 'D'.]

Step 2: Attach Brackets to Right Wing Side

Attach the slot bracket (A) and corner bracket (B) to the right side of the wing. Use wrench (E), screws (C), and flat washers (D) for attachment. The brackets should be positioned at the end of the slot.

[Diagram: Shows brackets 'A' and 'B' being attached to the right edge of the wing using screws 'C' and washers 'D'.]

[Estimated time: ⏱️ 0:30]

Step 3: Position Bed Frame with Wing Bracket

Raise the bed frame and position it so that the side rail (labeled '1') slides into the wing bracket (labeled 'B'). The diagram shows the bed frame being aligned with the wing.

[Diagram: Illustrates raising the bed frame and aligning the side rail '1' with the wing bracket 'B' attached to the wing.]

Step 4: Attach Bracket to Headboard

Attach bracket (A) to the headboard using wrench (E), four screws (C), and flat washers (D). The diagram shows multiple attachment points on the headboard for the bracket.

[Diagram: Shows bracket 'A' being secured to the headboard with screws 'C' and washers 'D', using wrench 'E'.]