VERA DREAM BED ASSEMBLY INSTRUCTION
Vendor Information
Vendor Name: LSMX1
Vendor Code: V-005852
Vendor Collection: VERA DREAM NON STORAGE
Provided by Living Spaces
Parts List
| Item | Description | Quantity |
|---|---|---|
| 1 | VERA DREAM HEADBOARD | 1 |
| 2 | VERA DREAM RAILS/SLATS | 1 |
| 3 | VERA DREAM FOOTBOARD | 1 |
Hardware
- A: 5/16-18X1" SCREW BUTTON HEAD CAP (X8)
- B: WASHER 5/16 PLAIN (X8)
- C: 3/16 SHORT ARM HEX KEY (X2)
- D: 5/16-18X1 1/2" SCREW BUTTON HEAD CAP (X2)
Hardware bag included in side rails and slat box with red ribbon to locate.
Assembly Steps
Step 1: Attach Side Rails to Headboard
Connect the side rails (labeled '2') to the headboard (labeled '1'). Use four screws (A) and four washers (B) for each side rail. Tighten using the hex key (C). The diagram shows the side rails attaching to the vertical sides of the headboard.
Step 2: Attach Footboard to Side Rails
Connect the footboard (labeled '3') to the ends of the side rails (labeled '2'). Use four screws (A) and four washers (B) for each side rail. Tighten using the hex key (C). The diagram illustrates the footboard attaching to the front ends of the side rails.
Step 3: Attach Support Legs to Center Slat
Attach the support legs, each with a leveler, to the center slat (labeled '3'). The diagram shows five legs attached to a slat. For adjustment, turn the levelers on the bottom of the support legs. Note: Center Queen Bed requires 5 support legs, Center CK Bed requires 5 support legs, and Center EK Bed requires 10 support legs.
Step 4: Place Center Slat Assembly
Insert the assembled center slat with legs (labeled '3') into the U-shaped slots located on the headboard (labeled '1') and footboard (labeled '2'). The diagram shows this piece being placed from top to bottom into the slots.
Step 5: Unroll Slats
Unroll the bed slats (labeled '2') starting from the footboard end and extending them towards the headboard end, laying them onto the center slat.
Step 6: Verify Slat Installation
Confirm that the slats are correctly installed and are perpendicular to the floor to ensure proper support for the mattress.
Vera Dream Bed with Wings Assembly
This section details the assembly of the Vera Dream Wings.
Hardware for Wings
- A: SLOT BRACKET (X2)
- B: CORNER BRACKET (X2)
- C: 5/16-18X1-1/4" SCREW BUTTON HEAD CAP (X8)
- D: WASHER 5/16 PLAIN (X8)
- E: 3/16 SHORT ARM HEX KEY (X2)
Hardware bag included with red ribbon to locate.
Wing Assembly Steps
Steps 7-9: Screw and Plate Adjustment
Step 7: Loosen screw (C) using wrench (E) by turning counterclockwise (lefty-loosey).
Step 8: Turn a plate clockwise and another counterclockwise. This step involves adjusting specific components, likely brackets or fasteners, by rotating them in opposite directions.
Step 9: Tighten screw (C) using wrench (E) by turning clockwise (righty-tighty), following the direction of clock hands.
Step 10: Attach Brackets to Wings
Attach slot brackets (A) and corner brackets (B) to the back and underside of the wings (labeled '1'). Use screws (C) and flat washers (D), tightening with the hex key (E). The diagrams show specific attachment points and orientations for brackets A and B on the wing component.
Step 11: Position Bed with Wings
Raise the bed frame and position it to fit inside the wing bracket system. The diagram shows the wing component (labeled '1') being aligned with the side rail and headboard, resting on the floor.
Step 12: Attach Brackets to Headboard
Secure bracket (A) to the headboard. Use four screws (C) and four flat washers (D), tightening with the hex key (E). The diagrams illustrate multiple brackets (A) being attached to the headboard, each secured by screws (C) and washers (D).
